EA7500 and three RE7000s - seamless roaming

Similar Questions

• Seamless roaming with EA7500 + RE7000 the two AP work?

  I have a wired router provided by my ISP at home and a few wireless (wired connection to the router, DHCP off) covering the rooms. The experience of homelessness is terrible, and I am considering buying an EA7500 and a RE7000 to replace my existing APs.

  But after this post EA7500 is not compatible 802.11r. It is a surprise for me. I would like to know which of the following configurations provides the best mobile experience, or are they the same?

  (a) 1 EA7500 + 1 RE7000, both working as AP, wired to the router;

  (b) 2 RE7000 works like AP, wired to the router.

  With option one) I also use EA7500 for storage network etc., but homelessness experience matters more for me.

  @Carolina

  If the two Linksys RE7000 are both connected to the router, they will act as an Access Point, however, adding another extensions (RE7000) wireless to remote locations is possible depending on the coverage of your network. BTW, check out this link how to configure 2 Linksys RE7000 for seamless roaming. You can also check out this other link to set up your RE7000 with a Linksys Max-Stream router.

  Jay-15354

  Linksys technical support

• DV6409ca No. Wireless and three device Base system in the Device Manager

  I have a DV6409ca SNcnf73202t7 and ran Windows XP on it flawlessly for about a year.

  Last night I asked my laptop and this morning I woke up to the orange light of death on the front of the computer for the wireless and three newspapers of device Base system in the Device Manager. They run:

  Bus PCI 7, device 5, function 3

  Bus PCI 7, device 5, function 2

  Bus PCI 7, device 5, function 4

  I tried making restoration of the system, the removal of the chipset drivers / wireless/network and reinstall in safe mode and the search for solutions to many other people tried to make their wireless work.

  Any help would be appreciated. Thank you

  Hello:

  You must download and install the Ricoh 5-in-1 card reader driver support for your laptop and driver page.

  Go to Device Manager and expand network adapters.

  Is the model of your wireless poster card he or she has completely disappeared from the Device Manager, does not come under the section of the network cards, or in the General list of devices such as a network controller?

  If she disappeared from the view, 99% chance the connection from the motherboard to the card slot plugs into is fried.

  This is a very common problem with the dv6000/dv9000 models.

• computer not start, receive a beep long and three short beeps

  Just installed the update video drivers ATI disk mag APC program and when I tried to start computer I'll beep long and three short beeps but nothing else happened.  The answers to the problem

  These beeps are error codes of the BIOS POST (Power on self test). A series of long and short three is usually a related video.

  This is usually caused by a problem with the video card or the memory on the video card. It can also be a motherboard problem. I don't know how this is related to the update of video drivers, unless something was going wrong catastrophic.
  If it is a PC with an independent video card, you can try physically re - a corner of the card or install a new card, so you can have access to the computer for a further diagnosis. There are not many other things that can be performed before the replacement of hardware components (motherboard, video card, etc.).

• EA7500 and PS3"

  Hi all

  I need help.  Husband and I implemented the new router, EA7500, and it works very well with all devices except for our PS3.  The PS3 is unable to locate the SSID.  Any ideas?

  After speaking with a representative on live chat, for anyone in the future, who has this problem.  Here's the resolution.

  1. under the router settings, please click on wireless.
  2. According to the basic wireless setting, click on change for 2.4 GHz network.
  3. we need to assign 2 another network name (SSID) of 5.0 GHz and 2.4 GHz for optimal wireless performance and to avoid interference of wireless signal. For example, MyNetwork for 2.4 and MyNetwork5 for the 5.0 GHz.
  4. for the 2.4 GHz network, network Mode must be set to mixed and channel width 20 MHz channel 11.
  5. set the Security Mode to WPA2 personal network 2.4 GHz and 5.0 and enter your wireless network password in the password field.
  6. the security of your wireless network key is case-sensitive. Ensure that you write correctly.
  7. click on the button to apply.

  Worked like a charm for us and I hope that for you also!

• Tap to click and three fingers slide no longer work after El Capitan update - MACBOOK AIR early 2014

  Things no longer work after the update are:

  1. TAP to click (I checked it on SYS PREF > TRACKPAD > tap-to-click)

  2 finger three windows

  3 Thre finger of several files and text selection.

  I have selected three fingers slide accessibility and options of the trackpad iv done 4 fingers to mision statement and app expose, but the problem is that these feature mission statement and the rest three fingers still work. :@

  It was just beautiful in yosemite please give a solution.

  Please read this message before doing anything.

  This procedure is a test, not a solution. Don't be disappointed when you find that nothing has changed after you complete it.

  Step 1

  The goal of this step is to determine if the problem is localized to your user account.

  Select the feedback connections* and log in as a guest. Do not use the Safari connection only 'user comments' created by 'find my Mac '.

  While signed in as a guest, you will have access to your documents or settings. Applications will behave as if you use them for the first time. Do not be alarmed by this behavior; It's normal. If you need any password or other personal information in order to complete the test, save, print, or write them before you start.

  Test while signed in as a guest. You have to re-create your trackpad settings. Same problem?

  After testing, log on to the guest account and in your own account, disable it if you wish. The files that you created in the guest account will be automatically deleted when you log out of it.

  * Note: If you have enabled 'find my Mac' or FileVault, then you cannot activate the guest account. The login 'User comments' created by 'Find my Mac' is not the same. Create a new account to test and delete it, including his home folder, after testing.

  Step 2

  The goal of this step is to determine if the problem is caused by changes in the system of third party that load automatically at startup or logon, by a device, by a police conflict or corruption of system files or some system caches.

  Please take this step regardless of the results of step 1.

  Disconnect all devices wired except those required to test and remove all the expansion cards from secondary market, as appropriate. Start in safe mode and log on to the account of the problem.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, with limited graphics performance, and some things work at all, including an audio output and a Wi - Fi connection on some models. The next normal boot can also be a bit slow.

  The login screen is displayed even if you normally connect automatically. You need your password to log on. If you have forgotten the password, you will have to reset it before you begin.

  Test in safe mode. Same problem?

  After testing, restart as usual (not in safe mode) and make sure you always have the problem. View the results of steps 1 and 2.

• Cisco SPA232D ATA and Cisco SPA302D Wireless roaming handset

  I read the documentation of SPA 232D and I see that it supports up to 5 stations 302D SPA.

  In this project, I have 4 floors and we need a total of 15 phones:

  3 - basement

  5 - ground

  4 - first floor

  3 - second floor

  When the person is using the basement 302D phone have no reception when they walk on the upper floor.

  Can we do roaming between 232D? Is it possible to interconnect their? The range in the documentation may not be enough.

  What would be the recommended Cisco solution for this, we want to use DECT.

  Range: Indoor: 165 ft (50 m). Outdoor: 980 ft (300 m)

  Thanks for thinking of the spa232d for this project,

  Unfortunately with the current firmware it does not support combined roaming between base stations.  There is not an easy way to transfer between units handsets (you must unsubscribe from a base station and register again with the 2nd spa232d).

  The distance of the datasheet is optimal in a perfect environment, and I expect to be a little less real world.

  I woud suggest get a spa232d and a spa302 (maybe a dealer demo unit) and test range on the customer site.  Basically, do a site survey to see where the best place in the unit.

  If you need more 5 units on a floor, or signal will not reach both ends of the beach, 2 - spa232d devices may be necessary.  Some devices would be recorded to one, some to the other.

  There is good documentation on configuration and management with the device calls here.

  SPA232D & SPA302D: Introduction to the call routing scenarios advanced

  https://supportforums.Cisco.com/docs/doc-30269

  Let me know if you have more questions.

  Dan

• BlackBerry, change of sim card and ID blackberry Smartphones roaming charges

  I did a little research and although have found similar cases, I'm not quite sure if this has been covered completely. Please forgive me if it has.

  I'm going abroad in Germany for a year, and it is useless to cancel me my current plan of the monthly British payroll with Vodaphone. As far as I know my blackberry is unlocked at the international level - I put an old, German o2 pay as you go sim in my phone. Seemed to work very well (sign of o2 Germany, received a message on homelessness in the UK, etc.), but I had no credit so couldn't test. I registered again my user ID of blackberry on my home wi-fi. But other that I couldn't do much to verify the extent of my use.

  However, I heard various accounts of not being able to use e-mail, internet, wipe the contacts, etc..

  If someone could clarify this, here are my questions:

  • If I take my sim UK vodaphone, is anyway I have accumulate roaming charges? Is my blackberry ID, potentially with a new German supplier, related to my old?
  • Will he make any question tries to access my email, bbm, whatsapp, etc., with a different number and in a different country.

  One has experience in this area, in Germany (a long shot), Europe or world? It seems that the whole ID blackberry complicates things.

  My phone is a Blackberry Bold 9900, AFAIK its software wise update - I have updated today with the "Bundle 2061 7.1" I think.

  Thank you

  J.

  Hello and welcome to the community!

  There are a number of problems to know for what you propose... Here are my thoughts... (Note that I have traveled internationally widely enough with a BB).

  If you activate a plan of itinerant international with the support of your home, you should be able to keep your current SIM card in your BB and have all the features anywhere where you are allowed (according to what your home carrier active). Costs are not small in general, but your home operator is the only entity that can tell you if it will work and for how much money. My personal experience with this method was difficult, it took two 'stranded' international travel before my carrier home could properly configure my account for full international roaming I needed. And once my BB was out of my home network, there was nothing else they could do... so the two 'fail' the TRIPS Agreement.

  Given that your BB is unlocked, you can use it on other carriers, simply by changing your SIM card. But with BB, it is not quite as simple as that.

  No BB does exist (indeed, no device anywhere that I know of) that has all the radio technologies/frequencies within the view are just too many in the world. Thus, your first task is to ensure that your BB has the ability to the same function on the support networks you want to use it on. You must study the capabilities of your specific BB against the requirements of networks you will operate on... you may need to ask those network operators for more details.

  If this element is satisfied, which then verifies that you have services at the level of the voice (calls, voice mail, SMS). But for level data services, increase complications.

  Each company chooses patterns specific to BB (by model number) that they will promote "automatically". I do not know the carriers that have their network configured to support all the model numbers of BB. If the carrier you wish to automatically use your BB model number on media, then their system will be able to automatically deliver to your BB Service books required in order to activate the BB exclusive services (email, BBM, etc.). But, if their network does not natively support your specific model BB number, then their network is not likely to be able to automatically deliver these Service for your BB books... which will prevent the use of their network BB exclusive services. Again, you must inquire carriers on which you want to run if your specific model BB number is supported by their network for the automatic distribution of maintenance book.

  In addition, it is to ensure that your home carrier frees your BB PIN of their system of BIS. A BB PIN can exist in only one carrier BIS system anywhere in the world... so if your home carrier doesn't release him, then the other carrier will not be able to allocate a BIS account for you, and you still won't be able to use services BIS of them. In this case, it is usually a matter of contact your supplier of home and convince them to release your BB PIN of their system of BIS.

  If all goes well and all the conditions are met, then it can be quite transparent to switch between carriers, simply by changing your SIM card, ensure that each SIM card includes good BIS Services this carrier of course.
  But if anything this either in the chain requirements above fails, it can sometimes be frustrating to make the things work pretty well (reminds me of my two "failed" international travel).

  So, with all this as preamble, now to your questions...

  jpfp wrote:

  • If I take my sim UK vodaphone, is anyway I have accumulate roaming charges? Is my blackberry ID, potentially with a new German supplier, related to my old? J.

  Given what you describe, I see no for Vodaphone to charge you roaming charges. Without their SIM in your BB, your BB may not even try to use any resource of Vodaphone. But, you will need to get confirmation of Vodaphone on this point... so that they control all services, billing, etc. for your account. BB services you are subordinate to your main carrier services... you need the services of the main carrier to provide network connectivity services BB riding on this network connection.

  jpfp wrote:

  • Will he make any question tries to access my email, bbm, whatsapp, etc., with a different number and in a different country.

  There are always opportunities for questions. When you use a different SIM card, you are constrained to some services that provide the SIM. If it does not, for example, BIS level services, then you won't access to people. Similarly, if there is some government restrictions for some services, you can be restricted from that as well. If you get a SIM card with full services of BIS and, as described above, you spent all of the required components that I have listed, then you should be able to have all the services you listed. It is possible that you may need to reconfigure your email... There are stories about these configurations if shattered when change carriers... but the BBID integration is intended to facilitate this exact type of change of carrier, so it should not happen. But don't we can, of course, no promises.

  Good luck!

• ASA with A/A and three router ISP links

  Can someone help me, I have a problem I need to connect two ASAs with active and I have three routers to three Internet service providers, how do I optimize the gateway redundancy and load balancing.

  and I can use the router to ASA's private beach.

  Another Question is, do I really need host proxy server-based internet access.

  Please help me.

  Concerning

  One solution is to use the Protocol GLBP routers (OSPF in not available in A/A...).

  "GLBP offer deals on several routers (gateways) load balancing using a virtual IP address single and multiple virtual MAC. Each host is configured with the same virtual IP address, and all of the routers in the virtual routing group are involved in the transmission of packets. »

  GLBP group-load balancing [dependent on host: alternating | weighted]

  (see feature cisco IOS to IOS and hardware available browser.) .

  http://www.Cisco.com/en/us/products/ps6550/products_white_paper09186a00801541c8.shtml

  HTH.

  Roberto

• Conferecing design of a driver and three vTS 8-core system

  Hello

  We have an organization with 14 endpoint SX10, who must gather in a conference room large with 14 members full HD at the same time.

  Thus, it will be programmed with the simple working solution: three servers 8 strands vTS 4.2 under control of a virtual 4.1 conductor XC

  My question is: can we consolidate this vTS servers to achieve the maximum capacity of a conference with 15 screens fullHD?

  Or with this configuration, we can collect only 5 fullHD users at the same time?

  Hello

  It would be not possible to cluster vTPS because it is only available for 8710, 820 and 310/320 GST.    You could create a conference and a waterfall for the two additional vTPS cascading.  Note the links of the waterfall are limited to 720p30fps video hand and will consume about ~1/2 licensed screen by cascade.   The vTPS Conference begins book total license about ~ 1 screen for reservations of two cascade and on each vTPS additional about License 1/2 screen will be reserved.

  -Jonathan

• X 230, Intel HD 4000, dock and three monitors, how?

  Hello

  I just got new X 230 (makes 12/12). It has intel HD 4000 and processor i7-3xxx-series.

  I also got dock (the usb3 support).

  I have foud some topics saying that x 230 would support 3 monitors, but how?

  I have 3 x full HD monitors, 2 of them is connected with other with VGA and DVI to dock to dock.

  Windows screen settings allows me to activate the 3 monitos, but custom 3rd "wake up" and after that windows manager reopenin of screen it says that 3rd monitor is "disconnected". The Intel tool provides only option for 2 monitors.

  So, it is possible to activate the 3rd monitor?

  Hey there styleza,

  Thanks for clarifying the dock you are using by comparing what you found there to the PSRef for your machine, it doesn't seem to be the case. The PSRef States:

  "Intel HD Graphics 4000 in processor, supports external analog monitor via VGA and digital monitor via Mini Display Port; supports two independent screens. "Research on all for X 230 PSRef sheets, I agree, it doesn't seem Optimus technology was available for this machine as all PSRef sheets I could find for X 230 different configurations list only the Intel HD Graphics 4000. Sorry to be the bearer of bad news.

  At the very least, I hope this clarifies things for you.

• I bought for the CS6 design standard last year and had to disable and uninstall due to factory reset on computer, now when I open my products purchased to redownload my product, it won't let me? It is grayed out and thre no other links are available

  I bought the standard CS6 design last year and had to disable and uninstall due to factory reset on computer, now when I open my products purchased at re download my product, it won't let me? It is grayed out and there is no other link available for download?

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  -Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html

  -Cloud Getting Started https://helpx.adobe.com/creative-cloud.html

  -you will need to enter your original serial number during the installation for non-Cloud programs

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• I want to update the cloud creative and three hours, it remains at 2% and there is the Message: "connection to the server is established."

  

  Restart your computer and try again.  you lost the connection.

• Cisco Aironet AIR-SAP2602I-E-K9 WAP config autonomous and roaming

  Hey guys,.

  I'm quite 'green' where wireless technology is concerned, but have a few questions, I was hoping that someone can help me with that.

  I have a number of AIR-SAP2602I-E-K9 from WAP that I would install in a standalone configuration (no controller). These will connect in our infrastructure from switch L2 giving access to our corporate network to wireless devices activate. In total, I have 10 WAP which will focus on 2 floors in our office building. I would like to set up seamless roaming allowing users to walk around the building without noticing that their device connects from a WAP to the other.

  I guess I just configure each WAP individually with its own static IP address and configure the SSID / wireless network / security but I am wondering if there is a method to export the config filled from a WAP and import in other in order to avoid the obligation to re-create the SSID and the configuration on each WAP again and again. I'm also not sure to know how then would set up roaming between the WAP and also how their awareness of each other (because I'm sure they should be to allow transparent roaming). I can't find any real documentation specifically this - only on controller based deployments.

  Pointers would be greatly appreciated.

  Thank you very much to anyone who takes the time to read this message and reply.

  Thanks in advance.

  Must be configured, no, but if your voice using wireless, you probably need to or if you also have sensitive applications.  The reason is the time it takes to perform a roam. If you watch this doc, go to the homelessness section and it will show you a few times homeless.

  http://www.Cisco.com/c/dam/en/us/TD/docs/voice_ip_comm/cuipph/7925g/7_0/...

  -Scott

• Activate both drag the lock and drag three fingers

  I tried to activate the TWO drag the lock AND three sliding your finger on my new MacBook Air shape some time and have not been able to do.

  I have an older MacBook Air and an older iMac and on these two computers, it works (it didn't come pre-loaded with El Capitan, they have been 'improved' to El Capitan).  On both I can drag a window using both drag lock AND drag three fingers.  However, I am unable to do it on this new computer.   Is the any way to implement?

  Any ideas?

  Hi Joel,

  Options to drag in El Capitan are discussed in this resource:

  OS X El Capitan: mouse & Trackpad pane accessibility preferences
  https://support.Apple.com/kb/PH21509?viewlocale=en_US&locale=en_US

  The trackpad options

  Allow drag

  Check the box to be able to drag items.

  To set sliding options, click on the context menu, and then choose an option:

  without slide-Lock: double-tap an item, and drag it without lifting the finger after the second tap. dragging stops immediately when you remove your finger.

  Drag lock: double-tap an item, and drag it without lifting the finger after the second tap. dragging continues when you remove your finger and stops only when you type once the trackpad.

  three fingers slide: move an element with three fingers. dragging stops immediately when you lift your fingers.

  Take care