HP ENVY 15: WiDi on Windows 10 gives black screen.

Similar Questions

• Start normal mode after windows xp bar charge it gives black screen and in safe mode it gives blue screen

  Victorinox original title: Black scree & blue screen...

  So my laptop that is running Windows xp, start in normal mode after windows xp bar charge it gives black screen and it stays like this, and in safe mode it gives blue screen, what can I do? I need your help atleast to save the files to my hard drive...

  Hello

  · What is the error code or error message that you receive when the computer starts in safe mode?

  · Were there any changes made on the computer before the show?

  · What is the number and the model of the computer?

  · Who is the service pack installed?

  Try the methods below:

  Method 1: Disconnect all the devices connected to the computer such as printers, scanners or USB hard drives and restart the computer and check if that helps.

  Method 2:

  Try to start your computer in last known good configuration. You can check the link for the procedure: how to start your computer by using last good known Windows XP Configuration: http://support.microsoft.com/kb/307852

  Method 3:

  You can follow the steps listed in the link: after the Windows Logo appears, or after you log on Windows, a Windows XP computer can display the wallpaper, a black screen or a blue screen: http://support.microsoft.com/kb/318027

• Windows 7 Pro black screen with cursor on all modes and no login screen

  OK so basically, it's how, my laptop decided to me-screw right when I need to make some adjustments to my final project for next week.

  Friday he started very well in class and at the end of the course at 6:30, I stopped him. I normally don't that often stopped because I usually find myself opening upward in an hour later. But I did this time and when I got home and turned on around 9:00, it started like this:

  Screen Compaq PhoenixBIOS > Windows boot animation > black screen with cursor mobile, no login screen

  No screen connection. No sound. Not nothing but a black screen and the cursor movement. So I force shutdown and turned it back, this time he asked a chkdsk and I ran it. A ton of stuff file unreadable came and it took all night to run through it all. Tried to start again and Windows Error Recovery came and I tried all Modes of security and start normally and all produce the same black screen and the cursor with no login screen.

  Then I used my Windows 7 dvd repair to try and system restore to a week before. That's where I noticed that windows had installed a critical update at 12:00 on Friday. Tried to restore before that, but he failed. Gave me an error 0 x 80070057 and said I should run chkdsk /r and then try again. Then I used the cmd prompt through dvd repair and he has seen all these things wrong file again once recovered things then realized hours later. Tried to restore the system again. Still the same error. A run chkdsk again through the cmd prompt, then he went to clean without errors or orphaned files or anything, but it took a lot of time. I used the Startup Repair, and he has not found anything wrong either. But still the same error the system restore.

  So I looked around online for the last two days, trying to figure out and that someone said to try CTRL + Alt + Delete, the sticky shift key thing. So I tried to boot the system again, same black screen with cursor movement. I did CTRL + Alt + Delete, nothing. Press and hold the SHIFT key, and a pop-up window asked FilterKeys. Press the SHIFT key 5 times, a popup asked about sticky keys. But that's all I can get it to do. Nothing else. I tried to boot into safe mode with F8, chose, each of them and that changes in screen resolution and the words "safe mode" in all the corners of the screen. If the repair dvd's while I start in safe mode, it will open as well in safe mode, but with the same black background mode. Tried running sfc/scannow through repair invites cmd of the dvd and it says a system repair is pending and he had to restart, and then run the sfc/scannow. Tried, but it doesn't do anything when I restart except go to Windows Error Recovery asking either start in any safe mode or normally. And then it's just black screen again.

  So I am at a complete loss what to do now. After all of this mess, it seems that this Windows Update Friday afternoon did something and when I booted it upward once again, his cause nothing but problems. I think it has something to do with the display and the graphics card drivers? It's as if the thing starts but I do not see anything either because the sticky keys appears, but sees nothing else, no matter what I do. Seriously, I don't want to this junk because this is a new hard drive and I was just able to retrieve my files from my old hard drive that had epic failures as well. And I just got this new specifications I wanted as well.

  Laptop Spec:

  Compaq CQ50-115nr
  OS: Windows 7 Professional
  HARD drive: Western Digital Scorpio Blue 320 GB SATA WD3200BEVT
  Processor: AMD Turion X 2 RM-70
  Graphics card: NVIDIA GeForce 8200 M G
  Memory: 3 GB RAM

  If someone could seriously help me I would be VERY happy.

  Hello

  This isn't good news.

  --------------------

  STOP: 0XC000021A

  Can be a difficult problem to solve, and you indeed need a technical help in a real store of the computer
  (not the leeks and the glances at a BestBuy or other BigBox stores) or system manufacturer support.

  Cause

  This error occurs when a subsystem of mode user, such as WinLogon or the Client Server Run-Time Subsystem (CSRSS), irremediably compromised and security can not be guaranteed. In response, the operating system goes into kernel mode. Microsoft Windows cannot run without WinLogon or CSRSS. Therefore, it is one of the rare cases where the failure of a user mode service can stop the system.

  Incompatible system files can also cause this error. This can happen if you restored your hard disk from a backup. Some backup programs may skip restoring system files which they determine are in use.

  Solve the problem

  Run the kernel debugger is not useful in this situation because the error occurred in a user mode process.

  Resolve an error in the user-mode device driver or system, third-party application service: Because the bug 0xC000021A control occurs in a user mode process, the most common culprits are third-party applications. If the error occurred after the installation of the new or updated device driver or service system, third-party applications, the new software should be removed or disabled. Contact the manufacturer of the software on a possible update.

  If the error occurs during the system startup, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time. If the error is not resolved, try to manually remove the offending software. If the system partition is formatted with the (FAT) file allocation table, use a MS-DOS boot disk to access the hard disk of the computer. If the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or remove the defective software. If the defective software is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file. If a room newly installed if material is suspected, remove it to see if that fixes the problem.

  Try running the emergency recovery disk (ERD) and allow the system to repair any errors that it detects.

  Solve a problem of file system do not match: If you have recently restored your hard disk from a backup, check if there is an updated version of the backup/restore program available from the manufacturer. Make sure that the latest Windows Service Pack is installed.

  STOP: 0XC000021A<-- read="" this="">
  * 1314.html http://www.faultwire.com/solutions-fatal_error/Status-System-Process-terminated-0xC000021A-

  -----------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  It's my generic bluescreen convenience store - you can try Mode safe mode as suggested in article
  above - repeatedly press F8 that you start. Disks of Vista are probably necessary - if you do not try to repair it, you can borrow a friends because they are not protected against copying. You can also buy the physical disks
  good system machine cheap that you already own Windows (you have to reinstall them if)
  required). You can also repair disks on another computer.

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  Displays information on all the "crash" of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Windows Resume Loader black screen on HP Pavilion dv4-2145 dx laptop Windows 7

  I have a HP Pavilion dv4-2145 dx laptop with Windows 7. After pressing the button "on", the logo operation windows says its "recovery" windows, but a black screen titled "Windows Resume Loader" appears with the following message:

  The last attempt to resume the system from its previous location failed. Attempt to resume again?

  With the 2 following options:

  1. continue with system summary, (which does not work and I end up with the resumption of the "Windows" followed a blank black screen...)

  2 Delete restoration data and proceed to system boot menu (I haven't ' truei stops because I wasn't sure what that meant)

  But I managed to go to the reviews section diagnostic systems and it seems that he pass all 5 of the test, including hard drive and memory, poster, etc. So I don't know what the problem...

  Please notify.

  Thank you very much!

  Hello

  I think that in this case, you will have to choose the second option - "Delete restoration data and proceed to system boot menu" and see if that fixes the problem.  If all etc. documents you had open before hibernation were saved, then you should not lose anything.  If there are unsaved changes (for example if you have added to a document), the file will be to the point that his last record and you lose additional data.

  Kind regards

  DP - K

• Windows load with black screen and does not start after windows updates

  Original title: load windows normally screen will not continue

  I went to my computer tower and I chose to install updates when closing.  I went back later to re - turn on my computer and now it loads to the top of the black screen that gives you 5 options. safe mode, safe mode with networking safe mode command prompt, windows loads normally and finally to load windows from last known configuration that works.  Problem is that none of these options work.  they all return me to the same screen.  Help this laptop came preloaded with Win XP Media Center edition and I can't get back to work.  IM assuming I need a XP disk support center but I can't find them anywhere! HELP PLEASE SOMEONE!

  Hi Burton089,

  Your hypothesis is right. To resolve this problem, we need to repair your installation of Windows using the Windows XP disk. We recommend that you contact the manufacturer of the laptop to check if they have the Windows recovery disk.
  See perform a repair Installation
  

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Portege 7220 and windows 98. Black screen installation

  Hello

  I am facing this problem when I try to install win98 on the machine above Portege 7220 (/ PIII650/64/12/13 t/M), following on its docking station...

  I boot from a floppy disk and cd rom (e:\) access in order to run the installer of windows 98SE. Once I typed e:\setup.exe I get a black screen and the computer crashes. However I can install windows NT or 2000 on this machine, and also the windows 98SE cd works ok on other computers, i.e. no black screen!

  No idea what is the problem?

  Thanks in advance,
  Bar

  Hi Bar

  Please do not be angry on me, but I have to ask you something. Did you use Win98SE full version or simply update CD for Win98?

  It may be that your CD is scratched! Then please try another new CD or another OS as W2k!

• Windows Server 2008 black screen

  I am using Windows Server 2008.  Recently, the machine starts to a black screen until I could never connect.  All I see is a black screen and a mouse pointer.  In any case, I tried to run sfc/scannow from the command prompt and I get a message that says "there is a system repair pending which requires the restart ends.»  Restart windows, and then run sfc' problem is, it does not restart, and it does not run sfc period.  Is there a way to kill this scan assumed already running?

  Also, I wonder if there are any other ideas about how I could proceed to fix the black screen?

  I loaded the software that was supposed to be a package of OPC server.  When I did, others were more able to RDP to the server.  They got the black screen.  Not have never seen one before, I decided to try to restart to solve the problem.  It now boots directly ot the black screen, windows does not load and won't do anything beyond.  Any help would be very happy.

  Windows Server people hang out here:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Windows XP Home, black screen after loading screen (seemingly unique problem)

  Hi all

  I am trying to upgrade to service pack 3 Windows XP home on my old computer from eMachines T2838 and experiences a @# *! a time to do it. This is the third time in 2 days I had to wipe my HD and re - install XP, because of some problem installing updates which has damaged the operating system.

  Here's my current situation.

  Yesterday, after the failure of the HD for the second time (computer got stuck "performing cleanup" on SP2, forced a reboot, got a restart loop after, would not load Windows) I installed XP, update to SP2, then downloaded the service pack real itself. He has installed fine and asked me to restart.  I respected that, and the computer restarted. As soon as the "Loading" screen popped up, I knew that something had gone wrong.  When I started on the desk, I was stuck in 640 x 480 w / 4 - bit color graphics mode. Could not be set. So, I thought, okay, let me reboot Windows and see if he "rediscovered" the integrated video card. Well, I restarted, and the "loading screen jumped into the appropriate color mode / resolution, so I thought that I was in the green."  Well, after that, all I get is a black screen. No message 'No signal!' or anything like that.  Even tried a few instructors that I have. Looked around online, has seen the references to "Last known good Configuration" 'safe Mode' etc etc.

  I tried all the options on the list of F8. Either she freezes at Mup.sys xxxxxx or boots up to the loading screen and then goes black after. I can hear the HDD does it's thing for a bit, so I don't know it is loading this screen "check to activate the automatic updates" which appears after SP2 is installed, but I can't.

  Use the recovery console, (did the repair option the first time after it kept restarting, Windows took 5 minutes to start an IE6 get locked every opening, so had to wipe and re-install) typed "chkdsk/p/r" and he did his thing for about 30 minutes, rebooted and still have the same problem.

  I don't know what else to do. I REALLY want to redo everything this a fourth time, only to to have screw it up once again, and I don't know how many times I can use the key I have on the back of the computer.  (Using a retail disk and an OEM key, Finder product key changer.) -A Microsoft Support Officer showed me that one. Quite handy.

  People do you have any suggestions?  I would really appreciate it.

  Hello

  Try the steps listed in the link below and check if it will help: computer stops responding with a black screen when you start Windows XP: http://support.microsoft.com/kb/314503

• Windows startup at black screen after the Windows logo

  Original title: Evga Nvidia GeForce GT 520 1GB black screen graphics card

  I have a Hp Pavilion 6400 in the series which ran on Windows Vista (32 bit). I recently installed Windows 7 Ultimate (32 bit) and now the screen goes black once the windows logo closed its animation. I uninstalled the driver, re the driver installed and configured my system to the lowest resolution.

  Already found in the forums.
  -TV is too old to be compatible.
  EVGA - technician told me that the food was not powerful enough.
  -Forum Windows says: error in Explorer.exe.
  -Also found response that runs the computer through MSconfig would solve the problem.
  So far, none of these solutions have worked. Answers appreciated.

  Problem solved.

  It turns out, the driver for the video card would never completely install due to its mode of operation.
  Solution.
  1 restart Windows "low resolution".
  2. access to the form of previously downloaded files driver install the EVGA site while in safe mode.
  3. once divers have installed I changed the resolution in a HD rather than a framework
  "(native)" parameter in the resolution section.
  4. application of the Windows updates.
  5A started playing Star Trek Online.
  Thanks for your reply and have a great week.

• Windows does not, black screen

  My loptop does not load windows its all Blacks some 1 help me

  Original title: error windows 7

  My loptop does not load windows its all Blacks some 1 help me

  Hello

  Do you get a splash screen at startup (Logo of the manufacturer of the motherboard or computer, etc.) or it still not completely black power on?

  If there is absolutely nothing on the screen to power on, contact the manufacturer if under warranty.

  If it is not under warranty, contact a good computer repair workshop, local and reputable.

  If you get something on the screen to explain what it is.

  See you soon.

• Windows displays a black screen with cursor after the installation of updates

  I leave the official updates of Microsoft doing their thing last night before closing and I woke up today to see a black screen greeting me after that I entered my password on the start screen. The only thing that appears is HP Coolsense. No program, no nothing. It's just a wonderful black screen. The world how this issue fixed?

  Hello bean,.

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver. I suggest you to update the display driver of

  your computer and check if it helps. Please follow these steps:

  a. press the keys Ctrl + Alt + Delete , and then click Task Manager.

  b. click on 'file' and then click on "new task".

  (c) in the immediate window, type explorer.exe , and then click on ok.

  d. Office should appear. Otherwise, in the immediate window, type devmgmt.msc , and then click on ok.

  e. the device manager should open.

  f. expand 'graphics', right click on the display device, click "Update driver software", and

  Follow the on-screen instructions.

  After update display driver, you can correct the screen resolution using the following steps:

  a. right click on the desktop, and then click screen resolution.

  b. in the 'resolution', select the recommended resolution.

  c. click apply and ok.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Satellite C70 - A - upgrade Windows caused 10 black screen

  Hi all
  I have a Toshiba Satellite C 70 and have recently upgraded to Windows 10. It went well

  , but the next update caused my screen to go empty.

  I checked all the equipment and materials - all OK.

  I have downgraded to Windows 8.1 - no change

  Having hooked up to an external monitor (my TV) - hey all presto, it's here.

  I have reset to factory settings - no change.

  I updated the Intel graphics driver - no change.

  I checked for Lucid MVU - not installed.

  I've updated the video driver - no change.

  I checked the brightness, etc-all good.

  It is common to the screen image (not even safe mode, or a mouse) on the laptop screen.

  I searched forums after forums, but without success. Please can someone advise if this is fixable and if so, how?

  Thanks in advance

  Posted by mazudazuk
  

  Hi all
  I have a Toshiba Satellite C 70 and have recently upgraded to Windows 10. It went well

  , but the next update caused my screen to go empty.

  I checked everything all right.

  I downgraded to Windows 8.1 no change

  After connecting to an external monitor (my TV) hey presto it s all what he.

  I have reset to factory without changing settings.

  I updated the Intel graphics driver without change.

  I checked for Lucid MVU not installed.

  I've updated the video driver no change.

  I checked the brightness, etc. all good.

  It is common to the screen image (not even safe mode, or a mouse) on the laptop screen.

  I searched forums after forums, but without success. Please can someone advise if this is fixable and if so, how?

  Thanks in advance

  Same here - works well only on attached VGA monitor.

• Lenovo Ideapad Y700 17.3 ", Windows 10. Black screen after hibernation

  I use Windows 10, and it is updated. When I put my computer in hibernation, sometimes the screen is black when I start the pc again. Only solution is to reboot the pc. Is this a known issue? How can I fix it?

  Well, there are several questions about it. Suggesting the audio driver, the driver vga intel, but for me the key was reinstall all drivers with "intel" in their name

• NFS Carbon does not start in Windows XP a black screen and hangs

  NFS Carbon
  Carbon NFS does not work under windows xp... freezes and the screen shows black! Please help someone...

  Hi VikasSinghXV,
   
  Try to update the graphics card drivers by visiting the manufacturer's website and see if it improves the situation.
   

  See this link for more information on the update of drivers:

  How to manage devices in Windows XP

• I have problem starting (windows 7) without black screen

  I installed windows 7 on my laptop (which supports windows 7), 2 years ago. 1 year, I installed a game on that laptop, my laptop was ok. A few months ago, I opened my computer and this happened to me: (check the picture in the link. All my shortcuts in my home page are white, sometimes they still do not appear, the windows key is white, I can't open, install any programs, unless I run it in safe mode, or make the system restore). I start in safe mode, I deleted the game and my laptop had no problems starting. I opened my computer 3 days ago, he had the same problem again and this time, my shortcuts are not yet available in my home page. If I do the system restore, it will be ok, but when I disable it, it will happen the same problem. I tried startup repair, but it cannot detect all problems.

  I had 2, the two 90 GB HDD, 1 is empty, the other is half empty (45 GB), my RAM is 4 GB, it uses only 3 GB, recently spent 2 to 4 GB RAM.
  Is there a way get fix this, without a format?
  http://ImageShack.us/photo/my-images/16/90522409.PNG/

  I did not install Kaspersky Anti-virus. TDDSKiller is just a small Kaspersky utility designed to search for infections of rootkit that is the worst piece of infection right now. Your computer might be infected with one.

  (In addition, repeat steps 2) and 3).
  If they don't work, then perform a new installation of your windows.
  Good luck!