G62-b51SI | XT896EA | Laptop G62 no boot

Similar Questions

• G62-b51SI | XT896EA | G62 notebook PC

  G62-b51SI | XT896EA | Drive Self Test error codes 03F1, 0303 and 0301, how can I get it back

  Hi Schiduku

   

• I received an update on your part 10/11/10 and now my laptop will not boot in place! I need HELP.

  I received an update on your part 10/11/10 and now my laptop will not boot in place!  I need help.

  Hi bobbymh,

  -Do you happen to remember the update has been installed?

  -You receive an error message when you try to start the computer?

  Follow the steps below:

  Method 1:

   

  Try to start the computer using the last good known Configuration and check if you can successfully start.

   

  For instructions, see How to start your computer by using last good Configuration known as Windows XP .

  Method 2:

  Perform the system restore from SafeMode to a restore point prior to the show and check if this solves the problem.

  See to run the system in safe mode restore

  See also How to restore Windows XP to a previous state

  Method 3:

   

  Follow the steps listed in the following article:

  How to fix a computer that does not start

  Gokul - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• G62-b51SI | XT896EA | G62 Notebook PC Window 7 Home Premium no boot

  Laptop does not start, the self-test of the disk gives error codes 03F1, 0303 and 0301, how do I get it back

  Replace the HD and recovery disks to restore the image. Call HP support if you're still in warranty.

• Computer HP laptop crashing after boot up on G62 Notebook

  Hi, I have problems with my laptop computer lately its been run very slowly and last night it froze completely. Hoping I could get some help here.

  Product: HP G62 Notebook PC WQ848UA #ABA

  OS: Windows 7 64-bit

  Hard drive 1 error

  Failure ID:0XJFUF - 54 M 645-XD003G-60RM03

  Hello

  Please find the link given below check Chapter 4 withdrawal procedures and the replacement part number of the hard disk are also listed check page 46 will help out you.

  http://h10032.www1.HP.com/CTG/manual/c02641795.PDF

• G62 laptop don't boot-DST short failed

  Hi, I have a 2 years, HP G62 - 407DX Notebook PC that will not be in service.  It doesn't have the start, lapping, sytem update and test drive with a short outage DST in each.  The error is QE07W4-5HK6GC-XDO141-60WQ03, hard disk 1.  Any suggestions on how to proceed?  Thank you.

  You are the very welcome.

  Replacing a hard drive is easy to do.

  See the manual on the link below, Chapter 4.

  http://bizsupport2.Austin.HP.com/BC/docs/support/SupportManual/c02641795/c02641795.PDF

  If you don't want to purchase recovery discs for your HP PC (that you can find info on the link below), you can also make your own Windows 7 If installation disc you can read the 25-character windows product key 7 on the bottom of your PC.

  http://support.HP.com/us-en/document/bph07143

  Here is the info on how to make your own install of W7 disc.

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

• G62 Intermittent boot failure

  Over a period of several weeks, this 5 year laptop has developed a failure intermittent startup.

  I went through all the suggstions found on various forms (running the diagnostics of F2 and F10 etc.; replacement of battery) and found yesterday when everything started normally!

  This morning, after having run the new battery down to compress and recharged during the night, the lapyop was to his old habit--won't start do not.  The fan should run at high speed for a few seconds then continues quietly with no display.

  While trying to access this forum on an Android Tablet (no luck) the laptop decided to come to life spontaneously long after pressing the Start button.

  The result of the diagnosis of F2 showed a failure ID: GGFXPT-5A47P2-9XL03F-60QE03, but running a diagnosis deepened from the BIOS gave no error some!

  I was on the point several times of just this "thing" reveling in the tray, but would welcome that there must be a permanent solution somewhere out there.

  Hi there @s_gw,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I looked into the problem you are experiencing with your laptop. You had mentioned receiving a failure ID: GGFXPT-5A47P2-9XL03F-60QE03. Identification of this failure code is the code for "Hard disk 1 Quick Test Failure".

  This failure Code is related to the hard, I suggest that you save all important files as soon as you can.

  Here are two documents that will help you solve the problems to find the root cause.

  1 HP laptops - Hard Drive failure errors: failure Imminent, Smart, BIOHD, HD535, etc..

  2. HP Notebook PC - hardware failures (Windows 8) screening.

  If this is insufficient, please use the following link to create yourself a file number and then contact us:

  Step 1. Open the link: www.hp.com/contacthp/

  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  
  File number and phone number are displayed.
  
  They will be happy to help you immediately.

  Please follow the troubleshooting provided and save all your files. IF you need assistant extra, I'd be happy to help, I just need your model number (How can I find my model number or product number?) and which Windows operating system you are running?

  Thank you!

  Have a great day!

• HP Pavilion 15 PC laptop: laptop won't boot up - stays on the black screen

  My computer was working fine and then all of a sudden the screen went black.  I turned the power on and it came up with the error message "Unmountable Boot Volume" and then tried to solve the problem but just stayed on the screen black and never solved the problem.  I turned it off, did the hard reset when I remove the battery and hold the power for 15 seconds, but it's always the same.

  I went into the mode where I can try to restore the computer but it does not allow me to do. They say it restores and then just black.   I also ran a report where it says that the problem is "short hard drive DST Check: failed ' and gave me a code of 0SNHWW-7N987K-MFPWMG-60WF03.

  If there is nothing that can be done to help me I would be really happy I have use this laptop for work and really need to get it back running of emergency with minimal cost.  Thanks a lot for your help

  @Amyynatalia,

  The pleasure is all mine!

  I'm afraid not, you will be asked to pay more for the replacement drive as its not covered by the warranty.
  
  Keep me posted!
  
  Kind regards

• Pavilion dv6-3225dx: laptop fails to boot after upgrading RAM.

  Hello

  Recently, I tried upgrading my laptop RAM 8 GB which is max you may have to wait. The RAM sticks were (x 2) DDR3 4 GB Samsung 1600 12800 mhz 1.35v. The system has detected the new RAM, showed the new memory and even spent the memory test. But this isn't the windows startup. I tried to clear CMOS. But without success. Do not let me windows. BIOS version is up to date (F29). Is there any setting for this?

  Thanks for all the help!

  Hello:

  Please see this discussion.  It must be very picky about what memory you use in your model series...

  http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/Pavilion-DV6-Windows-10-wont-boot-after-memory-upgrade-4Gb/m-p/5776161#M359223

• My laptop won't boot at all

  Last Monday I was on my laptop and the battery came out while it's on, because then it does not start, I tried pressing F8 to start mode without failure, repair or mode and all I get is a white screen.

  I tried to boot from a Windows 7 repair of my CD drive disc and it gets to half way then fails. What is the problem with the system can be wiped and restored to factory setting or is it irreparable?

  You can enter the BIOS settings? HARD drive recognized and properly list?
  Set it to default settings please and try reinstalling the operating system.

• HP laptop: recovery disk boots, but no mouse cursor to select the options.

  I started the HP recovery cd and it gets to the menu asking what to do - there is no cursor mouse so I can't use it.  Arrows, page up/down, alt + tab, etc. do nothing.

  F1 brings up 'any aid found' so that the keyboard works.

  I was able to use a paragon boot cd (linux) & mouse/keyboard worked fine, but of course, I can not restore the system with it.

  FWIW: the laptop crashed and lost network connectivity, so I used system restore to go back (on the 2nd try) - 36hours after waiting until the end; I turned off & of course, it wouldn't start with various errors depending on if ordinary start-up or secure boot... If I want to use a system restore to reset some system files in order to start up and down my files.

  Find the USB Wired mouse, plug in and try it.

• Pavilion 15 laptop: HP Pavilion 15 computer PC2170 laptop does not boot to Windows - 2 years

  Hi, my Hp Pavilion is only 2 years and 2 months (not very old at all) but suddenly it does not start in Windows, it hangs at the HP logo screen, it starts with an HP logo screen then goes to another screen of the HP logo, and then freezes. I can't get into safe mode.  I got in the Hp diagnostic screens and I conducted tests on all and everything.

  I did a hard reset, still frozen.

  I removed the cover, he went out and placed him in, still nothing.

  Whenever I have to try and reset it, he said administrative privileges is necessary, but there is no administrative privileges on this computer.

  There is no restore point.

  I ran chkdsk via the command prompt and had no error.

  I tried running sfc: scannow but I had which was something in the meantime and could not do.

  The laptop is: laptop HP Pavilion 15 2170

  A6-5200 APU AMD processor

  Can someone computer whizz out there enlighten us on this you problem, please.

  When you request support, please provide the model name and product number complete (p/n) of the HP computer in question. HP/Compaq made thousands of computer models. Without this information, it can be difficult, even impossible to help you solve your problem.

  The information requested above are on the bottom of your computer, inside the battery compartment or on the BIOS boot screen. Please see How can I find my model number or product number? for help more to find this information. DO NOT include your serial number.

  

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Laptop used fully boot up

  I have a HP pavilion ze2000 laptop and when I don't boot it all that I see is my wallpaper, no taskbar, no icons, etc... What is the problem?
  I can access the Task Manager, but when I use it to stop its says 'explorer.exe' is now closed and I have the option to end now, but when she finishes he stop I is hold buttn power to close.
  Told me it's the hard drive, but I did a ' disk hard self test "and it passed then is it's just the BONE? If I have XP reinstaled it fix it?

  Hi Dunne08,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?

  I suggest that you try the following steps before you reinstall Windows XP.

  See the Microsoft article and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• My laptop won't boot. All I get is a white, black screen with the cursor flashes in the corner.

  I tried boot cd of the Hiren s and changed the boot order to cd drive.  That did not work.

  My laptop is a compaq, about 8 years old and winxp.

  Press ctrl-alt-delete. If it works, go to file / new task, type explorer.exe. This brings to the top of the desktop computer? I wouldn't use Hirens CD. Go into the BIOS and change to the hard drive. If windows is installed

• HP ENVY 17-j020us Quad Edition: installed SSD and Windows 7, now the laptop will not boot

  I replaced my hard drive Windows 8.1 with a PNY 240 GB SSD and Windows 7 64-bit.  Everything worked very well! Installed all the drivers, everything has worked very well!  Restarted several times, everything worked fine!  Portable stop for the night, the next morning I turn on the laptop and get this error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I've traveled different repair procedures using the ERD Windows 7 without change.  I have reinstalled Windows 7 with SSD formatted as GPT drive, received the same error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I have reinstalled Windows 7 SSD formatted as MBR disk withs, received the same error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I removed the SSD to the laptop and placed in a desktop pc, pc works fine, no problem with the SSD.  SSD in laptop, got the same error message: "boot device not found, please install an operating system on your hard disk, hard disk 3F0".   I don't know where to go from here.

  Help please...

  Okay, I'm running.  In the System Configuration UEFI clicked 'Load HP Factory Default keys', this restored "Secure Boot" who has restored the laptop as long as you work!  Thanks for the help.