Installation of HP Photosmart 6510 on Mac OS 10.9 series

Similar Questions

• Installation printer HP Photosmart Premium e-All-In-One C310 series

  I'm product HP Photosmart Premium e-All-in-One C310 series printer with code produces CN503A and model #C310a. There are 564 HP, ink cartridges. everything was going well until I installed the ink that I bought and it said I had to install the ink supplied with the product; no ink came with it and I had to buy it.  Rep me chosen good staples ink and corresponding to all the symbols. IE installation to INSTALLATION provided with the printer ink cartridges, then close the ink access door to continue.  only problem is that I did not SETUP ink. I talked to HP rep and they said selling printers don't come with ink cartridges, I bought and installation.  any other ideas?

  The first series used in the C310a cartrdiges are cartridges special "setup."  You will need to Contact HP for a replacement.  After the initial installation, the replacement cartridges you have will work.

• Photosmart 6510: PS 6510 won't print black

  Printer cannot print black ink. I ran the cycle of cleaning several times. The cartridge is new. Gets moderate use with periods where it is not used. The printer is out of warranty. Mention was made in another series of posts on this problem that there may be more specific than just running instructions once again the cleaning cycle.

  Try here.

  http://support.HP.com/us-en/product/HP-Photosmart-6510-e-all-in-one-printer-series---B2/5058334/model/5058335/document/c03760633/

  Let us know.

• Photosmart 6510 connect to the new computer with Windows 8

  I have a photosmart 6510 e - all in one printer series.  I just bought a new computer with Windows 8.  When I tried to connect my printer, an error message came up saying that I have to upgrade to Vista or Windows 7.  He does not Windows 8.  Is there a solution?

  Hello

  Download and install the latest version of the software Windows 8 below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-108880-3&cc=us&DLC=en&LC=en&OS=4131&product=5058336&sw_lang=

  Shlomi

• Photosmart 6510 does not communicate wirelessly with Mac 10.8

  I have a photosmart 6510 and an imac on 10.8

  Both worked very well together, with all functions wireless works very well, until two days ago.  Two days ago, I changed my ISP and I have a new router. My mac and printer are connected properly to the new router, but they don't communicate wireless now.

  I am able to print the wireless network test results and everything seems fine.

  But when I send anything to print I get a message saying that the printer does not communicate or can't find the printer.

  So I uninstalled and reinstalled the printer drivers and all of the HP software. Everything was fine - the installer sees the device when the usb cable is connected, it indicates that the device is connected to the correct network and upon request I have unplug the usb cable.  But then I get an error warning:

  Device not found on the network:

  Wireless network settings were downloaded successfully on your device. However, your Mac could not locate the device on the network.

  Please make sure that:

  • Your Mac is connected to a wired or wireless network that has access to your device.

  • Your device is connected to the network wireless "TALKTALK".

  Click on "Start over" to try to connect using the current settings. Click 'Go Back' to enter different settings.

  And at this time, I'm stuck.

  Can someone advise please how do I get the printer to work again wireless?

  Thank you

  I think I've solved. restore the factory settings and then reconnected and the corrected IP itself.

• HP Photosmart 2610 on MAC OS lost software installation

  The scan to printer all-in-one Photosmart 2610 function does not work.  The error message says "you must install the HP software to perform this function.  However, I can locate is no longer supplied with the printer installation CD.  I use a MAC with OS 10.7.5.   Is it possible to download the software?

  Hello @Redtail1,

  Welcome to the HP Forums!

  I understand that you are unable to scan a document using the Photosmart 2610. I will do my best to help you! Unfortunately, it is not a full software features available for this operating system. HP hereWeb site, provides an Apple Update software in order to install a basic print driver.

  Now, there are solutions that you can try to perform the scan. In this document, click "how to scan with the Apple software update driver. Try scanning from Apple Preview, Apple Image Capture or printing and scanning.

  If you have any other questions, please let me know. Have a good night!

• Network Installation unsuccessful Photosmart 6510 Windows XP

  Wireless printer: HP Photosmart 6510 B211a

  Router: Netgear WNDR3700, 802.11 g, WPA2-PSK

  Windows XP

  Photosmart 6510 series driver and SW ver 24.2.0

  When I try to install the driver, the Setup program reports "installing network without success." The installation program detects the printer, but does not end.

  The printer has network connection. It responds to ping, it works with HP ePrint, it displays Web pages on its IP 192.168.1.2. Test report wireless says that everything is OK.

  I uninstalled and reinstalled several times without success. Always the same problem "network unsuccessful installation.

  I'm looking forward to advice on how to solve the problem.

  I rebooted the router and re-installed the driver. Network installation has always fails. So I ran the Print utility and doctor Scan. Printing and scanning doctor found that the driver was not installed and advised me to download the driver from the HP site package Support & drivers.

  I downloaded and installed by using the downloaded driver package. The installation was interrupted by a Win32 exception:

  

  I installed the driver once more (without uninstalling), now with SUCCESS! My Photosmart 6510 is now running.

  Thank you!

• HP Photosmart 6510 B211a unable to Scan

  I have a HP Photosmart 6510 B211a e-Print wireless printer/scanner, that I use with my desktop version of Mac OS X Lion 10.7.5 (Mac Mini) and, with the help of Parallels Desktop 7 for Mac, I use it with my Windows 7 PC.  I am not able to scan from my HP Photosmart 6510 to my PC and not able to scan from my PC to my HP Photosmart 6510.  Moreover, I am able to scan from my Mac to my HP Photosmart 6510, but unable to scan from my Photosmart 6510 to my Mac.  I want to be able to save scans on my PC (and not only on my Mac) and be able to scan from my HP Photosmart 6510.

  Also, I am able to print from my Mac and PC.  The State of the results of the wireless network Test, "no problem found.  Congratulations on the successful your printer wireless installation. »

  "When I try to scan from the HP Photosmart 6510 as a document in the file, I get the error message"Unsuccessful Scan"and"... the States please make sure that your computer is connected to the printer and try again. "When I try to scan from my PC (from measures taken by scan - scan a document or photo), I get a long error message title 'inaccessible Scanner.  I temporarily turned off my Mac and PC firewall, but I always encountered these errors.

  Recently, I changed my phone LAN Ethernet line.  Before this change, I had no problem (at the beginning, when I bought my Mac Mini and Parallels Desktop 7 for Mac, it was very difficult to get printing and scanning to work).  Now I don't know what else I can do other than HP Photosmart 6510 to uninstall and reinstall.  Before I do, I want to know if there is anything else I can do, and if someone else had a similar situation, especially those who use Parallels Desktop 7.

  Good news!

  I was not contacted Parallels, I found another HP discussion not being able to scan.  Embarrassing, I also realized that I never properly uninstalled my printer/scanner on Windows and Mac.  Firstly, I correctly uninstalled (i.e. completely) the printer on Windows and Mac, I reinstalled the printer for Windows using the floppy disk, found the site to download the latest firmware of HP, software and tools of the diagnostic utility (http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&lc=en&dlc=en&product=5058336), reinstalled the printer for my Mac, run the tool of diagnosis utlity for printing on Windows (strange that it showed was installed my network printer but gave me an error that it) was not installed, so I clicked 'install'), and finally, I ran the scan on Windows diagnostic utility tool.

  I am now able to print and scan without problems.  Unfortunately, whenever I do a major change (upgrade of Parallels or MAC OS), I must start the process again.  At least now I have the process documented for future use.

  Thank you for your patience and your help.  I am ready to close this discussion as resolved.

• Photosmart 6510 straight cut of the page

  Hello

  I'm on a macbook with OSX 10.5.8 with a Photosmart 6510.

  Installation went without problems, but when the right side of the print documents are cut despite the margins are the same on all sides.

  Subject of PDF, it seems as it should, it is not simply print as it should - miss me the right +/-1 cm from the paper.

  PS

  Also I would like to print aligned in the Middle, which - however - perhaps a Preview of Mac problem. However, ideas are welcome...

  I already tried all these things, but I discovered as the duplex unit being a little strange ITMIS. I noticed that it cropped only the last printed page - so I just added 2 empty pages at the end and it worked.

• I have a photosmart 6510

  Wirless test - PASS results

  Installation software detects the printer on the wireless network but it will not install.

  Firewall has been disabled.

  Router Channell has been changed to 11 (tech support suggestion)

  Always the same resulting message:

  Cannot install printer on network.

  -HELP or it goes back to the store.  I need this to work...

  I found a solution!

  refer to this post...

  http://h30434.www3.HP.com/T5/Mac-printing-and-scanning/Photosmart-6510-won-t-work-wirelessly/m-p/1078971#M23503

• HP Photosmart 6510 alignment Page failure, black ink cartridge not working not

  I'm on Mac OSX using the Photosmart 6510 AIO printer 10.7.4. I had problems before printing (black ink would not introduce yourself, sensor said that there was still a lot) so I ordered new cartridges. I printed a report of quality and the color came out great but black came out uneven. Then I used the align parameter and it printed once more uneven black ink and the screen on the printer read "the alignment page failed. It's frustrating, because the printer was used only at the end of last semester and he has not worked since I set up for this semester. Any help would be greatly appreciated, thank you!

  Ryan

  The steps in this troubleshooting page can help solve the problem.  If it is printing black but spotted I expecially make sure I check the vents and run a cleaning cycle.  If the above does not resolve the issue, see the post here.

• Photosmart 6510: Photosmart 6510

  I recently bought a new laptop and I would like to install my printer Photosmart 6510, but can't find the software anywhere CD. Is someone can you please tell me where I can download the software/driver for it. Thank you

  SickNTired,

  To - Some of the Support pages have been kicking around recently.

  Here's a direct download link:

  HP 6510 V28.8 PS6510_1315-1

  Installation instructions remain the same.

  Click on the thumbs-up Kudos to say thank you!

  And... Click on accept as Solution when my answer provides a fix or a workaround!

  I am happy to provide assistance on behalf of HP. I do not work for HP.

• Print a picture on plain paper with photosmart 6510 iPhone

  Any suggestions on how to print a picture on plain paper from an iPhone or a Mac to a Photosmart 6510?

  Hello

  If you use AirPrint, the default printer for the photo for a photo paper tray. Your best option is to use the application of e-Print HP - with this application, you can select the paper size and source.

  http://WWW8.HP.com/IE/en/campaign/Photosmart/eprint.html?JumpID=reg_r1002_ieen_c-001_title_r0001

• Photosmart 6510 will not work wireless

  I just got a new 6510 Photosmart e - all in one printer which works wireless.

  I have a macbook pro, which is update 10.7.2 (I think I'm in maybe 1 or 2). anyway I'm on Lion

  I noticed when I opened my printer it had a slip that says: if I lion, do not use the installation disc that comes with it, but to use the one online, so I did.

  I had to connect my printer via the usb port on my computer because after switch on and its connection to the wifi in my house and enter my password and connect and have even tell that I am connected to the network, it wouldn't show if I tried to print from my laptop which is connected to the same wifi or my iphone 4 which is connected to my wifi.

  so after I connected with a USB and installed all the software and setting up to print wirelessly, for the instructions it tells me to unplug the usb cable (after that he told me that the printer is ready for wireless printing and it is connected and the printer is installed on the computer and everything). If I unplug the USB stick and then he says that he cannot find the printer. It is said to make sure that my printer is connected to a network connection and my computer is connected to the same connection and click on 'Retry '.  they are both connected to the same wifi at my house, and it continues to make me press 'Retry '.

  even research on my printer, on the screen, if I go into the wifi settings, it says that it is connected to the wifi in my house.

  my computer is connected to the same wifi and wifi doesn't work, because I am able to be online.

  I tried to do all troubleshooting HP provided on their website, and I have uninstalled and reinstalled the printer about 4 times. I stayed until 03:00 last night working on this and still cannot get to work.

  If someone could help me here please. I'm one step away from taking a day off, so I can call HP and tell them on the phone about it but I don't know who will be an event of the day.

  When I have the printer connected via usb it works perfectly fine. everything works. but the second I unplug, I can't find it on my computer and I can't find it on my iphone 4. my computer is connected to the wifi but my printer says that it is connected to wifi (I even unplugged the wifi printer and reconnected several times to ensure that I was connected and I am).

  Hi bradywurtz,

  If you open the preferences system - Print & Scan, the printer has a host name in brackets behind the name of the printer (for example: HP Photosmart 6510 all-in-one [G53D42])?

  If this isn't the case, then the printer in the print queue is for a USB connection, and all what you need to do is:
  1 remove the inscription of the USB
  2. click on the '+' to the bottom of the list (the white box where the printer was included)
  3. find your 6510 (connection type should be Hello)
  4. Click to select your printer, and then click Add.

  Given that you have plugged in USB and downloaded the drivers, you must have the latest drivers - but just to be sure, it would not hurt to run the software update and check and updates of HP driver Bundle (the last being 2.8).

  Please let me know if this does not solve the problem and I'll work with you more on this.

  Thank you!

• HP Scan does not work on Photosmart 6510

  HP Scan does not work with Photosmart 6510 wireless installation. I've deleted and reinstalled SW, SW, ran update doctor Scan and everything was reported OK. When I ran the scan test of the HP scan window comes but there is no value in the resolution box. When an analysis is attempted, I get ERROR SCAN only. I can scan successfully by other scanning programs.

  Paul sent me the log files, and from there, we followed the question until for the binary file HPScan.exe incorrect compatibility settings.   This file is located either in your "program files (x 86) \hp\\bin" directory (for 64-bit systems), or "program files\hp\\bin" directory for 32-bit systems.   In the case of Paul, his EXE was created to ensure compatibility for XP, which caused the application to try to use WIA 1.0 on a 2.0 WIA (Windows 7) system support.    This caused the app to not to interview the drivers for supported resolutions/etc and so the drop-down list is empty in the implementation of the resolutions.

  If other people see empty resolution lists in our application, it might be useful to double check that your EXE is not set to XP compatibility.

  Thank you

  Jeremy