imports of regedit between two machines

Similar Questions

• Cannot use Office to distance between two machines to windows 7

  what I tried listed below:

  the other ping ok

  in vain telnet 3389 mutually

  Telnet itself 3389 ok

  netstat - year also list port 3389 is listening

  both machines are in the same network of 10.0.0.0/24, whatever cable or using a wifi connection, remote desktop never works. But I can use both of the two machines to connect to a server of windows 2008 with no problems.

  I tried to trun, disable the firewall of windows (profile), no luck; tried to turn off windows firewall, no luck; attempted to create a rule to allow access port 3389 from any ip address both of the machines, no luck.

  I have tried everything I can, no chance, no chance. who can help with this strange problem?

  Hello

  I suggest you to refer to these items and check the status.

  Remote Desktop connection: http://windows.microsoft.com/is-is/windows7/products/features/remote-desktop-connection

  Remote Desktop connection: frequently asked questions: http://windows.microsoft.com/is-is/windows7/remote-desktop-connection-frequently-asked-questions

  You can view this issue in the Windows 7 IT Pro TechNet Forums: http://social.technet.microsoft.com/Forums/en-US/w7itpronetworking/threads

  Thank you.

• Netem VM between two virtual machines? Is this possible?

  Hello

  I would use netem on a linux VM between two other virtual machines to simulate latency. Between Netem needs a machine with two network cards that he can fill. I've set up a VM on vSwitch0, a virtual machine on vSwitch1 and then an another VM with two network cards, one on each vSwitch. I thought that I create this box for use Netem and imitate and then between the two.

  Has anyone ever done something like this? I ran into a ton of problems and want to know if people have tried.

  I got it working by following these steps:

  1. create the computer virtual one with a NETWORK card on vSwitch0

  2. create a VM with a NETWORK card on vSwitch1 b

  3. create a VM n with a NETWORK card on vSwitch0 and vSwitch1

  4. set the port groups to vSwitch0 and 1 for the "Promiscuous" mode accept (from the default of rejection)

  5. set the n, a centOS VM VM for a networking interface using two network cards

  Note: maps network of VM's and b VM were located in the same subnet.

  Once step 5 start working and traffic exchange VM has and through VM n. b I have experienced a strong delay 5ms ping where there was a<1 ms="" delay="" on="" ping="" when="" vm="" a="" and="" b="" were="" on="" the="" same="" vswitch.="" i="" came="" in="" the="" next="" day="" and="" the="" delay="" was="" gone.="" no="" idea="">

  All the tricks to bypass and netem being by default in the installation of CentOS 6.4, I was able to establish conditions as the loss of delay and the package on the transport between the VM and VM n and b degraded as desired.

  The reason that I wanted this to be complicated as it is I can take a virtual machine of vSwitch 0 and pop in vSwitch1 and all of a sudden traffic to and since it undergoes degradation due to the conditions imposed by the bridge n Netem the VM configuration.

• Move a virtual machine to turn off between two hosts, shared storage

  Dear Experts,

  Please guide me for the next case. There are two hosts of Esxi, host 1 is Esxi 4.0 and host 2 is Esxi 4.1. There are store data SAN storage that is visible to both hosts.

  I watched solard winds VM monitor utility that hosting 2 consumes 90% of the memory while its processor is ok. On host 1 is normal. So, I want to spend only a few VM of to host 1. So please correct me if what I think are OK. I will turn off the virtual machine to be moved from host 2. Then I it will remove host 2 inventory. Then on host 1, I'll go to the data store in the folder that VM and do a right click on the file 'say add to the inventory' and now I'm going to see this virtual machine in the inventory of the host list, just turn on and everything is perfect, is this correct?

  Second question on the same hosts, there are a few other data stores that are visible to a host. As if this is the case there is a virtual machine on a data store that is visible to host 2 and I want to spend this VM to host 1 to reduce load on host 2. How to move this virtual machine because this data store is not visible to host 1? Will I have to copy this VM files in a data store that is visible to host 1? If YES then what real required to copy files?

  Kindly help me.

  Kind regards

  From your description I m assuming that you use not vCenter to manage your hosts, correct?

  If you have a store of data shared between two hosts you can do the steps you descripte (power off, remove the inventory etc.).

  For your second case there are several ways, it depends on where you want to place the virtual machine in the future. Wouldn't be on the shared data store that already exists or can in the local data store on the other host? Or is there an option to also display the current data store to host 1?

  If you want to copy the VM files copy the whole folder of it.

  Kind regards

  Mario

• Network sharing between two virtual machines to XP

  Looks like it should be easy, but for some reason I can't make it work.  MacPro with two XP virtual machines running.  I want to share some files between virtual machines.  I tried to put them both in Bridge mode, but I was unable to ping each other.

  Is there anything else I need to do?

  I'm not too familiar with sygate.  As you have discovered, yes Windows Firewall allows for sharing of files across, but it disables ping responses (unless you enable it manually).  If you have Sygate running on one of these virtual machines, I would disable the windows one if you don't have multiple firewalls on the system for you in trouble...

  Open ports 135-139 (TCP and UDP) and also open 445 (TCP and UDP).

  Don't forget to assign points for correct or helpful answer.

• How to share XP Home Edition and XP Professional edition between two different machines?

  I have the OEM installation DVD and modes of action with product codes for each edition (XP Professional SP2 & XP Home Ed SP2).

  I installed and activated them on two separate computers (a Mac Mini (XP Pro) and a MacBook Pro (XP Home) both running under Parallels). Now, I want to Exchange editions beween the two machines. How to activate one-"Windows XP on each machine, so I can re - install on another machine?"

  Thank you. Sayling

  You cannot "turn off" Windows. Because these operating systems are running in virtual machines, you can simply move the virtual machines on the desired computers and start them, by removing the 'old' of their respective computers later. Usually, when I opened a back-up-and-move virtual machine with VMware Fusion/Workstation I get a message in the sense of "was this virtual machine, copied or moved? I say always "inappropriate" and VMware makes the necessary adjustments. Parallels will probably do the same thing. You can't even get a prompt to re-enable installs it XP, but if you do, it's no big deal. If the automatic activation does not work it just use the phone option, wait for a human to come on the line and tell them that you have uninstalled XP and reinstalled on the same machine and it is installed on a single computer. Technically, you will be in violation of the LICENSE agreement given that the license for an OEM version is linked to the computer on which it is first installed but things will still work. MS - MVP - Elephant Boy computers - don't panic!

• How can I make a network between two databases?

  Hello all;
  

  Is going to set up oracle 10 g - (

  I try to Exchange data between two different databases.)
  Each database is configured in different operating systems.
  
  For ex: a database of windows XP (separate virtual machinne)
  a database of linux rhel (separate virtual machinne)
  
  I'm waiting for suggestions...
  
  Thank you...
  
  Published by: 969352 on March 19, 2013 10:04

  969352 wrote:

  What virtualization product do you use?

  * #* vmware - toolbox - cmd - v
  8.1.3.9911 (build-203739)

  VMWARE product information:

  Version: 7.0.0 build - 203739

  Ok. You will need to ensure that the ip addresses you assign to your virtual machines are in the same subnet that the adapter created by the installation of vmware. Once you get the fixed basic network installation, you can treat these virtual machines like any machine in your data center. Forget the vm console and access it exactly as you would for any remote server - putty for the Linux and Windows Remote Desktop to the Windows machine.

  To a prompt on the host computer, post this:

  c:> ipconfig -all
  

  You will get feedback on multiple net cards, of which two are identified as with vmware - vmNet1 and vmNet8. Note the IP addresses of the two. We'll need later.
  You'll also need to know how you have configured the network cards on your virtual machine - NAT, bridged, hostonly?

  Note that these issues are out of scope for this forum. I don't mind helping, but I don't have an installation of vmware for details of the reference.

  Which have really tried to do? ( Data transfer )

  I tried to Exchange data from windows to linux DB database

  It's pretty vague. Exactly how did you try to "Exchange data"? A SQL using a db_link? import/export? Pigeons?
  >

  Where are you stuck?

  I don't know, how to set up the ip address and the necessary information for the windows database.

  Configuration of an IP address is purely a matter of admin OS and out of range for this database forum.
  Google is your friend, but only if you use: [url http://lmgtfy.com/?q=configure+windows+ip+address] http://lmgtfy.com/?q=configure+windows+ip+address
  >

  It's all Edstevens... Thank you...

• How can I set sharing of files between two iMacs?

  I want to set up the sharing of files between two iMacs in my office. Both work on iOS 10.11.3 and both are on the same WiFi network. I'll Finder, select the name of the other computer under 'sharing', then ' connect under... ". ", and then enter the name and password of the other computer. On a computer, I am told that it is connected with each other. However, the second computer always shows "the connection failed". I tried the 'Registered user' choice of "Guest" and "using Apple ID", but none will establish the connection. There must be something obvious that I'm missing, but I wasn't able to find out. I also tried to see if they would communicate with Bluetooth. Bluetooth screens on each computer show the the other is detectable by the proper name, but is never establish a connection.

  Connect to the same network.

  Enable sharing of files on both machines.

  Select the items to share on each machine and check the box in the dialog box information.

• E/s Ethernet between two computers

  I have two computers running labview. I'm trying to generate a signal on one and read it on the other. Connection between two computers is ethernet. The problem is that NEITHER MAX cannot detect a network device. I have ping successfully the signal sent to the computer via the command prompt. Any ideas on why MAX can't detect the signalling computer?

  Try running the examples on the same machine. If you can't find the example works between two instances of the application of different on the same computer, then you certainly won't operate on two different machines. Once it works, try using the IP address instead of the host name of the computer. If still no luck, try disconnecting all other networks on both machines.

• Measure the time between two digital pulse

  Hello

  For a non-critical calendar application, I need to measure the time interval between consecutive TTL pulses, ranging from the order of 0.5 s for a few seconds, with a low accuracy of +/-10-50ms. The interval being measured varies between the rising edge of the first pulse and the front of the next and so on.

  I have several input lines I need to deal with. Because it's a critical machination low cost, I don't want to use digital counters for each line, so I work with an acquisition of data USB6008 and have connected the input rows TTL on the digital inputs of the device. Avoiding will be sufficient.

  I found a good example of VI on discussion forums that does almost the same thing, only it uses instead of the DAQ Assistant user input. The VI works including the time the program going on in a while loop. I replaced with the DAQ Assistant output (a channel) user input in the hope that it is still work.

  

  When I run the program in "run once" mode, it seems to work perfectly. However, in "continuous run" it measures only a very small interval, probably just the time between two samples.  I think it has something to do with the help of a while loop in combination with the DAQ Assistant. Anyone who has any suggestions how to solve this problem?

  Thank you!

  OK... first of all, you should never use the button "run continuously.  I wish that NEITHER would be to eliminate it, but told me that it is sometimes useful for debugging.  If you want your program to run over and over again, use a while loop with a stop"" button.

  If I'm reading your code correctly, you make your initial moment, and then collect data from data acquisition.  When one of the channels is "T", you stop your loop and the end time of capture.  (By the way, why you convert your table to a cluster?  Why not just index the appropriate channel in the table directly?)

  Since you want to capture the time between two consecutive pulses, you need to know when a transition has occurred... i. e when your digital line went from F (no pulse) to T (pulse start).  This will give you your forehead.  Right now, all you're doing is looking for a value T - so you have no way of knowing if you are looking for to the previous impulse again, or a new impetus.  You also burn 100% of your processor with the way you have your programme in place.

  You need a small loop delay so that your VI is not 100% of your hogs CPU time.  Given that you can live with an accuracy of 50msec, what I suggest that you use.

  See attached picture for you give an idea of how to implement.  He will probably need some refining operations, but it should point you in the right direction.

  

  I hope this helps.

• The way of writing to a wireless bridge between two different routers.1:broadband and dir 2:dlink 605 l

  I want to bridge.and wireless I can't do that... Please send me how to write to a wireless bridge between two different routers.

  1:broadband
  and
  2:Dlink dir 605 l,

  Hi Mohammed Ehsan Jourah,.

  Thanks for posting the request in the Microsoft community forums.
  I understand that you need to know how to make a wireless bridge between two different routers

  What version of the operating system is installed on the computer?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  You can try the steps at the bridge between two different routers wireless.
  a. determine the coverage area. When using two or more routers, the coverage area should be divided, and each router should be placed in a central location in each subdivision. If you add a wireless router to an existing network, this may mean moving the first router.
  b. decide which router is the main router. The main router is connected to the Internet, a LAN cable or other networks. It should be as close to the wired network connections or who has the best line of sight to another wireless network. In addition, the main router should be a high range router, allowing large tables of State and more users.
  c. buy a spare antenna, as the antennas that come with most routers do not have very good range. Quality omnidirectional antennas can push the range and signal strength of each of the routers, which, in turn, will reduce the cost by allowing routers less cover more space overall.
  d. deploy the primary router carefully. This router is the most important and requires most of the time of installation and options. Set the WEP (Protocol) encryption Service Set Identifier (SSID) and wireless, set up the Internet connection and test the router with some clients (computers). Once you get the main router deployed, deploy other routers should be easy.
  e. deploy the secondary routers, which must be configured to operate in "mode of transition." Secondary routers should be deployed around the perimeter of a large area or 'hot spots' where users placed - for example, will convene a bench Park or the table.

  Links:
  Create a network bridge:
  http://Windows.Microsoft.com/en-us/Windows7/create-a-network-bridge

  Add a connection to a network bridge:
  http://Windows.Microsoft.com/en-us/Windows7/add-a-connection-to-a-network-bridge

  Hope this information helps you. If you need to get help or information with decision-making wireless bridge between two different routers, I'll be happy to help you.

• "Limited connection" when you configure the network between two computers XP.

  Original title: Configuration of the network connection

  Trying to establish a network connection between two home PCs., both running Windows XP Pro. Have been through the network on both PC Setup Wizard but, they still say limited, in fact no connection. I use an Ethernet cable between the two Crusader. If it is true what I'm doing wrong?

  Thanx Terry

  Old but good, networking tips from MVP Malke, MS:

  The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

  The router configuration

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.

  2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

   

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

  Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• Help! Static route between two router WRT160NL

  Hi all

  I have my internet connection to connect to my main router from Linksys WRT160NL (192.168.1.1) with 192.168.1.x.

  My 2nd Linksys router to connect to the first gateway as well.
  The 2nd router has the ip 192.168.1.100 WAN and it's a local subnet as 192.168.2.x.

  My 192.168.2.x machines can access the internet and connect to all the machines in the network 192.168.1.x.

  However, the 1.x network cannot access the machines on the network of the 2. And because of that, I can't share or print between two networks.

  I try to add static routes on my main router (192.168.1.1) with the road: 192.168.2.0 mask 255.255.255.0 and default gateway 192.168.1.100

  However, the road does not work yet.

  in any case to ensure that the 1.x network able to access the network 2.x and 2.x access 1.x file and print sharing.

  Thanks for your help!

  Gateway of the router does NAT who made the side inaccessible side LAN WAN, unless you configure port forwarding automatic or similar. If she would not make your LAN 192.168.1 would be accessible from the internet. Static routing will not change that.

  You will need to disable NAT (aka switch to router mode) on the second router. You must configure a static route on the main router then. However, most likely your network 192.168.2 * will not have Internet more because the main router will NAT for 192.168.1. * and no 192.168.2. *.

  If possible set up the second router as access point only and run a LAN.

• What is the fastest way to transfer files between two Windows 7?

  I have two machines windows 7. I use LAN to copy files. It is only 140 Kbps. Then I use TeraCopy to the task. The speed is now 410 kbit/s. It is still too slow to copy a 80 GB of files via the LAN.

  You have any good ideas?

  I Googled that there are a lot of said articles file copy Windows 7 via the LAN is slow as it is the case, is it?

  I tried to use Windows Easy Transfer. Well, I do not see the speed, and I don't know how long it will take for the transfer file either.

  I want to see a better plan and advice.

  Hello

  Transfer of files from one computer to another depends on many factors such as the speed of the computer and the method you choose to transfer the file.

  Visit the link to learn more about the methods for file transfer between two computers:

  http://Windows.Microsoft.com/en-us/Windows7/transferring-files-and-settings-frequently-asked-questions

  Reference: http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/c30f6649-a0d9-4f5e-8671-904a8f5469bb

• How to share internet connection between two computers (win7 & win XP)?

  "I plan to get cable internet connection ADSL broadband." And again, I want to share internet from one computer to another. »
  

  • But I have a question in mind which is lower.

  Before going to answer my Question Please read two notes point-
  
  Note:

  A. very important don't ask me what I have installed and what equipment I have in my PC? just give me a simple, easy answer. guess I'm no networking and I have two PCs. You teach me from scratch.

  B. do not use the more technical term. I hate it when someone using the most incredible technical term (its towers the response in the largest number of questions lol). just give me a simple answer.

  If you are eligible to condition or except my EULA :) go further and read my questions give me an answer simple and straight.

  Now please read the question below.

  Issues related to the:

  Q1. Which computer should I connect main internet connection (computer on which will better host win7 or Win XP)?
  
  Q2. What equipment I mean as a router, hub, NIC etc.? Please specify if these materials will be required for two PCs or for one.
  
  Q3. What type of Internet connection sharing will be better to be wired or wireless (cost, speed and security wise)?

  Q4. I need two IP address both part of connection to the internet between two PCs?

  Thanks in advance.

  Hi Zeff,

  You can make Windows 7 the main computer for internet connection and then host the Windows XP computer.

  For more information, see the article:

  Start here to set up a home network in Windows 7

  Networking of computers running different versions of Windows

  With respect to the equipment as a router, hub, NIC depend on the connection (wired or wireless) you want to use. You can also check with the ISP (Internet Service Provider) for more information.

  For more information, see the articles:

  What do I need to connect to the Internet?

  Setting up a network home

  Wired and wireless connections have great benefits, but they have also some disadvantages.

  Wired connection:

  > Faster and more robust than wireless connections but not so flexible when positioning of computers and devices because you must be connected to your Super Hub with an Ethernet cable.

  > Safer than wireless connections, but not so convenient for users of laptops and other mobile devices.

  WiFi connection:

  > Wireless! If you can connect when you want. However performance may be affected by walls, electric interference etc.

  > Ideal for users of laptops and other mobile devices, you can connect devices more but slower than wired connections

  > Very safe when used with higher level (WPA) encryption. You can connect your smart phone to your network wirelessly for faster browsing.

  However, unauthorized users could try to use your connection (which explains why security is so important).

  There are two types of IP addresses. external and internal. Both computers have the same external IP address but separate internal IP addresses. Each device in your network will have its own (internal) IP address. The external IP address, who sees the Internet is actually assigned to your router.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.