HP Laserjet M452dn: M452dn Ethernet connected but do not print
Win10 Pro x 64.
Printer connects / impressions via USB but not via a direct Ethernet connection or through router. Connection to printer Ethernet is not but installation disc is located by HP print and Scan by IP addfress doctor. Doctor says software not installed then DLs and installs the software - but still does not print. Uninstalled and did the all over again: ditto. If again, doctor without uninstalling it (still) says not installed software - although it said it was installed before I ran it again.
Router/printer Ethernet connection is good (fire port on) and the IP displayed on the printer screen, so I guess that the connection of the cable Ethernet/is OK. Network/print sharing enabled residential group. Utility of Windows/HP ID troubleshooting any problems.
Something else I could try.
Thank you
Monk
Hello @Hmonk the printer has two ways to be connected but we really recommend use one at a time if you are going to perform a network first installation you want to make sure that you have an IP address from the printer connect the network cable to the printer room will get internet brand of course, on the port on the back of the printer when you have connected cable has a green and the orange light and then go to the menu reports on the printer and print a configuration report right on the 1st page under product settings, you will find IPV4 you must subsequently make the installation at this time where everything you want to make sure, is that the IP address of its different then 0.0.0.0 or 169.254.XXX.XXX since these combinations indicates that the printer its does not properly connect to the network
Tags: HP Printers
Similar Questions
-
LaserJet 6 L shows ready but will not print from computer
My LaserJet 6 L works fine, but just today he's leaving the impression. Green ready light is lit, but sign says 'paper.' There is paper in and it will print the test page for each slot. Cannot print spreadsheet, word processing, or WordPad, PC running Windows XP. A second printer (HP Deskjet 4215) prints fine - USB connection. How to test to see if my printer cable does not?
Solved by my computer shutdown and restart.
-
C6150 connected but does not print
Printer fine until 2 weeks ago. Will not print. Uninstalled then reinstalled complete software and drivers from the HP site. Connected to the wireless access point - can see both the printer and the laptop. Said diagnosis connected page, shows wireless details. Cannot print the test page or download the exe from the HP utility to find the problem. I also have HP all in one driver. Don't know what the problem is. Product HP screen printer is connected (get the big green check mark) and shows ink levels, etc. I'm on W8 - is this a windows problem? Should I upgrade to W8.1? Or I think once again uninstall and start again.
Well that's working and really do not know why, but I think it has to do with Norton, I got a problem to update. I couldn't run same HP exe files. I was finally able to use the diagnosis exe and it worked finally.
I again that the IP address has been correct and everything was good. Somehow interrupted all Norton!
-
I tried several fixes and nothing has worked.
Uninstalling the software and printer and reinstalled from scratch. Can see and scan, but never leave print jobs queue on the laptop
HP Print ran and doctor Scan. Could not get out print job, it becomes its own test in-house printer print
I use wireless. I tried as well to turn off wireless and use the wire and still get the same results.
Hello
I think you need to delete the queue. For Windows, try it please:
Hold down the Windows key and press R.
from the run window, type services.msc and press to enter.
If the computer asks you to Admin, you have to accept that,
regarder watch down to the print spooler service, right-click and select Properties
Click the Stop button,
Go to C:\Windows\System32\Spool\printers or C:\Windows\System\Spool\printers
delete the job inside this folder
restart the machine.Kind regards.
-
Canon MX 310 connected but do not print and shows not connected
updated iMac os x el capitan (10.11.4) and now impossible to print with Canon pixma MX 310 - get the message not connected while it appears in my dock and shows point to print failed. The error log is full of messages and doesn't help me at all.
How can I get my Canon printer/scanner is working again.
Unfortunately, Canon did not write all the drivers for v10.11 compatibility El Capitan. See here.
But what you can do is to try a reset. Make sure that the printer is turned on.
Open System Preferences > Printers and Scanners and select the print tab.
Right click or control your printer on the left, then click on: reset the printing system
When she did try printing.
-
DeskJet 4645: New printer connected but do not print (without wireless or USB)
Hi, I recently bought an HP deskjet printer advanced 4645... I had an old Officejet... So, I just installed with the new printer, everything connected and implemented. It is on the wireless network and communicates properly with the Internet. It fits on my computer and watch when it is offline or online and I can view on computer ink levels, so he communicates with her (same model scanning worked...). The ePrint (by e-mail) works and AirPrinting of an iPad in the works...
BUT it won't print from the computer... Not at all... I reinstalled the program several times (app HP doctor suggested this), I swapped the printer where I bought it thinking it was a dud, I tried to connect via the USB cable... Nothing... Help, please
Hi, I installed the driver full and tried everything... I ended up buying an officejet thinking that it was the deskjet sends me problems...
BUT it still does not... I then found a place where you uninstall drivers conpletely (not in the Panel @ devices...)
It is in devices and printers (Panel)
Select a printer and then on the top of the page, click the tab saying "Server Properties".
Then select the driver you want to uninstall
Click on delete
And TADA -
LaserJet Pro P1606dn: LaserJet Pro P1606dn is on but does not print
I wrote on this forum about a week ago and ShlomiL gave me a solution that worked for a single document, but then stopped working.
ShlomiL, or someone else, can you tell me how to solve this problem?
My software is up to date.
Thank you
Susan
It seems you might have a hardware problem. Only suggestion I can give is to try a reset of the printer and if this does not resolve the issue of the cost of repairs to the printer will probably be more it is worth. Here are the instructions for resetting. Ready flashing means light the printer is receiving data and if in fact, you do not have the cable network or usb connected and it still flashes, then it's a hardware problem.
Service mode functions
Product resets
To restore the factory the product's default settings, follow these steps.
1. turn off the product.
2. switch on the product and while it is initializing press on and hold the two buttons on the control panel to the same
time until that all lights blink in unison. -
Printers HP LaserJet Pro P1606dn is on but does not print
Hi hhj121970,
What kind of error (if any) you get when you try to print? Did you run print HP and the Scan doctor yet? If this is not the case, click on the link below for more information on the download, installation and running the tool:
-
Printer shows ready and connected but does not print how to reconnect it
Printer HP Photosmart 5520 is not yet shown under devices and printers, but when I do caillet shows Photosmart 5520 connected and ready, but it will not be printed. Only, it started when I had another problem with emails and respond and called century link (my emailer) on another problem. Can someone tell me what to do, I have the disc and have inserted and nothing going on help please, I really need the printer.
Ron,
Thank you for your answer and I did something that apparently worked. Before your apply I shut down the computer and the next time I opened it, the printer worked. I think there were some documents before and when I turned it on again, it worked. Thanks for your reply, I did apparently accidentally.
-
Router reconizes printer says its loan, but do not print
Go to HP and maybe Linksys support.
-
HP Laserjet 1018: Printer light blinks 15 times but does not print
I have 2 printers, my work horse HP laser jet and a Brother Multi printer/scanner/fax etc. Both printers work correctly when connected (usb to LJ1018 connection) or wireless (Brother MFC) to my notebook running windows 7 lite.
My desktop HP compaq core 2 duo machine is connected to two printers with the help of a brother network cable and a usb cable for the LJ1018 but I decided to connect the brother wireless to my network, because it allowed me to use my netbook without having to plug in a usb or network cable. I also created my office to connect wireless to the brother and it works fine, but now I find that I can not use the LJ1018 that I think only has a usb cable connection. Although the computer says the printer is connected it is flashing the light several times - about 15 but does not print anything. I tried to reinstall the USB driver but this makes no difference. One thought I have is that Windows XP cannot deal with a wireless connection, but also a connection usb, if yes can I have go back to wired connections?
Hi @petec48,
Personally, if it is not broken, do not fix.
-
WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network
I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you
Firewalls are disabled on remote computers?
-
Cannot access Internet. It says I'm connected but will not display web pages.
Original title: web no
Unable to connect to the web says I'm connected but does not display pages
Hello
I suggest that refer you to the articles below that explain some troubleshooting steps basic to perform when you receive Internet connection problems.
Why can't I connect to the internet?
http://Windows.Microsoft.com/en-GB/Windows/cant-connect-Internet
Why can't connect me to a network?
http://Windows.Microsoft.com/en-GB/Windows/cant-connect-to-network
If the advice above do not work, try to run a startup mode in minimum mode which must start Windows with only a minimal set of services and programs.
How to do a clean boot mode
http://support.Microsoft.com/kb/929135
Note: After you perform a clean boot, be sure to check the "How to reset the computer to start normally after a boot minimum troubleshooting" section on the article above to start Windows normally.
Thank you
Legaede
-
Cisco vpn client to connect but can not access to the internal network
Hi all
I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network
Any help would be much appreciated.
Hi Samir,
I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml
(The link above includes split tunneling, but this is just an option.
Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.
Let me know if this can help,
See you soon,.
Christian V
-
Scanning HP MFP 1536, but do not print
We have a MFP 1536 which will scan & fax, but do not print. I tried to reinstall using the disc included, but not luck. I also tried to use the universal print driver for Windows XP 5 PCL and PCL 6. Still does not print. Any help is greatly appreciated.
Try to use the full functionality driver download it install the printer. It should have the latest drivers and the features of your operating system. If this does not work, I need to know who manufactured your computer.
Maybe you are looking for
-
When installing Visual C received then Error 1935' Microsoft. VC80. Open MP type = "win32policy", processor version 8.0.50727.762 Architecture = "x 86". Running Windows Vista 32-bit - I'm no guru IT but can generally follow clear instructions - can a
-
Designjet T770: Network of HP Designjet T770 custom paper size
I want to add personalized to my printer driver paper size. I know that I can change manually on each computer that I have installed the printer, but I would like to add several custom printer paper sizes, so whenever I need to install/connect the ne
-
Windows activation is not Possible
Hello I try to activate my Windows 8 Pro but I'm getting following error: DNS name does not exist (error Code: 0x8007232B) I don't have the option to activate by phone. I'm in the Dominican Republic tried the number on this list: http://www.microsoft
-
doubts in the database using backup controlfile recovery.
Hi gurus,I have a doubt in database recovery using backup controlfile.I do not speak of "ORA-01207: file is newer than the control file - old control file.Here, any of our files archive / redo log have been lost and the problem of lack of update in t
-
Time-out error waiting for VMware Tools start in the prompt
Hello people,I used PowerCLI 5.5 Release 1 connection to my 5.1.036098 vcenter (ESXi host 5.1.0 1065491 management).I'm connected (non secure warning) and be able to start the virtual machines.I try to run a task on the network of a VM VMware documen