Error 1002 when about to reinstall Vista to new drive hard-pavilion dv9500

Hey there,

First of all, a bit of background:

The computer (HP Pavilion dv9500 17 ") is about 4-5 years. The warranty expired in 2010.
He was sent to HP before (about 2 1/2 years) within the warranty for a faulty NVIDIA card fried its motherboard and working perfectly, given that these parts have been replaced.
But lately, some of my files are missing and my computer starts on hibernate on its own and stops unexpectedly. About two weeks, the hard disk provided with the system (a WD 3200BEVT Scorpio Blue SATA 2.5) began to collide and click on erratic and has not, showing me the 'Operating System' not found error from the start. I have no reason to believe that this was due to anything other than a hard to die.
About three days ago I was able to start upward into the operating system, temporarily, in which I created a set of successful recovery discs using the Manager. The version of Windows in question is Vista Home Premium 64-bit. The machine is labeled as Windows 7 compatible.

I bought a hard drive from Amazon, a 5000BPVT WD Scorpio Blue SATA 2.5 and replaced the dead with her. In the BIOS, the hard drive does not read for errors when pass the diagnostic test. However, when you run System Recovery Manager, I came across the error 1002 when it is on the third and final drive and getting ready to write to the hard disk.

Now, when I try to retry it, the computer starts and after the F - key option screen it is just blank with a flashing cursor.

From what I've been able to find on the site to other situations similar to mine, I seem to have several possibilities as to why it went wrong.

Either my recovery disks are bad because the hard disk on which the recovery partition was conducting at the time of their creation was bad,
The recovery discs were bad anyway because the recovery on the partition information has expired long ago,
My new hard drive isn't called a DMI utility that is in conflict with its compatibility with my machine, although it is otherwise compatible.
Or maybe my computer is old and fecacked and there is nothing that can be done.

As previously mentioned, I'm no longer under warranty. I've already spent money that I don't have on the new hard drive and now I'm worrying that it was for nothing. I'm just curious if anyone, having heard my specific situation, can determine the question so I can get my class there. If it's a question of having to order a new recovery discs, I think I can handle this. Indeed, if a clean install of Windows would do, my friend has offered me his extra copy of Windows 7 because it turned out she didn't need her.

But if it is this exclusive utility, well, I can't afford the cost for sending to be tattooed out of warranty, and at that time, the question is whether it's just better put into place for a new machine. Which is a shame because I was really hoping it would last me at least until I have been done with the junior school. As you can imagine, not having no not my computer heavily paralyzed my ability to handle the six classes and work part-time in the heat of the season of final exams.

Any help on this would be greatly appreciated.

Model hard drive is a drive of 'Advanced' Format, you must return it and buying a hard drive that is not the type of advanced format, then recovery should complete without error.

http://www.wdc.com/global/products/features/?ID=7&language=1

HP recovery disks do not work with the AF disks, recovery fails at the step where he created additional partitions for hp_tools and recovery of partitions because it does not include the hard drives of AF, so he is unable to create or write to these partitions.

Tags: Notebooks

Similar Questions

Compaq Presario CQ71 - error 1002 when using recovery (windows Vista)

Hi guys,.

I just encountered error 1002 while using the recovery... Recovery successfully crossed reformattng my drive, but crashed before reinstaling the original content. It's okay if I'm trying to hard drive or dvd rom recovery, all this translates into error 1002. I did some research and it seems that it is a very common error in hp without adequate solution products. I think I'm out of luck because my warranty expired years ago... How can I solve this problem? For me, it seems that recovery content originally placed on my hard drive (and later burned on the DVD by me) had been damaged. I see 2 possible solutions here:

-to order an another recovery of the drives together (although I saw a few reviews it did not)

-buy the new "Windows" and install a new fresh install (I will be able to perform the new installation at all?)

I'd really appreciate pointers as I really don't want to lose my money for a solution that would work!

Kind regards

Robert

Hello

You can call the MSFT customer service and they will generally be able to find it for you.

http://answerdesk.microsoftstore.com/msusa/en-us/answerdesk/answertech

Error 0x800704b3 when you try to map a network drive

Hello

I have the following error message when you try to map a network drive in my home network:
"\\iomegahmd cannot be reached" and the error code is 0x800704b3.

I already looked in the services, and my strong assumption is that the problem is that 'TCP/IP NetBIOS Assistance' service is not statrted and it is disabled. When I try to start it, there is an error message:
"The system could not find the specified path".

I also checked the dependency of the 'TCP/IP NetBIOS Assistance' service components:
Auxiliary function for Winsock driver
NetBT
TCP/IP protocol driver
NetIO-legacy-TDI Support driver
in the Device Manager is running, but they are all running. Startup is set to 'system '.

Under the properties of version 4 of TCP/IP Internet of the wireless device, under Advanced-> WINS I ve put enable NetBIOS over TCP/IP, but it helps t is not either.

What else could try, so that I can map network drives?

I should also mention, that the problem persists for a few weeks. Before, it was working properly. In addition, on other computers on my network I don't have access to the same network drive problem.

Thanks in advance,
Tithe

> I should also mention that the problem persists for a few weeks. Before, it was working properly.

It of difficult to say what's wrong in your case. My first idea is: put installation beginning point of time before this error appeared.

I recommend also to disable all security software and check if you experience the same problem.
If you still experience the problem, then follow the link to fix the damaged user profile.
http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

Blue screen error: 0x0000001a when using system to restore with new hard drive disk

original title: blue screen error when you use the system disk to restore with new hard drive

I bought a new hard drive to my computer because the old one gave me a bunch of error messages on screen blues. I installed in the tower and tried to use my restore and system recovery disks that the manufacturer has given me, the process has got to the last disk then asked for the system once again restore disc, and then began to load the last steps and went to blue screen error. I don't know what to do, I mean it's a whole new drive hard, so where could the error come, theres nothing on the hard drive because I have not yet used really, yet. Help, please

I have finally fixed the problem myself. The problem was that one of the sticks three memory was bad and the only way I could test this error. I took two sticks a left, used disks I had and was able to restore my computer, then I put a stick, turned on the computer, had no errors so I let him, so I put the last stick in and com immediately on, I had the Disconnections: memory management and that's when I knew that the last stick of memory was bad I took it back and now my computer works well and I can't buy more memory for not too. So if someone gets this BOSD error on memory, I'd say 8/10 computers have bad memory (not a number). If youcannot run the tool of diagnosis of memory like me then I would suggest to do what I did with the trial and error, it was the only way to understand the problem. Thanks for your help

Need to reinstall Vista after replacing the hard drive

Microsoft website has confused me! Help please! Should I just buy and install vista again?

* original title - I got my computer fixed and a new drive hard put, I could not find the disks from acer with what he came or the vista disk. Acer disks I found, but how do I buy windows vista? *

Microsoft website has confused me! Help please! Should I just buy and install vista again?

Hey LauraR1991

If you have your acer recovery disks, you need not buy new vista

you already have a license of vista

The acer recovery disks are to reinstall vista on how you purchased your computer

If the disks from acer that you aren't below recovery disks link is to buy vista directly at acer recovery disks

they sell them at a nominal cost

Acer Recovery Media purchase program

https://secure.TX.Acer.com/rcdb/main.aspx?brand=Acer

Walter, the time zone traveller

New drive HARD & OS errors-> HP 8000 Elite Small Form Factor PC

New drive HARD & OS errors---> HP 8000 Elite Small Form Factor PC

Can not install Win XP on another hard drive

I work with a...
HP Compaq 8000 Elite Small Form Factor PC

Original SATA HDD is loaded with Windows 7 Pro.

In order to install a program using this PC as a digital video recorder
I installed the video capture PCI card and related software. I had problems
associated with software and Windows 7.

I know that the software works with Windows XP.
Do not want to remove the original HDD, I tried my win7
to replace the HARD drive and do a clean install of XP.

I get the same error during the installation of the OS. I tried different
SATA and different XP install disks.

The error I get is shown in this photo.

Original HP HARD drive is a Hitachi 160 GB

I tried 2 known to be good SATA drives.
Seagate 500GB
WD 80 GB

I checked the bios settings and even revenue tio rear BIOS
default settings.

I get this error even with everything I tried to do.

This happens during the OS install just after or during the process of the installation of temporary files are current

written to the HD.

When I re - install the original HD loaded with Win7, everything works as it
expected.

Any ideas on what] s going on here?

Hello:

The problem is that you must incorporate the necessary sata ahci drivers for windows XP to see the hard drive.

Has Windows 7 and XP is too old an operating system to make them.

Read the info at the link below, section of Intel and then read the downloadable PDF document for instructions on how to integrate all the drivers.

http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/m-p/114120#M17758

The only other way to install XP on this model is to go into the bios, the storage section and change the setting of sata ahci to ide emulation, save the setting here and once again, when you go out.

The problem is that if you do this, you cannot change the setting for the preferred setting of DCIS, unless you know how to install the correct ahci sata driver after installing XP from the controller. If you try to just change the setting back on ahci without having to install the controller driver, the PC does not start upward.

Try "slipstreaming" the drivers first and if you can't swing, install XP in IDE mode and I'll help you get the drivers installed, so you can change the BIOS to ahci setting.

I have vista 32-bit, he sees not my new drive hard hitachi, in device manager it shows that it works correctly?

Why my expoler does not see my new drive hard when it is in the device as o.k. Manager.

Look for the drive in computer management, it may need to assign a drive letter.

Change, add, or remove a drive letter
http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter

Get an IRQL error when reinstalling Vista on a formatted HARD drive.

My (HP a1700n) office has been very slow, perhaps a virus. I ran Norton NIS and also had Norton disk utilities cleaner. Before that the Office stopped completely, I was able to shoot the important things (pictures, videos, etc) nothing else I could lose and wasted. I decided to start over and reinstall the Vista operating system, since I don't have the disk. Has gone so far as to choose the partition and after that he began to «analyze...» "it froze and gave me some kind of error that the partition not could not be found or something like that, well I deleted the partition with the recovery partition since I created a disc a new partition using all the available space, but now I get the not_les_than_ error message. I only go as far as to choose the partion and starts to analyze then the BSOD appears. I did not add anything other than a 1 GB of ram and I removed it, so now the computer only has the 1 GB it is came with, everything else is what came with when I bought it 2 years ago. I don't know if it's hardware related or I'm doing something wrong.

Any help would be greatly appreciated.

Eric

If you get BSOD when installing, try the Vista repair Forum for advice and give them all the details of BSOD error.

http://social.answers.Microsoft.com/forums/en-us/vistarepair/threads

See you soon.

Mick Murphy - Microsoft partner

Error 1002 when installing the desktop creative cloud application

I too am a very frustrated Adobe user. I use a Macbook Pro with 10.10.5 as the operating system.
My problem is the same that many other people, I am unable to upgrade Creative Cloud Desktop to the 3.8.0310 version and still get error 1002 to the 2% mark. I have tried virtually all the "stuff" in the book, those recommended by Adobe and those blogs, and nothing works. I have even directly connected to my internet provider, without going through my wi - fi modem and using their connection broadband.
Up to what Adobe ceased to provide Direct download links, I was able to update my software. My problem has always been that Creative Cloud Desktop will put not to date to the next version, and what happened on my first Mac as well. If Adobe wants to stop direct links, so why can he not at least make sure that the application works 100% of the time for 100% of its loyal customers. You are deflected us Adobe with your policies, especially now that many people use other software that may not be as powerful as Adobe programs, but at least they are reliable.
Bob C.

Pleiades_k that you have received error messages when you perform the steps mentioned above? He was facing difficulties to locate the OOBE folder?

I would recommend that you run the utility for uninstalling desktop available creative cloud application during the uninstall of the desktop Adobe Creative cloud application , and then try to reinstall the updated version.

If you continue to experience difficulties, please contact our team of support directly in Contact with the customer.

0x80000FFFF error code when you install Windows Vista SP1.

Original title: I had a problem with service pack 1 on vista 32 bit [allways should I install

I had a problem with service pack 1 on vista 32 bit [allways should I install on the window update

Try this Fixit MS

0x80000FFFF error code when you download updates on a computer running Windows Vista by using Windows Update or Microsoft Update

http://support.Microsoft.com/kb/946414#letmefixit

1935 error message when you try to install the device driver for the wireless broadband

need help addressing an error message when you install a device wide band. Error 1935

Hello

1. have you done any book to the computer before this problem?
2. What is the exact error message of th?
3. What is the brand and model of the computer?

Method 1:

I suggest you perform the steps in the section "" method 1: repair the installation of .NET Framework 4' and ' method 4: repair the .NET Framework "in the following article." You can ignore the title of the article.

http://support.Microsoft.com/kb/2507641

Method 2:
Unregister and re-register Windows Installer
Unregister and re-register Windows install to fix the Error 1935 in Windows. Follow the steps below to reregister Windows Installer.
a. Click Start, click all programs, and click Accessories.
b. right click on command prompt and run as Admin
c. type following commands
msiexec /unreg
msiexec/regserver
d. Exit at the command prompt

Method 3:
Run the System File Checker
How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
http://support.Microsoft.com/kb/929833

Method 4:
Run Disk Cleanup.
http://Windows.Microsoft.com/en-us/Windows-Vista/start-disk-cleanup

C:\\Windows\system32\ksproxy.AX error message when you try to use a new webcam with Skype

I have a new webcam which is recognized by my computer but displays always the followed error message...

.. If the other is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator for the Publisher of software for support.

I tried to uninstall and reinstall the webcam and Skype and insured Windows is fully updated. I tried using the disk for the installation of the software and drivers downloadable from the Web site. It's not to do with the firewall with my antiviral product, as I have tested that turn off too. What can I do to get my 'Easy Webcam' SPC230NC Philips to work then?

Thank you.

Hello

1. are you able to use this webcam on other applications?

Method 1.
I recommend you download and install the PC software and the drivers from the following site.
http://www.P4C.Philips.com/cgi-bin/dcbint/cpindex.pl?CTN=SPC230NC/27&SLG=en&scy=us&mid=Link_Software

For more information see the articles below:

Updated a hardware driver that is not working properly
http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

Tips for solving common driver problems
http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

For additional help, you can also check with the technical support of Philips.
http://www.support.Philips.com/support/sms_page.jsp?userCountry=us&userLanguage=en

Method 2.
If you suspect an activity of virus that I highly recommend to run a Virus Scan online.

Sometimes the security program installed might not be fair enough. I also recommend you update your security software regularly.

a. follow the link below to start the free online scan:
http://OneCare.live.com/site/en-us/default.htm

b. run the malware removal tool from Microsoft.
Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

Microsoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

I hope this helps.

Thank you, and in what concerns:
Shekhar S - Microsoft technical support.

Visit our Microsoft answers feedback Forum and let us know what you think.
If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

I am trying to reinstall Windows Vista from my drive hard can u help me__

I need some help tryin to reinstall windows vista from my hard drive, I went on the recovery program who was here and burned a cd, but none of the programs on my computer it open so I need to know how to reinstall it from my disk hard please

You normally have to boot from the recovery disc:

Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to perform a recovery of the recovery hard disk Partition.

Normally, you have to press F10 or F11 at startup to start the recovery process...

Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

For any questions/problems about the recovery process, you will need to contact the manufacturer of the computer.

It is their software/recovery process, not Microsoft.

See you soon. Mick Murphy - Microsoft partner

error ikernelexe when you try to install the multimedia driver

When you try to install the multimedia driver, I get the following message: "error installing ikernelexe. Using Windows XP. Please notify.
Thank you

Hi MarkPfeffer,

This problem may occur if one or more of the following files are missing from the Windows\System32 folder:
- Stdole32.tlb
- Stdole2.tlb
- Stdole.tlb
Follow the steps listed in the article given to solve this problem:

Error in Ikernel.exe when you install programs using InstallShield

Reinstall Vista clean after replacing hard drive

Hard drive crashed in my Acer Aspire 3680-2682. I replaced the hard drive with a larger HARD drive and did a clean reinstall of Vista Basic to my CD anytime upgrade. My computer did not come with recovery discs and the recovery partition of course disappeared as well.

Can I use my same product key that is on my COST base sticker of Vista?

If you want to reinstall Vista to how you purchased the computer, use the ORIGINAL product key that was on the computer to do.

It was what was my original advice.

Mick Murphy - Microsoft partner

Error 1002 when about to reinstall Vista to new drive hard-pavilion dv9500

Similar Questions

Maybe you are looking for