Error "connection of the USB device was unsuccessful.

Similar Questions

• Error "one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." when you connect Logitech M225

  Original title:

  My wireless mouse works fine for the last 2 months, now, all of a sudden it doesn't work at all.

  I get a windows notification that says-

  "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it."

  I have Vista 32 bit OS on my laptop.

  My office has Windows 7 32 bit and I am able to use the mouse on this computer, then the M225 is not defective.

  I tried to look for a download of update on the site of Logitech & only found:

  6.32.20 set - point it did nothing to help.

  I also tried to move the receiver to the other 2 ports USB w / still the same results.

  Are there other downloads or solutions that will help w / this problem?

  You can also try searching for devices strangers (with yellow symbols) in the Manager under the mouse devices and other pointing devices and other devices (if any). Right click and uninstall unknown devices. Then restart.

  Also try the steps below to reset the power of USB:
  (a) the laptop off, unplugged from the wall outlet.
  (b) remove the battery for a few minutes, then reinstall it.
  (c) then restart the laptop.

• Error - "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  Original title: USB device not recognized / dysfunction

  "Unrecognized USB device".
  One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. Help for this problem, click this message. »

  This is what I get AFTER that I had to reinstall windows XP because a virus has attacked my computer a little before avg and Microsoft security essentials picked it up and destroyed... I have reinstalled twice... then I changed discs since I have two... well, I get this message from my 2 external Seagate Freeagent and my Phillips mp3 go gear aria... player these devices work on the laptop from my friend and she is under vista. It seems that since then they have worked on my computer before they would always run. My mouse and my cam work fine and my Canon printer gets thus detected... a few readers who have the space that is made... Ive looked everywhere for a solution... even upgraded windows media 11 and is player went to service pack 3. restarted several times... tried dPower Management tab and tried to

  Open recognition of the USB device by using Device Manager.

  .. I am at a loss: P please help thanks!

  isable the power management of the USB hub and I couldn't find the

  Hi LadyDefi,

  You can try to uninstall and reinstall the USB controllers and check:

  To remove and reinstall all USB controllers, follow these steps:

  a. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  b. click on the Hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and test to make sure that the problem is solved

  For more information, see the following article:

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error: One of the USB devices attached to this system has malfunctioned, and windows does not recognize it.

  tried already everything written here. When I plug my USB device (3 of them) my Windows a sad of the USB devices attached to this system has malfunctioned, and windows does not recognize it. I tried plugging it into another winXP machine, it won't work. Can you help me?

  Original title: usb malfunction

  His salvation,

  Thanks for posting your query in Microsoft Community Forum.

  1. What are the troubleshooting steps you have tried so far?
  2. If it works much earlier? If so, did you do changes on the computer before this problem?
  3. What type of USB device you are using?

  As you mentioned that the USB device does not work when plugged into a WinXP machine, it may be a problem with the device itself. In addition, the question may also arise if the currently loaded USB driver has become unstable or damaged or if your PC requires an update for problems that could conflict with a device USB and Windows.

  Therefore, I suggest you try the following methods (skip the ones that you already tried) and check if the problem persists.

  Method 1:

  Please try the fixit (s) provided below which will help you solve common problems associated with devices and USB ports.

  • Hardware devices do not work or are not detected in Windows
  • Diagnose and automatically fix the Windows USB problems

  If method 1 does not work, try Method 2.

  Method 2:

  Remove and reinstall all USB controllers.

  1. Open Manager devices by clicking the Start button, click Control Panel, click system and security, and then, under System, clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. In the list of the categories of equipment, locate and expand Bus USB controllers.
  3. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.
  4. Restart the computer and let the USB controllers get reinstalled.
  5. Plug in the removable USB device and test to make sure that the problem is solved.

  If the problem persists, go to method 3.

  Method 3:

  This method will install the latest drivers from device to your USB device.

  1. Click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.
  2. Click find updates. When the scan finished, click optional review updates.
  3. Click the check box next to the update, and then click install updates.
  4. If you are prompted, read the license agreement, then click I agree.
  5. Follow the instructions on the screen to download and install updates.
  6. If you are prompted, restart your computer.

  More information: Update a hardware driver that is not working properly

  If the device fails after updating the driver, you can try to roll back the driver with its previous version.

  Restore a driver with its previous version

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Lose the connection to the USB device

  Hi all

  I have developed an automated system that serves to calibarate lines scales. These scales are usually between 10mm and 150mm long and 0.1 mm and lower divisions. I use a camera to determine the edge/position of the divisions. A step of translating Physik Instrumente (USB) and a motor piezo high-resolution from each division. A laser Interferometer is used to measure the distance, the engines are passed (i.e. the distance between the divisions).

  In the program, I have the ability for the user to define a start time for the calibration, for example 02:00.

  My problem is from 02:00 in the morning, the computer is spent in screen/power saver mode. This leads to the stage of translation of Physik Instrumente to disconnect and causes an error that interrupts the program. In the morning, when I come back, the error is on the screen and when I press on continue the program continues as usual.

  So what I'm looking for is a way to remedy this situation. I tried without success to the following:

  Disable the screen/Power Saver - The IT Dept here mode won't let me not because several users have access to this program, they have to disable for each user.

  Disabling the power management in the usb port properties had no effect.

  I also tried a Subvi who would hover over a position on the screen in the hope that this would stop the computer into energy saving mode. Needless to say, it did not work.

  Any ideas would be appreciated,

  Thank you very much

  Cain

  elrathia wrote:

  You may also look here;

  (right click on the root USB at the bottom hubs to get the properties box)

  This is one of the first things I turn off with any machine that I meet.  Causes more problems than its worth.

  But it seems that your problem is in the machine, just go to sleep after a period of inactivity rather than the power management of lower level.

• C309a error message: remove the USB from the printer device

  My C309A was connected wireless via time capsule or Airport extreme for a year to the network & work find on all Macs. There was an update of the HP software to 2.4.1 on 01/07/10 and since then it won't work. I have reset to default settings, more #/ 3 reboot and it goes through the initialization process but the network configuration wizard cannot find the wireless network and the same error message finally backup on the screen and you can't do anything unless you turn off. He can come back and do not have an error code next time, but it will not find the network either... so you can shut off again and the next time the error message appears. There has never been whatever it is connected to the USB port. I have re - installed software and still have the same problem.

  Please need help or suggestions. Thanks in advance.

  E-mail: [text removed for privacy]

  Here is how to contact HP.

  Please remove the serial number of your post (Options > Edit Post).

• HP photosmart c309a error message States to remove the usb device because it is not compatible

  no previous problems with printing far... error message States to remove the usb device because it is not compatible with the hp photosmart wireless photosmart c309a c309a printer.the only thing plugged into the printer is power cord... no usb device is or was plugged so I do not understand this error message. I unplugged everything and reset the printer but the printer status is offline with the same error message.

  Jorup, try to run this utility and it must diagnose the State of the printer:

  http://goo.GL/u3jDE

  Also, when you unplug the printer, remove the power cord to the back of the unit and the wall for thirty seconds, then reconnect it.

  I would like to know how it goes!

• Windows 7 and install/recognize the problems of printer HP LaserJet P2015 error - USB Device not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  Title: Windows 7 and install/recognize printer HP LaserJet P2015 teething problems...

  I have a dell inspiron that was originally windows Vista and I changed to windows7.  I have a LaserJet where I work, a HP LaserJet P2015 printer and when I plug in the USB, it says (peripheral USB not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  How and what should I do to get the printer going or to get the computer to recognize.  Installation CD will not work and I looked online and downloaded drivers but still the same thing.

  Hi LOliver,

  Method 1: Run the hardware and peripheral troubleshooting tool and check if it makes a difference.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: Disconnect all USB (Universal Serial Bus) devices connected to the computer (unless your mouse and keyboard). Connect the printer and check to see if the problem persists.

  Method 3: Connect the printer to a different USB port and check.

  Method 4: Reinstall the USB (Universal Serial Bus) controllers.

   First of all, please disconnect all USB devices and then perform the following steps:

  (a) click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.

  (b) in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".

  (c) repeat step 2 to uninstall all items under 'USB Bus controllers'.

   

  Then, restart your computer and windows will automatically reinstall all USB controllers.

   

  HP printer drivers- ensure that you download the driver appropriate for your device model package.

   

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• PC to tv connection error "no signal - check the connections and the external device is turned."

  Original title: pc to tv connection

  I have an Acer Espire Vista 32bits. Connect to a Panasonic TC L32x30 HD TV. The TV has a 'PC' marked port that matches one VGA cable. I have the VGA end of the cable is connected to the TV. The other end is connected to the PC Tower via a DVI adapter to the port where was my monitor.
  TV output is set to "PC". I turned on my PC, the Acer (Bios) screen came. He then shows the block scroll bar. Just as Windows is about to light up, cutting signal. I never get to see my office. A message appears on the screen saying "no signal - check the connections and the external device is turned on."
  I had posted before saying that I had problems ranging from VGA to VGA. That's why I bought the DVI adapter to try another solution.
  I hope I made things clear enough for someone to help him.

  Hello Winston M,.
  I actually solved it. Went to the screen and chose. Connection just how I mentioned. second monitor, default Says. I then checked"Extend Desktop to this monitor.
  As I type this, I can see it on my TV screen.
  Thank you for taking the time to answer my question.
  Problem solved
  Ray

• No Notification sound when the connection/disconnection of USB device

  Hello

  I am running Windows 7 on a separate partition on a 2011 MacBook Pro (installed via Boot Camp).

  This laptop has two USB ports on the left side.

  If I connect/disconnect a USB device to the port more back, I get the notification sound as usual.

  However, if I log out these same devices to the port further there is no notification even if the devices are recognized & seem to work fine.

  Can anyone tell how to enable notification of this port please?

  John,

  Thank you for your response.

  The sound scheme has already been set to "Windows default", but just for good measure, I changed it but it made no difference.

  As mentioned be notified when you use one of the ports USB, but not the other.

  I posted this in an Apple forum & other users of this machine & installation are reporting the issue even if it seems to be a generic hardware problem & not just something on my own system.

  See you soon.

• Windows 7 does not recognize that a Canon canoscan 8000F is as a device when it is connected to the USB port.

  Windows 7 does not recognize that a Canon canoscan 8000F is as a device when it is connected to the USB port.  Tried unplugging, reboot & reconnect, in different orders, but the computer does not recognize there is.  Tried to install a European website for Canon driver: Scangear CS, 8000fvst8120a_xpen.exe, which is advertised as compatible with Windows 7.   But the installer does not work.

  Windows 7 Professional 32 bit.

  Hello Graboots,

  Thank you for your message.  You can plug your printer on another computer, in order to exclude the possibility that the problem lies in the printer?  You can try using a different cable, for this rule as well.  Since it is a question of recognition, we remove the external devices before software troubleshooting.  Do you get anything when you plug the printer (ie. a tinkle of connection)?  Please let us know, we are looking forward to hear back on your part.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Can I delay the prompt to begin to allow the USB device to connect in time?

  Hello

  I use a guest linux 2.6 on the host of windows 7 that is running a GPS Simulator she starts and sends the GPS signal on a USB port. However, it seems to begin quickly on the USB be detected. If I stop and restart the Simulator after than the VM has started, it works fine.

  So I was wondering if I can delay the start of the virtual machine so it has time to detect the USB device first.

  Thank you

  Hi TracMap,

  Welcome to the forums.

  You can add a delay of starting your virtual machine. Manually change the configuration of your VM's VMX file and add a new line with:

  -bios.bootDelay = "xxxx".

  'xxxx' is in millisecond. During this period, the virtual machine will stay on the screen of the BIOS in waiting for an entry and then start normally.

  I hope it will work for you!

  Good luck.

  Concerning

  Franck

• Error USB 'one of the USB devices attached to this computer has malfunctioned'

  Original title: Problem USB on Vista 32 bit.

  I have a 32-bit vista when I pug anything anyone posts USB the same message comes up saying one of the USB devices attached to this computer has malfunctioned and windows does not recognize it. Can someone please advise?

  Hello
   
  Method 1:
  
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us
  
  Method 2:
  
  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

• How can you stop safely remove hardware to appear when there is nothing connected to the USB ports?

  Orifginal title: Aggrevation

  How can you stop safely remove hardware to appear when there is nothing connected to the USB ports? It is causing my screen lock and give an error does not.

  Hi ElginCarelock,

  You can try to restart the computer and check.

  Uninstall all USB device manager entries

  a. Click Start and typedevmgmt.msc and press ENTER.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer and check.

  Hope this information is useful.

• The mistake that the USB device is not recognized... Help, please...

  I am trying to connect to Simple external storage drive and once I followed all the steps (only 2) Windows XP gave me a message that the USB device is not recognized or it malfunctioned. I disconnected everything and tried again in another USB port and still had the same error. I know that is not the usb port of my computer because I have it plugged into a port that just worked. I have Windowx XP SP2. Any help on this would be appreciated.

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner