Error during the full backup of the system Vista "Media is not UDF.

Similar Questions

• the system recovery media does not support this computer

  I have a HP G7-1365DX and the hard drive (750 GB) is a failure.  I did a recovery file on a USB key from the recovery partition and then replaced the hard drive with a 120 GB SSD.  When I tried to reinstall the USB system, I get the message "the system recovery media does not support this computer."  Is it because the hard drive was replaced by a SSD?  How to restore the system if the recovery disk does not work?

  Hello

  You are right about the source of this problem - HP recovery media often has problems of restoring the operating system on a smaller disk in quality than appeared on.

  There are a few options available.

  1. if the 750 GB drive is still able to operate, use your recovery media to perform a factory reset and then use software (or Windows 7 own imaging utility) for this clone of your SSD.

  2 create your own recovery media to use to run the installation - it would be my personal preference.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create an installation disk yourself using another PC - just download the good Disk Image ( this must be the version exact same origin supplied with your laptop ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and the software, you may need can be found here.

  Kind regards

  DP - K

• Pavilion 23-b244 AiO: the system recovery media does not support this computer

  Hey all,.

  I had a power outage (1 TB) HD material on me about a week ago and replaced by a (500 GB) SSD, not purchased from HP.  I then ordered the recovery disc from HP for this particular serial number.  Whenever I boot on the recovery discs, I get "this computer does not support the system recovery media. You are not able to restore the system with the media. "The Minsize argument in the instructions to build on the DVD file provides a minimum of 140 GB, so I don't think I have a new smaller drive system is the question.

  Last month I have updated the firmware to v80.08, and in the bios "product name", 'SKU number', 'serial number of the chassis' fields are all empty.  In "System ID", everythign is empty except UUID and family name.

  I think that's why I'm not able to boot to recovery discs?

  Any help would be appreciated, I have use this computer for quickbooks and have bee unable to do accounting for a week and a half.

  Figured it out! On my Pavilion, you press Ctrl + A in the bios then click on 'System IDs'. Then I was able to type in the ID to build my recovery and support the byte to feature on the sticker under my machine. F10 to save then the recovery media recognized the computer properly and booted up!

• DV6-6c15nr, "the system recovery media does not support this computer."

  Hi all. I'm trying to reformat my laptop (dv6-6c15nr), but when I try to reformat to f11the recovery manager f, all options are such that the system restore and restore to factory is grayed out. The next thing I tried was a set of recovery disks. When I used the recovery disks, it showed the message "this computer does not support the system recovery media. You are not able to restore the system with the media. 0110 A601UA #ABA - A1U60AV. Why can I not reformat my laptop... I remember that I was able to reformat until I sent offshore to get the hard drive and the radiator replaced by hp year last April. Now I can't get to... that this has to do with anything? someone please help...

  I also tried without the bios downgrade F.19 REV: a. which do not help either.

  It seems that the motherboard may have been changed and the information system (tattoo) has not been updated to match that of your computer. While I can't fix this for you, I can suggest some possible solutions and I work to spare;

  (1) you can contact HP Customer Support and ask that they correct the problem.

  (2) attempt to control that recovery discs for the model of the motherboard is currently labeled as.

  (3) If you can still read the Windows product key of 25 characters on the Microsoft COA affixed on the computer, you can install Windows 7 using this key. Please see "how to install Windows 7 without the disc" to get instructions on how to download Windows 7 SP1, create the installation media and install Windows 7 SP1 using the 25-digit key from the COA Microsoft on your computer.

  If you have any other questions, feel free to ask.

   

  Please click the White Star of KUDOS to show your appreciation

• HP ENVY PHOENIX 800-030qe: the system recovery media does not support this computer

  Hello!

  I can't recover to factory settings using recovery media (4 DVD) after changing HD (the previous device has crashed/broken).  The message is: "the media recovey system does not support this computer. You are not able to restore this system with this media. »

  So, what should I do?

  Thank you very much.

  Luiz Borges

  Upgrade the BIOS/downgrade will not fix it unfortunately.

• The system has encountered an error during the interview of the application. If the error persists, contact the system administrator

  Hi all

  We cloned an Oracle EBS R12.2.2 instance and it worked very well for us. To increase the RAM of the newly created virtual computer, we did the virtual machine down. Once the RAM has increased, we started all the services (without error), including level of DB and Application layer. But when we try to access the application of EBS get the following error:

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  The system has encountered an error during the interview of the application. If the error persists, contact the system administrator.

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  
  

  Then I checked all the services, they are running.

  
  

  Log file: / u01/applmgr/SCREWS/fs_ne/inst/VIS_ebsr72/logs/appl/conc/log

  --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Process of shell VIS_0402@VIS Manager internal simultaneous departure - ID 6095

  logfile=/U01/applmgr/vis/fs_ne/inst/VIS_ebsr72/logs/appl/conc/log/VIS_0402.Mgr

  PRINTER = noprint

  mailto = applmgr

  Restart = N

  diag = N

  sleep = 30

  PMON = 4

  quesiz = 1

  Reviver is ENABLED

  CP-SYSTEM ADMIN RESP. internal MISSINGThe competitor Manager encountered an error.

  Check the simultaneous log manager for more information. : APRIL 2, 2014 14:21:59 -

  Shut down the internal concurrent Manager: April 2, 2014 14:21:59

  List of errors encountered:

  .............................................................................

  _ 1 _

  Systematic AFPCSQ can't nec USER_ID value of the profile option. ORACLE

  error 1403 in get_responsibility_data

  Cause: get_responsibility_data

  has failed because of the ORA-01403: no data found.

  The SQL statement being executed at the time of the error was: and

  a exe

  .............................................................................

  APP-FND-01388: cannot read the value for option profile SQL_TRACE in routine and ROUTINE.

  List of errors encountered:

  .............................................................................

  _ 1 _

  Routine AFPCAL has received the code of failure while running or analysis of your

  simultaneous program CPMGR

  Examine your log file of concurrent application for more information.

  Make sure that you pass arguments in the correct format.

  .............................................................................

  The internal concurrent Manager VIS_0402@VIS ended with the State 1 - abandon.

  --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Note: Before you restart the virtual machine it worked great. It has not changed anything except the RAM to the virtual machine. After the start, we get error.

  I need your help. Please suggest me.

  Thank you

  Prabhakar

  Hi all

  Thank you for your support. I solved the problem. Find the info below.

  ===================================================================================================

  Question: Like I said existing VM is cloned VM. Then after we had changed the host name. I checked the database alert log file:

  Before the reboot: name of the node was the previous still node name VM that it functioned very well. (for ex: xyz.domain)

  After the reboot: name of the node is replaced by the new host name. (for ex: abc.domain)

  Once the name of the node is changed he started creating problem in starting the application services.

  One last thing, I want to mention here after hostname change, approval of new contextfile has 700, but it should be 755.

  Solution: I followed these steps.

  (1) stop all services on the LAYERS of the DB and APP

  (2) change the new contextfile permission if not 755 and the .env at the level of the source DB

  (3) cd $ORACLE_HOME/appsutil/bin and run as: perl adgentns.pl appspass = apps contextfile = $CONTEXT_FILE - removeserver

  (4) change the name from old host to the new host name, so find in contextfile.

  (5) start listener, then the database

  (6) listener status, it must must give service to the db instance

  (7) perform autoconfig with new contextfile (DB Tier)

  (8) perform autoconfig (pane APP)

  (9) start all services

  ======================================================================================================

  It works for me, and now the application is running. I hope that it will also work for others.

  Thank you

  Prabhakar

• STOP: c0000221 {Bad Image Checksum}. The image rpcrt.dll is possibly corrupt and recovery XP says error during the extraction process. Details of error: path not found___

  My friend turned on their laptop packard Bell recently and had the following problem. Windows XP screen loads but is then followed by a blue screen that says STOP: c0000221 {Bad Image Checksum}. The image rpcrt.dll is possibly corrupt. The header checksum does not match the checksum calculated.

  I can't the laptop to go further. I have accessed the Microsoft recovery Panel and try a non-destructive recovery as there are some precious photos that need backup. However, when you select 'no profile' to begin the recovery, I get the message:

  Error during the extraction process. Details of error: path not found

  I'm a bit of a novice when it comes to this sort of thing, but if someone can provide step by step help giving rise to lose photos, I'd be willing to give it a try. I also have XP Home Edition disk that came with the laptop but has never been opened. Any help would be appreciated. Thank you

  You hear your message said something about rpcrt4.dll?  It is important to relay the exact message you see.

  Please provide additional information on your system:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  You use some CD to access this Panel of Microsoft recovery where this "no profile" option is?  I don't know what all this means if it isn't some CD shipped with your system, in which case, I would use it for a coaster instead of something to fix your system.

  If the c:\windows\system32\rpcrt4.dll file is missing or afflicted, you do not start in the last good known Configuration.

  You also will not start in any kind of Mode safe no more.

  Even if you could boot mode safe, you would find that sfc/scannow does not work in Mode without failure in all cases (never).  If you try it, you'll see a message like this:

  Windows file protection could not initiate a scan of protected system files.

  The specific error code is 0x000006ba [the RPC server is unavailable.].

  Failed to start the RPC mode server safe either.

  I can't recreate your error exactly, but it is easy to replace the rpcrt4.dll file.  Looks like you have a working CD drive, so put yourself a Hiren boot CD and when you started on this, you can copy your precious files to a USB device for safety.

  There should be a backup copy of rpcrt4.dll already on your system, here or here:

  c:\Windows\System32\dllcache

  c:\windows\ServicePackFiles\i386

  You need to rename or replace the rpcrt4.dll file which is in c:\windows\system32 and replace it with one you will find the backup copies.

  There should be a backup copy of rpcrt4.dll already on your system, here or here:

  c:\Windows\System32\dllcache

  c:\windows\ServicePackFiles\i386

  When you get the Hiren's CD's, you can use to replace the missing or suspicious file.  If you need help with that, first get the Hiren's boot CD made and start over, then we can continue.

  Do you have a Hiren BootCD you can download here:

  http://www.hirensbootcd.NET/

  On the left, click on download, scroll down, choose the latest version, the download link is a little hard to see.  It is at the bottom of the page, above the drop for older versions and looks like this (click this component to download the ZIP file):

  Direct HTTP mirror + Torrent, Torrent Magnet

  Click the "Live HTTP Mirror" link to start the download and save the ZIP file on your desktop of somewhere that you can remember.

  The ZIP file is large, so the download will take probably some time to complete.  Then unzip the download to extract the Hirens.BootCD.ISO file that will be used to create your new bootable CD.

  Create a bootable CD. ISO file is not the same as simply copying the. File ISO onto a blank CD.  You must use software that includes how to burn a. ISO to a CD to create a bootable CD.

  File ZIP the Hiren is the file BurnToCD.cmd that you can double-click to launch it.  The BurnToCD.cmd will use the file BurnCDCC.exe to burn the. ISO file onto a blank CD using your existing CD burner.  You can also use your own burning software as long as your software is able to create a bootable CD. ISO file.  More modern burning programs can create a bootable CD. ISO image.  Create a CD from an ISO image bootable is not the same as just the file on a CD burning.

  If you need a simple and CD burning, this is a free software popular software:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your new bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.

  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When starting on the Hiren's CD, you will see a menu of options.  Choose Mini XP.  It will appear while Windows is loading and you will be presented with a desktop computer that has the look and feel of the interface of Windows Explorer, you are already accustomed to using.

  Using the Mini XP, you can access Internet, maneuvering around your system, search for files, copy files, replace the files and run the scans for malware, edit the text files (like the c:\boot.ini) etc.

  There are dozens of free and useful tools included in the CD that can be used to repair your system or copy your important personal files on another device (like a USB device or an external drive) in the case where you just give up and decide to reinstall your XP (I hope that you will not make this decision)

  Do, or do not. There is no test.

  I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• "The installation process has encountered an error during the installation of the shared technologies."

  Basically, whenever I try to download Adobe Premiere elements 11 on my Windows Vista computer, to halfway through a message appears saying that "the installation process has encountered an error during the installation of the shared technologies. If please restart your system and try again. »

  Whenever I insert the disc, I select the trial version, in case I have download the full version and it allows me to use my serial code.

  Someone said the destination folder could not contain more then 250 characters, then I changed its position of "C:\Program Files\Adobe\" in "C:\". ", but he still came up with the same message!

  I downloaded the new Adobe Reader 10, but this makes no difference to the process... no matter what I tried he always comes up with the same message.

  I also activate my antivirus software during the installation of Adobe Premiere Elements. Again, this is not do the trick. And I restarted my computer and tried to download it and not download more than once!

  Each time the same message comes back, and I have no idea how to fix... Its not my memory challenge which is a problem, because I currently have 50 GB free on my OS C:\ drive.

  I also have QuickTime version 7.6.9, which is apparently necessary?

  If you know something that I have not tried that can work, or the problem causing this and a solution to the problem, please can you let know me, thanks!

  Refer to this:

  Troubleshoot installation | Photoshop Elements, Elements first. Windows

  Mylenium

• Satellite P305D - different error during the startup sequence

  Hi I have a constant problem I have no idea how fix it. I have Windows Vista Home premium loaded and it works very well when it is running. I can restart the laptop several times and it starts perfectly, if I turn it off for an hour or two and go to start it always happens with a different error during the startup sequence. Most of the time I just go to start Windows normally and it loads, other times I have to go to the ERD.

  I uninstalled Vista and wipe the system well before reloading (using another drive) and the same thing happens. Would it be more likely to be hardware related? I know the battery charges well and I ran all the tools that Vista has to check the hard drive, so I don't know where to go next.

  Any help would be appreciated.

  Terry

  Hello

  Can you please post what errors you get during the boot process?

  In my opinion it could be a hardware problem, because you have already tried to reinstall Vista, so I doubt that the error is software related.
  Strange, but it might be a problem of RAM or HARD disk. The two parties, you can test it with Memtest86 and Drive Fitness Test. Google is your friend to find these two tools.

  In the worst cases, you must go to an authorized service provider. Technicians can check the entire notebook.

• Issue to receive the error message "the system has recovered from a serious error" while working on the computer and the computer restarts automatically.

  Original title: The system has recovered from a serious error-

  The system has recovered from a serious error-

  When you work in windows xp home edition, whenever this programe message and stop running and some auto restart machine.

  What is the solution for this?

  Hi Sandeep,

  Thanks for posting your question in the Microsoft Community forum.
  It seems that you have a problem with the error message "the system has recovered from a serious error," while working on the computer, and the computer restarts automatically.
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  Method 1: I suggest following the steps listed in the article and check if it works.
  Error message: the system has recovered from a serious problem
  http://support.Microsoft.com/kb/316424

  Method 2:
  I suggest you analyze your computer by using the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  Important: During the scan of the hard drive if bad sectors are found, the scanner tries to repair this sector, all available on which data may be lost.
  You can see the article for more information:

  A "System has recovered from a serious error" message after every restart.

  http://support.Microsoft.com/kb/317277

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• Try installing SAGE simply accounting error: "Error 1935. An our error during the installation of Assembly component

  Try to install simple SAGE accounting and the following error:

  "Error 1935. An our error during the installation of the Assembly {97F81AF1-0E47-DC99-A01F-C8B39A1E1873} HRESULT 0X80071A91 component. »

  After this error, I also receive this error:

  "Error: 1603 Fatal error during installation." Consult the help of Windows Installer (MSi.chm) or MSDN for more information.

  Anyone out there has any help with these errors?

  TKS!

  Hello

  1. are you able to install other programs?

  2. How are you trying to install?

   

  I suggest to follow the steps provided and check if it helps.

  Method 1:

  Problems installing and uninstalling programs on Windows computers: http://support.microsoft.com/kb/2438651

  Method 2: You can also configure your computer in a clean boot state, and then try to install it.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

   

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Hope this information is useful.

• 0xC1900101 - 0 x 20017 installation failed during SAFE_OS with an error during the START operation

  When you try to upgrade Windows 7 SP1 to Windows 10 ' 0xC1900101 - 0 x 20017 installation failed during SAFE_OS with an error during the START operation "is a problem recurring and none of the solutions posted for a Samsung RV511 work.

  When will there be a solution of Microsoft?

  Concerning

  Hello

  Since Windows 10 is a completely new operating system, the computer manufacturer might still not have designed and developed drivers for it. As suggested waiting for the manufacturer to release the necessary drivers for the hardware and then try the upgrade.

• Get the error during the installation of the regional coordination unit

  Hello
  I am facing the error during the installation of the RCU below. We gave the user sys and the DDT that works very well DOSPROMPT.the even when I give the configuration during the installation of the remote, I get the below error. Can someone help me with this problem.
  Thanks in advance...
  
  2012-10-02 22:52:58.645 NOTIFICATION rcu: oracle.sysman.assistants.common.dbutil.jdbc.JDBCEngine::connect: the connection to the database: user: sys, role: SYSDBA, connectString: (description = (address = (host = localhost)(protocol=tcp) (port = 1521)) (connect_data = (service_name = ORCL) (server = dedicated)))
  2012-10-02 22:52:58.730 rcu ERROR: oracle.sysman.assistants.rcu.backend.validation.StepValidator::isConnectionStepValidated: unable to connect to database: name of user and password invalid.
  Please enter the name of user and password valid
  2012-10-02 22:52:58.730 rcu ERROR: oracle.sysman.assistants.rcu.backend.validation.StepValidator::isConnectionStepValidated: SQLFatalErrorException:
  oracle.sysman.assistants.common.dbutil.SQLFatalErrorException: name of user and password invalid.
  Please enter the name of user and password valid
  at oracle.sysman.assistants.common.dbutil.jdbc.JDBCEngine.connect(JDBCEngine.java:585)
  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.connectDatabase(StepValidator.java:358)
  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.connectDatabase(StepValidator.java:253)
  at oracle.sysman.assistants.rcu.backend.validation.StepValidator.isConnectionStepValidated(StepValidator.java:1352)
  at oracle.sysman.assistants.rcu.ui.pages.DBConnectionPage.updateModel(DBConnectionPage.java:552)
  at oracle.sysman.assistants.common.wizard.WizardPageExt.wizardValidatePage(WizardPageExt.java:166)
  at oracle.bali.ewt.wizard.WizardPage.processWizardValidateEvent(WizardPage.java:710)
  at oracle.bali.ewt.wizard.WizardPage.validatePage(WizardPage.java:680)
  at oracle.bali.ewt.wizard.BaseWizard.validateSelectedPage(BaseWizard.java:2367)
  at oracle.bali.ewt.wizard.BaseWizard._validatePage(BaseWizard.java:3072)
  at oracle.bali.ewt.wizard.BaseWizard.doNext(BaseWizard.java:2152)
  at oracle.bali.ewt.wizard.dWizard.DWizard.doNext(DWizard.java:405)
  at oracle.sysman.assistants.common.wizard.WizardExt.doNext(WizardExt.java:261)
  to oracle.bali.ewt.wizard.BaseWizard$ Action$ 1.run(BaseWizard.java:3944)
  at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209)
  at java.awt.EventQueue.dispatchEventImpl(EventQueue.java:641)
  to java.awt.EventQueue.access$ 000 (EventQueue.java:84)
  in java.awt.EventQueue$ 1.run(EventQueue.java:602)
  in java.awt.EventQueue$ 1.run(EventQueue.java:600)
  at java.security.AccessController.doPrivileged (Native Method)
  in java.security.AccessControlContext$ 1.doIntersectionPrivilege(AccessControlContext.java:87)
  at java.awt.EventQueue.dispatchEvent(EventQueue.java:611)
  at oracle.sysman.assistants.common.util.EventPopUp.dispatchEvent(EventPopUp.java:94)
  at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269)
  at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184)
  at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174)
  at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169)
  at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161)
  at java.awt.EventDispatchThread.run(EventDispatchThread.java:122)

  3rd error is known, one can ignore it.

  Try it with the user of the system, I thought I told you that.
  This should work.

  Score pls help if

• Sync has encountered an error during the synchronization. Unknow error

  I get the following error message: 'Sync has encountered an error during the synchronization. Unknown error. Synchronize automatically retrying this action. "In addition, currently, my favorites are useless: I lost all my favorites and I can't add any new.

  Problems with bookmarks and history does not properly can be caused by a corrupted database places.sqlite file.

  You can check for problems with the database places.sqlite file in the Firefox profile folder.

  • http://KB.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
  • https://support.Mozilla.org/KB/bookmarks+not+saved#w_fix-the-bookmarks-file

• What can I do about 48 error during the update of the iphone 4S?

  What can I do about 48 error during the update of the iphone 4S?

  Hello! Try the procedure described in section of the Apple Support below:

  Solve the iOS update and restore error in iTunes - Apple Support