I have a stop to boot error

Similar Questions

• After upgrading RAM, computer stops and gives error when restarting: "DISK BOOT FAILURE, INSERT SYSTEM DISK".

  Original title : OFFICE XP STOPS (MESSAGE of ERROR)

  I get the message "DISK BOOT FAILURE, INSERT SYSTEM DISK". I just added more memory to my 512 RAM. I USED MY XP TO REBOOT DISC, BUT THERE ARE ALWAYS AFTER PRESSING THE KEY 'R '. ONCE IT STARTS AND SE PAST JUST STOPS AND THE ERROR MESSAGE IS POSTER AGAIN UPWARD. I HAVE THE SAME 'MSCONFIGED' IT NORMAL TO SELECTIVE. I WAS ABLE TO GET INTO SAFE MODE, BUT NOW IT WON'T. I GET JUST THE ERROR MESSAGE.       > WHAT AM I DOING WRONG

  Hello

  You can view these methods:

  Method 1: As a first step, check to see if the hard disk becomes detected or listed in the Basic Input/Output system (BIOS). Also, be sure to change the boot order in the CMOS settings so that thehard drive is the first on the list.

  Note: To learn how, see the documentation provided with your computer or contact the manufacturer of your computer.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

  Method 2: If the manufacturer has installed the Recovery Console on your computer, perform the check disk to fix this.

  At the recovery console command line, type:

  Chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  For more information, see:

  How to perform disk error checking in Windows XP

  Chkdsk

• I can't open my email IE account - it starts then stops and an error pop up My IP tried but it's IE-I have windows XP

  After a Windows Update - the next morning I couldn't open IE to get my emails. It starts to load and then stops. An error message appears that says: an unknown error has occurred. Account ' pop - server.cfl.com. Server "pop - server" pop protocol: pop3, port110 Secure [SSL}: no, error # Ox800co133.]    I called my provider IP-BRIGHT HOUSE and the Department tech ran me through a bunch of hoops and finally said the problem was with Windows. I called the MICROSOFT HELP #1 800 642 - 7676 # and tersely told they do not have XP support, except for free fees. $ 59.95.  The fact that I am a person aged 68 year on a small pension does not stage a bite person and $60.00 for a problem that began after only an automatic update did not seem to matter either. If anyone can help I would know you more. I depend on my e-mail with the requirements of the order and stay in touch with my friends and my daughter-son. Thank you very much. Cordially - Donald

  Hi Donald,.
  Here is a walk through one of our best community members Bruce Hagan.
  I think that this is your specific problem.

  Error number: 0x800C0133 = a corrupt Inbox.

  Move any message you want to save to a local folder that you create. Then, remove the problem of Inbox as follows.

  Tools | Options | Maintenance | Store folder will reveal the location of your Outlook Express files. Note the location and navigate on it in Explorer Windows or, copy and paste in start | Run.

  In Windows XP, Win2K & Win2K3 the OE user files (DBX and WAB) are by default marked as hidden. To view these files in Windows Explorer, you must enable Show hidden files and folders under start | Control Panel | Folder options | View.

  With OE closed, find the box of Inbox.dbx and delete it. Another will be created automatically when you open OE.

  General precautions for Outlook Express:

  Do not archive mail in the receipt or sent items box. Create your own user-defined folders and move messages you want to put in them. Empty the deleted items folder daily. Although the dbx files have a theoretical capacity of 2 GB, I recommend all a 300 MB max for less risk of corruption.

  After you're done, followed by compacting your folders manually while working * off * and do it often.

  Click Outlook Express at the top of the the folder tree so no folders are open. Then: File | Work offline (or double-click on work online in the status bar). File | Folder | Compact all folders. Don't touch anything until the compacting is completed.

  Disable analysis in your e-mail anti-virus program. It is a redundant layer of protection that devours the processors and causes a multitude of problems such as time-outs and account setting changes. Your up-to-date A / V program will continue to protect you sufficiently. For more information, see:
  http://www.oehelp.com/OETips.aspx#3

  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/error-ox800co133/849906f8-0893-40AA-BA8B-4ff7b9c6f279?auth=1

  Let us know if you have any questions.
  B Eddie

• is it possible to set up a dual boot, so I don't have to stop, and then pass the SATA cables that I boot to change?

  Original title: Dual boot

  My XPpro on a former player, was upward. then, I got another new drive, installed Win7Ultimate.  Well, I got the OLD disk works with XP on it.  But, some of these apps DO WORK not on Win7.  so, at least for now, I have two drives installed on the same computer.  is it possible to set up a dual boot, so I don't have to stop, and then pass the SATA cables that I boot to change?   Operating systems already are on 2 different disks.

  Hello

  How to set up a Dual Boot Installation with Windows 7 and XP
  http://www.SevenForums.com/tutorials/8057-dual-boot-installation-Windows-7-XP.html

  Definitive dual-booting guide: Windows 7, Linux, Vista and XP step-by-step
  http://apcmag.com/the_definitive_dualbooting_guide_linux_vista_and_xp_stepbystep.htm

  Dual Boot computer preinstalled Windows 7 with XP
  http://www.howtogeek.com/HOWTO/8790/dual-boot-your-pre-installed-Windows-7-computer-with-XP/

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• When I try to install v.6, CD or as copied photoshop folder on the desktop, the installation stops with "Error1310-error to write to the file. Make sure you have access to this directory.

  When I try to install v.6, CD or as copied photoshop folder on the desktop, the installation stops with "Error1310-error to write to the file. Make sure you have access to this directory.

  Please see:

  Error "1310: error writing to the file: C:Config.Msi...» » | CS4 products

  I hope this helps.

  Greetings

  Megha Rawat

• An unexpected error has occurred and the application will have to stop

  Hyperion 11.1.2.2, new environment.
  
  When you try to configure the EPMA database, Configurator crashes with the error "an unexpected error has occurred and the application will have to stop."
  
  Customer has configured the database of EPMA with success during the first time.
  
  Their DBA deleted database EPMA and re-created the database with the same name. Now, they are trying to configure EPMA data base and the Configurator crashes with the error mentioned.

  I had the same error after applying a few patches EPMA (.301 ou.302)
  Here's what Oracle provided support. This solved the problem for me to use the older, bigger jar file

  ----------------------------------------------------------------------------------------------------------------------------------
  Fix Oracle can be broken by the jar file that located awbconfig.jar
  d:\oracle\Middleware\EPMSystem11R1\products\Foundation\BPMA\Common

  There are missing classes in the patched version, latest of this pot

  To correct the configuration tool, you can make a copy of that existing pot and replace the old version uncorrected. To find the old version research
  \oracle\Middleware\EPMSystem11R1\.patch_storage\ to AwbConfig.jar

  To confirm this, look at the size of the current pot and the oldest pot - the news is 158 k and the former was 317 k - obviously a new miss some classes.

• Satellite L505-13Z - BOOT error

  Hi all, I have a Satellite L505-13Z. After the hard drive recovery, something went wrong and I had only the F12 page.
  I used the recovery DVDs. It worked for an hour to install win7, then he did a reboot and I saw the windows screen, so that it starts again and stopped working: whenever I turn it on, I have the F12 screen, choose a place to start. Hard drive is detected, but if I choose what it I got the "Boot error" and back to the same page.

  I would try Hiren boot to check if the hard disk is OK or not. How will I know if it's only the hard drive or something else?

  Thank you

  UPDATE.
  I used a bootable cd with Hiren and each test on hard disk and RAM are OK, no errors.
  I inserted the DVD to see if he had the option to repair an installation, but do not, so I installed again. In the end, we asked me to remove the DVD and restart; I did and I went to loop: win 7 was updating registry, reboot, win 7 has been updated to register...

  I wondered if the DVD has been damaged, but is no way to download from microsoft, a Windows 7 copy, because when I insert my response series is to ask the supplier...

  What can I do?

  Posted by jazzrock71
  

  Hi all, I have a Satellite L505-13Z. After the hard drive recovery, something went wrong and I had only the F12 page.
  I used the recovery DVDs. It worked for an hour to install win7, then he did a reboot and I saw the windows screen, so that it starts again and stopped working: whenever I turn it on, I have the F12 screen, choose a place to start. Hard drive is detected, but if I choose what it I got the "Boot error" and back to the same page.

  I would try Hiren boot to check if the hard disk is OK or not. How will I know if it's only the hard drive or something else?

  Thank you

• Stop: c000021a {fatal error} the windows logon system process ended unexpectedly with the status of 0xc0000034 (0x00000000) (0x00000000) need help please system does not start

  Hi my HP Compact computer running with windows Xp professional recently had security tool, antimelware doctor and I kind of have got rid of him, he also put some viruses on the winlog thing and I could not get rid of it with antivirus software that I don't know the name of, Malwarebytes' Anti-Malware and AVG 2011 I did a scan antivirus in safe mode with AVG(in command prompt mode) and he put a bunch of virus the virus volt, I'm out there and there was a running called 2008 command prompt and I clicked on output and it says that this program is not complete (or something similar) save all unfinished work before going out and me did not run this command prompt , so I left Malwarebytes' Anti-Malware and avg, then I restart my computer and we get the blue screen of death say stop: c000021a {fatal error} unexpectedly finished process windows logon process system with the status of 0xc0000034 (0x00000000) (0x00000000) system will reboot, and whenever it restarts, it says the same thing, I can't use safe mode cause it resets and starts normally any help pls I have files I need this computer?

  You can create a bootable XP Recovery CD of Console and replace the file, but it may be easier for you to make boot CD of a Hren.

  When you start the Hiren's CD, choose the XP Mode of Mini and it has an interface in XP style Explorer where you can find and replace the winlogon.exe suspicious or missing file.

  There should be a copy of winlogon.exe here:

  c:\Windows\System32\dllcache

  Rename your current c:\windows\system32\winlogon.exe file (if it exists) and copy / paste the replacement of c:\windows\system32\dllcache.  If you do not see here, search your HARD drive and find one.  Another possibility (depending on your environment) is c:\windows\ServicePackFiles\i386, or c:\i386 d:\i386...

  You just need to replace the file winlogon.exe somehow.

  When you are finished replacing, restart as usual (remove the CD bootable of course).

  With the help of Hiren, you can also copy offshore on an external device (USB key or HARD drive), all personal security files.

  Do you have a Hiren BootCD you can download here:

  http://www.hirensbootcd.NET/

  On the left, click on download, scroll down, choose the latest version, the download link is a little hard to see.  It is at the bottom of the page, above the drop for older versions and looks like this (click this component to download the ZIP file):

  Direct HTTP mirror + Torrent, Torrent Magnet

  Click the "Live HTTP Mirror" link to start the download and save the ZIP file on your desktop of somewhere that you can remember.

  The ZIP file is large, so the download will take probably some time to complete.  Then unzip the download to extract the Hirens.BootCD.ISO file that will be used to create your new bootable CD.

  Create a bootable CD. ISO file is not the same as simply copying the. File ISO onto a blank CD.  You must use software that includes how to burn a. ISO to a CD to create a bootable CD.

  File ZIP the Hiren is the file BurnToCD.cmd that you can double-click to launch it.  The BurnToCD.cmd will use the file BurnCDCC.exe to burn the. ISO file onto a blank CD using your existing CD burner.  You can also use your own burning software as long as your software is able to create a bootable CD. ISO file.  More modern burning programs can create a bootable CD. ISO image.  Create a CD from an ISO image bootable is not the same as just the file on a CD burning.

  If you need a simple and CD burning, this is a free software popular software:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your new bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.

  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When starting on the Hiren's CD, you will see a menu of options.  Choose Mini XP.  It will appear while Windows is loading and you will be presented with a desktop computer that has the look and feel of the interface of Windows Explorer, you are already accustomed to using.

  Using the Mini XP, you can access Internet, maneuvering around your system, search for files, copy files, replace the files and run the scans for malware, edit the text files (like the c:\boot.ini) etc.

  There are dozens of free and useful tools included in the CD that can be used to repair your system or copy your important personal files on another device (like a USB device or an external drive) in the case where you just give up and decide to reinstall your XP (I hope that you will not make this decision).

  Do, or do not. There is no test.

  I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• Restart problems, error Disk Boot error, if please install disk and press a key

  Original title: problems of Reboot

  When I restart my computer it say "Disk Boot error, if please install disk and press a key:?"

  Hello

  1. you remember to make changes to the computer before this problem?

  2. have you changed the BIOS boot device?

  3. What is the brand and model of the computer?

  This could be related to:

  · Startup options is not correctly defined in the BIOS

  · A non bootable CD is in your CD player

  · You don't have any boot device

  · You have installed a new hard drive

  · The hard drive is not properly connected

  · Your system files have been infected

  Change the boot order in the CMOS (BIOS) settings so that your disc is the first in the list.

  a. restart the computer.
  b. new computers often display a startup (or boot) menu. In the start menu, choose "Configuration of the BIOS," or "BIOS settings," or something similar.

  Procedures vary depending on the manufacturer of the BIOS. Usually, you must press a key (for example, F2, F12, DELETE, ESC) or a combination of keys immediately after you
  turn on your computer but before Windows starts. If the Windows logo appears, you must try again by waiting until the Windows logon prompt appears, and then stop and restart your computer again.

  c. the BIOS configuration screen appears. On the BIOS Setup screen, choose the option called "Boot order" or something similar. Startup command settings can also be saved
  under "Advanced settings" or something similar.
  d. Select your drive from DVD or USB drive as first boot device.
  e. restart your computer and see if the problem is resolved.

  
  BIOS WARNING: modification of the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• Stop: 0x0000007B Inaccessible_boot_device error

  I have converted a server that has windows 2000 adv server with Service Pack 4 (series Dell 8450 with 4 processors). I used Vmware converter 4.0 to convert VM. Earlier there not so many times when I choose preservce & SCSI options. It worked he successfully converted VM when I choose the IDE. but ran only to vmware server 2.0. As IDE is not supported in ESX 4.0. Now we buy license for Vsphere and want this physical machien (dell 8450) in ESX 4.0. I tried convert the machine several times, but when he reached 97%, it fails on the reconfiguration all the time. so I deleted the reconfiguration option before converting and converted files in three different ways. preserve, scsi, and IDE.  Now when I moved in the data store and configured with VM one by one. (IDE na not work since the beginning). two other cases, defective error all the time below.

  Stop: 0x0000007B Inaccessible_boot_device error

  It starts well windows 2000 page appears after the bar comes in the middle of this error. I tried all methods to run this VM as converting Bus & LSI controllers. ESX 4 gives four option BSU, LSI, Pará and the fourth I don't remember right now. I tried all 4 ways chaning to operate but always same error. I also tried to convert the Vmdk files with vmkfstools-i option. But still, things went wrong. I don't know what I'd do. Can anyone help. For your reference, I am pasting vmx for one of the below vmx files. Appreciate if someone told me step by step or atleast guide new way to make this file work.

  VMX file:

  #! / usr/bin/vmware

  . Encoding = 'UTF-8 '.

  config.version = '8 '.

  virtualHW.version = "7".

  pciBridge0.present = 'TRUE '.

  pciBridge4.present = 'TRUE '.

  pciBridge4.virtualDev = "pcieRootPort"

  pciBridge4.functions = '8 '.

  pciBridge5.present = 'TRUE '.

  pciBridge5.virtualDev = "pcieRootPort"

  pciBridge5.functions = '8 '.

  pciBridge6.present = 'TRUE '.

  pciBridge6.virtualDev = "pcieRootPort"

  pciBridge6.functions = '8 '.

  pciBridge7.present = 'TRUE '.

  pciBridge7.virtualDev = "pcieRootPort"

  pciBridge7.functions = '8 '.

  vmci0. Present = 'TRUE '.

  NVRAM = "Buslogic.nvram."

  deploymentPlatform = "windows".

  virtualHW.productCompatibility = "hosted".

  unity.customColor = ' | ' 23C0C0C0 ".

  Tools.Upgrade.Policy = "useGlobal".

  powerType.powerOff = 'soft '.

  powerType.powerOn = "default".

  powerType.suspend = "hard."

  powerType.reset = 'soft '.

  displayName = "Buslogic".

  extendedConfigFile = "Buslogic.vmxf".

  floppy0. Present = 'TRUE '.

  numvcpus = '2 '.

  scsi0. Present = 'TRUE '.

  scsi0.sharedBus = 'none '.

  memsize = "1024".

  scsi0:0. Present = 'TRUE '.

  scsi0:0. FileName = "Buslogic.vmdk".

  scsi0:0. DeviceType = "scsi-disk" hard

  scsi0:1.present = 'TRUE '.

  scsi0:1.filename = "Buslogic_1.vmdk".

  scsi0:1.DeviceType = "scsi-disk" hard

  ide0:0. Present = 'TRUE '.

  ide0:0.clientDevice = 'TRUE '.

  ide0:0. DeviceType = "cdrom-raw"

  ide0:0.startConnected = "FALSE".

  floppy0.startConnected = "FALSE".

  floppy0.clientDevice = 'TRUE '.

  ethernet0. Present = 'TRUE '.

  ethernet0.wakeOnPcktRcv = "FALSE".

  ethernet0.networkName = 'network of the VM.

  ethernet0. AddressType = 'generated '.

  Serial0.present = 'TRUE '.

  Serial0.yieldOnMsrRead = 'TRUE '.

  Serial0.filename = ' / dev/ttyS0 ".

  serial1. Present = 'TRUE '.

  serial1.yieldOnMsrRead = 'TRUE '.

  serial1. FileName = ' / dev/ttyS1 ".

  guestOS = "win2000advserv."

  UUID. Location = "4 d 56 70 3 b a9 4A a4 58-30 46 87 30 6 c d4 2nd b1.

  UUID. BIOS = "4 d 56 70 3 b a9 4A a4 58-30 46 87 30 6 c d4 2nd b1.

  VC. UUID = "2nd 52 02 4 b ca CF e0 b9-13 17 bf 77 6 d 59 f6 ed.

  SCHED. CPU. Affinity = "all".

  sched.mem.Affinity = "all".

  ethernet0.generatedAddress = "00: 0C: 29:30:6 c: d4.

  cleanShutdown = "FALSE".

  Replay.Supported = "FALSE".

  sched.swap.derivedName = ' / vmfs/volumes/4a4c71d8-3013156c-1d94-001b7802d5f6/Buslogic/Buslogic-fe45f1d4.vswp '.

  scsi0:0. Redo = «»

  scsi0:1.redo = «»

  vmotion.checkpointFBSize = "4194304".

  pciBridge0.pciSlotNumber = "17".

  pciBridge4.pciSlotNumber = "21".

  pciBridge5.pciSlotNumber = "22".

  pciBridge6.pciSlotNumber = "23".

  pciBridge7.pciSlotNumber = "24".

  scsi0.pciSlotNumber = "16".

  ethernet0.pciSlotNumber = "32".

  vmci0.pciSlotNumber = "33".

  ethernet0.generatedAddressOffset = '0 '.

  vmci0.ID = "-2026869548".

  hostCPUID.0 = "0000000a756e65476c65746e49656e69".

  guestCPUID.0 = "0000000a756e65476c65746e49656e69".

  userCPUID.0 = "0000000a756e65476c65746e49656e69".

  hostCPUID.1 = "000006f6000208000004e3bdbfebfbff".

  guestCPUID.1 = "000006f600010800800002010febfbff".

  userCPUID.1 = "000006f6000208000004e3bdbfebfbff".

  hostCPUID.80000001 = "00000000000000000000000120000800".

  guestCPUID.80000001 = "00000000000000000000000000000800".

  userCPUID.80000001 = "00000000000000000000000120000800".

  evcCompatibilityMode = "FALSE".

  Morning,

  I suggest to change the to the BusLogic one SCSI adapter and then using BartPE to make sure that the correct drivers are loaded in the operating system. This can be done by going to http://www.nu2.nu/pebuilder/ and then adding the Fix-VMSCSI (http://www.rtfm-ed.co.uk/?page_id=174) plugin to load the drivers in your Windows 2000-based computer. This does two things at once: loads the BusLogic driver and modifies the Windows registry to boot from it.

  Yell if you need any other instructions, otherwise I hope this helps.

  Kind regards

  Glen

• My pointer freezes, so I have to stop & restart for 20% of the time. How can I fix it?

  My pointer freezes, so I have to stop & restart for 20% of the time. How can I fix it?

  Hello

  • When the issue started?

  Method 1:

  Step 1: Check if the problem exists in Mode without failure.

  See the article below for Safe Mode steps in Windows XP.

  A description of the options to start in Windows XP Mode: http://support.microsoft.com/kb/315222

  Step 2: If the problem does not persist in Mode without failure, then try to clean boot.  You need to perform a clean boot to find the program that is causing and then disable or remove.

  How to configure Windows XP to start in a "clean boot" State: http://support.microsoft.com/kb/310353/en-us

  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2:

  Also check the logs in Event Viewer for the recent activity on your computer and check.

  This article describes how to use Event Viewer to view and manage the event logs in Microsoft Windows XP.

  How to view and manage the event logs in Event Viewer in Windows XP: http://support.microsoft.com/kb/308427

• I have to stop twice to stop

  I have to stop twice to stop

  Sorry for the delay in responding

  Well, I loaded the heap use cleaner and that makes a difference.  It works some time in milliseconds and sometimes upward is a black cmd box and takes 20 seconds or more... but then the machine stops.

  Unfortunately it seems that I have to run it whenever I stop

  However - other machines in the House are also affected - and yes they are all use Norton... but almost at the same time as we have updated Norton, we bought a NAS,... and each user has an account on the NAS.  I wonder if this Seagate NAS has got something to do with the problem.  I tried a few tests to not to use the SIN at all and see if that makes a difference - and in any scientific way, it seems that use NAS is proportional to both the clearer CMD bunch TextBox...

  Alas, the problems don't stop there.  Since 2-3 weeks - I now remove the power cord from the PC before it turns off.  This problem started almost exactly at the same time that I started to use the cleaner job... may be linked to the United Nations, but it seems too narrow a time scale... So I'm not deploy the clearer pile to the other machines (yet)

  No need to apologize but I don't thank you for review.

  In regards to the user profile hive Cleanup utility, you don't have to run continuously. Once installed it automatically runs in the back ground whenever your computer is started.

  Unplug the computer, it is the equivalent of a closed hard and can be harmful to your file system. I recommend that to perform a clean boot following the instructions on the link below. It is essentially a process of elimination method to determine what software is suspended at the stop. I still recommend that you only perform the manual steps as opposed to guided help.

  How to configure Windows XP to start in a "clean boot" State

  I do not vote for me I'm not here for points. If this post helps you, vote. Visit my forum @ http://repairbotsonline.com/

• How to fix STOP: C0000221 unknown error

  Hello

  I get the following error - STOP: C0000221 unknown error. The message appears for 3-4 seconds a blue screen then the screen goes black and I get the Windows Error Recovery screen. If I choose to start windows normally or in safe mode, I always get the blue screen with STOP: C0000221 message. Therefore, I am locked into this cycle of error messages and I can't really use all the fixes I found in the forums. What should I do?

  In early startup options (Safe Mode) have you tried other options like the "last known good configuration?

  If that wouldn't work, see this article if this can help:

  How to fix Ntdll.dll errors
  http://pcsupport.about.com/od/fixtheproblem/a/ntdlldll.htm

  Since you cannot start the computer, you can start your troubleshooting on number of article 8, which is "Test your memory of the damage." If you cannot perform the memory test, and you have 2 sticks of RAM, skip a turn in turn and check or you can use/borrow RAM from a known working computer.

• Toshiba Satellite A135 laptop: 0xc000000f - Windows Vista Boot error - &#62; recovery disk does not work, can't get the PC to boot.

  I have read all the info out there and tried many things including using the provided by Toshiba, Vista recovery disks

  I can't go down the screen of boot error, although no matter what I try.

  Is my drive into two partitions, and I am ready to sacrifice one of them if necessary to get the computer to boot.

  Is there a way I can enter directly into the computer and reinstall windows?

  I'm not a pro, then simple instructions are the best.

  THX

  Hello

  1. don't you make changes to the computer until the problem occurred?

  2. What are the troubleshooting steps you tried to solve the problem?

  3. the problem occurs in safe mode?

  4. don't you try to do the Startup Repair?

  I suggest you try the steps from the link below and check if it helps.

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows: http://support.microsoft.com/kb/927392

  Hope this information is useful.

• Windows vista service pack 2 [BOOT ERROR! Oxc0190036 1187/59291 (Faultrep.dll)]

  Help, please!

  I use a sony viao laptop AR71M with windows vista home premium. I tried to update on windows service pack 2 panoramas, but get a boot error after installation
  !! Oxc0190036 1187/59291 (Faultrep.dll)
  I have tried everything I know, but it didn't budge. I had to restore my system several times so that I can continue to use my laptop.

  Hi DaveCole,

  I suggest you try the methods mentioned below and check if it helps.

  Method 1: Start Windows Vista with the Windows installation media, and then use the repair feature.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Method 2: Start the system in safe mode and then use the system restore feature.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 3: Follow the provided article.

  How to troubleshoot Windows Vista and Windows Server 2008 service pack installation issues

  http://support.Microsoft.com/kb/947366

  Method 4: No detection system file checker (SFC).

  http://support.Microsoft.com/kb/929833