HP Laserjet 2600n's frequent paper jams

Similar Questions

• LaserJet CP1525: Laserjet CP1525 generates errors 'paper jam' on almost everything I print and there are no jams

  Hello everyone, I have a Laserjet CP1525 who I am troubleshooting for a colleague, and no matter what we do whenever we try to print, we get "paper jam in tray 2" "clear jam and then press {OK}."

  I checked this printer up and down and everything autour and there is no jams, there is not a coward or a sheet of paper, the platters, and linings are very clean, I opened all the doors on the printer, but we still have this isse. Toners are all fine, black, it becomes weak, but it is quite the impression that I was able to print a single test page.  I don't know what else to do. Any help is greatly appreciated.

  Thank you!

  How old is this printer.  How it was used.  On this engine, I saw a lot where the roller is worn and it won't pick up the paper.  The roll is kind of a pain to change, but on what I laid out with this issue, once I have change the roll everything works fine.  Remove the tray paper and printing tilt up and with a flashlight he will shine on the roll.  Do not touch the roller.  There should be steps on the roll that you can see.  Most of the time there are only steps on the outside or the inside only and the rest of the roll is smooth.  If this is the case, you will need to change the roll.

• LaserJet 5200tn tray 3 paper jam

  I have a Laserjet 5200tn who gets a tray 3 paper jam, each time, prints fine from Tray 1 and 2. Page feeds on tray and stops with the leading edge just below the exit rollers. I replaced rollers pick up in tray 3 and checked for obstructions the paper path, no effect. Any help would be appreciated, I'm stuck.

  Hi DeweyE,

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do so at http://h30499.www3.hp.com/hpeb/

  Hope this helps, have a good!

• LaserJet Pro 400 (M401dn) paper jams of all trays

  Our Organization has just bought a M401dn brand new, and I've been setting up out of the box. After you have configured the IP, I went to print a report. The jams from tray 2 with the message "paper jam in cartridge area. Open door and clear jam'.» I've therefore allowed and did it again. All to nothing does not; It keeps blocking. I tried to print from Tray 1 and it's the same thing; the paper is folded in almost a concertina-style and not powered through.

  I put the correct paper (letter) in the printer sizes, updated its firmware, checked to see if there was that whatever it is hung in the transport of paper (not there), and I'm out of ideas. The weight of the paper I use is 20 lb (75 g/m2), which should not cause problems with transport.

  We bought three M401n before, and they were easy to set up. So far, I am very far from impressed by the M401dn. Any suggestions / ideas would be gratefully received.

  My first question is how recently where the unit was purchased, and you have contacted the helpline? On most hardware problems, it is best to contact phone support directly so that they can offer better, more immediate help, and they have the power to replace the unit in some cases, if necessary.

  Aside from that, you were sure to check the internal parts of the machine for anything whether on-site or any debris

  Let me know!

  -Spencer

  PS I hope you have a wonderful day!

• LaserJet 2600n: failure sensor output Possible in Laserjet 2600n after jam

  Clear a paper jam in the output area of old printer Laserjet 2600n. The paper path is clear, but the system reboots with error paper jam in the output tray.  Can't see any paper in the path, and then select button does not clear. This printer no longer exists?

  Yes, but I forgot the color of the wire August.  Remove it from the network and do a cold reboot.  This will clear internal programming.

  Then run a test page or config and see if it gives the error.   If only, it throws an error while pushing a job, the question could be anything in the page configure the DC the default controller.   This part number is RM1-1975 and they are less than $20 on eBay.

  I guess you did few checks "witch hunt", as to ensure no crack in the tray, make sure that the default paper size is correct, pulled from the fuser and fed a piece by hand, or get a dental mirror type and a little LED flashlight to check it... etc.

  With these things, there not many of us with experience on them because they were considered to be disposable.   While I personally worked on thousands of printers, I've only worked on my own 2600N, but you had no other answers in response to your question.

• Device hp 4600 paper jam there is paper jam not copied, but cannot print

  I cleared the paper jam.  I am able to copy but cannot print.  The printer says that it is ready to print?

  Hello

  You get the error message? If Yes, what is the full and exact error message?

  Method 1:

  Check the link and see if it helps:

  HP Color LaserJet series 4600 printer - paper jams

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=bpl11649

  Method 2:

  I suggest review the links and try to run the troubleshooter and check if it helps.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 3:

  Check the link and see if it helps:

  Why can I not print?

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

  Let us know if it helps.

• LaserJet P4515: LaserJet P4515 multiple paper jams

  Jam LaserJet P4515 continued in multiple locations, fuser, under the path between two tray and toner cartridge and toner area. Maintenance Kit life of 67% left, rolls have been changed, toner has changed, the vacuum cleaner, wipe with the cloth to dust and used air canned.  What else could we do?

  I searched on the OUTPUT of the fuser, PAPER END JAM and found a post indicating all food guide could be the problem.  After replacing the part (whole food guide) on Monday, there were not additional paper jams.   Thank you for your help.

• Attention kept blinking and nothing happens, not the paper jam (HP LaserJet 1022)

  Hello

  I have a HP LaserJet 1022 and when I turned it on, nothing else has happened except a flashing caution light. There was no noise and nothing happens.
  I checked a few times for any signs of paper jam, but that's clearly not is why so I took the print cartridge and it has inspected.
  The imaging drum (which is the green part of the cartridge here in this link
  http://www.Google.com.my/imgres?UM=1&hl=en&SA=N&TBO=d&BIW=1366&BiH=631&TBM=isch&tbnid=ceXkLCzurUwVaM... If I'm not mistaken had to be clean and intact. My Imaging drum has words on it in black ink which is still wet that was obviously left by previous print jobs.
  Also when it is connected to the computer without pop - ups nothing displayed on the computer screen.

  So this could be the problem of why the printer does not work?

  Any help is very appreciated!

  Here is a document that deals with the flashing light in your printer model. It will give a possible scenarios on how the lights on the printer are flashing, Advisor to the cause of the problem and then provide one solution to try to try to resolve the problem. I hope this helps.

• LaserJet 1300 paper jam

  LaserJet 3100 C3946A USBF021323 Mfg October 13, 1999

  Use of the history/primary

  A fed not location of several page for years. Only OK food for my purposes. Is not used for fax or printing from the computer. Use main scan and copy.

  Malfunction

  To replace the empty toner cartridge. First scan and copy effort leads to a paper jam in the copy with part of page rest phase in the feeder (don't remember if used not simple or multi bin for food). Page fired back with normal resistance (no tear or missing corners). First 1/3 of page was released folded in the second 1/3. Toner deposited as expected the first 1/3 and 1 inch in 1/3 second. Toner condition dry dust, unheated. Deposited toner clear and distinct than original scan. Next effort of scanning and copying. Sheet inserted in the tray sheet to the statement "Bin is empty please add paper." This resulted in "printer paper Jam check paper" Path message when paper is inserted. Can't see any piece of paper inside. Restart by pressing the "Stop/Clear".  Also turned off by unplugging the power cord for several minutes reconnect. 'Jam' same message when paper is inserted. Reinserted previous (almost empty) cartridge with results of same message "insert a paper and jam." Also tried the two reboot methods thanks to this previous cartridge.

  I would appreciate any advice that may fix this problem.

  Larry Strayhorn

  lstrayho@email. UNC.edu

  Thank you for your help.

  I guess I have nothing to lose by using the maintenance manual for the test of unity of fusion/heater.

  Larry

• LaserJet M1212nf: HP LaserJet M1212nf will not print, claims paper jam

  My LaserJet M1212nf do not print, and it has never printed. Whenever I have create a print job if printing from a PC, copy something via the scanner, or print a report in the menu, it goes through the following:

  1. Initializes the printer,
  2. During initialization, printer pulls in a piece of paper in the tray,
  3. Paper stops halfway in (seems to me like he already spent fuser, then probably would not print correctly in all cases), then the printer claims there is a paper jam.

  Note, this printer has never properly printed a single page. The number of impressions is zero (0). I've never had a paper jam.

  Note that regards the position of the paper as it is pulled into the printer, I use letter size paper, and the printer menu shows that it has set up to accept size stationery. I confirmed duplicate by checking through the web interface of the printer as well.

  Any help?

  And CV: If I can't get this problem solved, I'll have no value outside of this all-in-one at all. It will have been a large lemon and probably will poison any possibility to buy HP products in the future, including those based on the experience of support I've had so far, which has been zero. I tried to get the official support of the guarantee, but despite me documented proof of purchase, my warranty has been backdated to a until I bought itand now I can not contact technical support via the Web site options. I put in another conflict guaranteed, but on the basis of the likely response time will not get an answer until after a guaranteed year is officially over.

  Gary Dee
  wiseintro.co/deeabson

  Hey @Dee76,

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this post has instructions. Please see the HP Privacy Statement.

• On the Color LaserJet Pro CM 1410 Series HP printer paper jam

  I can't find/see the paper jam on the color HP LaserJet Pro CM 1410 Series printer.  I checked the domains listed in the manual, but there is no sign of my envelope paper jam.  Y at - it info on how to do to remove the outside cover to try to find the jam?

  The documentation provided by HP for a paper jam in the CM1410 series, I chose the CM1415fnw in this list of series as my example, can be found here.  HP does not have a document that has a complete failure of the product.

  I hope this helps.

• Tray 3 paper jam 13.20.00 for HP Color LaserJet 4700dtn

  We have a

  HP Color LaserJet 4700dtn

  which gives the message paper jam in tray 3 13.20.00

  I watch a video on a similar printer and photos on the model 4730

  but I can't seem to locate a paper sensor/banner (if it exists)

  for this particular model.

  Suggestions?

  There are three trays on this unit.

  We decided to remove the offending set and that is the problem solved

  It said users, since they have many other printers to use, that works of this unit, but with two trays.

  As it is a color model and now it works, they were happy.

  We have the tray offending in our office and we will watch more closely if something seems suspicious, but for now, the device works

• Fixing a paper jam in the printer LaserJet 1020 range.

  From time to time I see members post questions with paper jams that occur in the LaserJet printers single function. I found a video that goes through the steps of a paper jam on a printer LaserJet 1020 of compensation.

  The video will cover the following steps:

  1. Transparent area of the print cartridge paper jam.
  2. Reset the printer.
  3. Reload the paper into the device.
  4. Adjust the print settings in the printer driver
  5. Clean the surfaces of the cartridge.

  I hope the community finds it useful and informative. Good impression!

• Paper jam false error HP LaserJet Pro P1102w printer

  Hi my HP LaserJet Pro P1102w printer will not print envelopes and labels. I can print documents in the usual way. I can print on the plateau of encelope, but I can't use Word 2003 to print an address.  When I check "what is the impression he's a doc of the envelope and he says Envoy."  The 'Attention' on the printer flashes.  Troubleshooting says it's a problem with the printer.  I ran the auditor of problem of HP and the message I get, is that the problrm is a paper jam. There is no paper jam!

  I would be grateful for any help

  Thank you

  Ron Barker

  Hi @RonBarker ,

  I see that you have problems printing of envelopes. I will definitely do my best to help you.

  The Word software, to change the auto power.

  When the light is flashing on the printer, if you open and close the cover, the printer should resume printing, it acts like a resume button. Given that this model does not have the button. But I've provided the steps to make the changes via the Word software.

  In Word, click on tools, select letters and direct mail/envelopes and labels, box of the envelope will be opened in the envelope tab, enter your address, click Options, click the Printing Options tab, you will need to change the autopower supply, it is probably set to manual. Check the food method to ensure that it is correctly set.

  

  If you need help, let me know.

  Have a great day!
  Thank you.

• LaserJet Pro m477fnw multifunctional printers: clearing paper jams

  We have a rear door paper jam, but can not reach the paper - the paper is too small and too deep inside the printer.  How can we delete this?  Thank you.

  If you have access to a service manual, then you'd be able to find concrete steps to clear the jam.  We can link to the Service manuals on open forums, but you can find floating around on 3 sites of third parties.

  Otherwise, I would suggest integrating the printer a HP support certified area.  They can make the most complex repairs for you.

  You also have the possibility to communicate directly with HP support if you have the remaining warranty on the printer.  If a representative of phone you can't walk through the process on the phoen they may be able to send a tech or swap on the printer for you according to the seriousness of the problem.  Standard stuff for warranty support for the machines.