HP laserjet 2200dn: false jam hp laserjet 2200dn

Similar Questions

• HP Laserjet 4000 t printer: Laserjet 4000 t false jam - Attention light stays on

  I have an old printer HP Laserjet 4000 t.

  I got a paper jam message , but when I searched carefully there is no paper jam.  I took out the paper trays and raised the lid of the printer, but nothing goes out the light of attention.  I even tried to unplug then reconnect the printer, but attention immediately lights up.  Now the orange attention light remains lit and nothing I assure the printer there is no paper jam, so the attention light does not turn off.   What should I do to get the printer to recognize that there are no paper jams and cut the attention light so the printer can get back to a usable state ready?  Please help me as soon as POSSIBLE.  I'm working on a deadline.  Thank you!

  THANKS davidzuts and SHThompson!

  It was a very good paper jam, but I couldn't find any paper anywhere, and using heavy paper to make out jam was not working.  I went to feedroller.com and looked up the eyes my specific printer.  I tried their troubleshooting and it mentioned ovens and assembled recording, rolls of transfer, sensors, flags, which was all Greek to me.  At the bottom of the list of items that I saw a link to the videos.  I clicked and it took me to YouTube.  There is nothing specific about a for my printer HP LaserJet 4000 t 13,20 paper jam, but there was one called 'how to fix HP printer error 13.20 to 4200 4250 4300 4350 printer HP series'.  I saw and learned how other similar HP printers came out after the ink cartridge came out.  I tried the same rough with my printer and discovered a whole sheet of paper in boots upwards in the roller behind the flipper.  When I took it off the printer immediately turned off the Attention light and returned to the ready mode!  Thank you, thank you, thank you!

• Color LaserJet CM2320nf: CLJ CM2320nf false jam

  Hello world

  I just got a used (new to me) CM2320nf CLJ. It came without the ink cartridges.

  I found a used set of cartridges HP OEM with enough life in each for me to see if I can make it work.

  When turned on, it makes initialization and then in a cleaning cycle. But I get the clear paper jam in tray 2 message. But, I can see there's no signal no matter what paper at all. I don't know what happened, but it is now asking me to load paper into Tray 1 for cleaning. This pulls at least in the book but it jams and then above, "jam-access status bar."

  I also tried "restore it to factory settings" and reset the "NVRAM", but this doesn't seem to help.

  If I remove the tray 2 paper and look inside I see picking up the wheel and it seems to need cleaning.

  

  So my questions are:

  • Should I just replace the rollers or can they be cleaned? If so, how can I clean them?
  • It seems that if I go into cleaning mode is now applying for me to put the paper in the Tray 1. He thinks that I have no paper in tray 2? How can I tell the printer to review in tray 2?
  • Are there certain parts that tend to focus on this model or questions, I need to address?

  And of course, do not hesitate to ask if I have not provided the necessary information here.

  Thanks in advance!

  Larry.

  I guess your post, as printing other pages. If so, you can update the firmware, because this report is built into the operating system of the printer. As long the other elements are print and if the printer is connected to a network, then you can get the supplies status from the web interface.

• HP Designjet 510 false jam

  I have this morning and started the fermentation.  But every piece of evidence that I try to print, I get the false paper jam.  I turn it off and on again, and it prints one.  Then when he starts the following, it does the same thing.

  Any help is greatly appreciated.

  It would be useful to mention some code the machine can be displayed when appears the indication of jam.  If it is a code of 86:01, is it possible that your rod of transport, stem stainless steel trolley slides is contaminated and must be cleaned and lubricated with a light machine oil.  The other thing that causes this code is if the thin coding Strip which also crosses the transport of the length of the drawing board may be dirty or lacks some of its retail brands, as is how transport knows where it is in the scanning process.  These two things are very widespread, as the belt that drives the transport begins to fall apart and not drive the truck correctly, but that one should be noticeable.

• New Office Jet J6480 giving false jam errors

  I just bought a J6480 Saturday.  90% of the time when I run a printing command it returns a message of paper jam.  I check and there is actually no paper jam.  I hit the OK button and it prints (with my not touching anything in the paper path).   I guess a defective sensor, but am open to all ideas of patches.

  Clay

  Hi clay,

  It is the last option. Try unplugging the power cord from both ends. Wait a minute or two. Plug the power cord directly into a wall jack. While the other end of the power cord is always unplug, hold a book and three buttons on the printer. While holding the book and the three buttons on the printer, reconnect the power cord to the back and then release the keys. Follow the on-screen instructions. I would like to know if it works.

• OfficeJet Pro 8600 false jam transport error messages

  I have two circular messages on my 8600 Pro. The first is that there is a jam in transport. "The print carriage cannot move", it is said. "Open the door ink cartridge access, varnish any jammed paper or obstructions and selec OK." But there is not any paper jam. I checked all sources of paper and they are clear. I also tried to remove one of the ink cartridges, how the cart moves happily all the way to the right and go back to the change cartridge position, with no problems at all.

  Erase this message and you get a cartridge problem... Blah, blah, blad... one or more cartridges is damaged. No they are not. Remove them and replace them all with new, same error message.

  Erase this message and you are to the cartridge jam.

  I tried the 15 second cord reset and remove the printhead (which seems very well). Any other suggestions?

  I love this printer - best thing HP produced in ten years - and I don't want to go back to work!

  It was the black cartridge. First of all, the one I tried. So the good news is, now, I have two of my favorite printer...

  Can't believe that no one else has had the same problem!

• False paper jam in nine HP LaserJet Pro 100 M175nw

  I have a brand new unit never printed a page.  As soon as I plugged it in, I got the error message of paper jam.

  "Feeder jam clear doc, reload" press [OK] to continue.  By pressing 'OK' or the Cancel of X button does nothing.

  I made (double, triple checked) there was no Ribbon, paper, packing anywhere on or in the printer.  I can even coax to print a page, but the error never stops.  It does not copy and does not print a page 100% correctly.  I cycled the printer power switch unplug the printer about 5 times and no change.  I took each cartridge and reinstalled the drum and what looked like she could be removed easily.  No change.

  Help

  OK, so I followed the instructions online for the "jam" and "false jam" at least a dozen times.  Also, I stayed and followed the suggestions of the HP cat.  A few hours later and no success what-so-ever, I finally called HP customer service for a refund.

  The gentleman I spoke to the HP Customer Service was AWESOME.  Long story short, he walked me through a few things that I already had, but at the end he told me:

  1 roll each roll that I could reach in the document feeder, just to release what it is stuck.

  2. place a document on the flat bed scanner and try to copy.

  #2 fixed my problem!  It's somehow reset the printer or caused the error to "look" somewhere other than this error.  He took a solid 2-3 minutes to "think" about the analysis, but eventually copied the document and executed perfectly.  It's been several days and the printer has played perfectly every time.

• m276nw: m276nw false paper jam

  The printer says there is a jam in the output tray.  There was a traffic jam that has been authorized.  It's a plain white paper.  Even if the jam has been cleared, he thinks that there is a jam.

  Print queue is clear, and I ran the doctor print and scan.  He sees that there is a paper jam, but I don't see where I can do something to the doctor to remove the false jam.

  I have opened all the doors on the printer and cannot find the jammed paper.

  I tried a hard reset when I unplug the printer while it is on, wait 60 seconds, then plug it in again.  He claims that there is a jam.

  Completely disassembled printer according to the instructions in the service manual and found a small piece of paper, raising one of the indicators of near the exit roller.  Apparently it must have been in the stack of paper once it has been loaded into the printer.  It's only visible and accessible after a complete tear down.

  Far as I can tell the service manuals are not available on the HP site...  You guys really should have these available on your site.  I couldn't find on external sites.

• Error of false paper jam in Deskjet 5940

  I use a Deskjet 5940 with Mac OS 10.7.4 on an iMac. It does not print, and when I check the printer queue box, it says "There is a paper jam." But there is no jam. I use this printer only for envelopes, and I checked carefully. Took apart. It will work with either plain paper. I get no response from the forum except for points applicable to the all-in-one and the same of Google searches. It's like this simple type of printers is not false jams. Checked the manual, of course, but he treats that how to fix real paper jams.

  Hello Hazelg,

  Sometimes, paper jams can be true or false. Sometimes a reset can solve recurring false paper jams. Try the following steps. I'm also including some information about the prevention of recurring paper jams, which may be useful. Good luck!

  First step: perform a power reset

   

• A9J40B: New printer: HP Envy 5530 transport Jam/Paper Jam

  I just purchased and received this printer. After the installation of the configuration and installation of the printer, he tried to print a report, but it will never work.
  He guard sends me errors and says that there is a blockage of the cart. I looked inside everywhere but this is a new printer and it seems perfectly clean. Its power to seize a white paper and then spits white. It keeps eating all the paper and sometimes give an error. I can continue or clean all that I want, nothing seems to help the problem. I tried the wizzard but he said all right and I need to print a status report, but I can't.

  I really hope I will get this problem solved, because this is a new printer.

  Greetings, tnx in advance, Jasper.

  Hey @Sjappie84,

  Welcome to the Forum from HP Support.

  I understand that you encounter some false jam errors on your HP ENVY 5530 e-all-in-one printer.  I would like to help.

  This is what looks like a brand new printer, I recommend that join you our technical support team. You can click on the following link to start a business: www.hp.com/contacthp/

  Once you complete the form online to build your business, you can choose among different means of direct contact (email, phone, chat).  This will be your best option to enjoy your printer warranty options.

  I hope this helps.  Have a great day!

• Message of paper jam paper on PC but not paper jam printer

  When I go to print, printer status box rpet 'paper jam' and it will not be printed, but there is no jam of Pope.  I have connected the printer to other computers and laptops, I have, and the printer works fine, then, of course, that there NO paper jam.  The printer says it is "ready".

  How can I get rid of this false jam on my netbook status 7 from Microsoft?  I don't know what to do.

  Restart the PC and the printer. mohanad

• HP laserjet 2200dn printer range: Hp laserjet 2200dn driver and software

  I just want to find a software and driver for laserjet 2200dn printer

  question:

  the printer does not support windows 8.1, I want to know how it works?

  My Windows 8.1 Professional 64-bit system has built-in support for the LaserJet 2200 model:

  

  You may need to click the Windows Update button in the Add Printer dialog, then wait (possibly several minutes) while additional drivers are downloaded, until the list is filled again.

• Paper jam false error HP LaserJet Pro P1102w printer

  Hi my HP LaserJet Pro P1102w printer will not print envelopes and labels. I can print documents in the usual way. I can print on the plateau of encelope, but I can't use Word 2003 to print an address.  When I check "what is the impression he's a doc of the envelope and he says Envoy."  The 'Attention' on the printer flashes.  Troubleshooting says it's a problem with the printer.  I ran the auditor of problem of HP and the message I get, is that the problrm is a paper jam. There is no paper jam!

  I would be grateful for any help

  Thank you

  Ron Barker

  Hi @RonBarker ,

  I see that you have problems printing of envelopes. I will definitely do my best to help you.

  The Word software, to change the auto power.

  When the light is flashing on the printer, if you open and close the cover, the printer should resume printing, it acts like a resume button. Given that this model does not have the button. But I've provided the steps to make the changes via the Word software.

  In Word, click on tools, select letters and direct mail/envelopes and labels, box of the envelope will be opened in the envelope tab, enter your address, click Options, click the Printing Options tab, you will need to change the autopower supply, it is probably set to manual. Check the food method to ensure that it is correctly set.

  

  If you need help, let me know.

  Have a great day!
  Thank you.

• Jams on LaserJet Pro M1530 MFP document feeder

  I have a LaserJet Pro M1530 MFP. Recently, we had developed errors pulling the paper into the automatic document feeder. It was injury but now unable to feed all documents without error of jam & constant. I followed the cleaning instructions.

  error message... "Document Feeder mispick. Reload, then press [OK] to continue.

  I guess I need to replace the ADF file. Can I do it myself or should I pay for support (currently out of warranty)

  Any help would be appreciated!

  I'm afraid that this is not something that you can fix it if it is off. If the steps outlined in the document below did not help, then the best thing to do is to contact HP support to see if they can fix it and how much it would cost.

  "The document feeder mispick" Message appears on the control panel and the ADF is not Pick Up paper or feeds on several Pages

• LaserJet P4515: LaserJet P4515 multiple paper jams

  Jam LaserJet P4515 continued in multiple locations, fuser, under the path between two tray and toner cartridge and toner area. Maintenance Kit life of 67% left, rolls have been changed, toner has changed, the vacuum cleaner, wipe with the cloth to dust and used air canned.  What else could we do?

  I searched on the OUTPUT of the fuser, PAPER END JAM and found a post indicating all food guide could be the problem.  After replacing the part (whole food guide) on Monday, there were not additional paper jams.   Thank you for your help.