HP laptop PC 2000 is hanged I press the power on button product ID is E3B41PA #ABG

Hello. I am facing a problem is that when I turn on my laptop, it crashes and don't show any type of display and bright keyboards are on. After 8.9 tent the sytem starts up properly but after 15 or 20 minutes it restarts again and again.
I run HP PC Hardware diagnosis UEFI and it gives me a failure message with ID 0U097F-6MV766-MFGJXG - 03 404c failure
the test of the system

Any help please!

Hi Awaislftikhar,

The next step to replace the memory. The link I provided in my last post will give you consistent references.

Thank you

Tags: Notebooks

Similar Questions

  • Dell Latitude E6400 does not start pressing the power instead button, I have to remove the battery.

    Original title: problem starting Latitude E6400 lappie

    Hi all

    When I start my dell latitude6400 is not start pressing the power instead button I have to remove the battery to the rear and place it again, and then the lappie starts... someone can help to...
    Thank you

    Hello

    1. what happens when you start the laptop, you receive no error message?

    2 have you made any changes to the computer before the show?

    I suggest to remove the battery and connect the laptop to AC power and then try to start the computer to see if the problem is with the battery.

    I suggest you to contact Dell support on the issue, as this can be a hardware problem.

    http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&l=en&s=DHS&CS=19

  • My his laptop makes a beep when I press the power button / stop and it does not start

    Hello

    I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

    -Mayur gala

    Hi Mayur,

    Welcome to the community,

    Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

    See the table below which shows the beep codes and the possible problem:

    Overview of beep Code
    Beeps Description Possible cause
    1 ROM BIOS checksum failure The map system, covers BIOS corruption or errors ROM failure
    2 No memory (RAM) detected Memory or memory slot failure
    3
    • Chipset error (North and South Bridge error)
    • Time-Of-Day Clock test failure
    • Gate A20 failure
    • Super i/o chip failure
    • Keyboard controller failure
    System board failure
    4 Memory read / write failure Memory failure
    5 Real Time Clock (RTC) power failure CMOS battery failure
    6 Video BIOS Video/smart card failure
    7 Failure of the CPU Processor failure
    8 LCD SCREEN Failure of the LCD

    Let me know if you need assistance.

    Thank you

  • Pavilion 15, G8D9OPA #ACJ: my laptop does not turn on after pressing the power button

    HII, after a week that I have on my computer hp laptop 11 months but its not get. I even removed the battery and tried to get by pluging the adapter, but it doesn't work. What I would do. Please help me.

    Hi @Swati_20,

    Welcome to the HP Forums!

    It's a great place to find answers and advice!

    You have the best experience in the HP forum, I would like to draw your attention to the HP Guide's Forums:

    Learn how to post and much more.

    I understand that your Pavilion laptop not turn on.

    When I did a search with the product number, you provided I have no results.  Would you be kind enough to verify this information.

    How can I find my model number or product number?

    What operating system do you use?

    When you connect it to the power light on the power supply?

    Here is a link to the HP laptops - tests and using the AC adapter that can help.

    You can also try a hard reset.   HP - notebook computers use the hard reset to solve software and hardware problems

    Please keep me updated.

    Good luck!

    Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as yourself. Please consider tagging the post in order to resolve your problem as " ""Accept as Solution"" " to help other members of the community!

    To show the appreciation for my efforts, please click the 'Thumbs UP' icon' below.

  • Compaq v3000: need to press the power on button repeatedly

    Hello

    My compaq must support the switch several times, and lengthwise, press. Sometimes, but sometimes not. im not using batery because it totally dead, so im used directly to adapter charger.please help to understand

    Hi @sitimariam,

    Welcome to the HP Forum!

    It is a wonderful location to converse with the community, get help and advice. You have a rewarding experience, I would include the following link for your perusal and reference. First time here? Learn how to publish and more

    I understand that it becomes difficult to turn on your laptop. Currently, you have to press on and press and hold power for long periods and several times before it will fit.

    First of all, we exclude the adapter as a cause.  HP laptops - tests and using the power adapter AC. Are you connected directly to an electrical outlet or by using a power bar? Have you tried different outlets?

    When you connect the AC adapter to the laptop, you see a led to indicate the port will be able to?  What is the power port appear loose? You can also try to clean your laptop. It is possible that dust makes it difficult to connect.  HP Notebook PC - cleaning your laptop PC.  Once you have started, you see error messages or have other questions?

    Please let me know the results.

    To help visitors and members to find solutions that have helped others, please consider choosing "accepted Solution" " " on the post that solves your trouble. " This will give it more visibility and make it easier to find.  "Please consider clicking on the" ""Thumbs Up Icon " below to say thank you for you help.

  • Tecra A4 does not light when you press the power button

    When I press the power on button it turns green for 4/5 seconds then turns off.
    "I do all the tests the support on the page:

    * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

    * Connect the adapter to the computer.

    * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

    * Plug the power adapter into a different plug.

    * The battery, ensure that there are enough energy to start the computer.

    * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

    * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

    * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

    * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
    In vain:]

    You know? THX

    Hello

    There must be a hardware malfunction.
    You have tested a lot and nothing has worked
    I think there is not much to do, you all tired and I guess the authorized service provider could help you

    If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

  • 15 170tu ac: I HAV to press the power button several times to start the laptop...

    I HAV to press the power button several times to start the laptop... works well with the power supply on.

    all My drivers & bios is updated... but when I opened the lid... I HAV poer press several times the button and he then began 4-5 min.

    Hi @Vishalwagh123,

    Welcome to HP's Forums a great way to get help. It's a great place to find answers and advice! Thanks for the post.

    I understand you have questions turn on/off the device and you must press the power button several times for him to start. I'll be happy to help you.

    Please try these steps first. Perform a hard reset.

    • Steps to do:
    • Turn off the computer and unplug the charger. Then remove the battery.
    • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
    • Replace the battery and the charger plug it back. Try to turn on the computer.

    If it fires up immediately the issue is resolved. Otherwise, try to turn on the computer without the battery and check that it works immediately.

    In your message, you said that it works very well with the charger. However, I need more clarity here to help you better.

    It works immediately when the adapter is connected and the power button is pushed only once?

    If you again press the power button several times, it may be a faulty power button, and you will need to contact the hotline at the service of the unit.

    Let me know what happens when you try to turn on the unit without the charger?

    Visit this link to contact support phone:

    http://HP.care/2bjG4nE

    Hope the problem is solved without hassle. Please keep me in the loop.

    Take care and have a week Holy.

  • I can't turn on my wireless (wifi) on my laptop, even when I tried to press the function key and F8

    I can't turn on my wireless (wifi) on my laptop, even when I tried to press the function key and F8. I have a toshiba laptop, and there is no switch on the side of my computer what is expected? Help someone?

    Hello

    My older Toshiba has a power switch WiFi.

    My new Toshiba has a WiFi switch above the F keys, although I do not know which varies
    by model. So check with Toshiba support, their documentation online and drivers, and
    ask in their forums where there will be others with the same model.

    Toshiba - Forums
    http://laptopforums.Toshiba.com/

    Toshiba - Contacts
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

    Toshiba - drivers - access your model
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

    Toshiba - Support
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • Tecra 5200 - nothing happens after pressing the power button

    When I press the 'power' of my Tecra 5200 kids button nothing happens, only the front panel power led lights, but laptop does not start - in fact, nothing happens.

    Earlier, I lived as a result of problems;
    -the internal HARD drive didn't work, so I put the HARD drive in the Select Bay adapter and switched 2 hard drives (for each child 1 HDD with their own software / games)
    -computer had very hot on the surface (I had tried to open the computer and to clean inside, but it is still very warm)

    Now to my question.
    -If the computer does not start, is because of the HARD internal disk problem (found out once in awhile, he recognizes an old HDD, I had attached to internal port, otherwise the DVD player was not working)- and an easy repair is possible
    - or would it be possible that the CPU got too hot and bust, which means that I spend any money on the repair.

    I hope someone can help and give his opinion.

    > Toshiba guy;
    > Please publish guides on your website on how to open the 'old' notebooks, in fact no one would spend money to repair them.
    I agree with you. I don't think that someone will spend a lot of money to pay reparations for these old books.

  • Problem intermittent boot Tecra S2 after pressing the power button

    Hi all
    I have a Tecra S2 with the 6600go GFX card.
    The machine is large but presents the following problem.

    After that the machine was interrupted for a while it will start not reliable.
    You press the power button. Either as soon as you release the power button or a second later (changes every time) the green power light comes on. The fan spins at high speed then slows down to a crawl a few seconds later (as usual) but LCD does not illuminate.
    Also when it does not start USB devices are not initialized (I have a product key dongle which will flash if it is not initialized - when you start the laptop properly this dongle on continuous - a normal start, it is initialized before the ramtest BIOS)

    I've updated the bios a couple of times - it is now 2.4 (I noticed the power button timings were changed in the V1.9) but this has not solved the problem.

    I tried to start on the current with battery removed, ca battery & battery only - the result is the same.

    I can start later button power until the laptop off, wait a few seconds and then try to get back to work.
    After several of these cycles, it will begin eventually to the top. Recently, it seems that it took several attempts before start-up.

    If I have used the laptop for an hour or two and then turn it off it will start almost always a first time.

    If I put the laptop to sleep (orange slow flashing power LED) then half the time that it will continue when you press the power button - the other half of the power LED will switch to the green but the LCD display remains inactive & I switch the power button.

    Any help or advice would be welcome.

    Thanks in advance,
    Robin

    Hello

    This seems very odd.
    First of all: you can boot from USB only if the floppy drive is attached.
    You can boot from these devices USB-drive floppy/disk HARD/ODD/LAN.

    In my opinion the other unit starts the sound not as issues not a software problem.
    I think there could be something wrong with the hardware. But it is not easy to say what it could be exactly.
    You know, the look on the material is necessary.
    I recommend you contact Toshiba service partner in your country.
    They have much more experience in such cases. Guys can run tests and then can give you correct information about the failure.

  • Why Satellite Pro A300 does not start when you press the power button?

    Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

    In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
    Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

    What should I do to get a normal departure procedure?

    When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

    When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
    The same thing happen on my Satellite A300.

  • Satellite L550-1CW does not start by pressing the power button / stop

    I have a Toshiba Satellite L550-1cw that won't start, lights up when I press the power button all the lights at the front, the fan starts and he is looking for a HARD drive for about 2 seconds and then stops.

    I tried a new HARD drive, but the same happens.
    I was told that all this must be ignored and buy a new one that is not an option.
    I love this laptop and want to run again as this is the best I have ever owned.

    Help, please

    Andrew

    Can you give us more information on this vulnerability?
    You see something on the screen after pressing the power button?
    You can access the BIOS by pressing the F2 key immediately after switching on the device?

    Despite this whole issue, I think that if nothing is visible on the screen it could be a serious problem with one of the following: RAM modules, motherboard, CPU/GPU.

    From my experience the RAM memory modules are not very expensive (2nd hand might be good enough) and the replacement isn t very delicate in the case where the faulty memory causes this problem, the laptop could be set for a little money.

    But in case of problems of motherboard, laptop repair procedure could be very expensive.

  • Satellite A200 23W stop seconds after pressing the power button / stop

    Hello all :)

    I just bought a laptop Toshiba Satellite A200 23W a few hours ago.
    I turn it on and let it complete the installation of Vista.

    After the installation of Vista finishing it asket to resturn laptop and from that moment, the laptop is "dead".
    After pressing on restart the computer (from Vista) computer turns off without problem, but he never did it again!
    After a few minutes of waiting, I tried to start it by pressing the power button.

    Now when I press the power button, I can hear the HDD work and most of the time until I see something on the screen of the laptop computer stops!
    Now, I noticed that both the battery indicator AND the DC IN light are hot flushing and stop Flash at times.
    Reading the manual, I guess that the DC IN indicator should Flash in all not well.

    I tried to uninstall the battery and try to start the laptop, but in this case I can't even listen to the HDD, commissioning!
    I try to unplag and replag (on the laptop as well as Jack) power cable but again no result.

    Any ideas of what past?
    Thank you very much

    I don't know what the problem is here and, in my view, should not be so important to you. Contact your dealer as soon as possible and to talk with him. Explain the situation. You will get may be new notebook. Otherwise, please contact the nearest authorized maintainer and let check your laptop.

    The laptop is brand new and it should work. Please do not wait too long.

  • I can't start with Satellite P10 by pressing the power button more

    I can't start my Satellite P10 by pressing the power button more.
    Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

    I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

    So it must be a problem with the key.
    No idea what to do?

    Thanks for any help

    The best.

    Tobias

    If it s a button or a power supply electronic problem, then you can't do anything.
    In this case assistance by the technicians of laptop would be necessary.

    But the next time that you should try this option if the laptop turns on not;
    Remove the battery and unplug the AC adapter from the laptop for about 30 min.

    After this short period of time to reconnect the two parts and check if the laptop could start.

    Good luck

  • Lenovo Y40: Must only press the power button two times to turn on

    Hello

    A few months ago, I bought my Lenovo Y40 on the Lenovo Web site and recently, to turn on, I have to press the power button twice. When I press that once, the Lenovo logo is displayed on the screen, but after 2 seconds it turns off. On the second attempt, finally the laptop turns on and the windows is started.

    In addition, rarely the phone stucks on the lenovo logo screen, is necessary to contain the power to reset.

    Someone had some problems like these describe above?

    Thank you.
    Pedro Lopes.

    Hello

    I contacted Lenovo's Support and they recommended to perform a full recovery of the system. Apparently, it worked because I did not suffer these problems since I got windows. Probably, there was a problem with the partition that has been responsible for the initialization of the system.

    Thank you, Pedro h. Lopes.

Maybe you are looking for

  • Question about Tecra M5 stops after installation of screen saver

    Hi all Closing became a big problem for my machine since the latest updates on NVIDIA and the change of the device display utility have been applied. This happens only when the screen saver sat. I'm using NVIDIA and MicroSoft Office Manager! Aquarium

  • Docking for Satellite P100-160

    I am struggling to find how compatible with my Satellite P100-160 docking station.What they do a?Could I use any docking station?Where can I get a (or even at all)? Please excuse my ignorance, but I'm kinda a thickie when it comes to this sort of thi

  • Pavilion G4: bios passward

    forgot my password 3 times... tried BIOS apears code 55773098... What do I do?

  • HP LaserJet MFP M127fn Pro: No option to scan/administration in HP LaserJet MFP M127fn Pro

    Hello We just purchased the MFP HP LaserJet Pro M127fn, and after reviewing several videos from HP support, he showed that all of the devices in the Laserjet Pro should support the scan to network folder option. I've updated the device to the latest

  • Computer does not connect to Tv (HDMI)

    I would like to watch movies and tv on my tv through my computer shows. I used an HDMI input to connect to my tv and the sound worked for a while. But the other day I had to scoot my computer and I unplugged the cable hdmi from my computer while it w