Films streaming Itunes to Sony TV via wireless connections?

Similar Questions

• How to make win 7 to prefer wired via wireless connections

  I have 2 internet connection in my laptop. wired or wireless. Win 7 prefer him wireless on the trendy though wired a metric is lower. How can I get win 7 to prefer wired via wireless connections?

  The average best absolute to ensure that you will always connect to wired and not wireless is to disable wireless on your computer. Just note that you need to re-enable it if you ever want or need to use wireless internet.

  To enable or disable the radio on your computer: click on START, then Contorl Panel, then Device Manager. Right click on the wireless adapter , then click on disable.

  To reactivate, simply click in the same place, which should read allow.

• I need to control my camcorder sony via LANC connection

  I need to control my Sony camcorder via LANC connection.  At the moment, I can control the camera through Tera term, through the serial port of the computer, via a LANC Sony controller card to the camera.  I would build a LabView program where I can click on the buttons to control the camera via the serial port.  Example: power zoom; Zoom out; etc...  I know that orders to control the camera because I typed them, Tera term.  How to associate orders with buttons in LabView for run commands?

  Thanks for your help.

  Before there was a structure of the event, everyone had to use a while loop with a case statement. At each iteration of the loop, the value of the control to the case statement must be read. This was/is called mark and used a bit of resources on the computer. With the structure of the event, nothing runs until an event is happening - no vote office and the resources of the computer used are minimal.

  The data event node returns different information depending on the event and the control that raises the event. In the example that you cite, the NewVal is connected to the structure of the case. It is the same thing that the control wiring, but in some cases, the command can be placed in a different event. You can have a single event triggered for multiple controls, and in this case, you might want to use the CtrlRef (control reference) to determine the actual control. There are a lot of possibilities.

  The option button is an enum. The case statement must match the enum values. Those who are not visible in the example. Right-click on one of the controls, then select the visible items > Label. If you change this, you will see the value in the change of the case statement.

  In order to send hex, you can simply right-click on your control station / constant and select "hexadecimal display. You can also use the Typecast and an array of bytes to a string. This question has been asked and answered hundreds (or even thousands) of times and there many examples of programs attached to these positions. Do a search.

• WRT610N - Itunes sharing does not work on wireless connection

  Material - WRT610N Version 1 Firmware version 03.15

  3 mac, many PC, HP Media Smart Server 3.0 Win7

  Sharing iTunes doesn't work on wireless connection, but works correctly with wired connection

  In case of problem until now:

  Has taken an old WRT54G to the closet.  Happy Macs with the file and printer sharing.

  Happy sharing iTunes music library.

  Took a WRT110 of the closet and once again so happy Macs with file, print share

  and Itunes library sharing was happy.

  I found an old file of firmware for the WRT610N (WRT610N_1.00.00.18_20080816) and flashed the

  router.  Again, everyone is happy, and I was really trying to work is now, Itunes

  sharing with the HP Media Smart Server works as advertised.

  Conclusion: something not in version 03.15 for full 610N router and hope to see it fixed soon.

  Aloha all

  Open the router setup page and a tab under Security, check the "filter multicast" option and save the settings. Now, check.

• OfficeJet HP 8600 N911a stopped printing via a wireless connection

  There are about 3-4 weeks our 8600 Pro Officejet stopped printing via wireless connection.  I tried to uninstall and reinstall the software on the site of andf also the HP CD.  I ran the software help HP and everytime it tells me to reinstall the software.

  The printer appears on the Wi - Fi and install it correctly every time.  I can print diagnostic pages, status reports to the printer from my computer without isse.

  Pages of test and all other documents will be not print.  He says that the printer is offline.

  I live in the country and there is no wireless connection close to home that he is recovering.

  Nothing has changed from what I can tell.  the unit is out of warranty now and to get help from HP, I would have to pay $40 to get telephone assistance.

  Is there someone out there who can help?

  Thank you.

  Try the steps in this post to restart the spooler: http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/hp-photosmart-premium-c310-printer-Windows-7-operating/m-p/1118873/highlight/true#M83583

• Loss of wireless connection on Satellite Pro L10

  I have a Toshiba Satellite Pro L10, with wireless capabilities built-in. I recently bought an ADSL Modem Belkin Wireless G Router. My desktop PC can connect to the internet via cable and cannot therefore have my laptop. However, when I connect to the internet via wireless connection my laptop sometimes everything stops. This isn't something to signal that I'm only about 2 feet from the router, and it is not that I can't connect to the internet, as I am on this at the moment. Is that in a few minutes, the connection will be lost and I can't seem to find what I can do about it.

  The other problem is that when I click the icon at the bottom right of the screen, the "Wireless network connection" window opens. Here, it shows the wireless network I'm trying to connect and it shows with a strong signal, but it is almost always said not 'connected '. He said never 'connected', even when I am connected to the net and surf away!

  Anyone has any ideas at all?

  It sounds a little to the Wireless LAN card is unable to obtain a valid IP address.
  These interruptions may occur for different reasons.
  But especially the new version of the driver Wlan and/or Bios should help resolve these interruptions.

  What card Wlan do you use?
  If you are using the Intel Wlan card you can also visit the Intel Web site to download the most recent version of the WLan driver.
  Please also compare the BIOS version available on the Tosh site with the version preinstalled on your laptop.

  Wlan card properties contain some useful options that could improve the quality of the connection. Energy saving options should also be required to check other functions in the tab advanced and disabled.

• Faxing via wireless HP OfficeJet Pro Premium 8600 - Win 7 64B

  I'm trying to fax directly from my computer using my P 8600 installed via Wireless.  Printing works fine, faxing from the itsewlf of the printer works fine, just trying to go green.  The driver shows Fax - HP OfficeJet 8600 network, Sami that the printer is configured, but I get the Sendfax error - cannot communicate with printer when faxing. What I'm missing here.

  Hi Brian-DS,

  When you did uninstall it and reinstall, did you use a download from hp.com for the re - install?  Otherwise, you could try doing a complete uninstall and then use a download from hp.com for installing the driver.  Click here

  If this does not help, I recommend you contact HP to Contact HP worldwidesupport.  They should be able to help understand you what is happening.  It would be good if the agent is able to your computer remotely and all check.

  Let me know what happens.

• Why doesn't my computer series sony vaio y cannot detect / connects to a wireless connection

  Why doesn't my computer series sony vaio y cannot detect / connects to a wireless connection. only through connection cable/usb... Please help me... Thank you...

  Hi JaqD,
  to go with that said Brian, more in detail the best options, we can give you.
  In the meantime, here are some generic troubleshooting steps:
  http://support.Microsoft.com/kb/313242

• Cannot conect to the internet via a wireless connection secure, despite having completed the restoration of the system.

  I have a Dell laptop which does not connect to the internet via the wireless connection.   I can connect via a line to broadband, but not the wireless.   My work PC and iPad are connect.  I tried compand repair network and he says that the problem is resolved.    I tried a system restore a week before that the problem started.

  Any other suggestions?   Thank you

  Most often when a device is not it's because of a driver.  Try reinstalling your.

  It works for vista, win 7 & 8

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• Where can I find the serial number for Sony SRS - BTV5 Wireless Speaker System?

  I recently bought a Sony SRS-BTV5 wireless speaker and I am trying to register the product on the Sony Uk site.  Where can I find the serial number?

  The volume buttons is a flap for the charger and audio, which opens and tip the enclosure on the side, you will see the serial number above connections

• I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity.

  Wireless router / Internet problems

  I am running Windows Vista Home Edition with Security Essentials.  I can connect to my wireless router, but cannot get internet connectivity via Wireless.  If I connect the cable to the port on the router, I get internet connectivity.  Is there a firewall setting that could cause this problem?

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• How to display PC on TV via a wireless connection

  Discover my computer on my tv

  How can I see my computer on my TV? I use a wireless connection and I have a WII connected to the tv and the network?

  Hi Reddogoh,

  There are two main options that I see in the connection of your television to the computer. One is a hardware solution by getting a TV tuner card, the second would be a software solution by using your internet connection (this should be a high speed / broad effective solution of the band) to stream TV on your PC. Each of these types has its own unique advantages.

  Hardware solutions (TV Tuner):

  First, there is the direct connection method. Examination of the main material here is the tuner TV for your PC card. An example of a vendor for this would be here:http://www.hauppauge.com/. The study in this case is to make sure that you have the right connection from your TV on your PC. There are several types of connections that could potentially work from your TV for PC: coaxial, RCA, S-video and VGA are some of the most common. One of the most interesting types of connection on the site mentioned would be a device which can converts a signal from coaxial cable from the TV to a USB device, which can then be plugged into your computer. One of the benefits of a hardware connection TV is the ability to record live TV, and the software for this feature is often included with the TV tuner. You can use wireless? We can as a type of adapter, but mainly the links are direct.

  Solutions software (Streaming and porn TV on broadband):

  Software solutions can be very economical because it piggy back on your existing broadband connection. Another advantage would be that the shows can be listened to on request.

  Prices can be as low as free, one example beinghttp://www.Hulu.com/ where you can listen to the full episodes of television through a license agreement between the content providers and Hulu.

  An example of a subscription model would be http://www.yourfreetelevision.com/ , which is about $30 every month.

  So, there are a few options and this should certainly point you in the right direction.

  (If this post was helpful ("vote as helpful") orAnswered ("mark as answer") to your question, please click on the corresponding button to help others find the answer more quickly.) Besides, if you feel that someone else has been useful, mark them too. Also, if you have any othercomments please let us know.)

  Hope this helps,

  Steve <> Microsoft Partner

• Computer laptop Windows 7 can see other wired PC via a wireless connection by specifying the box "search programs and files" drive letter in the start menu, but not in the network screen

  My laptop with Windows 7 (64-bit) can not see the other desktop PC running Windows XP via a wireless connection, except if it is plugged into my laptop so only I can see them on the network.
  I checked all the working groups to ensure that all are the same.

  However, when my laptop into Wi - Fi, I could see the other wired desktop PC by specifying the network path in "search programs and files" to the start menu in the Windows 7 laptop, I was able to add network folder by specifying the drive letter for the connection and file I want to connect via a right click on the network to connect a network drive...

  Then, finally I can access any other desktop pc wired to shared folder via the Wi - Fi by this method.

  But I still don't see them on eventhrough network I can access by this method. Please help me solve this problem.

  Hi Hkway,

  • You are able to see the Windows 7 machine Windows XP computer when connected through wireless and if it is accessible through network?

  First of all, check if the NetBIOS protocol is installed on your Windows XP computer. To install the NetBIOS Protocol, follow these steps:

  1. click on start, click on Control Panel and then double-click network connections.

  2. right click on the card that you want to add NetBEUI to and then click Properties.

  3. on the general tab, click on install.

  4. click on Protocol and then click Add.

  5. Click to select NetBIOS protocol in the list, and then click OK.

  6. restart your computer.

  Also make sure that NetBIOS over TCP/IP is enabled in the Windows XP computer. To do this, follow these steps.

  Turn on NetBIOS over TCP/IP

  1. click onStart, click on Control Paneland then click on network connections and Internet.

  2. click onnetwork connections.

  3. right click onLocal area connectionand then click Properties.

  4. click onInternet Protocol (TCP/IP)and then click Properties.

  5. click on the tabgeneral and then click Advanced.

  6. click on theWINS tab.

  7. underNetBIOS setting, click Enable NetBIOS over TCP/IP, and then clickOK twice.

  8. click onclose to close the local area network connection properties dialog box.

  9. close the network connections window.

   

  After following the above steps, check if you can access the computer Windows XP of Windows 7 computer using the wireless connection.

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• VPN via wireless

  is it possible to site vpn with ipsec on routers tha is linked via wireless?

  Thank you

  Celso,

  If the two routers are

  a be able to communicate with each other.

  b. is not far behind,

  c. and there is nothing on wireless devices that would block packets UDP 500 and ESP.

  Then, you shouldn't have a problem with creating a Site to tunnel.

  Hope that answers your query.

  The rate of this post, if that helps.

  See you soon

  Gilbert

• Unable to connect via wireless

  Hello

  I use a HP Pro book Windows7 professional. All systems were functioning well when the wireless connection has been disconnected.
  Later my laptop cannot connect via wireless even if system the wireless still work correctly on my ipad.
  Please tell us what I should try to fix this problem.

  You have run the wireless troubleshooting tool? - http://windows.microsoft.com/en-US/windows7/Using-the-Network-troubleshooter-in-Windows-7

  Is your wireless network of the specified interface as active or disabled, if disabled then re-enable-control panel, network and sharing Center, change the settings of the map, right click on your device to turn on or off (you will be asked for admin at some point).

  PS - extra thought, some laptops have a wireless switch network. It is not struck off there?