HP laserjet pro 400 425dw scan program

Similar Questions

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• LaserJet Pro 400 M451dn: Problems copying documents from the printer scanner

  I use a Mark II of Canon Canoscan 9000F scanner to scan documents and copy them into the HP LaserJet Pro 400 451dn color laser printer.  I use the 'Copy' button on the front of the scanner function.  When a color or photo document is scanned this way the red and blue colors are reversed when it comes to the printer off.

  Both the scanner and the printer work perfectly in all other situations.

  Somehow the red and blue colors are to be swapped when a document goes to the scanner to the printer.

  I called the Support Canon technique and they told me that they have never heard of this problem and have never had it reported before.  When you use the "Copy" button function there is no setting that can be done. The scanner copy what he sees.

  So why the red and blue are exchanged on the printer?

  Teknishun

  What happens if you scan the document itself to the computer and then print the scanned copy? If it is ok, then the question must be the scanner software which sends the document to the printer and has nothing to do with the printer. Sorry, but it's a hot issue.

• LaserJet Pro M275 TopShot: Scanning question/icon

  I use Windows 8.1 (64-bit) and I have a printer HP LaserJet Pro M275 TopShot.  When I got my HP computer, I got a HP scanning icon which I could click and scan easily and also to scan multiple pages into a single document.  I recently had to get a new computer, which is a Dell, and now she just a scan icon and I can scan only 1 page... If I want the 2nd page, I have to save it in another document.  There is no option to scan another page that I used to have.  It only allows me to choose the file type, color mode, resolution and "save to...". ", nothing else.  The used scan automatically appears on the screen and I could crop for how I wanted to only it.  It does not now.   How can I get this back to the way it was?  Thank you!

  Hey @2CatsonEmerald,.

  I understand that you are having problems when your TopShot HP LaserJet Pro M275 MFP scanning to your computer Windows 8.1 that your HP scanning software is missing some crucial features that you had on your old computer. I would like to help you today with this problem of HP scanning software. Can I please you follow the steps below.

  Step 1: Remove the drivers:

  For the purposes of troubleshooting, it is essential that we have a clean slate to work with. I will, you remove all traces of your HP Laserjet in your computer Windows 8.1. If you use a wired USB between your computer Windows and Laserjet, please unplug this cable now.

  1. Open your Start screen by selecting the Windows icon at the bottom left of your computer screen, or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. On the start screen, type programs and features. Click on programs and features to run
  3. In the window programs and features will populate a list of the programs installed on your computer. Scroll through this list and find your HP Laserjet.
  4. When you see your HP Laserjet, click it and select Uninstall
  5. Please follow the prompts on the screen to complete the uninstallation. Once the uninstallation is completed successfully, please close the window programs and features and continue to the next step.

  Step 2: Remove temporary files:

  1. Open your Start screen by selecting the Windows icon at the bottom left of your computer screen, or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. On the start screen, type run. Click on Run to launch the run dialogue box.
  3. In the run box, type %temp% , and then click OK
  4. When the Temp folder opens, select Ctrl + A at the same time on your keyboard. Everything in this folder will highlight now.
  5. Select the "delete" button on your keyboard. The Temp folder contains the temporary internet files. None of the actual files or folders on your computer will be affected by deleting Temp files. A Temp file should you will automatically get the pop up to 'jump' this point.
  6. Close the Temp folder when it is empty
  7. Right-click the recycling bin on your desktop and select empty recycling bin

  Step 3: Install the device:

  1. Please click here to download the latest drivers for your HP Laserjet Printer
  2. Once the download is complete, follow the prompts on the screen to install your printer
  3. Once installation is complete, please try the scan function to check if all your scan options are returned.

  Please reply to this message with the result of your troubleshooting. I look forward to hear from you!

• M475 MFP HP LaserJet Pro 400

  I just put a laptop for windows 7 64 bit. After you have installed the software package for a M475 MFP HP LaserJet Pro 400 via USB it analyzes not the sheet feeder. The scans are empty. Any ideas as to the cause.

  Lemmy25,

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a printer. You can do so at http://h30499.www3.hp.com/hpeb/ .

  I hope this helps.

• LaserJet pro 400 m451nw - Print is too dark

  I have a LaserJet Pro 400 M451nw color, and every time I print any type of blue, it prints really dark.  Tonight, the blue on my monitor was a royal blue, and blue printed was almost black. I reduced the blue on the graph, but it's still not royal blue.  The program I use is MS Publisher 2013.

  Is it possible for me to adjust the parameters of the cyan cartridge, so it will not print so dark?

  Thank you

  SHJ

  Hello ayligcjdesign,

  Welcome to the HP Forums.

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Thank you for your time.

• LaserJet Pro 400 - M475dw, not recognizing USB drive-resolved

  I've been scanning to .pdf on a USB for about 6 months on my LaserJet Pro 400 - M475dw.  All of a sudden, it says "Insert USB Flash drive" whenever I try to scan, even if there is a pre-installed flash drive.

  I tried all 3 USB keys I've already used, more a few others.  I also tried their reformatting.  All to nothing does not.

  Today, I have updated the firmware of the printer to see if it would help - but no.

  Tried to turn it on and out, several times, including leaving them for a few days.

  Has anyone else had this? Did you solve it?

  P.S. This thread has been moved from Laserjet multifunction and all-in-one. -Hp moderator of the Forum

  handsome young man came out today of HP and replaced, the USB port and the Board at the back of the machine, we have proven that the cable was still very good.  BUT it (I was certainly not int eh room right here) was able to break a little different - so that the ordered summer and he will return to replace the fuser unit tomorrow.

  HP were super helpful and REALLY happy with the printer was still under warranty.

  Thank you for your help chaps.

• LaserJet Pro 400: Watermark not printing on Laserjet Pro 400 on Windows 8

  On the computer of Windows 8, watermark does not print on Laserjet Pro 400 connected by USB. Please note: the function watermark works on other printers not HP, as our networked Ricoh copiers. The printer prints a watermark on a Windows 7 computer. Using the driver package LJM351_M451_Series-12200-drv_installer.

  Very hard to advise without additional evidence (such as samples).

  With my Windows 8.1 Pro 64-bit system, I can print watermarks on my LaserJet Pro MFP color 400 M475dn (equivalent of MFP M451) device.

  Attached is a zip container file:

  • Small text in the abcde.txt file that contains the text "abcde".
  • Print file abcde.prn contains the print job generated by opening the text file in Notepad and by printing the document (using the driver of HP LJ300-400 color MFP M375-M475 PCL 6 (61.120.5.12262) UPD version 5.3.0.12262), by specifying the "SAMPLE" watermark with the default settings; exit 'captured' by using the option "print to a file.
  • Text file abcde.prn_analysis.txt contains an analysis of the contents of the print queue.
  • PDF file abcde_scan.pdf shows a scan of the printed output by sending the contents of the direct .prn file to the printer port.

  Try to send the contents of the .prn file direct to your printer port; for USB connect, you must use something like:

  copy  /b  abcde.prn  \\computer-name\share
  

  in a Windows command prompt session, where:

  the computer name is the name of the workstation;

  share is a share of the Windows printer instance name.

  The resultant prints show the watermark of the SAMPLE ?

  If so, then the printer handles the commands to the printer (in this case using PCL XL) OK.

  Can generate something similar to your driver for analysis?

  [You will probably need help moderating to attach files in this forum].

• HP LaserJet Pro 400 MFP M425 - paper supply is still legal

  HP LaserJet Pro 400 MFP M425

  IM unable to have paper paper feed use.

  I can scan with the scanner bed and there select the paper letter correctly, but when I try to use the paper feed its still legal size

  Ive has restored to the default factory settings, but still the problem persists.

  How can I make the change to have select letter size.

  Thank you

  Hi @biggddc and welcome to the Forums of HP.

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do to Commercial Forums of LaserJet HP.

  I hope this helps!

• LaserJet pro 400 drivers for Windows 2000

  I have a m451dn color laserjet pro 400 I have purchassed.

  One of the systems in my network is a windows 2000 system that is loaded and set up with many programming tools and so on.

  I don't want to break this fine computer running system.

  I don't want to have to reload everything in a new system.

  Simply because it is old, it seems that HP has decided to does not provide not printer drivers for it.

  I connected to the printer on the network, the IP address and tried some older printer drivers.

  The printer works fine if I don't have a color.

  It would be nice to be able to print in color.

  Is there a color driver that is compatible with this printer and Windows 2000?

  Now that I have fought through, I have a way to make it work

  Select another driver from HP - HP Color Laser Jet 4500 worked for me color

  go to the printing preferences - paper quality - check the color

  go to priferences print, cocument - advanced - options - select color

  go to color management - you may need to add a color here profile

  I don't know how this is required, but it works now

  I had to fix on the printer through the actual IP address

• Where is the location of the fonts on LaserJet Pro 400 MFP M425dn dimm?

  I recently bought a LaserJet Pro 400 MFP M425dn and to install a strip of memory custom font I bought for another printer that accepts fonts DIMM.

  The problem is that I can't find the font dimm location, even if the configuration of the printer said very clearly that there is a 'Slot DIMM 1. Said user's Guide: 'this product includes a panel of memory which will accept the following third party font and barcode... '. "- but it does not say where is this"sign of memory. "

  There is a door on the left side of the printer, but it has only a rectangular socket, not a DIMM slot.

  Can anyone solve this mystery? Thanks much for any help.

  Thanks - but it was not the question. I'm not trying to add memory to the printer, but instead to add a MEMORY programmed bar that includes additional fonts.

  For the love of someone else who may be interested, I finally found the answer to my own question on TypeHaus website:

  This side door on the left (in fact) the door to the DIMM of fonts. I didn't recognize it as a door of police-dimm because the last style font dimm HP uses different hardware than what they used in the past. The new design doesn't have the pins on one edge of the DIMMs, as do the older styles, but instead uses a rectangular connector on the underside.

  You can see the answer here:

  http://typehaus.com/pubs/custom/Fcd1/insg/Custom_Fcd1InsgHpxx120611AS.PDF

  The illustration is specifically a D401, but the design of the door and socket are identical to the design door and taken on the M425dn.

  I hope this can help someone else who may be as puzzled as I was!

• MFP HP LaserJet Pro 400 M425dn cold reset

  Hello!

  Help me! How can I make cold reset HP LaserJet Pro 400 MFP M425dn ?

  You can do 'factory reset' menu of the control panel; or permanent initialization of power first, holding and cover the corner area to the right / left of the control panel when you feed on... release your finger when you see «initialization permanent...» ». After you complete and return the loan, it indicates the reset is complete.

• LaserJet Pro 400 color m451dw: printer Laserjet Pro 400 color m451dw for window 10 drivers

  I can't find the drivers for a m451dw Color Laserjet Pro 400 running on Windows 10.  The only available operating systems are Mac.  Is there another place to look for drivers window other than the drivers regualer section 10?

  10 64-bit Windows

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5076462 & swLangOid = 8 & swEnvOid = 4192

  10 32-bit Windows

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5076462 & swLangOid = 8 & swEnvOid = 4191

  ------------------------------------------------------------------
  Say 'Thank you' by clicking the Bravo (Thumbs up) button in the post helped you.
  Please indicate the position that solved your problem as "acceptable Solution".

• laserJet Pro 400 color: printer

  Hello Mr President
  I want a help on your part I have a Color LaserJet Pro 400 m475dw MFP
  and when I turned it on. I show masseage like this {10.1002 electric memory error}
  How can I solve this problem, Mr President

  Hello Sir,

  The error that you expose is a problem with one of the toners.
  The magenta to be precise.
  
  In this case, the recommended action is to replace the magenta toner with an original RESUME.
  
  Kind regards

• Windows RT and HP LaserJet Pro 400 M401w

  I'm trying to connect the HP LaserJet Pro 400 M401w to my Surface tablet running Windows RT.

  I tried to put in the IP, wireless sensor and using the USB cable.

  He is not with the IP or wireless detection.

  With the help of the key USB Cable it things is a CD Rom   If I add a printer and trying to choose manually the printer isn't on the list.  Any help would be appreciated.

  Hi SydsMom, welcome to the Forums of HP. If a product contains the necessary built in the RT drivers, he just needs to be plugged and RT Windows should recognize and install it.
  
  I did a search for "HP LaserJet Pro 400 M401dw Laser printer" with the: Windows Compatibility Centerand it's Windows RT 8.1 compatible.
  
  Microsoft provides these simple instructions: install a printer in Windows 8.1, Windows RT 8.1
  
  In addition, I'm not familiar with that printer, as it is a business model supported. I suggest posting in the trade forums, to get more input. You can do this HERE.
  
  Series HP LaserJet Pro 400 printer M401 Support