HP Officejet Pro 8600 black printing/copying has vertical lines on the page. The color is fine.

Similar Questions

• How can I set up my new Officejet Pro 8600 more printing on paper photo 4 x 6?

  How can I set up my new Officejet Pro 8600 more printing on paper photo 4 x 6?  I'm running on Windows 7 64 bit.

  It's strange.  Looks like you have a second paper tray and put it to the default tray.  The second paper tray only supports the types of paper that show on your list.  It's strange because unless you have purchased a second tray paper, plus model has one.  Does only the high-end model.  Other than that, only certain types of media can be duplex, so if you have double-sided printing, it can limit the selection.  I'll watch what else could be the cause and get back to you.

• HP Officejet Pro 8600 won't copy

  My new HP Officejet Pro 8600 will not copy.  When I hit print I get an error "scanner failure".

  I called the HP support by phone as suggested, and they had me unplug the printer, then hold the power button in during 15 seconds, everything disconnected in order to "drain the power."  Once I have it plugged it back in and he began to copy correctly turned on!  Hope this helps someone else with the same question.

• HP OfficeJet Pro 8600 Plus: how and where can I find the year of the printer? HP OfficeJet Pro 8600 more

  How can I get the printer HP OfficeJet Pro 8600 year more?

  I looked in the staus report printer and the different labels I can find on the printer itself. I don't know that I just lack.

  I bought it new, so I have no reason to suspect that the information has been removed before purchase.

  Thank you

  The printer status report has 47 online date (rounded to the week) the print head has been installed.  Except in rare cases where that the printhead has been replaced, this would be the date of the printer has been installed.

• HP Officejet Pro 8600 Plus: HP Officejet Pro 8600 Plus printer-

  HP Officejet Pro 8600 Plus printer-

  Tried to copy both sides of a vehicle using ADF permit; paper too small (stupid user!); he copied the first side successfully. Now, I can't find the input document! How can I remove paper (which I can't find) which was too small for the auto feed?  It is not in the duplex unit, either.

  Hi @Dick_27,

  Welcome to the HP Forums!

  I appreciate that you try to remove the paper in your printer more HP Officejet 8600. I'm sorry to hear that, but happy to help!

  Please have a look through this guide, A display of the "Paper jam" error on the HP Officejet Pro 8600 e-all-in-one printer series.

  As well as this guide. The ADF (ADF) documents didn't pick up paper.

  I hope that these guides are useful and have a nice day!

• HP officejet pro 8600 - cannot print from my macbook pro

  We just bought a new HP officejet pro 8600 but for some reason, we cannot get my macbook pro to print on it. My mac says it is connected to it. It is listed in the printer only and all the settings look fine, but when I send a document to the printer, it will not be printed. He did print the first day we had (a week ago) but it stopped and we cannot figure out what to do. My daughter's PC will be printed, as well as the pc of my husband. It is the first time that I had problems printing to a hp from my mac. Any thoughts?

  I had my Officejet Pro 8600 about six months.  Recently, I had the same problem.  It continues to print from my Windows computers but not the Mac.   Labour goes into the impression that it is place on a wedge.  I tried many fixes, including the removal of the printer and reinstall.  Usually removing and reinstalling it will fix for a while, but now, even that does not work.  In my view, that the permanent solution is to buy another printer.

• My HP Officejet Pro 8600 cannot print from my MacBook Air

  Hello

  My HP Officejet Pro 8600 cannot print from my MacBook Air. It keeps on showing "the printer is not connected", but the display on the printer connected. I often reset the printer "EVERY TIME" I want to use. I also tried to turn off my laptop and printer several times before printing. If I'm lucky, it will work maybe for one or two prints. If no luck then I have to reset everything again. Sometimes I reset the printer, the printer is not displayed on my selection.

  Hello boojoo1tw,

  Welcome to the HP Forums!

  I understand that you are unable to print most of the time with your Officejet 8600. How is the printer connected? USB or wireless? What is your operating system on your Mac computer? Click here to find out.

  If your wireless printer, then I recommend the award of an 'IP address' by following this HP document on printer does not maintain the wireless connection.

  Please post your results, I'll be looking forward to hear from you.

• HP OfficeJet Pro 8600, HP printer wizard installs not when the software is installed from the CD

  HP Officejet Pro 8600 e printer all in one

  Windows 7

  I had Assistant printer installed and working on my computer at least a year, then there was an update and it no longer works.

  I uninstalled the device and the software and reinstalled both on-site and directly from the CD without success.

  The only error I get is when I start everything first install it and there is a red "x" next to the update of windows.

  The installation process ends, the computer will recognize the printer and I am able to print but I have no control any function because none of these options in the wizard for the printer are turned on.  They are all grayed out.   The most important thing I need is the archiving of received faxes.

  Someone else in my family had the same problem, but was able to reinstall from the Web site and doesn't have any more problems.

  Thanks for any help.

  Hi liluno18,

  I want to help you with this question. I send you this link to the Microsoft forum on how to fix the red X on windows update. Follow the response from Joseph M.

  So I suggest you do a complete uninstall software of the JO 8600 and reinstalling the software once you have windows update works again.

  Let me know if you need help, I would be happy to help you.

• OfficeJet Pro 8600 Premium - paper tray automatic selection according to the size of the paper

  OfficeJet Pro 8600 Premium, Windows 7

  How to setup the printer such as when I'm sending a legal document that automatically selects the tray 2 (legal paper in tray 2). Tray 1 is the default, with letter-size paper tray. In 'device settings' Tray 1 is set to letter and tray 2 has the legal value.

  Thank you!

  Greg

  Hi Greg,.

  At present, the 8600 does not support this feature of Microsoft. Unfortunately, there is no work around. You must manually select tray 2:

  1 Ctrl + p to open the print dialog window.

  2 Select the printer of desire and click the preference.

  3. go tab paper/quality, then select "Tray 2" on the decline of the Source of the paper in the menu dropdown.

  See you soon,.

  Kimu

• OfficeJet Pro 8600 n911g stops and you need to restart the spooler on Win Xp

  Hello

  I have an OfficeJet Pro 8600 N911g printer.  It is networked and I put the static IP address on the printer.

  I have a user with about once a day to restart the Windows print spooler service so that tasks start printing.  I loaded, uninstalled and reloaded the Windows XP drivers.

  Any thoughts on how to solve this problem?

  Hello

  Have you used the latest version of the software on the HP site?

  If not, uninstall the printer from programs > HP > printer folder and then install the latest version below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-108858-3&cc=us&DLC=en&LC=en&OS=228&product=4323648&sw_lang=

  I suspect also any security program which may block the network connection (assuming that by the description of problem on a single user), temporary disable any software firewall running and check if that can cause printing to stay in spool it print.

  Try to run the HP print and Scan doctor, click on network > firewall help and make sure any firewall running is disabled, then follow Fiox print and check what is happening:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-109037-2&cc=us&DLC=en&LC=en&OS=228&product=4323648&sw_lang=

  If still the same I guess rather the envoirnment of the OS, you can try running Microsoft Fixit to diagnose service print spooler for questions and automatically check if this can help:

  http://support.Microsoft.com/mats/printing_problems/

  Shlomi

• OfficeJet pro 8600 black vertical lines of print when copying

  I got a new of OfficeJet Pro 8600 a couple of weeks, and it worked fine until today, when I tried to copy something. I can always print from my pc and scan without problem, but when I try to copy a document (if I load it into the tray or put it on the scanner) the page comes out covered with black vertical lines of different sizes. It seems that this isn't the ink or the scanner since I can print from my pc and analysis very well.

  Help, please!

  This unit is plugged into a wall outlet directly? If this isn't the case, then try to connect the unit to a wall outlet directly.

  The 8600 Officejet Pro has built in the surge protector and double this feature may cause some problems.

  Also, try to reset the printer hard:
  * Unplug the unit while the printer is on
  Disconnect the other end of the power cable from the wall socket direct
  * Wait 30 seconds
  * Plug the unit to the top

  Let me know if it helps.

• OfficeJet Pro 8600 Premium: When copying from the plateau the copier will print only 1/8 of page, then stop.

  Copier is towards the top sometimes & don't print that page of bucket 1/8, Athens he spits as if this one ends. Have unplugged the power cord & reconnected. Ran scans printhead & alignment. Off all night. All the ink levels are good. Still has not corrected it.

  Print an entire page of the screen of the computer without problem. Printing problem just go flat.

  Hi @Wendy-needshelp,.

  Thanks for joining the Forums of HP Support for a solution to your problem copying.

  I understand that you use a HP Officejet Pro 8600 Premium e-all-in-one with a computer and Windows 7 when you copy from sometimes flat it will only copy and print 1/8 of the page. I would like to help.

  You mentioned having unplugged and replugged the power cord. This is something that could be done. If you can, I reset the power and try to connect the printer directly to a wall outlet, if you currently use a protector or electrical surge extention. Sometimes the surge protectors can limit the amout of the power supplied to the printer.

  

  There was an update firmware released in April, which can help your printer. You can download the update of the firmware and run it from your computer to install it on the printer. You can go to the HP Officejet Pro 8600 N911g_n Firmware download page by clicking here.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• HP Officejet Pro 8600 - black lines when copying, colored scanning lines

  Hello

  I have a HP Officejet Pro 8600. When I try to copy from glass, copy of ADF, I get black lines going the length of the pages. Whenver I scan, once more, the glass or ADF I get lines colored, ranging from the length of the analysis. I called HP customer service and the representative told me clean the glass and part inside of the ADF, but the problem still remains. No idea if this is a common problem? More important still, how fix it.

  Do a hard rest on the printer. Let the printer and unplug the power cord. In doing so, it will remove the lines.

  When a solution is found, please indicate the position that solves your problem.

  If I have solved your problem, please do not hesitate to provide laurels and make sure that you mark this thread as provided solution!
  Although I work for HP, my messages and responses are my own opinion and not of HP

  Valerie, printer Agent

• OfficeJet Pro 8600. Printing a list of todo in black and white

  I have the OfficeJet Pro 8600 more and I use an iMac, OS 10.92.

  I want to print a list of Todo comics in black and white rather than in color. (This is a todo list [i.e. Gaston ToDo] available in the applications in the HPePrintCenter).

  I don't see a setting that allows me to set a preference to black and white.

  Suggestions, please.

  Thank you.

  Lynn

  Hello lovemutts,

  Thank you for being a member of the HP support forums.  I see you want to learn more about the print settings with one of printing applications to which you are subscribed.

  I've included the document Getting Started with Print Apps and at the request of delivery print Apps .  In the section titled "Managed print Apps" is a sub-section titled 'print settings.  In there, it says "On some printers connected to the web, a settings option is available on the screen of the print Apps Print Preview mode that provides options to select the type of paper and print quality."  If the application you are using does not offer this option so that you will not be able to change all the predefined print settings.

• HP Officejet Pro 8600 more print but not scan

  I have an Officejet Pro 8600 and I use Windows 7 Ultimate (64 bit) and it print and copy but will not scan. I had a hell of a time trying to get this thing to scan - I even spent an hour and a half with HP technical support and they could not fix it and finally gave up and call me Micro$ oft said that it must be a windows problem (Windows is up to date, incidentally).

  I tried to open the scanner software and nothing happens when I click the icon - the loading icon flashes for a second, then only the mouse pointer. Nothing happens if I try to boot from all programs. Nothing happens if I try to scan to the computer of the other printer told me the failure of sweeping and that there could be reasons of severalpossible (unrelated, software used, etc.).

  I have installed and uninstalled. A couple of times he was having trouble with the installation, but finally got it connected. Once it would not uninstall in Control Panel until I did it directly from the HP folder. I connected it by USB and wireless. I installed the version of bloatware. I cleaned that out and I tried the only version of drivers. The HP support person had me go and removed a bunch of stuff in the registry. I tried to run as an administrator. Nothing works. I even tried to scan using Windows Fax and scan. I disabled Kaspersky and made sure that my firewall is turned off.

  I am at my wits end with this and certainly regret my purchase at the moment. Help!

  Hello, it happens to the analysis of Windows (WIA) and generates an error:

  "The Windows Imaging service does not work... If the problem persists, you will not be able to scan using the applications that use this service, such as Microsoft Paint. Scanning software HP could still work. »

  It asked me to restart, and then re-run the diagnostic tests, but I got the same result.

  Then, I jumped to HP Scanner Twain and got another error:

  "The Twain component is not working properly because the product is used by another process. Save your work and close all applications. Turn the product off, turn it on again, and then click on restart and repeat the test. »

  He told me then the problem persists to uninstall the software, then reinstall the Full Feature software (I did, but available).

  * EDIT

  Problem solved!  After you had me run the diagnostic tool I googled the WIA problem and found that many other people had the same problem. A person has a response from Micro$ oft saying that it was a Windows 7 issue and how to fix it - this is the text I found:

  To start the WIA service, you need start all services of dependence. To start the dependency services, please follow the steps mentioned below:

  -> > click on start-> type "services.msc" and press ENTER, once you get up the services window, please do the rest steps.

  -> > first check and write down all the dependency services: -

  -> > right WIA-> properties-> tab dependence, check the services of name listed there.

  It must contain the following services:

  * RPC remote Procedure Call

  -> > DCOM Server process Launcher

  -> > RPC end point mapper

  * Detection material core

  Make sure that all of the above services are started in the services list.

  Last time, we started the Detection hardware Kernel, which solves our problem.

  (Andy, it's important.  Choose "Detection hardware Kernel ' and start this service which should start your 'Windows Imaging Acquisition '.  If it does not then select WIA and change the departure to "automatic".  This fixed my problems) after all dependency services start, please try to start, WIA service to solve the problem of .                                                                                                                                                                                       

  (For those who are doubtful with computers, like me, when you click on the start icon, you can type services.msc in the box of research programs or click on run and type it in there). Once inside the list of services, you can look at the dependencies by right-clicking on the Windows Image acquisition service and selecting Properties. Take note of these dependencies. Then back to the main list and watch to see if these dependencies are started. My Shell Hardware Detection says disabled, so I right click on it; However, starting selection is grayed out and I couldn't select it from the drop-down list box, so Startup type I selected Automatic, apply, close the Services window and then started my Scan software and presto, it worked.

  Thanks for setting me on the right track!