E4200 PC connects to the router and the network home and says its connected to the internet but wont
Hello
I have an E4200 and upgraded to the Cloud Connect. It was buggy, and so I went down to the firmware before that. I have all the computers works well in the House except my office. It connects to the network, he can see the other computers on the network can still do a windows update. But when I go to use google chrome or internet explore it just won't connect to the internet. Has anyone already experienced this? It does not work either if it's a wired or a wireless connection, it was fine before the upgrade downgrade and following. It is on this desk that I installed and uninstalled cloud connection thew. I know enough to set up the network, but when it does not work... .so I'm lost for what to do. Help, please!
I did a restore of the system to a point before I upgraded to Cisco Connect Cloud, and that did the trick. Thank you for your willingness to help. All is well now.
Tags: Linksys Routers
Similar Questions
-
Our computers connect via wifi to a capsule of time to the airport and to the internet, but can't find the time capsule, nor can its hard drive. Y at - it a reset, we can try or he dies. It's only a couple of months.
Turn about your Airport Extreme for 15 seconds and then power back on. As soon as you see the green light, you should be able to see him for a minute or two in the Airport utility. In the affirmative, and see if you have Back to My Mac active. If so, disable it by removing all the e-mail addresses of the back section of my Mac. Then update your Airport Extreme. Work quickly.
Many have started having this problem within the last week, probably because Apple changed something in its servers CCMM. A real difficulty would come from Apple, but it should work if you currently have active CCMM.
-
I can't load ios9.3. I get a message that I am not connected to the Internet, but I check and I am connected.
Apple pulled 9.3 for some devices due to problems.
Just wait and try to come back later.
-
My husband and I share a PC. He has his desk top and I have mine, just that recently, I have not been able to connect to what anyone on my side of the PC, but its East side works well, it can connect to the internet, but I can't any idea what should I do? I ran virus scan and his side of own, cannot check the mine but cannot connect help please.
Hello
1. you remember to make changes to your computer, after which the issue started?
2. do you have a cable or a wireless connection?I would recommend that you follow these steps.
Step 1:
Test the issue in safe mode with network and check if that helps.
Step 2:
Configure the connection to obtain an IP address automatically.a. click "Start", enter "NCPA. CPL"(without quotes) in the search bar and press"Enter. "b. right-click on the network connection, and then click "Properties".If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.c. click Select 'Protocol Version 6 (TCP/IPv6) Internet' and then click 'properties '.d. check "obtain an IP address automatically" and "Obtain DNS server address automatically".e. click 'OK '.f. click Select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.g. check "obtain an IP address automatically" and "Obtain DNS server address automatically".h. click on 'OK '.Step 3:
Follow the steps in this article and check if that helps.
Why can't I connect to the Internet?
Steps are also applicable for Windows Vista.
-
I am connected to the internet, but it is said in the toolbar not connected and connections are available. There is only 1 link and I'm connected to it. How can I change display green bars, instead of grey bars with a yellow star?
As the title says.It's weird, and I think that this is the reason why some of my programs connect properly?Does anyone have a solution to fix this problem?Hi DamienDwyer,
1. are you referring to the status of job internet bar?
2 when the problem started?
3. have you made changes on the computer recently?Method 1
Try troubleshooting of network running.Use Network Troubleshooter event logs to solve network problems
http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problemsMethod 2
check the status in safe mode with network and display the results.Start your computer in safe mode
http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-modeMethod 3
I suggest you try the steps from the following links:Windows wireless and wired network connection problems
http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-WindowsWireless network card: frequently asked questions
http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions -
I am connected to the internet, but my network sharing Center proclaims that I'm not.
The paradox connected but not connected
I am connected to the internet, but my network sharing Center proclaims that I'm not. Because some of my programs believe later, they refuse to patch. Also, I used the antivirals ware, scans, System Configuration and deleted and later restored the wireless network.
Any help would be greatly appreciated. Thanks in advance.
Hello
1 reboot as often, this allows the refresh icon and also stops a few things of
interfere with the slot troubleshooting process.Do a 1 Restore Point then you can go back to where you were if necessary.
How to create a Vista System Restore Point
http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html------------------------------------------------------
Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
version - click the driver update (cannot do something that MS is far behind the pilots of certification). Do
It will be the same for network (NIC) card - then right click on the devices and UNINSTALL - Reboot -
update the driver stacks.Now go look at the site of the manufacturer of the system for the updated drivers.
After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
manufacturer of system become your backup policies).Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlDownload - SAVE - go where you put it - right click – RUN AS ADMIN.
You can download several at once however restart after the installation of each of them.
Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
updated drivers.If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
manually if you wish.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-----------------------------
Allow you to reset your TCP/IP stack just to make sure:
Start - type in search - ORDER - search box at the top of list and RIGHT CLICK – RUN AS ADMIN
Enter these one at a time (or copy and paste) and press ENTER after each
ipconfig/flushdns
nbtstat-r
nbtstat - RR
netsh int Reinitialis
netsh int ip reset
netsh winsock reset
Reset
----------------------------------
Make sure you know the details of connection to your wireless router - SSID and password.
You lose connection when you do and have to redo your logon.
Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
lower left click on merge or delete network locations - REMOVE all instances of your network (and the
others you don't use anymore) - REBOOT.---------------------------------
Other tips:If the use of a wired cable - Control Panel - device - network adapter - (NIC) Manager - double
Click Advanced settings and set the "speed & Duplex" 10 Mbps full duplex and then try 1/2
double-sided. Be sure to APPLY / OK. Maybe some help here: (don't forget the answer is)
complicated because there's probably more than one single thing, the origin of the problem)Others.
http://www.how-to-hide-IP.info/2009/05/16/CYBERGHOST-VPN-fixing-network-cable-unplugged-error/
http://www.annoyances.org/exec/Forum/WinXP/1109372091
There are many causes, one of which is the small monitor pays attention to the evil network device.
You can try to disable any other network such as WiFi device and reboot to see if that has an effect.Still a problem of equipment such as a loose network card that is not properly attached to the computer can
cause this.http://compnetworking.about.com/od/WindowsNetworking/f/cableunplugged.htm
I hope this helps and happy holidays!
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
I am connected to the Internet, but my new Airport Express Terminal still flashes orange. Any ideas?
The utility airPort on your Mac or iPhone / iPad is going to tell you why the AirPort Express is complaining... and offer a fix for what he thinks is wrong.
If you are in need of more details, we will need to know if you are using a Mac or iPhone / iPad. Mac, what operating system they are running to be the case as well.
-
I am connected to the internet, but I do not know why I can not use some programs... someone please help me I am so frustrated!
Hi Alejandrac_677,
· What version of IE are you using?
· What operating system is installed on your computer?
· What happens when you try to access Internet Explorer, you receive no error message?
· How long have you been faced with this problem?
· You did it last changes before the show?
Please see the following to find out about Internet Explorer, and operating system.
Find out what version of Internet Explorer you are using
http://Windows.Microsoft.com/en-us/Windows7/find-out-which-version-of-Internet-Explorer-youre-using
What version of the operating system Windows am I running?
You can also check:
Why can't I connect to the Internet?
http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet
Please provide us with more information about the issue so that we can help you in a better way.
-
Hello
I have recently setup a wireless connection from my laptop on Windows 7 works very well. but I have a laptop with windows xp that show an icon connected to the internet, but I can't access the internet can you please help me.Thank youoriginal title: wireless internetDo you receive kb from the internet source or is it local only, and when trying to access the page host does upward with the site not found or 404 error, have you tried to repair the connection, it could be your antivirus protection is blocking the signal.
-
I have a wireless router Belkin g with 1 Server 2003 cable and 2 xp machines and 1 machine vista wireless. My problem is when you transfer files to the internet, the router disconnects from the internet, but the network remains intact. I cannot remote in all computers, but not internet. Once I have restart the router, everything works fine. I was wondering if anyone else has had this problem and how to fix them.
original title: problems with the router.I have no solution for you. It seems more likely to me that it is a hardware problem - but if it was related to traffic, I would expect that the problem on the downloads more downloads.
In addition to DSL reports, you could try to ask some of the forums that specialize in the updated firmware for wireless routers. This is not to say that you need to install the modified firmware (although there may be good reasons to do so), but people who do usually firmware mods are much how the equipment works and what might be its potential failure modes.
Is one of the best-known sites DD-WRT.com, but there is one list of other here: http://en.wikipedia.org/wiki/List_of_wireless_router_firmware_projects the firmware on these sites was originally designed to run on Modem Linksys WRT54G, but applies generally to Linux with chips Broadcom - based wireless routers and DD - WRT claims that its firmware takes care of some Belkin routers. If your router is one of those on what DD - WRT will work, there will probably be someone in the forum there will have something for you. See the list here: http://www.dd-wrt.com/site/support/router-database
-
Why my internet has stopped working
My computer says that it is connected to the internet but the HTTP 500 Internal server Err error rises. How I get working again? I have another computer in the House and that works very well.http://support.Microsoft.com/kb/321448
In some cases, you must remove the cookie as well. -
IE connects to the internet, but another program get a cannot connect error
Using Vista, my internet explore is connected to the internet, but when I have other programs trying to access the Internet, I get a Cannot Connect to Internet Message. What is the cause?
Hello
I suggest you try resetting Internet explorer and check to see if it helps:http://Windows.Microsoft.com/en-us/Windows-Vista/reset-Internet-Explorer-7-settings
It will be useful.
-
Original title: connection problem
I'm unable to access my computer (windows 8) with my microsoft account. The password works for the connection to outlook on the internet, but not the computer.
The message I get when trying to connect is simply that I cannot connect you at this time and that I should follow a link to reset the password - what I've done without result. The computer is connected to the internet.
Hello
Thanks for posting your query on the Microsoft Community.
With the publication of the description, I understand that you are unable to access your computer using Microsoft password account on the machine Windows 8. I will certainly help you get this problem.
I would be grateful if you could help me with more information:
1. Since when you are facing this problem?
2. What is the exact error you receive by accessing the computer?
I would say to you follow the suggestions provided by Cliff_N responded on 7 December 2012 in the below thread Microsoft:
Important information: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.
Note: When updating, the applications you have installed Web sites and DVDS is deleted. The applications provided with your PC and applications that you have installed in the Windows store will be resettled. Windows puts a list of apps removed on your desktop after you refresh your PC.
For more information, you can consult the Microsoft article.
What to do if you forget your Windows password
http://Windows.Microsoft.com/en-us/Windows/what-do-forget-Windows-password#1TC=Windows-8
Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.
-
I am fully connected to the Internet, but when I click on my home page and even several other pages, including Windows Live Mail, I get an error message that my DNS server is not responding. How can I work around this problem and to connect to the Internet anyway?
You want to be sure that you use the right setting for your DNS server. You can move this in your browser using the digital URL for the what you want to access web sites. You will find them by using the PING command at the command prompt. Hold the Windows key and press R. Then type CMD and press ENTER. Then enter for example to get the address of the web site of MS PING WWW.MICROSOFT.COM.
Unless otherwise directed by your Internet service provider, you want TCP/IP settings to "obtain an IP address automatically" and "Obtain DNS server address automatically". To do this click Start-> Control Panel-> Network Center and sharing-> view status.
Then click on properties.
From there, click on Internet Version 6 Protocol and properties.
Click on the two radio buttons to "obtain an IP address automatically" and "Obtain DNS server address automatically". Click OK.
Then click Internet Version 4 Protocol and make the same changes in what concerns the version 6.
I hope this helps. Good luck.
Good luck.
-
Windows Media Center tells me that I have sm not connected to the internet, but I'm out of windows media center I can access the internet. Why?
Disable the firewall and check the connectivity in media center.
Maybe you are looking for
-
View Portege M400 on TV?
HelloI have a portege M400 regular and I want to display on a TV. I bought a simple vga to s-video cable on ebay... What don't get me? The seams of the video card to be able to do this option... and the clues...Thank you
-
1 when I click Update to check the last version I get the error: could not connect to the server to update the same if I'm connected to the internet and the use of other sites.It is no longer in favour of SimplePass or what? 2. I tried to update is b
-
Satellite L300D WIN XP drivers needed
Dear all, I have a problem with my laptop Toshiba L300D quite new. My younger brother wanted to install XP instead of Vista.The hard drive has been formatted and installed WIN XP Professional. Now, it has the problem that the laptop is not working pr
-
Labview that is running on a computer without write access to the installation directory?
Hello A client of ours wondered if we can run our Labview executable and runtime on their computer without having no write access to the installation directory? It is quite easy to change so that our program writes its log files to another drive on t
-
Disadvantages of using DAQ Assistant
I need 2 analog inputs continuously at 5-10 kHz from the sample and then use a combination of producer consumer and State Machine for the processing of data in real-time. In most parts of the example I've seen, people always use Subvi of data acquisi