HP 8600 slow load paper in the tray

Similar Questions

• error to load paper in the tray of the printer

  Although I have a lot of paper in the tray of the printer, my hp c309g-m all-in-one printer screen tells me to load paper, that is, the clip from the sensor to the rear does not work (the one with the Green Strip of rubbery material about it, I guess.) I removed and put it back on a few times, thinking it was wrong set, but it didn't work.  I cleaned the rollers, etc., too.  I try to use the same types of paper, I used for a year without problem.

  I have half of my book printed and don't want to change printers because the quality is not exactly the same thing. so, I would BE ESTATIC IF someone COULD HELP me to SOLVE THIS PRINTER.

  Thank you very much

  You need to contact HP about whether a repair is possible.  It is a hardware problem, not a software problem, and you can do that in Windows can ignore this error.

• Message says: load the paper, but there the paper in the tray

  I have a Photosmart 7520, I tried to print today and received a message that says load paper in the paper tray. There is paper in the tray. I pulled it and reloaded it, I got the same message. I turned off the printer and turn it back on and tried again, once more, I got the same message. I use Windows 8.1 on a computer just purchased in February 2014. Any suggestions?

  Thank you

  Sue

  Hi Sue,

  Please try this document for some alignment and cleaning tips: an "out of paper" Message is displayed on the control panel and the all-in-one does no paper pick up

  If this does not work, because your printer is still under warranty, you can contact HP support at 1-800-474-6836 North America or find the local for your country here phone number: http://welcome.hp.com/country/w1/en/support.html please look for the category 'technical support after you buy '.

  Hope that helps

• HP ENVY 7640 all-in-one: print envelopes and its telling me to load paper into the photo tray

  I am trying to print envelopes on the HP ENVY 7640 printer and it tells me to load paper into the photo tray. Have you encountered this problem and how to solve? Thank you.

  Hey @cmm3,

  Welcome to the Forums of HP Support!

  I understand that you have a problem when printing envelopes from your Windows 7 computer to your HP ENVY 7640 e-all-in-one printer. I would like to help you today with correct this print error "Photo tray". To start I have to make sure that the envelope is correctly loaded in your troubleshooting paper tray. Once you have confirmed that your envelope is loaded OK we'll take a look at the envelope to print on your computer settings. Can I please you follow the steps below.

  Step 1: Load the paper:

  To begin troubleshooting, please click here. Once the support document opens, please select the drop down list for "load envelopes. Please see the instructions on the screen to ensure that your envelope is correctly loaded in the paper tray. Once you have confirmed that your envelope is loaded correctly, proceed to the next step.

  Step 2: Check the print settings:

  Below I will provide you with instructions for printing envelopes per word. You should use a different program on your computer to print envelopes, please respond to this post with the program that you are using so I can provide specific measures.

  1. Open Word and click mail merge to top
  2. Select "envelopes" in the upper left side
  3. A page of envelopes and labels should now open. Enter your delivery and return address.
  4. Select 'Options' on the lower right
  5. Under the tab 'Options for envelopes' to ensure that your envelope is correctly selected.
  6. Select the 'Print Options' tab at the top. You must now select as appropriate feeding method for your product.
  7. Make sure that you choose the option "Face down".
  8. Also ensure that 'right-hand Rotation' is selected
  9. At the bottom of the window, select the drop-down list of pet food
  10. Make sure that the feeding method is set to main tray rather then select automatically
  11. Press 'OK' and 'Print'.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HP Photosmart more B210e - no more paper - load paper into the main tray

  
  

  Hey fanblade,.

  Thanks for the detailed post describing the problem you are experiencing.  Looks like that paper inside the printer sensors have a problem with the detection of the paper in the tray.  This may be due to rollers be dirty and unable to take the book, settings problem or possibly an electrical problem in the unit.  I recommend the steps in the document below.

  "Out of paper" Error Message and the printer is not looking upwards or the paper feed

  I would like to know how it goes as I steps to perform a factory reset on this printer,

  Jason

• ON PAPER MESSAGEDU MY C510 SAME HP IF THERE IS ENOUGH PAPER IN THE TRAY, PLEASE HELP.

  ON PAPER MESSAGEDU MY C510 SAME HP IF THERE IS ENOUGH PAPER IN THE TRAY, PLEASE HELP.

  We recommend that you reset your C510 HP first. You can perform the reset by following the steps below:

  1. press the "Power button" to activate the product.

  2. with the product, unplug the power cord from the back of the product.

  3. disconnect the power cord from the wall outlet.

  4. wait at least 15 seconds.

  5. plug the power cord into the wall jack.

  6. reconnect the power cord to the back of the product.

  7. If the product does not light by itself, press the Power button to turn it on.

  Once done, print a self-test report by following the next steps:

  1 load plain white paper in the input tray.

  2. from the home screen on the control panel of the product, click "Menu" on the upper left side. A list of menu options screens. 3. click on "Settings" and then click on 'tools '. The maintenance of the printer menu displays.

  4. in the maintenance of the printer menu, click "Printer Status Report". The product prints the report.

  If the report is printed correctly, try again to print your original document.

  If the problem persists, you may need to check the status of documents in the status bar. To do this, follow these steps:

  1. remove the stack of paper from the status bar.

  2. check that the obstacles within the status bar. A flashlight to view the mechanism inside the status bar to make sure that nothing is blocking the paper to engage with the rollers. Even small pieces of paper can cause paper feeding problems. (Important: If any obstruction is detected in the paper path, you need to refer to "Cleaning the rollers" segment at http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02248120-20%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken)

  3. to review the status of the paper and then replace any paper torn, dusty, curled, wrinkled, or bent.

  4. ensure that all the papers in the stack are the same size and type. Never charge which coexist types of paper in the tray. The product can only process one type of paper at a time.

  5. press on the stack of paper on a flat surface to align the edges.

  6. make sure that the paper stack does not contain less than 10 and not more than 25 sheets paper.

  (Note: the limitation of the number of documents applies only during the phase of solving problems.) Once the problem is resolved, you can load the tray to its original capacity).

  Once you have checked the status of documents, reload the tray in the following way:

  1. lift output in open position and open the door of the feeder.

  2. slide the width guide to its outermost position paper.

  3. Insert the stack of paper into the paper tray with the short edge forward and the print down side.

  4. adjust the paper width guide so that it rests against the stack of paper.

  5. lower the output tray, and then close the tray door. Once this is done, print again an automatic test report by following the above steps. If this too does not resolve the issue, refer to some more solutions at HP support center link below: http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02248120-20%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  GuruAid.com

• I have a HP photosmart printer. I have problems printing of documents. I get a message that I have more paper. However, there are paper and the tray is installed properly. What can I do?

  I have a printer HP photosmart Plus B209. my pc is communicating with my printer but the printer will not print because it repeats me more paper. However, the tray is properly installed and loaded paper. I unplugged my printer and plugged back in nothing works. All boards

  Hello

  1. What is the full/exact error message?

  2. who is the operating system installed on the computer?

  A supply of paper problem can occur for several reasons, such as rolls of papers dusty or contaminated, the condition of the paper in the tray, or even problems with the software.

  You can run the troubleshooter and check.

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Note: You can change the operating system that is appropriate in the article.

  See also the steps from HP article:

  HP Photosmart Plus (B209a, B209c and B209b) all-in-one printers - all-in-one not picking up or feeding of the paper in the Photo tray

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=110&prodSeriesId=3777155&prodTypeId=18972&ObjectID=c02156652

  Hope this information helps. Response with status so that we can help you.

• The printer message ' load paper in the printer "appears when the paper is still in the status bar.

  I rebooted the paper in the tray several times, and the message still appears. I have tried rebooting printer several times and the message to load paper continue to appear.

  jmtbat

  Please read this post then provide some details.  What printer model?

• HP photosmart D110a: printer says paper but leaves a black mark on paper in the tray

  Laptop got hit out of the office by CAT when you are connected to the printer when printing. Now the printer says there is no paper in the tray and it leaves a black on the paper mark as the printer attempts to shoot the top sheet of paper in, but he can't.

  I fixed that on my own by giving the top sheet a little bit as he began to print. Hope this helps someone.

• DeskJet 3745 cannot detect the paper in the tray

  I recently bought a HP DeskJet 3745 at a yard sale. No problem installing on my Windows 7 desktop.

  However, when I try to print to the printer will not do. He says he's paper (even if there is paper in the tray).

  My guess is that something is wrong with the paper sensor (or switch). I could clean up if I knew what I was looking for, but I don't see anything that could be the sensor of paper. I tried to search the description of the part online and found a site selling a "branch ADF" that meets the description of the probe, but it doesn't have a picture.

  Suggestions for what is the sensor or how to solve this problem would be greatly appreciated. I'm not afraid to have to disassemble the printer, if necessary.

  Okay, I found the problem. After that several futile attempts to print, the paper that was in the tray has a black slick spot used a roller running on top of it. The roller needed cleaning. It's the only roll that lies under the main mechanism and it is difficult to go to the. Once I cleaned it, the printer works fine.

  There is no paper sensor, the roller pulls just the paper in ink jet Assembly, which has a trigger switch. The only switch is used to detect paper jams, but also lack of paper in the tray (assuming that the roll is clean).

• With no paper in the tray, the printer has no error light. As soon thre is paper in the printer, I get error lights.

  Original title: what a printer problem.

  When no paper in the tray, my HP PSC 1400 no flash no lights error, however when the cartridge is mounted on the inside, it flashes error lights. As a result, I can't take a printout and I feel buried in the huge pile of unfinished work. The window so that HP behave as if they have nothing to do with it or the problem is bigger than their power; Well, I don't have to go, but to spread my shirt in front of you as if I'm begging!

  Contact HP support or post in the forums.
  What is your shirt has to do with it?

• Printer DELL3115cnB328 FC - Says PS in paper when there is paper in the tray, how to fix?

  Printer DELL3115cnB328 FC - Says PS in paper when there is paper in the tray, how to fix?

  Contact the Dell printer support. It is highly unlikely that there is a Microsoft fix for your problem...

  http://support.Dell.com/support/index.aspx?c=CA&l=en&s=Gen

• Error message 4 HP on PC paper\ \'out L', the paper in the tray

  My HP 4 L was working fine but now an error message on my PC shows "printer paper".

  Paper in the tray and inserted correctly checked paper tray, no document showing of lights and a test print when pressed high butten.

  Any ideas please?

  Hi BazzaofWatford,

  Glad to hear that you got the problem solved. Have a wonderful day.

• Photosmart D7560 do not print envelopes-> load paper into the main tray

  My photosmart D7560 h will not print envelopes, after having moved the envelope position for printing, the message "loading the paper in the main tray is displayed.  It prints correctly the data of envelope on a sheet of paper 8.5 x 11.  The Setup is for a #10 envelope.  Envelopes are self-sealing.  I tried to crease the edge better but that did not help.  I tried a non-self seal (who had a top letterhead so I couldn't use it for this shipment) and he worked.  Is it possible to do self seal envelopes work in this printer?

  You have the flap folded inside the envelope, so that it does not stick?

• More OfficeJet Pro 8600: picture difficulty of paper in the tray

  For the first time, I am trying to print a photo of my MacBook Pro/iPhoto with photo paper glossy premium, brilliant.  The printer has difficulties to enter/loading paper.  I had to gently push the paper the printer to enter and print the photo.  The photo is very after several tests.   Any suggestion would be appreciated.    Thanks in advance

  Hi Anna,.

  Welcome to the Community Forum of HP.

  I don't have Mac - that will be obvious when you read the answer - I think the "fix" implies a simple adjustment on the Type of media in the choice of paper.

  The question with the answer to my find a way to illustrate the point - the following is the help file a competitor - their files are well written, as always; This file shows where to find and set the media Type setting.

  Driver / software settings

  Comment

  You must set the media type is as close to your type of paper as possible.  The point is to allow the printer to wait 'thick' or thin paper, glossy or matte finish, etc.

  The printer will answer by setting rollers to correct spacing, setting the ink to the paper type and the definition of the duration of drying.

  I hope this helps.

  Click on the Thumbs - Up Kudos to show that you appreciate the help.

  I am happy to provide assistance on behalf of HP. I do not work for HP.

  Click on accept as Solution when the answer provides a fix or a workaround!