ENVY 5530 e-all in one

Similar Questions

• ENVY 5530 e-all-in-One Series: My ENVY 5530 e-all-in-one prints only two pages of a multi-page document.

  My newly installed (Jan 2015) ENVY 5530 e-all-in-one prints only two pages of a document with several pages of my HP desk top 500-123ea, windows 8.1. Message on PC "Unable to print document", it's even on Double or single sided printing.  A ran Scan doctor, OK; reloaded software and Firmware from the Hp site. He spent hours and hours of reading the elements of list of support HP; Impossible to talk online with HP. very in angry and frustrated. This HP product seems not as "fit for purpose". I will give HP Feedback after this announcement and rate accordingly. I beleve others have similar experience of this problem. HP is aware?  Is anyone out there that can help?

  We gladly invite you.

  A Roll-up update is already available since December, although it seems that the description is not being updated accordingly.

  Follow the section "get the hotfix rollup for Windows 8.1"in my previous link, which can be obtained by installing the package or by using Windows Update, this is the update that the articale refers... ".

  Shlomi

• HP ENVY 5530 e-all-in-one: printer is not to connect to the Internet wireless

  Hello

  English is my second laungage. hope you understand...

  I can print with printer through windows and Mac PC cable. but, I can not connect between rutour and the wireless printer.

  I used the Setup Wizard and found the SSID name. I typed PW. but "Not connected" is displayed.

  I print the Configuration Page from HP network.

  Live wireless

  Status on

  What else can be done using wireless printer.

  Kind regards

  MI-Ko

  Hello

  If you try to connect your printer to the router, you should make sure that wireless Direct is trurned to offshore. Direct wireless is a feature that allows you to connect a device directly to your printer without router (the printer generates its own wifi)

  Please turn off direct wireless (it's often a button on the front panel) and try to connect again.

  I have included a link below for you rprinter support page that contains the user guides that should help also.

  http://support.HP.com/us-en/product/HP-envy-5530-e-all-in-one-printer-series/5304881/model/5304882

• HP Envy 5530 e-all-in-one: envy 5530 E cannot detect alignment page

  I'll put up a new e-all-in-one printer HP Envy 5530. I went through the installation OK, until I got to the part about the alignment of the print cartridges.  It prints the alignment page, it will copy even, so I know the scanner works. I printed several pages and they all look great.  But when I use the ink cartridge alignment tool it does not detect the alignment page in the scanner.

  Yes, it is face down on the scanner

  Yes, the cartridges are installed OK

  Yes, printing seems good

  Yes, the scanner can scan and print pages, even the alignment page

  What else to try?

  Thank you

  Well, too bad. I unplugged, moved the card to a regular wall outlet instead of a power strip, and it is turned on, ask to do a print alignment.

  I did, it printed the page, I put the page on the scanner and it completed the alignment.

  I don't know what the problem was earlier, but it worked this time.

• HP ProBook s 4430: hp envy 5530 e - all - in - one printer prints not after windows 10

  I got Win 10 installed for a few months and have just tried to print with my HP Envy 5530 e printer. I tried a doc in Word and he showed that he was priinting, but he vanished from the queue after about 15 seconds.

  -C' is my default printer and displays "series HP Envy 5530 (network).

  -my wifi is connected

  -J' tried to unplug machine and wall & turn off wifi

  -J' tried troubleshooting, but he could not identify a problem

  -J' tried to update.

  -J' uninstalled and reinstalled with disc and I have uninstalled and reinstalled online

  -Print and scan doctor = all OK

  -Test print = print and submitted, but disappears after seconds too

  -internal print has no print

  -disabled firewall only = no print.

  What Miss me? I've never had a problem with Win 7.

  Hi rb101,

  Your suggestion to contact our assistance worked!  I had a conversation with someone, and they changed my driver to a generic driver and that's...

  Thanks a lot for all your help

• HP Envy 5530 e-all-in-one: copy/scanning does not work

  All the functions of the printer/scanner worked before Windows upgrade Windows 7 10.  After 'upgrade' to win 10, scanner and copier functions are kaput.

  SYMPTOMS:

  Printer funtion still works

  * Copy funtion indicates "" Now"copy" but never active scanner.  Pressing Cancel does not stop the process.

  * Manual SHUT DOWN does not work with constant "Shutting Down" message.

  * Scan to the computer and scanning to E-mail functions do not work

  * Try to run Windows scan "does not recognize the HP profile" and cannot scan using Windows 10

  ACTIONS:

  * Initially received 'C4EBA230' message on the printer screen blue with flashing icons, but a hard reset solved error

  * Have completely uninstalled & reinstalled software base three or four times of HP and HP update disc once software has detected and installed

  * Ran HP, utility for troubleshooting several times before and after reinstalls for problems of scan - driver detected every time problem.   Ignore the results of audit of pilot and proceed to the verification of scan did not work

  * Performed four resets hard to return to the firmware with parameters.

  * Tried scanning HP and Capture app (Nope - message "Device is busy" - same device is not)

  * Voltage checked the cable power and the wall outlet (OK)

  * Checked ink levels (more than one half full)

  * Searched updates firmware (not available on HP support site for want 5530)

  Seems to me that it might be mutiple problems/possible solutions:

  Machine firmware problem?  n ' any means to reinstall the current firmware via a download?

  Mechanical scanner problem? -scanner engine bad/blown bulb? -where is the nearest HP Service Center authorized Texas?

  New driver development necessary to scan to computer compatibility with Windows 10? -C' you all of the problem

  Your diagnosis?

  Hi doktor,.

• HP ENVY 5530 e-all-in-one: HP ENVY 5530 e-all-in-one will print but not scan

  The material (both print & scan) worked well on OS 10.10.x but as soon as I xfr needed a MBP less 10.11.4 it stopped scanning through the HP software, but will work under Mac software scan. (The side of the printer still works fine.)

  Hi @Mrkil1o1,

  Welcome to the HP Forums! I'd love to help you to scan from your 5530 craving for your Mac. I understand from your description that it worked well when you have 10.10, but since the upgrade to 10.11 you can print but not scan.

  Let's start with resetting the printing system, uninstalling the software, repair the permissions of the drive and re - install & re-add the printer:

  Scrub / uninstall

• HP ENVY 5530 e-all-in-one: cancellation of registration - can I keep feeling with these cartridges?

  I'm about to cancel my subscription to instant ink I have don't print enough to justify maintaining the subscription (2 pages this month, 0 last month, you get the point). When I cancel, can I keep these cartridges and keep printing from them after the end of the billing cycle? Cartridges still have ink in there and I don't want to go out and buy new if I can continue to use these. You don't know exactly how it works.

  Hi @morgdod.

  Welcome to the Forums of HP's Support. I understand that you would like to know if you can use/keep the cartridges instant subscription after the cancellation of the instant the ink service. I would like to help.

  Instant HP ink cartridges do not work after the end of your current billing period, and you will have to go back to HP. To continue printing after the end of your billing cycle, make sure you have ink of standard replacement cartridges ready to the use of your printer.

  This link will have more information. Ink HP Instant - cancel your instant ink HP Service.

  Let me know if that answers your question. If it did, that's great! Give us some reinforcements by pressing buttons of solution and laurels, that we will help and others see that we have the answers!

• 8.1 Windows Pro update the problem (from Windows 8 Pro) on Envy 23 TouchSmart all-in-One...

  Hello

  I have a HP Envy 23 Touchsmart all-in-one that I bought a year ago (12/2012). It comes preinstalled with Windows 8.

  System information:

  (a) Intel (r) Core i7 - 3770 S CPU @ 3.10 GHz

  (b) 8192 MB of RAM

  A few weeks after that I had bought the system, I've upgraded to Windows 8 Pro with Media Center that I bought through Microsoft upgrade program.

  Last week (19/10/2013), I saw the option upgrade to Windows 8. 1 in the store and decided to upgrade.

  After a few minutes, I got a prompt asking me to restart the computer, and I did.

  However, I noticed that the screen has turned white, but it restarts not really - I have seen that the hard drive light was still flashing and I waited for about 15 minutes. I know it does not restart because if that were the case I would have seen the HP logo on the screen of the BIOS. A little later, the system entered into mode 'sleep' (at least the light blinked slowly as if it was the sleep). As it was late at night, I decided to leave the system alone and decided to check on it the next morning. The next morning, he was still in mode 'sleep' (as I feared) - when I tried to wake up from her sleep by moving the mouse/hit the return key, he did the exact sounds as if he were to wake up from its sleep (as it always does), but the screen is still blank. The light power button lit up constantly indicating he's awake now.

  At this point, I decided to turn off the system by holding the button for a few seconds. To restart, I saw the HP logo on the BIOS boot screen and the screen went white and nothing came.

  So I decided do a system recovery using my Windows 8 recovery CD and turn off the system with the CD in its niche. This time, the system came and began immediately to restore my OS to a previous version.

  After connecting to the system recovered, I received the following message:

  "Could not update for Windows 8.1.

  Sorry, we could not complete the update Windows 8.1. We have restored the previous version of Windows on this computer.

  0xC1900101 - 0 x 40019.

  I tried to reinstall Windows 8.1 a couple of times after that. Once to disable all non-Microsoft services and disabling all startup programs. Always the same result.

  I have no antivirus software on my other system protection of Microsoft default system software.

  Any help, greatly appreciated.

  Thank you.

  I have disabled active secure boot existing starter and the update worked.  Now we get the error of watermark "secure boot not configured correctly.  But I have re-enabled secure boot and the error disappeared.

• HP ENVY 7640 e All in One spring: printer - printing with locks on them paved preferences

  

  I'm looking for help with my HP ENVY 7640 e-all-in-one printer. I felt the single best face of disorder and I went to the printing preferences and I see there's pad locks on all parameters. So if I select a preference to change it, it does not change, I guess because the pad locks. I don't know how they got there or how to remove it Please HELP!

  Thanks in advance!

  @toni_j

  You could try the following:

  Create your own shortcut / model from the "locked" shortcuts, which are already available.

  See:

  Printing options

  See the Section titled: custom preferences print template

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• HP Envy 4500 printer all in one

  My Hp Envy 4500 printer all-in-one lights up not down IT. If I unplug the power cord, then plug it back it then the printer lights for about 14 seconds and then turns off.  Any ideas?

  Open the link: www.hp.com/contacthp/
  Enter your product number or select Auto detection
  Scroll up to "still need help? Fill out the form to select your contact options.
  Scroll down and click on: contact HP options - click Get phone number
  A file number and phone number will be displayed.

• HP Envy 7640 e-all-in-one Seri: HP Envy 7640 does not print

  Printer locked up - line said that the printer's paper (not) and it was offline (no). I unplugged, restarted the computer and the printer. Followed all the basic troubleshooting tips and stupidly the suggestion to reset all printers. Big mistake, now zero printers happen when I try to add. The search option does not either. Is it my computer? I don't think so. This is a NEW printer - printer only a dozen or so articles. Help, please!

  Welcome to the HP community @ellumare,

  I read on your desire 7640 does not although you receive an "Out of Paper" error, the printer showed as 'offline' and currently cannot add printer on your Mac with 10.7.

  Here's what I would recommend. Try troubleshooting the equipment first, because if there is a problem with the unit, this will lead to software problems and troubleshooting cycle can get tedious.

  1. power reset the printer and make sure the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on.

  Turn on the printer.
  With the printer, unplug the power cord at the back of the unit.
  Unplug the power cord from the wall outlet.
  Wait at least 15 seconds.
  Plug the power cord into the wall outlet.
  Reconnect the power cord to the back of the unit.
  If the printer does not by itself, press the Power button to turn it on.

  2. try to make a copy of the front of the printer. If the work of copies successfully, go to step 3, if the copies do not work, tell me what happens when you try to make them as there is most likely a hardware problem.

  3. from your Mac:

  1. Reset the printing system
  2. Repair disk permissions
  3. Restart the Mac.
  4. Click on this link to download and install the full features and software driver: HP ENVY 7640 e-all-in-One Printer series full feature software and drivers
  5. Print from text editing and other test applications and also try to scan from HP Scan/HP Utility.

  I hope this helps, and I hope to hear the result!

  Tip: Make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on.

• HP Envy 4500 e-all-in-one Seri: scanning multipe pages in a document file

  I'm trying to scan multiple pages in a document file. I am currently using Windows 10. What are the steps to do this successfully.

  Hello

  Thank you for using the forum.

  To use the Scan software on your printer, you will need to download and install the printer driver.

  We recommend that you download the full features and it can be found here:

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-4500-e-all-in-one-printer-series/5304875/model/5304876#Z7_3054ICK0K8UDA0AQC11TA930C7

  Once you have installed the software, you can click the icon for the printer on the desktop and it will bring up the HP Printer Wizard and you can use the Scan software.

  You will first need to scan more than one page, select "Save as PDF".

  Once you've scanned the first page, in order to scan several pages, you will need to click on 'Add page' (as shown)

  

  When you are finished, you can save the document.

  Here are several videos giving you good advice on digitization (printers in the videos are using the same software to Scan as your HP Envy 4500)

  Scanning multiple photos:

  HP Officejet Pro 8630

  https://goo.GL/ADYDmo

  Scanning tips:

  HP Officejet Pro 8630

  https://goo.GL/fjZvqM

  HP Deskjet 2540 scanning tips

  https://goo.GL/qfQyf4

  Hope that helps.

  Please click on the "Bravo Thumbs up" If this has helped you and 'Accept as solution' If this helped solved your problem.

• HP Envy 4500 e-all-in-one: 0XB0595DD2 error Code

  Hello

  Can anyone help identify this error code and a possible resolution? I plugged my printer yesterday and the 0XB0595DD2 error message came immediately. I turned the printer on and off a few times, but it happens every time (the printer was not connected to my laptop). My printer is the: HP Envy 4500 e-all-in-one, model no SD-GOB-1301.

  Thank you.

  Reference:

  http://h30434.www3.HP.com/T5/Ink-toner-cartridge-printhead-issues/do-you-have-an-ink-system-failure-0xC-error-message/TD-p/740567

• ENVY 7640 printer all-in-one: problem software printer after updating to Windows 10

  After updating Windows 10, my HP ENVY 7640 all-in-one printing software does not open.  A dialog box appears asking if I want to install a new program.  How can I get the software of the printer to open?

  Once you upgrade your computer to Windows 10, you upgrade your printer for Windows 10?

  Go here...

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-7600-e-all-in-one-printer-series/6617267/model/6617268

  Download and install the drivers and full software.