Electrical print

Similar Questions

• Electric pen failed on the HP Deskjet F4210 AIO printer

  Hello world!

  I'm new here; I come with the hope of finding help here, which is not possible to find on the official web page of HP.

  A month ago I bought the original HP cartridges 300 XL Black and 300 Canadiens XL. After you install the printer HP Deskjet F4210 all in one started blinking light at tricolor cartridge and the printer does not work. HP Solution Center shows the message - electric pen failed print cartridge error. Depending on the reason for troubleshooting can be bad cartridge also.

  Unfortunately I can not communicate with HP support by mail, there is no possibility to pass, even though I bought my printer last year, according to the rules of the EU it is guaranteed 2 years, it can also be fault on the origin, but HP print cartridge ignore all these fact and it is informative, that according to their data is my printer out of warranty and there is no possibility of mail to HP technical support , or contact HP support on any other way. I am therefore very disappointed with HP's attitude to their customers...

  Then I would ask for help, if this is someone who can tell me, if this failure report " electric pen failed" means default on the printer or the print cartridge?

  Thanks to all who have answers

  You can contact HP as shown here. Generally, the failure you describe would be the cartridge, or the electrical connections between the contacts of the cartridge and printer.  You can check the warranty of the cartridge as shown here.  Try cleaning the contacts of the cartridge as shown here.

• Multifunction color HP LaserJet Pro 200: I can't print to my HP printer using wifi, it was working and stopped after the electricity blackout

  I got my printer to print via wifi and it was working fine but as the power went out a few seconds this morning, it will not be printed.  I even reset the wifi but does not always print.

  Well, for this issue:

  1. Make sure that the printer is plugged directly into a wall outlet, not a surge protector.
  2. Turn the printer off.
  3. While the printer is turned off, disconnect the power cable from the back of the router for a minute.
  4. When the lights come back on the router, turn on the printer.

  Now, on the printer, click on the wireless icon that looks like a radio tower. If you see a line indicating the status: not connected, click on settings and Wireless Setup Wizard to connect the printer to your network.

  Finally:

  1. Click on start and open devices and printers.
  2. Right-click on any icon of your printer listed.
  3. Click on remove the instrument.
  4. Click Add printer, and follow the prompts to add a new queue for your PC.

  Please let me know the results after following the above. If you are able to print, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Some PDFS are print with empty boxes, replacing the text

  I have some of my electricity and gas supplier invoices and invoices are printed with squares displayed instead of text. I have already restored the book of fonts for the default fonts. I have no problem with the display of these bills on my computer. I have another PDF files and they all are printed correctly. If I open the PDF file that is badly printed and export it to PDF in PREVIEW app, the output is the same as on my printer. I tried to restore all the fonts by default those and I tried to reinstall OSX update with update combo, always the same.

  What else can I do to restore the normal print mode?

  

  

  Any who have had the same issue guys?

• My printer has an error 0xc19a0003 message. HP photosmart Plus

  I have the hp photosmart printer more.  CN218A product number and model number B210a.  It has been printing fine until today and it says 'system failure-0xc19a0003 of ink '.

  I turned the printer market even as it says on the screen and it did not help.  I also unplugged the printer from the computer and making electric and re-tried to no change.

  Help, please!

  Normally, an ink system failure message points to a problem in the printhead of the printer. This document will take you through a few things you can try to do to solve the problem. If this does not work, check the date on the print head. The day is the print head was performed. The printhead warranty expires two years after that date. If the print head is under warranty, contact HP for a new. If the print head is out of warranty, follow the steps in the post of Bob_Headrick to do a physical cleaning of the print head nozzle. Does not use the post to Bob_Headrick if the printer or the print head, is still under warranty. If this does not work, you can contact HP to buy a new printhead, or you will need to get a new printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.
  
  HP Technical Support call case form:
  http://goo.GL/w7Hgh

• HP6520 ALL IN ONE PRINTER: BLACK INK WILL NOT PRINT

  I TRIED ALL THE PROPOSED SOLUTIONS.  NO WORK FOR ME.  I HAVE TRIED SEVERAL TIMES TO RUN THE CLEAN CARTRIDGE HEADS.  SAME RESULT (WASTED A LOT OF VERY EXPENSIVE INK IN THE PROCESS).  ANOTHER USER HAS SUGGESTED TO USE SOLVENT TO CLEAN A CLOGGED INKJET PORT.  I DIDN'T KNOW WHERE REPRESENTATIVE HP APPROVED THAT.  THE PAGE OF DIAGNOSIS THAT PRINTS AFTER HAVING CARRIED OUT THE SYSTEMATIC CLEANING HEAD PRINT BLACK TEXT, BUT THE BOX FOR BLACK PRINTING IS TOTALLY WHITE.  IS THERE ANOTHER SOLUTION TO TRY?  Help!

  The printhead on the HP Photosmart 6520 is not designed to be removable by the user.  While you can find messages with information on the withdrawal of the printhead for soaking, it's really not recommended.  If you decide to do this don't forget to read the entire thread, these discussions often end with a printer damaged due to damage or damage to the encoder system, electrical connectors which can make the printer unusable.

  You may have already taken the steps of troubleshooting in the paper here, if not go through each of them in order.  Check the vents on the black print cartridge and that it sits correctly.

  If the above does not solve the problem you could try manually to clean the printhead, as described in the post here for a different but similar printer.

  Note that the printer uses a mixture of color and black inks to print a diagnostic page.  This is so that the information can be read even if black or one or more colors do not work.  Although it may seem from this page your black works that is unfortunately not.  You can simulate this by selecting "Photo paper", as the media type in the driver, it would force the printer to use the same color ink to print black text.

• 4630 HP for Mac: HP 4630 for Mac printer will print but no departure will scan

  4630 for Mac HP printer will print but will not scan. New & installed software that recognizes the print configuration and computer. When ask to scan get message see this "scan to PC". Can't find where to put "scan to computer".

  Thank you

  Hi @venny1,

  Welcome to the Forums of HP Support!

  I see that you are unable to scan to your Mac computer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  To activate the scan of the computer, see the procedure below:

  Restart devices and check the settings of scanning driver

  Restart the computer and the printer can restore the connection scan options analysis, and then check the settings for scanning on the Mac.

  1. Turn the printer off.

  2. Make sure that the printer power cord connects directly to an electrical outlet and not by a limiter the power strip or surge protector.

  3. Close all programs currently running on your computer, and then shut down the computer.

  4. Turn on the printer.

  5. Turn on the computer.

  6. On the desktop, double-click Macintosh HD, click Applications, click the Hewlett-Packard or HP folder, and then double-click the HP utility.

     NOTE: If the HP utility is not in the folder, go to the step install the software for your printer HP.

  7. Under scan settings, click Scan of the computer, and then make sure the enable scanning to computer checkbox is selected.

  8. Try to scan.

  If the error persists, proceed to the next step.

  Follow all the steps in this guide, if this problem persists:

  • HP printers - WIRELESS card Scanner is lost (Mac)

  I hope this information is useful. Please reply to this message with the results. Good luck!

• HP Photosmart Plus B209A does not print black ink despite trying two separate NEW ink cartridges black

  HP Photosmart B209A more

  MAC

  No error messages but trying to align or check colors - black doesn't print at all

  No change - knew ink was low so I tried to install a new black ink cartridge - then one day later tried an another new black ink cartridge

  I tried all the techniques of "Troubleshooting" listed on the page Web - align, clean the print heads, install the new cartridges, looking for trouble with the vents, etc.  I have only used HP ink cartridges.

  Hi abruce,.

  Usually, it is a result of dried/clogged ink nozzles in the printer or the print head.

  According to some other users on the forums, you can remove the print head (use this guide if you are unsure how: http://support.hp.com/us-en/document/c01944580)

  Make sure the cartridges are removed from the print head

  Dive head in hot water, nozzles downwards. (about 1 in. of water) and leave any residue of ink to flow. This process should take about 15 minutes. Ensure that the print head is completely dried out and there is no moisture in the electrical contacts or the rest of the part.

  I hope this helps!

• Want to 5530:5530 does not print black

  5530 printer worked very well. Black print cartridge ran out of ink. Replace the cartridge-no black printing, single color.  Thought that the replacement could be a dud. Put another in (both HP brand, out of the box). Still no black printing. Has made many attempts cleaning via the screen and computer connected with USB. Nothing. It prints a blackish color when I took out cartridge black - using composite of tri color cartridge.  Removed the cartridge, turn the printer power off, turned back, left overnight, unplugged, ran doctor Scan.  Still no black printing.

  Why this suddenly wouldn't work not afte replace this cartridge?

  Hi @Weaver1953

  Do you receive for example error messages missing cartridge? Try to clean the little electrical contact pads on the back of the ink cartridge and also take a look at where they are sitting in the printer to make sure that nothing has been damaged when you have replaced the cartridge empty. Sometimes if they are not aligned properly it can cause an error of rejection.

  However, if the printer accepts the cartridge and print, but the black ink is just absent, this suggests a problem with the cartridge and not the printer. If this is the case I suggest to get the cartridges to where you bought them or you could try calling the phone support, you can benefit from replacement cartridges. Theres a link below for phone in the world supported by the numbers:

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  I hope this helps!

• Why is my imac printing docs pdf with squares instead of text

  I use OS X 10.9.5. When I want to print a pdf document was sent to me from an external source (for example, my electricity bill) the document is printed with squares where the text should be.

  Sometimes if I get an overview of printing, it will look OK but always printed with squares/no text, and sometimes it shows squares in the preview. I was not able to determine a trend.

  I tried to print the docs to two printers (HL 2140 Brother and Epson WF3620) with the same result. I can't find that someone has posted the same problem in any forum...

  If there are small places where individual letters should be, it's a problem of compatibility of fonts.

  If you print from Acrobat, you can work around this by using the option 'Print as image' under 'Advanced Print Setup:

  https://helpx.Adobe.com/Acrobat/KB/quick-fix-print-PDF-image/_jcr_content/main-p ars/img_0.img.png/Print-as-image-screens...

• Photosmart 7520 black does not print after replacement

  Black ink that came in my 7520 missed today. I replaced it (with 564xl) but it stopped printing black completely. I went through the countless pages online, 'help' clean cartridges, etc., etc., etc. and have had no luck getting to print in black again. At this point, I burn money on color because of all the pages print diagnostic quality inks I printed.

  Anyone has any ideas to fix this? I've had this printer a few months. What a shame if it's already broken.

  Sorry about that, here's Bob tip for soaking the print head...

  1. Get a pan and put 1/2 "of very hot (not boiling) water in the bottom.
  2. Then, remove all ink cartridges, then remove the print head Assembly.
  3. Gently put the printhead nozzles down in water and soak for 5 minutes.
  4. Remove the print head and gently dry the electrical contacts.
  5. Put the print head in the printer and then reinstall the ink cartridges.

• OfficeJet 4636: print quality

  Hello!

  My printer will not print correctly. A self image explenatory (notice how the text is wiped out; also happens when you print plain text):

  

  What can I do? Thank you!

  In the paper here troubleshooting steps can help solve the black print is not correctly on your Officejet 4636.  According to your printing it seems that you have a defective black cartridge.

  If the first three steps of troubleshooting documents do not resolve the problem, you can try the cleaning cartridge manually as follows: take a cup of coffee and put 1 "very hot (not boiling) water in it.  Remove the black print on the printer cartridge and put nozzles in the water for about ten minutes.  After soaking, remove the cartridge and blot dry electrical contacts, and then reinstall the printer and run a cycle of cleaning, and then print a test page.

• New black cartridge prints partially and light

  Installed new cartridges, all 3 colors and black. The colors are perfect! Black does not print. When the spreadsheet the test of my own running he print selected areas and very light, but not the entire sheet. I cleaned the heads and did the test sheet and there is no black who came through

  I guess that the printer is out of warranty?

  If so, you could try to soak the printhead as described here Bob...

  http://h30434.www3.HP.com/T5/other-printing-questions/Photosmart-premium-C309a-black-prints-out-green-on-photo-paper/m-p/449245/highlight/true#M28673

  (1) get a pan and put 1/2 "of very hot (not boiling) water in the bottom.
  (2) remove all ink cartridges, then remove the print head Assembly.
  (3) gently put the printhead nozzles down in water and soak for 5 minutes.
  (4) remove the print head and gently dry the electrical contacts.
  (5) replace the print head in the printer and then reinstall the ink cartridges.

  BTW, you turn off the printer on the power button or simply unplug the wall?

  Do not print in black

  http://h30434.www3.HP.com/T5/Ink-toner-cartridge-printhead-issues/black-not-printing/m-p/2926025

• printer all-in-one psc2510 does not power on. Hourglass is displayed.

  Top of this printer (psc2510) has been partially open to allow the cleaning of the scanner glass. Since then printer will not complete the power on sequence.

  Thanks for your time to help resolve this issue.

  Jin

  Is that what this printer connected via a power protector? If so, try plugging directly into the wall electrical outlet.

  Tell me what's going on...

  

  Kiko

• Printer to skip every third line

  My Deskjet 2050j skip every third or fifth line based on the document that I print. I've tried all sorts of cleaning of the printer have options, I refilled the cartridge, tried printing in three different computers and still have the same problem. Then I tried to print a horizontal page with the same text, I had no problem, then tried to print a drawing in black and white, I did and it was no problem. I only get this problem when printing text in a page in a vertical way.
  
  Info:
  Model: Deskjet 2050 all-in-One J510a

  Firmwre version: SLM2FN1006BR

  the printer software version: 022.050.231.000
  driver version: 04.43.07.853

  This is due to a problem of electric contact between yout printer and cartridge
  Try cleaning the contacts of the cartridge with a lint free tissue. (A folded dollar bill works well).