Error-301034 with Toolkit ECU Measurement and Calibration

Similar Questions

• Toolkit ECU Measurement and Calibration does not run when I build an executable.

  I did a LabVIEW application that communicates with a target using CCP (with ECU Measurement and Calibration Toolkit).

  The source code of LabVIEW works OK, but when I create a .exe file, it does not work.

  I tried to copy the Toolkit ECU Measurement and Calibration dll:s in the same folder as the .exe file, but I still get error messages.

  What should I do to get the run .exe file?

  Do you have you created an "Installer" and installed on the laptop?

  If yes have you selected this Toolkit (ECU Measurement and Calibration Toolkit) to add to the installer when creating the same thing?

  Just try this approach once...

• Calibration Toolkit with 3rd party ECU measurement and CAN interface

  I would use the NI ECU Measurement and Calibration Toolkit with an NI CAN interface.  The interface devices supporting J2534 are very common.  The NI ECU Meas and Cal Toolkit allow this? If so, how does one time on another interface CAN interface to the Toolbox?

  The NI ECU Measurement and Calibration Toolkit National Instruments Hardware only supports.

  If you want to discuss the possibility of using any 3rd party hardware, please contact your representative local.

• Error message with program battery bluetooth and tecra 9100 XP SP2

  When I try to start program battery bluetooth the following error message appears:
  the instruction at "0x1000bf18" uses the address "0x0015d000". memory don't pet not be "read".

  Is someone can tell me, what kind of question is this and how to fix it?

  Thank you very much in advance

  Hi Patrick,

  For the benefit of other users of the forum please let me translate your error message: -.

  ""The Instruction at "0x1000bf18" uses the memory address"0x0015d000". Cannot read memory.

  This indicates that the broadcast program has stored the second addresses two memory as a place in which it writes data and now cannot read the data at this location memory.

  It may be because some other routine wrote too much memory or reported to this place as "in use".

  Windows will normally prevent such a situation from occurring, but being Microsoft is not infallible and errors may occur from time to time.

  If you get this message every time that you start your battery Bluetooth, it is more likely to be a problem with the Bluetooth program badly to access its memory cache, so I recommend reinstalling the Bluetooth program.

  Good luck

  HTH

  Post edited by: NickyNoogle

• Error-1074118625 with the PXI-4071 and PXI-2527

  When you use the LabVIEW and PXI-4071 PXI-2527 IVI drivers, I get a 1074118625 error in TestStand.  The sequence that initializes the MUX, init DMM, connects the MUX, expected debounce, and then to the DMM reading, I get this error.

  Error: niDMM .viExplanation of waveform (waveform data) reading is not found for the requested status code.

  Check that the required status code is correct.

  [Error code: error code defined by the user of 1074118625.]

  This sequence of events is used successfully several times elsewhere in the TestStand.  This error does not appear in any section of the knowledge base, or any help.  Any explanation would be greatly appreciated.

  I found this with google that seems like it could apply:

  http://digital.NI.com/public.nsf/allkb/A593DEBFD86A69C68625727900748EEC

• When itunes installation receive error message with 'install windows package' and 'procedure requires a rise. "

  Original title: Windows Installer Package

  When you try to install itunes, I get a pop up box that says: there is an error with the windows package install and it will not continue with the download.  I went online to download the package to install to my computer (Windows Vista) and when it starts to download get an error stating that "the procedure requires a rise." What it means?  I assume this has something to do with security in the administrative account that I am signed on the label on when problems occur.  Thank you!

  Hello
  1 did you change on your computer before this problem?
  2 - is a problem only with itunes?
  Follow the suggestions and check if that helps.
  Method 1
  a.Right click the download file.
  b.Select run as administrator.
  
  Method 2
  You can follow the procedure in the article.
  Problems installing and uninstalling programs on Windows computers
  http://support.Microsoft.com/kb/2438651#reso2
  See also:
  Problem installing iTunes or QuickTime for Windows
  http://support.Apple.com/kb/ht1926

• Help! Export error 27 with only a few videos

  I exported Final Cut Pro X projects directly on my external hard drive. I got an error 27 with one of them, and given that it is exported well I don't think it's a problem with my external hard drive formatting. All the videos have been imported in the same way and the same camera. Any ideas about why this is happening? Thank you!

  Most likely, you export a FAT32 / 'Windows' formatted the disk, right?

  error27 occurs when you attempt to save a file > 4 GB - that is not supported by fat32 (very old format..)

  So, small export projects, larger not. -.

  reformat the drive (erases all content!) to exFat or hfs + / "Mac"...

• Photosmart 5520: Scan to email: server connection error 403 (with app and scan)

  I scanned to send several times than I can count, but a few days ago, I get nothing other than the error "connection server 403 error." I checked the forums and someone said to go into apps and download the application. It did not work. I rebooted and tried everything, which he expects. Yet, nothing. Is this error to do with something outside as the real servers HPs - or is this something internal that I can fix it? I went as far as I can without resetting to factory settings (which I am fearful because I recently had the country code has changed on this issue and do not want to return to the country of origin), someone has any suggestions other than what I've sifted through the forums already?

  Hey @fruitfly20,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I understand that you have some problems with the scan to E-mail on your Photosmart 5520. I can help with that.

  We can try I couldn't see you is to remove and enable web services. To do:

  1. On the printer, click web services icon that looks like a tablet with a phone beside her.
  2. Click settings.
  3. Click on delete Web Services.
  4. Click again on the Web Services.
  5. Click on accept and Yes.
  6. Try scanning to Email.

  I would like to know if it works. If it does please not then let me know and we can try something else. Even if it solves your problems, so please let other users of the forum know clicking on accept as Solution below my post.

  I hope this helps and I hope you have a nice day!

• Measurement of angular position with encoder in quadrature and NI USB 6281

  Hello.I have an application developed with labVIEW 7.1 and 6014 OR for the measurement of angular position using encoder quadrature, where are used 3 sons - one of them connected to the source, second to the OID (0 or 1) and a third to digital ground. I can't use the same application or NI USB 6281.Now connections, I would like to know how I can create a similar application in labview 2009 and how to make the relevant connections for NI USB-6281, which is a mx NI DAQ device. Please suggest. Thank you.

  I have my loan application. I understand there are big difference using LabVIEW 2009 and NI USB card, compared to the previous version I was using THE LabVIEW 7.1 and a traditional daq. The difference, I should say that wellness is both in terms of simplification of code and the accuracy of the result. I was a little surprised, showing results. Thanks a lot to JB for your time and sharing those pieces of details.

  I can well after awhile my code in the forum. Hope this helps someone like me looking for a similar application.

• Error running on the SIMS 2 and need for Speed Carbon with WIN7 Ultimate 32 bit

  
  

  • Error running with the SIMS 2
  • The error that says: the DVD error running is not found
  • I tried to fix it: with XP SP3, VISTA SP2 compatibility mode (I installed the game and I want to play with the compatibility mode for XP with Vista, now I installed WIN7Ultimate 32bits and it doesn't work
  • I already downloaded the latest patch and still work does not correctly...
  With the CNSA, I have the same problem, it starts, but when loads of information to start playing, it opens a window saying the program cannot continue to run, restart the application and the ini.

  Hi fedelovrin,

  Do you have any error message during the installation of the game?
  Is that your DVD player plays all DVDs correctly?
  Could you give us the exact error message that you meet?
  Is the same error message on Need For Speed Carbon?
   
  Since this game is compatible with windows 7, it should work properly without compatibility mode.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?type=software&s=Sims%202
   
  Like you said you used the Windows XP on Windows Vista compatibility mode. Try to use under Windows 7 XP mode also and check.
  You can find more information on compatibility modes in the articles below:
  http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
  http://Windows.Microsoft.com/en-us/Windows7/Program-Compatibility-Assistant-frequently-asked-questions
   
  Here is the link for the support of the SIMS 2:
  http://TheSims2.EA.com/help/index.php
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• NOR-DAQ traditional (old) devices of measurement and automation explore 4.7 with LabView2010 under Windows 7.

  In measurement and Automation Explorer 4.7, with LabView2010 in Windows 7, peripheral OR-DAQ traditional (old) appears under devices and Interfaces and it allows me to create a chassis SCXI-1000, and she agrees "Reset for NOR-traditional DAQ.  However, it does not search the modules in the SCXI1000, and when I ask 'trial', he says 'Impossible to test the chassis at this time.'  The entrance of NOR-DAQmx devices for the SCXI-1000 chassis has no problem and detects the modules very well.  I need the Legacy DAQ to a popular former teaching tool that has no equivalent in NOR-DAQmx.

  Unfortunately, NEITHER-DQA traditional (old) for Windows Vista and 7 functions of the only driver on Windows 7 32-bit, as seen on the page of the driver at the end of paragraph 1 Solution. I recommend you move your program to DAQmx.

• I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe.

  original title: error with ehshell.exe

  I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe. Could you help me?

  This problem exists since the 1st Media Center. SP2 and SP3 had a difficulty, but it is obvious that it doesn't always. The same problem still exists in Vista today with a lot of other carried over from XP. System restore would work, but you do not have any good restore points so reinstall an operating system seems to be your only option.

  You probably don't want to do an OS reinstall you need for Media Center, but since it does not at all, you might want to play then remove the Media Center updates and or SP3 and reinstall them.

• Error: 0X0800C0133 with Outlook Express and cannot receive e-mail

  An unknown error has occurred with my Outlook Express and I can't receive emails. It is erroe 0X0800C0133. Please I need help on how to remove it and fix my Email

  It would be useful also (in terms of it being assistance), if you can insert your message standard on this subject as it goes in detail on the issue, than my comment and the topic of the thread inside error number, many perhaps find via search.

  Thank you

  Steve

• Problem with Quicken 2012 House and the company after installation, runtime error

  I have a problem with my Quicken home and business 2012. I upgraded from 2009 to 2012 and was able to use the new version for about 1 hour, but he hung a little.  Now when I tent to access my Quicken program, I get a runtime error "program: C:\Program Files\Quicken\qw.exe ' abnormal program termination. Quicken is then stopped immediately.  I am currently running Windows XP service pack 3.  Any suggestions?

  Hi RENEE HETTERLY,.

  I suggest that you uninstall and reinstall Quicken program on the computer, check to see if it helps.

  How to change or remove a program in Windows XP

  http://support.Microsoft.com/kb/307895

  If the previous step fails, then you will need to contact Quicken support for assistance.

  http://Quicken.Intuit.com/support/Windows.jsp

• Critical errors dealing with MRT.exe and error messages "Services and controller app has stopped working".

  I get two error codes... "Services and controller app has stopped working" and "Windows has encountered a critical problem and will restart in a min. Please save your work." The only time where it does it but when I plug my cable network. Already ran sfc and found nothing. Ran malwarebytes and removed a lot of viruses, I picked up, but I think that something in my registry can be screwed up after trying to remove the said virus. I was getting some kind of error MRT.exe and I tired looking for things to the top on this but I think I can have messed up a registry that was loaded entry of this and it has damaged something.

  Someone at - it answers that do not involve me having to reformat and install a new OS. I bought the computer off of a friend and it's a custom-made computer, so I don't have Vista Disc... while hoping a good solution.

  Help me please! :)

  Thank you
  Bishop

  In addition to using an anti-virus, as Malware/spyware scan:

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight...

  How to use Malwarebytes once it is installed and updated:

  1. open Malwarebytes > click the update tab at the top > get the latest updates.

  2. on the Scanner tab, make sure that thePerform full scan option is selected and then click on theScan button to start scanning your computer

  3 MBAM will now start to scan your computer for malware. This process can take some time.

  4. when the scan is complete, a message box will appear

  5. you must click on the OK button to close the message box and continue the process of Malwareremoval.

  6. you will now be at the main scanner screen. At this point, you must click on the button toview the result .

  7. a screen showing all of the malware displayed the program that is

  8. you must now click remove selection button to remove all the listed malware. MBAM will now delete all of the files and registry keys and add them to the programs quarantine. When you remove files, MBAM may require a restart in order to eliminate some of them. If it displays a message stating that it needs to restart, please let him do. Once your computer has rebooted, and logged in, please continue with the remaining steps.

  9. when MBAM has finished remove the malware, it will open the scan log and display it in Notepad. See the log as desired, and then close the Notepad window.

  10. you can now exit the MBAM program.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If you do not have a DVD of Microsoft Vista, borrow one from a friend.

  Read this tutorial on how to do a repair installation:

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  Regarding the relocation:

  You can borrow a suitable Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > find the latest Vista drivers for it > download/install the

  See you soon.

  Mick Murphy - Microsoft partner