HP Pavilion a1340n no VGA no signal after memory upgrade

Similar Questions

• Pavilion DV6-2010sf: HP Pavilion DV6 Sound no longer works after Windows upgrade Windows 7 10

  After upgrade to Windows 7, no noise, even with icons on the screen at the bottom left and keyboard sound ON display.

  ATI driver high definition Audio Device was running OK.

  Audio CODEC IDT High definition driver was NOT working and unable to do so.

  I ran Windows Update but who has installed a new version of the drivers and Audio CODEC IDT High definition driver now works OK, still no sound even with icons indicating it is under tension.

  The HPSupportSolutionsFramework of the HP utility that is supposed to help can be downloaded: 10 seconds after download starts, it will stop ith error notification (and no explanation).

  Any help welcome.

  Hi @JFR77,
  
  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!
  
  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dv6 Notebook and no sound after a updated Windows 10. I uninstall that I listed in the audio, video and game controllers first and reboot the laptop. Then download the driver Audio IDT high definition (HD).

  You can try:

  1. a click right icon "speaker" (right)
  2. Select playback device
  3. click right speakers
  4 activate and as default
  5. click apply/OK

  Here is a link to troubleshoot the sound.

  Please let me know how it goes.
  
  Thank you.

• Satellite P100-219: overheating after memory upgrade

  Hello guys,.

  I've recently upgraded to 4 GB RAM in my laptop, and he did it again.
  Computer laptop stops immediately after awhile. CPU or GPU gets really hot. Works fan CPU, GPU was not used intensely. Simple web browsing/cat/emailing.

  What becomes hot however is part to the left of the memory/wlan compartment. Is it possible that a chipset gets hot after just upgrade memory?
  I tested the memory with Memtest + for more than 3 hours. No errors.

  Moreover, the last time that my phone was in ASP it had returned with DMI saying it's Satellite L20! I dunno if that could be related...

  Thanks in advance for your suggestions,
  mentorek

  You have blown the dust anyway? As you say, maybe another component is overheating rather than the CPU or GPU. The CPU/GPU heatsink can be shared with other chips.

  Have you installed RAM high performance? His best choose RAM that has the same Timings CASE/RAS as the original factory of RAM.

  The name DMI does not cause something like this.

  PS. If you're running Vista, you must pass the BIOS and driver nVidia on the Toshiba site

• cannot start win8 after memory upgrade

  Hi I have a HP Pavilion P6813w

  It came with win 7 64 bit installed with 6 GB of ram
  I created a duel with victory 8 boot
  It was working fine until I got my 16 GB of ram today
  Well I got the 16 GB in and turn on the computer to get to this
  Recovery
  your pc needs to be repaired
  the application or the operating system could not
  be loaded because a required file is missing or
  contains errors.
  file:\Windows\system32\winload.exe
  error code 0 xC0000001
  but when I'm out of 8 GB it starts and displays the 8 gb of ram.
  I tried to do the repair installation dvd options since the win8 and even tried it recover usb option
  When I use the usb option I get error 22 grub 1.5
  so my question is why win8 will not load with additional memory
  and even win 7 does not load
  It gives me the same error
  my computer shows he takes supporting up to 16 GB
  4 GB ram sticks
  IM experience pc users and cela just stem me
  any idea what could be the problem

  Hi Wallace,

  There is a limit of memory for Windows 8. For version 512 GB for 64 - bit and 32-bit maximum 4 GB is allowed.

  For more information, see the links.

  Limits of memory for Windows versions 

  The memory upgrade (RAM): HP Pavilion p6813w Desktop PC support

  If you have any questions on Windows, feel free to let us know. We are happy to be of assistance.

• HP Pavilion 15 laptop: amd driver update after that upgrade from win 10 leads to the boot failure.

  I have a HP Pavilion 15 laptop.

  After I my windows 8.1 upgarded to win 10 and decided to update my graphics driver amd, after the installation of update to the course to restart commissioning hangs at the hp logo (sometimes to start startup repair, then fails).

  This only happens on this specific driver update... do not update this driver translates by "display driver stopped working / crashed and now has recovered" message.

  is this a problem with the update of the driver or I can't use this update in win 10?

  Hey @AnjaneyaAnand,

  Welcome to the Forums of HP Support! This is a great place to find solutions and help our community!

  For starters I would say that the HP Support Assistant running.

  Here are some useful links for the HP Support Troubleshooting Wizard or by downloading the latest version:

  HP Support Assistant

  HP computers - using HP Support Assistant (Windows 10, 8, 7)
  With the help of HP Support Assistant (Windows 7, Windows Vista)
  HP PC - troubleshooting HP Support Assistant (Windows, 10, 8)
  HP PC - troubleshooting HP Support Assistant (Windows 7)

  I highly recommend to run the Windows Update tool that it can find and update all the old drivers or missing you need.

  Please hold me.

  By pressing the Thumbs Up button below, you can always say thank you!

  See you soon,.

  TechSurge.

• HP Pavilion dv7 Notebook PC: Wireless Off after 10 upgrade Windows

  I adjusted has upgraded to Windows 10 (x 64). Since doing the without wireless is OFF and I can't turn it on (Realtek RTL8188CE 802.11b/g/n WiFi Adapter). The F12 button stays amber (just pressing and disable / turn off the airplane mode). Wired Ethernet card (Realtek) seems to work OK.

  The wireless card information below. The Device Manager list this adapter and says it's working properly (no warning or 'X'). I've uninstalled and reinstalled the driver in Device Manager. I was not able to find a new version of the driver from the Realtek site. The Windows 10 Network and Sharing Center troubleshooting tool detects any problems.

  The system settings screen (see picture) WiFi won't let me turn on the wireless (if I click on the button to turn the wireless off to, it comes immediately jumps back to the off position)

  

  Manufacturer: Realtek Semiconductor Corp.
  Description: Realtek RTL8188CE 802.11b/g/n WiFi adapt
  Driver version: 2013.12.720.2015

  The fixed!

  I have reset the BIOS to the factory settings. I have no idea why that work. I had read a few posts on the support Forum HP it has worked for other people.

  All the best and happy new year!

• [Pavilion dv5-1215ee] Problems drivers installation after the upgrade to vista ultmaite sp2

  Hello

  first of all it is my laptop that I just bought

  http://h10010.www1.HP.com/wwpc/me/en/Ho/WF06b/321957-321957-3329744-64354-64354-3744212-3877200.html

  as you can see that it comes with Vista home premium SP1.

  I formatted and install Sp2 of Vista Ultmate

  and some drivers that is

  

  When I install. This apear masagge

  

  say this machine is not compatible with the requirement to install this software,

  is it really because SP2?

  can someone give me the missing drivers please...

  help me out here... I'm new and I feel lost and I don't know what to do...

  I also copied 3 DVD collection in the case...

  Thank you in advance.

  ProtectSmart Hard Drive Protection here

• How can I fix mini slow mac after memory upgrade from 4 GB to 16 GB

  I have a Mac Mini (ver 6.2 end 2012, i7 to 2.3 GHz, OS X 10.10.5) that I just put new memory to upgrade to 4 GB 15 GB (Crucial 16 GB = 8GBx2 kit corresponding blades plug their scanner software and HW Apple specs). I use HDMI to my Vizio 32 inch HDTV and now my Mac runs slower for typing, clicks, etc, but the software seems to work fime. I have checjed the "about this Mac" and it shows the memory is available and authorized to use. I also run app "Cleaner" memory and it shows the total memory available and currently in use.

  Then what should I do to solve the slow?

  Thank you in advance fr that all help someone of you provide.

  Ron/Nightstyles

  I run a mini end 2012 with 16 GB.  It's fast... I also have SSD which also provides the spectacular for startup performance improvement and any disk activity.

  Have you checked for any process out of control by using the activity monitor?

  https://discussions.Apple.com/message/20379601#20379601#20379601

  Have you reset the NVRAM and SMC memory since installing the RAM?

  Restart and hold down the command-Option-P-R keys immediately after you hear the startup sound.

  How to reset the NVRAM on your Mac - Apple Support

  To reset the SMC?

  Basically the kindly stop and turn off the power for 10 to 20 seconds.

  Reset the management system (SCM) controller on your Mac - Apple Support

  After resetting these go check the keyboard settings in system preferences...

• Y430A can not boot after memory upgrade

  OS: VISTA HOME PREMIUM 32-BIT
  CPU: P7350
  MEMORY: HYNIX DDR2 667 2GB

  I added a 2 GB Kingston ram on the connector 2

  First of all, it can be the start and connect to windows,

  but after a while, the system of suspension or the SCREEN BLUE DEAD shows,
  He cannot even get into the bios screen when I reboot it

  but it can be boot up if I remove and reconnect the memory

  Sometimes the machine can be restarted and works correctly, except if once I turn it off

  I tried to exchange the slot 1 and 2 with 2 x 2 GB,

  and also replace with 2 x 256 MB Hynix memory.

  but it does not work.

  The new memory is not faulty or is not compatible because it works very well if it autonomous.

  In short, if I install 2 x 2 GB memory, the system may start only once.

  Is it the BIOS problem or it's my mistake?

  Please help and sorry for my bad English.

  Thanks in advance.

  This is perhaps due to the incompatibility of the modules of RAM, working together. If Yes, than to change only the modules will help.

  Also looks like Y510 behavior when it was a fresh model - Y510 all were not able to manage two RAM modules. Update the BIOS helped. For now no new BIOS for Y530/Y430, so will have to wait.

• Cannot install anything but XP after memory upgrade

  My friend had a hp630 running Windows 7 Home Basic, 32-bit. He went to a flea market of computers where they replaced the system memory with two new modules of 4 GB. The system running my end but apparently could not use more than 3 GB of memory by showing that 8 GB has been installed, he wanted a 64-bit system. Given that the system had been there for a few years and accumulated a lot of garbage, we have decided to do a clean install. So we deleted and recreated partition D: with Minitool Partition Wizard and tried to boot from an installation DVD. And here's the problem: no matter how much we have tried different versions of Windows, the only one that worked was XP with AHCI drivers embedded in the disc according to instructions on this forum ( http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/SATA-drivers-for-XP-solution-on... ). both XP sp2 and sp3 XP worked fine. However, Win 7 32 bit, Win 7 64 bit, Win 8 32-bit, win 8 64 bit everything has failed in a similar way: they would go by loading files (Win 7 shows a progress bar while Win 8 showed a logo) and then to reboot (Win 7 without warning, win 8 after a brief demonstration of an error with a sad smiley).

  So the question is, how I approach this problem? Upgrade memory to do the system incompatible with Win 7/8? Unfortunately, the original memory module has disappeared, so I can't go back to the original hardware configuration. Should I try XP 64 bit? I heard that this is not the best system to 64-bit, due to compatibility problems (some have been resolved in later versions). I may try it anyway out of curiosity, but in the meantime would appreciate advice.

  swuser68 wrote:

  Thanks for the quick response!  The machine has Core i3 - 370 M, which certainly is 64-bit capable. Windows ISOs, both legal illegal, don't miss, and device startup doesn't seem to be a problem, either: the computer accepts the DVD I did very well and copied the files from there, but then something went wrong.

  I did the format of the disk as the partition will, but I have not done anything with other partitions. Is - this possibe that Win 7/8 did not like fantasy HP partitioning? There are about 10 GB or partition so hidden, then 2 GB C: drive containing HP tools, then D: to E: and system for data. E: we did oursevles during initial installation for a long time it has so changed their size using MiniTool Partition Wizard. Windows XP has no problem with this disk layout, but perhaps the 7/8 behaves differently?

  Another thing I noted is that F11 at startup has no effect. Is it normal for a model that was sold without any Windows? Or is it possible that it reflects somehow the problem I have with installing Windows?  The absence of function F11 is because you have made changes to the recovery D: partition. Any changes made to the partition will delete the F11 recovery capacity.

  You will find that you have more success if you delete all partitions, then proceed with the installation.

  Let the Windows 8 or 7 Installer create and format partitions of its own during the installation procedure. Normally the C: partition is the system partition,

  I propose the first because you do a clean install instead of use the recovery disks created by the HP recovery media creator utility. Using the recovery media, scripts to create all the required partitions independently and install most drivers as well.

• Tecra M9 - does not start after memory upgrade from 1 GB to 3 GB

  I am trying to upgrade my M9 memory with little success. I bought a 2 GB module which is the same existing brand and spec to the 1 GB module, but the PC will not start no matter what options I try. So far I have tried:

  * Addition of 2 GB for the accommodation of extension from below (3 GB total)
  * Withdrawal of module 1 GB under the keyboard and its replacement by the 2 GB module

  None of these options work. The PC gives no beeps or indications that there is a problem, the led lights on the way to the top, the drive led flashes and then it goes into a wait state. Nothing happens.

  For the record, I bought initially upgraded memory that wasn't an exact match and I am now on my 3rd module suspecting a memory compatibility to be the issue. This current 2 GB module seems to fully match the 1 GB as well as being twice the size. It is:

  HYNIX 2GB 2Rx8 PC2 - 5300 s-555-12

  I am running Windows XP SP3

  The TECRA is a PTM91A Intel Duo T700 CPU 1.80 GHz

  Any help would be appreciated

  Hello

  To me it sounds like the new memory module is not functional or not compatible with the laptop. Otherwise the cell would start without any problem.

  If you bought the memory module in a store, you have to take it back and ask for a replacement.

  I n t have experience with Hynix memory modules. For the upgrade of my laptop, I used Kingston memory and it worked without any problem

• NB100 black screen after memory upgrade

  My NB100 works well with the Samsung 1 GB of memory which was included when I bought it, but when I replaced the screen with a new Kingston 2 GB 667 MHz (2 G/VR667D2S5) doesn't show anything when I turn on the laptop back, even if the LED indicators seem normal and fans inside its normal.

  I tried a replacement memory (same type of Kingston) - still no luck. I put the old Samsung back and the laptop starts fine.

  Any ideas?

  Hey Buddy,

  What NB100 you have exactly? What is the number of exact part of it?

  AFAIK NB100 supports only 2 GB of RAM. This means that you can install the module of 1 GB in each slot, but not a 2 GB RAM module will not work.

  So, if you want only 2 GB of RAM, you will need to purchase an additional 1 GB module because the NB has two memory slots.

• Satellite L100-109 starts a new after memory upgrade

  How can I get my Satellite L100-109 to take the 2 GB of memory is it supposed to be able handle.
  It keeps starting over and over again.

  Can you please provide some info on the RAM modules that you use?
  Usually if you use high quality compatible products, you will not have these problems.

• Re: Satellite L650/07C-boot-loop after memory upgrade

  I have a Toshiba Satellite L650 / 07C - PSK1JA-07C017.
  To get a little more life out of it, I've updated yesterday with a SSD and 8 GB memory.

  The SSDS works perfectly and I have installed OS and all the drivers and software.
  However, the memory causes a boot loops. I returned to the standard 2 x 2 GB memory at the moment.

  With the new memory installed, the computer startup-loops. When you try to start Windows, the computer will appear at the stage of loading Windows (the boot animation) and then restarts.
  I tried to start with the recovery discs, and it arrives at the stage of loading of Windows Setup, and then restarts.
  She will continue trying to start, then by restarting (then repeat), until I turn it off.

  The memory I installed is Corsair CMSO8GX3M2A1333C9 (2 x 4 GB):
  http://www.Corsair.com/cmso8gx3m2a1333c9.html

  For me, it looks like the same specifications that the modules of memory Kingston 4 GB listed on the Toshiba site as being compatible with my laptop:
  http://www.MyToshiba.com.au/products/Accessories/memory/KTT-S3B/4G/accessories

  I found the specs of memory recommended here:
  http://www.LASystems.be/PDF/Kingston/246787/KTT-S3B4G.PDF

  If I go into the BIOS, I see that the memory is detected as 8192KB. The Toshiba site says that this laptop is expandable to 8 GB.

  Is there something I'm missing?
  Is there another step I need to perform when upgrading their memory?
  I don't know why it won't boot with the new memory modules in that I put.

  Thanks for any help you can offer.

  I assume you have the Australian model is not easy to find info on the hardware upgrade. What I can say is that model European uses DDR3 1066 MHz memory modules and 4 GB of RAM compatible a part PA3677U-1M4G number.

  It must be exact model described by microcens.
  I recommend you use the tested and compatible memory modules.

• Satellite L450 - 13G - No WLAN signal after a few minutes

  Hello. I just bought a L450 13 G with Windows 7 pre loaded.

  I noticed that a lot of times drops wifi connection. It starts as an excellent signal and then suddenly fades to no signal after a few minutes. I can't get it remains connected, if I'm in the same room or the next day. I have also a few years L or U 200 (I think) and it remains connected wherever I am at home.

  What could be the problem?

  Hey Buddy,

  I assume you are using the preinstalled version of Windows 7. Is this good?
  If so try to update the WLAN driver. If you are looking for your laptop model, you will find the latest version on the Toshiba site.

  In addition, check the configuration of the router. If you use a MAC address filter, try to disable it. Try another encryption and password encryption.
  Also check the firmware if you use the most recent one.