HP officejet 6210 all in one fax
HP officejet 6210 all-in-one, fax not send fax with Vonage phone, I'm sure that most people have no problem, what should I do to fix this? Help, please
I'm sorry that you are experiencing this issue. The fax works with Vonage, BUT it doesn't really work that well. This may sometimes work, it may not.
Vonage is a (VOIP) Voice Over Internet Protocol. It has many transmitters communicate in both directions and can cause the interruption between the lines. You can try some steps, but it may not always work.
1. go in the settings of your Fax
2. change your Error Correction Mode (ECM) - OFF
3 set the fax speed to slow DOWN
Make sure it is properly connected.
1 LINE 1 at the rear of the printer goes directly to LINE 1 of the Vonage modem (or wall plug)
2 LINE 2 goes directly to the phone.
Hope this helps. Let me know what happens.
Tags: HP Printers
Similar Questions
-
- This printer is about 4 years old. It has a usb port to plug into a computer. My question is, can I buy a WiFi b/g/n dongle to make my printer wireless if it wasn't initially a wireless printer? Its a HP Officejet 6210 all in one. Thank you
Yes, but it is difficult to get a takes in charge of work and only impression, not sweeping.
-
HP officejet J4540 all-in - ONE: fax
When you try to fax with my hp officejet J4540 all-in - ONE I hear the tone, the display shows fax is connected, but I get always a message "fax send failed". I ran a fax set up the test and everything passed. The question might be the telephone line in my house? Phone company put a new filter on the fax line and he sent a fax that day, but none after that. He always says "fax sending failed.
Hello
Please contact us. I understand that you are unable to send faxes from your printer.
You can follow the steps mentioned in the document.
Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.* *.
-
I had printer for 6-7 years and never had a problem. I up graded my phone att pots line (plain old telephone system) the system to voip (voice over internet phone). I never had a problem to send and receive faxes. Now, I can only send faxes and not receive them, even with the automatic reply button on! The only rings (6210 HP) fax. Chat with people to send faxes reports the 6210 indicates the machine is busy, which is not the case. I checked the telephone connections and cables and still get the same results. I have checked the filters and hooked up to another fax machine (hp 8500 A909a) with the same results. I downloaded a updateded printer driver and still get the same results. I noticed when I sent a fax test fax hp service test, they sent a fax to the back but the fax would only ring unless I press the black / touch of color, it will leave a fax come through. Y at - it a remedy to this new problem. Help.
Hi @MACMAN55 and welcome to the Forums of HP.
I understand that you are having problems of fax. I would like to help.
Switch to a VoIP system may cause problems. The fax machine is designed to operate with an analog installation.
I'm including a couple of documents with more information, as well as instructions on how to get the best performance from a line VoIP:
Faxing on a voice over Internet Protocol (VoIP) Service
Please let me know if you have any questions. Thanks for posting on the HP Forums.
-
HP Officejet 6210 All in One not working with Snow Leopard
Downloaded SL yesterday and all of a sudden I cannot print. It is considered to be one of the compatible printers. I did a print test and it worked, but none of my apps (Word, Safari, etc.) will be printed. I have checked my selection of the pilot, system information, deleted the driver, reinstalled the driver (from the MAC disk supplied with the printer), unhooked and rehooked everything, restarted my computer, etc. Can't seem to connect my printer to my applications, even though the MAC in the preferences system, etc., seems to recognize it. Any ideas? Thank you
Tried all of this. Didn't work unfortunately but thank you for trying to help. Finish reloading Snow Leopard all over again and that seems to help to deal with many problems. Don't know why reload solved a lot of problems but at least I can print in Word which was what I really need at the moment to get a project.
Thanks again!
S4Girl
-
I just connected the hp officejet 6210 all-in-one printer and it won't let me scan.
Message on printer: "You must run or install software device" I just installed in my computer and cannot parse. I don't have the software because the printer has been givin to me.
Hello
You need to install the complete software to activate "scan to computer".
You can get the drivers here
-
HP Officejet 6210 All In One prints only on the left side of the page
After good results, I tried to print a "retail Transaction" of Quickbooks account form twice with the same result:
info. prints only on the extreme left, a straight line down... I did adjust the paper tray. What could be wrong?
Thank you for your time and your advice.
Texas-sleeper
Salvation to the texas-sleeper,.
I understand when you print from Quickbooks print right on the left side.
I'll be happy to help you.
In the program you are trying to print from, click file and then click on print. The print dialog box opens.
Select your printer, click printer properties or properties.
Click the paper/quality tab.
In the press or type click on the dropdown menu, select the type of paper that matches the paper loaded in the paper feeder and the desired print quality, paper size, select the correct size of paper.Make sure that the appropriate paper size is also selected in Quickbooks software.
Try printing a different file where this file is corrupted or damaged.
I have provided a document of Quickbooks print does not correctly.
Solve common printing problems.
Try printing from another application to see if there a software problem with the printer or application you are printing from.
I hope this helps.
Thanks for posting on the HP Forums.
Good day! -
Office HP jet 6210 all in one error r
my hp officejet 6210 all in one giving me the following message appears on the screen of my computer when I try to scan a document. "reinstall the software photo & imaging and try again" when I use the installation disc keys that it not allow me to complete the installation even with me being the administrator of the pc!
I'm going to post you a link to a post from Shane_R that describes the uninstallation steps that I think could help clear on issues that may keep to complete the installation.
Version 14 software and full scrub for no HP computers only below steps
Here is a link for the drivers for your printer. Click here
Before starting the installation, right-click on the program and select "Run as Administrator", even if already logged in as an administrator.
Let me know what happens.
Good luck!
-
Hello
I need advice to fix this... My printer (HP Officejet 6210 all-in-One Printer) that I bought in Europe does not accept the cartridges sold US. The printer identifies the cartridge 94 as incompatible. On the site of HP 94 cartridge is listed as being compatible with this printer (the original cartridge is 338). It seems that I need a new printer? It still works perfectly. Should I try other types of cartridges?
Thank you.
You will need to Contact HP to ask a "regionalization Reset." Do not charge for this, it is covered under the warranty of the cartridge. You will need to have access to your computer and printer then on line with HP. You will also need to have a set of cartridges for the new region, once completed reset cartridges of region of origin no longer works.
-
HP 5740 Officejet all-in-one: fax will transmit well if the ink level is low
Can fax you on HP Officejet 5740 all-in-one when ink levels are low with a good result?
Hello
Ink level low don't effect function fax, BUT if a level of ink is exhausted/empty you cannot use the fax because the printer stops during warm-up.
Kind regards.
-
Impossible to scan, fax, or copy of HP Officejet 6500 All-- E709a One in
I can print from my HP Officejet 6500 All - in - One-E709a, but I can't scan, copy or fax. All drivers and updates are underway; No recent updates have been made before the problems that occur. I use Windows 7 64-bit. When the printer is turned on, it still shows Original charge, but no documents are in the charger or on the glass (I already cleaned the glass and have ensured that the lid is tightly). I have problems to scan, copy and fax. The automatic document feeder works. I tried to reset the printer several times.
When I try to scan a document into the document feeder (it feeds through) or from the glass, I get varying answers - rarely, he asked well how I save/handle the doc (e.g., save them in pdf format), but the document does not actually scan and I'm headed to reload the document OR it displays no. Scanning Options. The document does not appear in my analysis.
When I try to copy, it shows the document as copy, but there is a long delay before the progress bar occurs. When I copy using the document feeder, I actually get a copy (rarely and always disappeared - looking) or copy prints white - two results are always followed by an error message to reload the document. When you copy from the glass, the copy print in white with an error message to reload the document
The same problems occur when you try to Fax. If trying to scan, copy or fax, the printer does a lot of gears whirring noises.
Again, I can print a document from my PC without any problem, the problem is limited to scanning, faxing and copying.
I tried the doctor of printing & scanning HP. It always stops at the HP Twain scanning stage, saying that the scanning process was cancelled by the user (not true). When I click on continue, it proceeds to the stage of Test analysis, but nothing happens when I click the button of Scan Test. It only will allow me to ignore at this point. All the other steps show green checks.
My first question is really going to reach the merits of the case, I heard you say that the printer produces noise, but if you lift the bar A) trip through the screen and the light cover B) up?
In addition, perform both of these resets and I would like to know how they are!
All-in-one HP printer reset - HP Officejet 6500 - YouTube'
Have a great day!
-
Officejet 6310 all-in-One: can't send faxes from the computer screen
We use an Officejet 6310 all-in-one printer. Computer of my wife, a laptop Toshiba Satellite Windows 7 Professional, has suddenly come to the point that it will no longer send faxes from the computer screen. We get an error message that something must be installed or reinstalled. We have lost the CD of the software provided with the printer. We can send a fax if we have a document printed to power the machine, and we can print faxes. We lose a lot of paper and ink because of this problem. Help, please.
Hi GregsterMc,
Given that the Fax icon is not displayed in the window of printers and devices, you need to uninstall and reinstall the software again. This should solve the problem.
Thank you.
-
Fax/scan without a phone with officejet 7410 all-in-one line
I have an officejet 7410 all-in-one and UNPLUGGED my phone line at home. How to download software in order to fax/scan items? I get the message error is "you must install or run HP software for this feature.
Here is a link that will help you with that.
http://WWW8.HP.com/us/en/support-drivers.html
1. Enter the name of your printer DRIVERS AND SOFTWARE
2. choose your operating system
3. then, when he asked to SELECT A DOWNLOAD, choose the software FULL of FEATURES.
Let me know if this can help, thank you.
-
I have a HP officejet J6480 all-in-one printer. The screen is white and yellow light flashing
I have a HP officejet J6480 all-in-one printer. The screen is blank and there is this little yellow light flashes on the Cancel button. I can not print or fax anything because the screen is empty. Since the light started to Flash the entire printer has not worked. Can someone please HELP! : womansad:
Well, if you haven't tried this and then create a coercive power reset:
Do not activate the wide (although you can), remove the power cord at the back of the printer. Wait at least 30 seconds, then reconnect the power cord to the printer. Turn on the printer. If that clears up the flashing light/white screen, then try printing etc...
If this is not the case, see if something visible is originally the error state such as paper jam, odd items in the printer, nothing fancy. Also try to plug the printer directly into the wall outlet as opposed to a look/power surge Strip, or even try a Jack in another room if it is not successful.
-
OfficeJet 7210: HP Officejet 7210 all-in-one works in Windows 10
Anyone have any suggestions for my situation?
I have a HP Officejet 7210 all-in-one I've had for a while. (It works fine all this time).
My last computer was (that is, starting to act a little "ginchey"), it was time for an upgrade... So I went to one 64-bit Dell to another.
The 7210 worked well on my last Dell, but I can't not all software (scanning, printing, fax, etc.) to properly install from CD (obviously older version of the operating system). HP website for updates of pilot is kind of useless (they appear to have abandoned this machine, no longer support).
Here's the rub: old pc was running Windows 10, new machine runs Windows 10.
Any suggestions people out there?
Frankly, if I'm just a victim of HP 'ripping off' supported by an operational device otherwise, I think go "elsewhere" for my next printer if I have to upgrade.
Kind of sad, I used to be a big fan of HP over many years, but their current support, products, etc. are leading me to look elsewhere these days.
Thank you for everything, for support, ideas, suggestions, etc.
MC in Albuquerque
Hi @mc-albuquerque.
Download and install the following software to complete functionality to use Officejet 7210:
http://ftp.HP.com/pub/softlib/software13/COL30951/MP-110165-3/AIO_CDB_Net_Full_Win_WW_140_408-5.exe
Please let me know if you run into difficulties.
Shlomi
Maybe you are looking for
-
When I try to log in, I get a series of downloads with suffixes aspx and part.I try to open the file aspx with firefox, get a white screen with a login and a text not graphics - I get my login, but it does not work - the connection box goes back to "
-
Downgrade from Windows Vista to XP on Satellite A200-22I
Hello Maybe this topic has arised more than once, but someone can help me?I just bought a Toshiba Satellite A200 [22I with windows Vista, but I want to downgrade to XP.] How can I do? Thank you very much
-
Office jet pro 8620: should I disable the printer without cartridge installed?
I removed the original HP ink that was defective and took it back. Now I have the inkjet (Office jet pro 8620) without cartridges installed. The printer says not to disable so that it does not get damaged but I'll be away for a week and want to turn
-
Offered several times KB2446708 (appear to install successfully each time)
Update of security for Microsoft .NET Framework 4 on Windows XP, Windows Server 2003, Windows Vista, Windows 7, Windows Server 2008 x 86 (KB2446708) This update is now downloaded 9 times, whenever I install it successfully an other downloads, it's mo
-
can't see the pasted images.
I am fairly new to photoshop and I followed this tutorial on how to make a banner. I had a background and I was told to copy a jpeg file and paste it and it creates a new layer. Well, he has created the layer, but now I can't see the image. what I se