grayed out with the new video card 3D functionality

Just installed a NVIDIA GeForce GTX 660 with 2048 vram and 3d functionality is not accessible.

You need to go to NVidia Web site and download older drivers for your graphics card.

Tags: Photoshop

Similar Questions

  • Computer does not start with the new video card

    Hello

    I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

    The video card is
    Sapphire ATI over-pants 2460

    I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

    It seems to me to have the latest version of the bios and windows 8

    What can I do else?

    Thank you very much

    Best,

    Korhan

    Hi JM,

    Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

    Your PC comes with one of the following built-in Intel graphics drivers:

    • Graphics Intel HD 4400 (GT2)

  • H8 1241: problems with the new video card on h8 1241

    OK, I've seen a lot of posts on this topic, but I couldn't find anything yet. I bought this computer as a windows 7, but have just upgraded to windows 10. The stock video card HDMI port came out, so I ordered an ASUS Geforce gtx 750ti to replace.

    http://www.Amazon.com/GP/product/B00IB9P1KG?PSC=1&redirect=true&ref_=oh_aui_detailpage_o00_s00

    When I try to boot with the new card I get the blue screen that tells me to Press esc to get into the BIOS, but it is freezing it (I am not able to get into the bios).

    Currently, the only way to make changes are re - insert my old card. I can not even start without secondary card by using the on-Board (which could as a result of the changes that I made in the BIOS). Most of the solutions I've seen involved changes in version 8 of the BIOS but I can't get that. I tried to update my BIOS to the latest version for windows 7, but I don't think it worked b/c I am on windows 10 now.

    Help, please!

    Hello

    The level of your PC motherboard BIOS is not compatible with the cards NVIDIA GXT 7xx series.

    Contact ASUS to obtain redress. ASUS has maybe a video BIOS update or a different graphics card that will work in your PC.

    A NVIDIA GTX 660 new or used may be your best bet.

    Thanks for posting on the forum.

  • 310 - 1125y in expansion with the new video card?

    I have a HP all-in-one TouchSmart 310-1125y and would like to know if this PC support the installation of a new video card.  It comes with an integrated ATI Radeon HD 4270 support.  I did some research and have the impression that this PC is not particularly expansive.  Thanks in advance for your help.

    Here are the specifications of your desktop HP TouchSmart 310-1125y and its custom Quanta DA0NZ2MB6A0 (HP Aronia) motherboard. According to the specifications, there is no provision for the installation of a new video graphics card.

    Frank

  • 800 - 030qe envy: conflict with the new video card

    I bought and installed an EVGA GEForce GTX960 graphics card and discovered a conflict with the SATA cable on the motherboard connector. EVGA has recommended that I find a SATA cable with a connector at right angles. Can anyone suggest a source for a suitable cable? Mine is red (?).

    @bobsun2, welcome to the forum.

    This is a cable that should work for you.

    Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

  • Pavilion Slimline s3120N will not recognize the new video card

    I can't get my computer to recognize and use a new video card. I tried 3 cards (GeForce 8400GS... cards 2different and Radeon HD 4550). The computer continues using the onboard video. For each card, I did the following:

    Go to configuration, advanced and changed the main graphics card 'on board' to 'PCI-E '.

    Saved and let the computer start.

    Stop and insert the new video card into the PCI-E slot

    Start the computer and installed the latest driver

    Computer restarts

    No matter what I do, it always uses the embedded video. I am running Windows 7 Home Premium. How can I use the PCI-E slot/video card? Any suggestions?

    I think that your problem may be the power supply unit (PSU).  The video card that you have installed require a minimum of 300W/350W.  The power supply of your computer is perhaps only 180W; 220W at the most.  You can check by opening the case and by reading the label on.  It's just too much difference for the card to function properly.

  • Install the new video card

    I have a HP Pavilion m7500y PC running Windows XP. I would like to install a new video card to display on both monitors. Installing a video card is possible with this machine? The card I have has a VGA, HDMI and a DVI input connection. If possible, do I need anything special to install and use this card? Thank you for your help.

    I wouldn't worry the food until the video card is selected.  Decide if a new power supply is needed.  Many new cards high power have a 'special' which will have all the power supplies.  According to the map, adapters for power fittings may come with the card.  A respected power supply name is Cosair, Antec, or Thermalake, but many are just as reliable at the best prices.

  • Help blackBerry Smartphones! Bold 9700 is frozen on start up with the new sim card

    I tried looking for similar topics but could not find more relevant. everyone seems to have no problem with swapping of cards sim on their fat. If there is a thread already open, I'm sorry. I am really frustrated and really need my blackberry to be operational.

    I have a Bold 9700, updated to the latest OS, everything works fine. I recently had some problems with my old sim card so I went to my service provider to change to another (same number, same line, same contract, just a new sim card).

    As it is expected that I was told that when my old sim is disabled, simply insert my new and I use my phone as normal.

    However, when I did this, the phone was stuck at the loading screen (the bar is all white) for eternity (maybe 5 minutes or more) before moving on to the home screen. There is no charge "security check" bar, the phone is completely frozen, no buttons work, the touch pad does not work, it shows 3G top right without the sign of blackberry, there is no service provider name and from time to time the little loading logo clock is displayed.

    I pulled the battery a couple of times and the problem persists. I called the service provider to reactivate the new sim card, they did 3 times, same problem. I inserted the SIM in other non-blackberry phones that I have and it works on all phones. When I put my old sim card in the 9700 disabled, the phone start end in 2-3 minutes, 'check' safety bar according to normal, everything moves, just no connection to the service. When I turn on the phone without sim card it starts fine with a message to say out loud the card sim.

    I even went down to the assistance service technique blackberry from my service provider and they were no help. all they could say was 'we must wipe your phone and reload the software' that I'm trying to avoid, and I can do it myself anyway.

    My phone is unlocked, comes unlocked here in Singapore, I even checked using the method 'MEPD', all disabled.

    This was very frustrating, especially when I need my blackberry for work. What is the problem with my phone? How can the simple replacement of a sim card if difficult on a blackberry when there is problem free for ANY other phone I've ever used? I am now fear when I travel abroad for business and requires a foreign sim card.

    had the same problem and eventually happeing is that I had to reload my os permeable, and then insert the sim card and upgrade again.

    consusming time, but worth it

  • Qosmio G10 with the new graphics card and pcb - CD update tools do not work

    Hello world

    I hope you can help me. Before a few weeks, I received my Toshiba Qosmio G10 return of aid, because the laptop no longer works. So I get it back with a new graphics card and a new PCB. With my laptop I have a CD called the update tool CD and a sheet of instructions, where it says to start with this tool CD-Rom update after you have installed the Windows with the reovery CD.

    So I did, but when I know the update tool CD to put in and I start with it, the computer installs something, but after a short then it is a message that it is a different model and that I have to put a button to close Notepad. So I did it, but Windows does not start.

    Why is it so? I had done everything that has been said on the instruction sheet.

    Please help me

    Hello

    It will be interesting to find more information on this CD-Rom tool update. Are there tags Toshiba? Can you please write what is described here?

  • Pavilion p6 - 2120t: Windows will not start with the new graphics card

    Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

    HP Pavilion p6 - 2120t CTO desktop PC

    Configuration:
    Intel Pentium CPU [email protected]
    4.0 GB RAM
    Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
    Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

    BIOS to Version 7.18

    Running:
    Windows 7 Home premium 64-bit w/service pack 1
    Two monitors (VGA, 1 digital port 1)

    Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

    For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

    I plugged both monitors to their connections voted on the new map.

    When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

    The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

    Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

    Tried the above process two more times with the same results.

    I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

    > Sources of boot UEFI

    Windows Boot Manager

    > Sources of boot legacy

    ATAP I CD/DVD player

    SATA2

    Hard drive

    SATA0

    Network controller (Realtek PXE B06 D00)

    PC using UEFI Boot Manager Windows boots normally

    I have not tried Legacy Boot Sources because I don't know which one to choose.

    I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

    I know that others have had a similar problem but I have not seen a solution that works for my PC.

    Any advice would be welcome.
    Thanks for your time.

    Hello

    Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

    The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  • C168i: unlocked from at & t, but unable to connect to the network with the new SIM card

    I brought my c168i from the USA and I can't use it in my home country. I unlocked the phone to at & t, but it connects to the local network with the new SIM in there. It shows "not available" or "no service". What is going on??

    If you look at Australia GSM worldwide site, you will see which bands are available in your area. If the bands including the phone does not match the country you are located in the phone up with will not get service. Not all bands are available in all areas. In my view, that the phone only has GSM 850/1900 GPRS. This would mean that you get only service when GSM 850 is available that I don't see 1900 in Australia.

    Mark

    Support Forums Manager

  • The HP ENVY h8-1500z with a new video card upgrade

    Hello

    My current video card is a 1 GB of Nvidia that came with the installer and requires more power.  I want to upgrade the video card for this (http://www.newegg.com/Product/Product.aspx?Item=N82E16814131562) this map requires power and this kind of care.

    I opened my PC and it looks like the current power is 300W, but I do not see a card for a video about this card. My question is: Y at - it sort of an adapter I can use with existing PS? If I need to exchange the PS, can I use any power supply in this PC? It will be (http://www.newegg.com/Product/Product.aspx?Item=N82E16817139050) to adapt and work? If not, what suggestions do you have?

    Thanks for the help.

    Wanted to add that I am running:

    6-core AMD FX 6120 to 3.50 Ghz

    14 GB of RAM

    64-bit OS Win Pro 8.1

    NVidia GeForce GT 620

    The graphics card, you want to install on your computer requires a minimum of 500 watts power. The Corsair CX500M that you access will work for your computer and work with your desired graphics card.

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

  • Put the new video card into m9000 with an edge

    I need this m9000 to be able to output to two screens (where the office is extended and the mouse moves between).  It has an integrated video card, so I guess I'd need to purchase and install a separate to get this feature.  I've never been a video card to a computer that already has an edge - is - how complicated?

    Hello

    Your PC has only a 350 Watt PSU unless you had replaced him with a bigger power supply.  The NVIDIA 450 needs a 400 Watt power supply.

    This NVIDIA GT 440 1 GB DDR5 will work with a 350 Watt PSU.

    Review the performance of NVIDIA specifications. Look at the specifications of strip memory bandwidth and level of DirectX support.

  • Installation for the new video card will not work. Message "Hardware not detected" what's the problem?

    Windows XP Home Edition. Motherboard ASUS P4PE. (Old) NVIDIA geforce4 TI 4400 failed - video card replaced by Prowler Radeon 7000 64 MB agp (Mad Dog). The black screen with the old card and bought a new one. At out the old card and installed a new.  Start the computer and graphics were. With Nvidia drivers installed, display settings could be changed. Device, 'Monitor' Manager showed now default monitor instead of good Sony monitor. Remove all drivers video and rebooted.  Screen "new hardware found" appeared, but I couldn't get the new drivers loaded. I inserted the disc by the manufacturer, but the pilots has not can be detected. Has attempted to launch "Setup" on the disc, but received a material not found error message. Yellow mark points to "Other devices" and the hyphen "VGA Display adapters". No 'monitor' in Device Manager. Tried to turn off the windows firewall and Virus software. I tried windows update. Still have a problem. What's wrong?

    The old drivers must remove the first test pilot seeper guru3d.

    The nvidia Setup program should find the material but otherwise download the latest version of the software from their Web site.  They must be the pilot, right down to the revision number, not only the model number.

  • Xlib & quot; sequence lost & quot; with the matrox video card

    I am trying to run labivew (8.2) tools (for example, nispy) on a system running redhat Linux 4 (2.6.9 kernel) with a video card Matrox P690 installed.

    Initially, I had a problem with libvlrt not being able to run because the _glapi_get_context symbol is not found. By loading a different combination of Mesa and openGL libraries I can get it to not complain about the coast, but the app crashes then go out with...

    Xlib: sequence lost (0x10000 > 0x6b) in its response of type 0 x 8!
    (null) X error of requests that have failed: 0
    Major opcode of requests that have failed: 0)
    Serial number of requests that have failed: 0
    Current serial number in output stream: 107

    If I use a NVidia video card or start a VNC session, so I don't have the problem, so it seems that there is a compatibility issue with the Matrox driver. I have the latest driver from Matrox.

    All the known world it or something similar and found a solution?

    Hi rpoffen,

    Looks like it's a different flavor of this post on the forum. Let's get some versioning of the road information. What version of openGL and libraries Mesa, Matrox drivers do you use? I doubt that we have a video here Matrox card to try, but I'll look...

Maybe you are looking for

  • Using Applescript for formatting lines in figures

    I have a Numbers spreadsheet where I want to shade the lines according to the (odd) values in my second column (B). I've been everywhere in the forum, but I can't seem to find a script that is, and I can't change one and make it work. Anyone with a f

  • Media bar stopped working on my Qosmio F50-126

    I have a Qosmio F50-126 and bar media (next to the switch) stopped working and answer since I did the cover... the lights in the corners has also stopped working. What is the problem?Please help me...

  • Portege Z30 - A - 18 M - unavailable two-finger tap

    Hello I just bought the Z30 - A - 18 M and (of course) love it! The only thing that bothers me it is the inability to tap with two fingers to right click and click on three fingers for a midfielder. I saw some people describe the two fingers tap and

  • Want to reinstall Vista

    I have my laptop with Vista but I installed Windows XP in there, now I want to install windows Vista again until I doHow to recover my old vista or tell me another way to solve this problem?

  • "Add or Remove Programs ' opens but does not fill.

    original title: "ADD or REMOVE PROGRAMS ' opens but does not fill. I bought a rebuilt SONY DESK TOP and have used it for over a year and it ran ok. The unit was pre loaded with Windows XP Home Edition and it came not with a XP disc.