Help connect Dextop Remote queue (win7) with the Iphone 5 by using the client RD

Similar Questions

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• Is it possible to connect my Application ' Stop' button with the "Run" button of LabVIEW?

  Problem - one of my clients recently tested my new LabVIEW application and asked how the arrested LabVIEW application can be restarted without clicking on the "Run" (right arrow) button.

  Is possible solution - possible to connect my Application ' Stop' button with the "Run" button of LabVIEW?

  Thank you!

  Barry

  The big problem is in your Acquistion to stop audio event. You run the LabVIEW stop sign which is the equivalent of hitting the Cancel button in the toolbar.  (See contextual help on that).  You can stop the acquisition, but you don't want to stop your LabVIEW program.  You need this case in the event your computer to transition state in a sleep mode when you do not make any purchase.  Then hit the purchase button to start again transitions the machine state in the acquisition.

  In your case of program output, you want really to leave LabVIEW it.  You want to run and stop commands like closing the com port and one of these activeX references.  Then allow it to stop the while loop.  Turn the LabVIEW out outside the loop so that once everything is cleaned, your application may close.  You probably want to wrap this command in a case structure so that if you are in the execution environment, it leaves your application.  But if you are in the development environment, you don't want to cause your LabVIEW environment stop.  Another thing is that right now, you actually have a race condition in the Exit event.  The com port will close first or LabVIEW will come out.  There is no defined order of execution.

  Alternatively, you can have an event to close panel? in this way, you haven't accidentally short circuit all your program by pressing the X key.  You want to capture this event, discard it.  And if you want to not actually closed, did trigger the Exit Program button so that you can gracefully shutdown.

• At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  original title: server and virus problem

  Hi SurajMendon,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Please post your question in the TechNet Windows XP Networking forum.

  Networking platform

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• Remote panels - Situation of the Client crashes

  Hello

  I would like to ask if someone can help me with the following situation.

  I have an application that has several other dialog boxes live and a high level VI this app is accessible by a remote client via remote panels. The highest level VI (contains the menu - structure of loop and event) the customer selects what he wants to run. Then, the front of his choice opens on his computer. Everything works ok.

  However, if the client computer suddenly loses internet connectivity, then the runtime indicate a crash of the plugin in the browser.

  On server side, all open applications appear to freeze. I can disable them one by one and then stop everything and try again.

  Could someone let me know how to address this issue? I wish that the customer, in the case where an accident occurs, to be able to reconnect to the application.

  Thank you and have a nice day.

  Hello

  Thank you to attach screenshots.

  The reason why you get this error is that you try to close a connection that is already closed by the server. You can add a simple error handler after your block of proximity with the Client , who must take care of the pop-up. There is possibility to ignore this error (or other). This knowledge base article does a great job explaining how.

  Please let me know if that answers your question.

• I need to restart the windows assessment services service to connect to localhost, whenever I start the client WAS

  A / installation ADK

  I need to restart the windows assessment services service to connect to localhost, whenever I start the client WAS

  Hello

  To improve assistance to this subject, you can ask your question in the technet forums.

  http://social.technet.Microsoft.com/forums/en-us/categories/

• How to remove a specific email inbox with the client application code?

  Hello

  How to remove a specific email inbox with the client application code?  Please suggest useful links.

  Advanced thanks.

  Concerning

  Sunil.G

  Your question is a bit broad, so it is difficult to give you details.

  First of all, you must have the ID of the original message. Usually, you get either by hanging the message when he came into the Inbox (by implementing FolderListener), or by retrieving a list of mail of enamel "Store".

  Once you have this message ID, you call Folder.deleteMessage ().

  Here, there is a laboratory of Developer:

  http://NA.BlackBerry.com/eng/developers/resources/Labs/listeningforemail.jsp

  Moreover, classes to look in the API of reference:

  Store

  Folder

  FolderEvent

  FolderListener

  Session

  ServiceConfiguration

  Message (message RIM, not the J2ME)

• j6410 over wifi is detected but not settled it on Win7 with the new installation of OJJ6400_Full_13.exe

  Dear all,

  I try to install my printer all in one HP Officejet J6410 (connected to an access point) wireless to my HP Pavilion dv5-1155eg laptop running Windows 7 Professional (ENG). I am trying to install using the new "HP Officejet Full Feature Software and Driver" (OJJ6400_Full_13.exe) for the specified printer. ""

  The rest of the HP software installation succeeded it. I am able to see the web interface of the printer from my browser. In the past, before the release of this new driver I could even print wirelessly, using the base driver provided by Win7.

  What fails is the installation of the printer itself:

  I use the software to 'Add a device' the HP that successfully locates my printer wireless in the screen "found network printers." I selects the printer, press 'Next', Network Diagnostics seems to run ok and then start the installation of the printer, it is firstly says 'printer detected... ". "but she eventually fails with the message:" printer setup is not complete - click Retry to try install again... blah blah. "

  To make richer information, I use a firewall of G Data Internet Security 2010 that I followed him and I can see that it is not blocking anything. I even tried installing with the firewall disabled, anyway...

  In addition, I tested my printer with HP Network Diagnostic Utility. The utility comes with all the information correctly (network configuration, configuration of the computer, HP printer running services, found wireless).

  Any help is appreciated to make it work because it's a major drawback, as you can understand...

  Thank you in advance...

  Thanks for the reply, but that was not the solution... As I mentioned earlier, I had tried in the first place without the firewall installation.

  But, I found a good solution to the problem, and because it might be useful to others I write it here:

  After the movie with the help of HP without success, I managed to find a workaround for the problem:

  1. I uninstalled everyhting about printer software/drivers & restarted windows.
  2. I installed the begin shape everything (the file I downloaded on the site of HP), using the USB option this time and not a wireless.
  3. RESTART WINDOWS (sucks bigtime - respect for unix/linux "reboot is for material changes!")
  4. After you have installed successfully with the USB cable, I chose the option 'Configure wireless settings' Installer extracted files resulting from the file I downloaded frrm the HP site (if after installation, the installer window is closed you will need to locate the extracted in your Temp folder files or just run the file again..). Just follow the instructions of the installer.
  5. This should make the thing! REBOOT (again) and you're ready to go!
  6. (OPTIONAL) For me, the installer actually worked at the last moment, where he stuck permanently. But that was ok, because it's stuck after you set up the printer and corresponding software. After some time, the installer came out with the usual submit an evaluation form. Just ignore it, reboot and everyhting should work. At least it did for me...

  See you soon

• Connection WI - FI keeps breaking with the Satellite Z930

  Hello

  I bought a new laptop of Toshiba Satellite Z930 in Windows 8.
  I connect using the WI - FI connectivity and it works.

  However, the connection maintained by decomposing each kind and then. And it's horrible because I use my laptop to connect to a VPN network and it freezes the computer. I'm sure that it is not related to the WI - FI, itself given that my other laptop or machines work perfectly. It is clearly linked to the Toshiba and probably the settings.

  Please help, thanks!

  Hello

  Have you tried to connect to another router Wlan / wireless LAN?
  The same problem appear with an another WLan encryption?
  Test it!

  Just for test: disable encryption of WLan and try to connect to open Wlan.

  One other point: you use Win 8.
  Here is a nice HowTo for Microsoft - Windows 8 VPN connect
  http://TechNet.Microsoft.com/en-us/library/jj613767.aspx

• The Sony Corporation Media Remote App works with the Bravia KDL50EX645

  Just bought the following:

  BRAVIA KDL50EX645

  Sony BDV E390 Home Theater

  I downloaded the app Remote from Sony Media (Android) both my RAZR and my Tablet and all 4 elements are connected wireless via my Belkin router. I can't get eith the phone or tablet to locate the TV or DVD player. The app does support not these two elements?

  Hi Ham,

  Welcome to the community of Sony!

  Media remote app is compatible with the BDVE390 Home Theater System. However, it is not compatible with KDL50EX645 TV. Make sure that the Home Theater system is connected to an active broadband Internet connection.

  Try to complete your registration by following the instructions mentioned on the technical support article below:

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C1020792

  Please indicate the solution as accepted, if you find this information useful.

  Thank you for your message.

• Connection Officejet 6100 to Wifi with the Mavericks

  I have Mac OS 10.9.2 (Mavericks) and have installed all available updates.  I just bought a HP Officejet 6100.  The configuration software supplied with the printer does not work on the Mavericks.  I can use the printer via USB, but have no idea how to do to connect the printer to my wifi network.  All the instructions I found point using the diskette supplied with the printer (not compatible with the Mavericks) or assume that I already connected the printer to my network wifi (which is the problem that I am trying to solve).

  I had HP products in the past and if it is connected to the network, but it supports WPS and has a touchscreen user interface.  This printer does not seem to be supported.  The wifi light just keeps blinking.

  I don't like on ePrint, etc..  I want just the printer connected to my wifi so I can print from any number of computers on this network.

  Help, please.

  Thank you

  It wasn't very nice, that we were just trying to help.  Don't tell you specifically that your router has WPS.

  On your printer, press and hold the button wireless for 3 seconds.  Within 2 minutes, press the the router WPS button.

  Wait about 2 minutes. If the printer connect successfully, the wireless light will stop blinking but stays on.

  From there, you can connect your printer on your Mac:

  -Go to System Preferences > print & Scan
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and then beside the dropdown 'Use', select the model of the printer (not AirPrint). Wait for the 'Add' button becomes available. Until it clicks.

• MCE IR remote stops working when connected via Remote Desktop Win7

  I recently added an IR remote for my computer to Windows 7 (32 bit Ultimate) that I use mainly for playback of mp3. The remote control is only an AVS Gear MG-IR01BK Windows Vista/Window7 MCE Remote control infrared works by attached USB "infrared transceiver eHome.  When I physically connect the machine IR remote works perfectly; as soon as I connect via remote IR Office stops responding.  I had to configure the Audio remotely to RDP to get this to work correctly, but I can't find any setting that controls in response to the infrared remote control.  My quest for answers has turned up nothing so far, someone has suggested?

  Thanks for the suggestion.  At thegreenbutton.com behavior that I have reported was confirmed by others (the MCE Remote control is a HID device, so is related to the "console"). VNC is a viable alternative to remote desktop. I ended up using TightVNC (RealVNC purchase required for support of Windows 7), and the infrared remote control continues to work when I access the machine via the VNC viewer.   I want to remote desktop could provide this capability, but at least I have a working with VNC solution.

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• CSA with the Client VPN and remote access

  Hello world!

  I have the folowing isue: I have to tune in to the CSA for a clinet it connects remote with VPN Client only. He should not be able to connect to any other network or lan or dial-up.

  No idea what the policy should change or tune?

  Thank you

  You can create an access network rule that depends on a State of the system. The State of the system can be defined to have a game of skill, which belongs to the range of VPN and the network access rule would declare that the client computer cannot act as a server on UDP/TCP ports when the State of the system is ensured.

  So, if the laptop is not connected to the VPN, it would not be able to act as a server for connections to all and will be locked out. You will need to create an exception for the IP address of the VPN server to your corporate offices and allow the CSA client opening these ports.

• Cannot connect to Horizon view Desktop with the persistent drive user's profile

  I install a new pool of funds to Horizon 6. This will serve to staff supervisor who need their same desktop computers every time that they connect. The pool is set for the linked clones, but with records of enduring for user profiles. I put the user profile to be stored on a disk, persisting in the wizard of the Horizon. The persistent drive is on users 'Z' drive.

  When I try to log in with one of the title, accounts, windows gives me this error:

  The user profile service service has no logon. User profile cannot be loaded.

  Is there something I need to change Active Directory / group policy? I've never dealt with before persistent disk systems. The VM OS is Windows 7 Pro x 64.

  It seems fitting that profile does not know that it is supposed to be created on the persistent drive when I try to log in.

  I discovered that I actually had the following GPO is applied at the level of the computer that kept player to be accessible.

  Access to the removable storage / system

  Policy	Setting	Comment
  All removable storage classes: deny access to all the	Activated
  All removable storage: allow direct access in the sessions remotely	People with disabilities
  CD and DVD: deny execute access	Activated
  CD and DVD: deny read access	Activated
  CD and DVD: deny write access	Activated
  Floppy drives: deny execute access	Activated
  Floppy drives: deny read access	Activated
  Floppy drives: deny write access	Activated
  Removable disks: deny execute access	Activated
  Removable disks: deny read access	Activated
  Removable disks: deny write access	Activated
  Tape drives: deny execute access	Activated
  Tape drives: deny read access	Activated
  Tape drives: deny write access	Activated
  WPD Devices: Deny read access	Activated
  WPD Devices: Deny write access	Activated