How to use the second network card physical to Virtual Machine?

Similar Questions

• How to add the second network card?

  A server (VMware ESX 4.1) works well with a network card. Since I want to add a virtual switch, I need to add another network card. So I inserted into a PCI slot and reboot ESX. But the ESX does not. I need to reinstall ESX to let him find this network adapter?

  Thank you very much for the help.

  The added network adapter is Gigabit PCI Desktop Adapter, D-Link DGE-528 t.

  I tried several model D-link years... None of this can work.

  Use a broadcom or Intel card (and listed in HCL).

  André

• Impossible to use the second NETWORK card on VM

  I'm under VMware Workstation9 and I'll put up a configuration 5.1 ESXi

  VM1 - Windows 2008 - acting as a DC and a NFS storage
  VM2 - ESXi 5.1

  I added a second NIC on VM1 and VM2 to IP storage but I can't PING vice versa

  IP address:
  VM1 - 198.168.150.10 SM: 255.255.255.0
  VM2 - 192.168.150.11 SM: 255.255.255.0

  VMnet2 is used for the management, no problem with this vmnet3 is used for storage traffic but no communication possible

  Any Suggestion?

  Check the response of jmattson to Re: operating system of the virtual machine attempted to activate the adapter Ethernet0 promiscuous mode. This is not allowed for security reasons. solves the problem.

  André

• How to use the second server virtual router?

  Hey guys. I have a basic configuration to the House. ISP-ISP-router and my host pc. I want to be able to separate my virtual network on my home network. I have a second cisco router (WRT320N). I also have two network cards integrated with my motherboard. Now, is it possible to use the secondary router for my virtual server for my test environment?

  So far, I connected the external port of the ISP router on the internal port of the router Cisco-for the basic configuration. I guess, I need to connect the secondary of my host network adapter to the router cisco-but then, I do not know how to configure vmware to use secondary nic as NIC default.

  Any help is appreciated.

  Thank you

  Right, I found the solution, but I thought I'd share it for people who do not know.

  Router installation as follows:

  ISP-router to Host (NIC_1) to the host (192.168.0.1) connectivity

  ISP-router-Cisco-router (Internet Port) (192.168.1.1)

  MUST be on different subnets

  Cisco-router to Host (NIC_2) (in the NIC_2 adapter properties, all checkboxes except VMware Bridge Protocol MUST be deselected HOST, so please use NIC_2)

  VMware, Virtual Network Editor, full of connection Type must be selected as MANUAL that points to your NIC_2

  AND

  the parameters of the Virtual Machine to the network card, ' Custom: specific Virtual Network ' should point to NIC_2.

  This will allow you to use your second NETWORK card for your virtual machine (but the MAC address will be assigned by VMware... does cause no problem at all)

  Your virtual, in my case, Windows Server 2008 R2 operating system, will be no connectivity until you assign a static TCP/IPv4 address.

  This will isolate your virtual network on your home network.

  I hope this helps the other.

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• Call "HostNetworkSystem.UpdateVirtualSwitch" for the error of the object when you attempt to add the second NETWORK card

  Hi there - first post here, so please be nice :-).

  We are just trying to place an ESX4.1 own deployment in our environment (no previous installation of VMWare) to our main office, using Dell M610 and blades blades M600 to what would become our DR - two sites site hosting VMS on Equallogic iSCSI SAN disks.

  I configured 4 of our blade M610 with ESX 4.1 successfully and they work very well.  These blades have double NIC onboard, and after the initial installation of ESX, I could go to the virtual switch and add in the second NIC like vmnic1 (because one had already been detected during installation).  This fine workd for 4 guests on the M610 blades.  However, I came today to make my first installation on one of the old M600 blades and I encountered a problem.

  Installation went without any problems and I was able to add the host in my vCenter.  I can change all the settings without problem (created the Port of VMKernal for my connection to SAN iSCSI etc, but as soon as I try to add in the second NETWORK card, he paused for a while, and then I get the following error message:)

  Call 'HostNetworkSystem.UpdateVirtualSwitch' of object 'networkSystem-56 "on vCenter Server"VCEN01." ournetwork.local"failed. (network name has been changed for post).  When this happens, it locks up again for several seconds, and when the system returns, I can no longer communicate with the ESX host (Observer of events in vCenter watch 'host is not responding' and I find that I can not ping the host unless I reboot it.)

  If anyone has any suggestions I would appreciate it that I don't want to proceed down to the line with our Installer if theres an underlying issue and I need to redo everything.

  Concerning

  EFIN.

  Do you get the same error when you try to add the network adapter by using the command line?

  1. esxcfg-vSwitch - L vmnic1 vSwitch0

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• How to get the driver network card and on the use of the PowerCLI firmware version?

  Hi all

  I would like to know if anyone can help me in sharing the PowerCLI script to list the server NETWORK card driver and the firmware version?

  Note: I use the HP Blade Server and it's manual ESX - CLI command output:

  	HP BL 465c G8
  	~ # ethtool-i vmnic0
  	pilot: be2net
  	version: 10.5.65.4
  	firmware version: 10.2.340.19
  	bus-info: 0000:04:00.0

  	HP BL 465c G7
  	~ # ethtool-i vmnic0
  	pilot: be2net
  	version: 10.2.293.0
  	firmware version: 4.9.416.7
  	bus-info: 0000:04:00.0

  Any kind of help would be greatly appreciated.

  Thank you.

  PowerCLI Version

  ----------------

  VMware vSphere PowerCLI 6.0 Release 2 build 3056836

  ---------------

  Component versions

  ---------------

  VMWare AutoDeploy PowerCLI component 6.0 build 2358282

  VMWare ImageBuilder PowerCLI component 6.0 build 2358282

  VMware vSphere PowerCLI component 6.0 build 3052101

  It works for you?

  $esxName = "MyEsx".

  $esxcli = get-EsxCli - VMHost $esxName

  $esxcli.network.nic.list () | %{

  $esxcli.network.nic.get ($_.) Name) |

  Select Name,

  @{N = "Driver"; E={$_. DriverInfo.Driver}},

  @{N = 'Version'; E={$_. DriverInfo.Version}},

  @{N = 'Firmware Version'; E={$_. DriverInfo.FirmwareVersion}}

  }

• CMS OVA, adding the second NETWORK card breaks the first NETWORK card

  I'm testing CMS 2.0 and when I try to add a second NETWORK card in VMware, he immediately interrupts the first network card.  As soon as the loading of the image, the first NIC fails.  Even if I disable iface b, it will allow all traffic where iface one.  If I stop the application, remove the NETWORK adapter and run it back again, it works very well to the iface one.

  I want to test the public face with box feature, but I can't if I can't add a second network card.

  How do you add the second network interface and interface you add?

  You should add 'VMXNET3' type if you use VMWare, if you chose something else, you invalidate your license, see section 3.3 of the virtualized CMS 2.0 Setup Guide for deployments.

  If you need assistance, you must move this thread to the section of telepresence of forums, where this device is actively discussed.  You can change your question and change the categories at the bottom of the page.

• How to use the second HARD drive of Satellite A210 - BP1 for mirroring

  Satellite A210-BP1 came with 2 HDD (160 GB).
  Now, I want to use the second hard drive mirrored the first, one that has Vista installed.
  This should be done without supervision and in real time - as a RAID 1.

  How can I do this?
  I also have Vista professional available and I would be willing to use 3rd party software as well.

  Thanks in advance for your answers.

  Hi Jan

  I doubt that this is possible
  Why? The point is that you need to use two hard drives in mirroring, RAID striping, mode etc technology
  Satellite A210 can't RAID. It s only a SATA controller without RAID capacity!

  Therefore, the final answer is; NO, it is not possible to use mirroring

  Concerning

• How to upgrade the wireless network card in Windows Vista

  Hello

  Please how can I update the wireless network card?

  Thanks for the help

  Hello

  I suggest you try the steps from the following link to update the wireless network card drivers.

  a. right click on the Start button and click on Device Manager.
  b. display all devices on one.
  c. right-click on the WLAN driver and click on Update.

  Display us the results, once you try the steps above.

• Satellite P20 S203: How can I use the wireless network card?

  Hello
  first - sorry for my English. I have toshiba P20 S203 (I know - old hardware).
  I read a few descriptions on this computer and I know that the model probably have wifi. I see on the left side of my laptop, but don't see it Win Xp Pro Sp2.
  How to turn on and connect to my lan wirreless?

  again sorry for my English...

  Hello

  As mentioned the laptop has no installed wireless network card, but you can improve with one compatible.
  The minPCI card has two cables; Brown and white.
  Usually the white cable be connected to the hand and Brown to the

• IMAQdx mind traffic on the second NETWORK card

  Hello!

  My system:

  -Labview 2011 SP1 with NO Vision and IMAQdx

  -Windows 7-32 bit

  -2 NICs (Intel Pro 1000)

  On a NIC (subnet: 192.168.0.x - Intel pro driver) a sick Ranger is connected. Store it works with Studio of sick Ranger or the Labview Toolkit Ranger.

  On the second NIC (subnet: 192.168.1.x - Realtek dreiver) a Vision of Basler GigE camera is connected. It works with the grun80 pylon Viewer and IMAQdx GigE functions in Labview.

  If I start the acquisition of two cameras using the Studio store and Basler pylon Viewer (no Labview) both cameras acquire images at high speed without any interference.

  If I use Studio Ranger or LV-store Toolkit for the Acquisition of store it works selection UNTIL I have start a Labview VI containing the screw IMAQdx to acquire images of the Basler camera. As soon as the VI performs stops Acquisition of Ranger and Ranger loses the connection.

  I guess the driver IMAQdx is somehow interfering with two network cards.

  Suggestions how to exclude one of the NICs of IMAQdx driver or can someone tell me what is happening on the network driver layer when loading of IMAQdx?

  The purpose of my request to LV, is that both cameras can be used at the same time!

  Thank you!

  Disable the identification of cams network solve the problem?  See also How to disable IMAQdx sending periodically a Ping 'discovery'.

• Cable connection part for good - once I started using the wireless NETWORK card!

  Hello

  I went although all people in support on this issue, but now I have no other choice than to ask all you people here!

  That is the problem. I have two computers with multiple network cards. One is a laptop computer with wireless Draft-N support and 10/100/1000 NIC onboard. The other is a desktop computer with an ASUS Wifi b/g edge and also dual GigE ports nVidia graphics card.

  Whenever I try to use network wired for internet or local network even cards use, it died on me. It is impossible to obtain an IP address from the router to use and is unable to communicate with anyone at all. Not even with my local network or even directly to the router (192.168.1.1). If I turn on the wireless card, it connects and everything is groovy (except that I lost my GigE connection to my local network, which is most important!).

  I havegone through the standard fare of cyclic power to the router and cable modem, reboot of my machines, etc. all the normal things, we are required to do.

  After some hassles with the support of Linksys to get them to send me a new WRT330N, I finally received a new WRT310N and it shows exactly the same problem! Wireless connections work fine, but as soon as I disable the WiFi and wired go, Windows XP gives me nothing else than a message "limited or no connectivity" and let me out of the network.

  This leads me to think it's some sort of network problem due to multiple MACs on the same host name. Does anyone know how to get around this problem?

  Thank you!

  Disable the firewall on the computer and then also try to connect the computer to the modem and check if the computer is able to connect.

• Satellite P70 - how to use the second HARD drive?

  I have recently bought a satellite P70 - A - 10 d.

  I see that there is no second location on hard disk, so I can install a second disk.
  You can see the second slot in this video http://www.youtube.com/watch?v=uW75IsuFeoY.

  But I can't understand how screed the disc.
  Do I need additional items for it or he'll be safe just plug the drive and leave it without screws?

  Hello

  If the second HARD drive bay contains the HARD drive connector, you can connect the HARD drive using the 2.5 HARD disk as [this | http://www.newmodeus.com/shop/images/TOS-X505%20sm.jpg] a

  Welcome them

• Re: How to use the second hard drive in Satellite A300?

  I got a second hand Satellite A300 which was to be thrown out due to a defective DVD.
  I fixed the DVD and have a perfect system.

  On opening the box, I discovered that there 2 x 250 GB hard drives. I checked CMOS and show the 2 drives. However, Vista displays only the a drive.

  Excuse my ignorance, but how do I access to the second drive?

  I have Satellite A300 with two hard drives and each HARD drive has another operating system. Both hard drives are recognized correctly.
  I put t know what the problem is here, but the two hard disks should be recognized automatically.
  Try to set the BIOS to default settings and check again.
  Try to start the check and install Microsoft bootable disk if the two hard disks are displayed in Setup.

  I just hope that there is not a hardware problem.