Integration of TANDBERG 1700 MXP configuration with CUCM (h.323/SIP)

Similar Questions

• Tandberg 8000 mxp compatiable with sx 20?

  I use Tandberg 8000 mxp w / s/w ver 2.5, now I want to buy 1 new cisco sx 20, do I need to uggrade

  the tandberg first, or they can work without doing anything.

  You really need to upgrade this MXP as latest version is F9.3.x

  See this post for how to get a free upgrade from Cisco:

  https://supportforums.Cisco.com/message/3971210#3971210

  However, please note you can not move from 2.5 to 9 at once, see this post for the recommended upgrade path:

  https://supportforums.Cisco.com/message/3774853#3774853

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Connection of the UNIT with CUCM integration

  Hello

  Can someone please advice me on the underside, I CUCM (PUB + 1 SUB) cluster and node stand-alone 1 CUC.

  need to know the best Cisco recommended configuration

  1.0 order of AXL servers (what should we put 0 - PUB or SUB)

  2.0 tftp and order serever CUCM under port, (PUB, order SUB) group settings

  Please advice

  Thank you

  Purna

  Axl Server always be PUB and SUB.
  Pub - 0
  Sub - 1

  TFTP server must first be Sub and PUB.

  Sub - 0
  Pub - 1

  This is the best way and the recommended method to configure / integration with CUCM with connecting the unit

  Sent by Cisco Support technique iPhone App

• 320 TS Cisco with CUCM integration

  Dear experts,

  Is there a way we can integrate the TS with CUCM 320 without any conductor.

  Means of SIP trunk or as conference bridge.

  BR

  Hi Muhammad

  Telepresence on 310/320 Media Server and Cisco TelePresence Server on a Virtual Machine do not support managed locally; mode on these platforms, the telepresence server must be managed by a system as a conductor of Cisco TelePresence

  Conductor for the unique conference bridge is free.

  BR Oleksandr

• Tandberg 1700 display name

  I have a Tandberg 1700, I only have one profile and it is enabled, and my display name is stored under this profile. When I call any other VTC (not same model) the full name isn't what I put as, what Miss me? Thanks - also I don't have a manual of sorts, so I'll just out of what I found through various parts of the menu settings.

  Can you tell us how you have configured 1700, it uses CUCM/VCS for appeal, or autonomous control?  You use h.323 or SIP to connect to others, and what end points or devices you connect to?

  Usually if you use H323, the display name will be drawn from the E.164 Alias or ID H323, SIP has an option called nickname.

  For user guides and admin, and other related documents, refer to Cisco TelePresence system 1700 MXP.

  If you have any further questions on this, you move this thread to the section of telepresence of forums, where these devices are actively discussed.  To move the thread, edit and modify the categories at the bottom of the page.

• Tandberg 3000 MXP question

  Hi Experts,

  I have a client who has a Tandberg 3000 MXP, sometimes the TV screen does not start automatically when received a call. Video conference begins and unit works but the TV does not start and they can't see the other side. You need to restart the TV to make it work again. You have an idea to solve this problem?

  More information here to answer your question.

  The codec has the ability to say to display digital goto sleep or wake up through signalling between the display and the codec - if both negotiate properly.  Depends on the type of display used and configuration in the endpoint.

  But you are not limited to the use of these compatible screens... and they could use ANY type of analog or digital display.

  When the codec is not negotiating with the screen... when the display is on, off or in standby is depends on the configuration of the screen.

  Without knowing anything about the display in use... There is little we can do to help because we don't know even what is the intended outcome.

• Tandberg 1700 light green but no display

  Our Tandberg 1700 will not start.  It has a green light but no screen.  When I press a button on the remote control, the green light flashes.  I opened a hyperterminal and it seems to be looping in a large number of messages such as 0x139ffd40, pool_mss and 0x13a00340, audcamtrack_process and then starts the boot all over again.  I did the factory reset command (eee) seems to work but when I restart the system it goes back to the same loop.  Does anyone know what anyone else I could try?

  Sounds very similar to a problem in this thread: https://supportforums.cisco.com/discussion/12156181/tandberg-mxp-3000-stuck-boot-loop-and-break-keys-not-working.

  You can use the pause button to get to a CLI, then try to re - load the firmware?

  Otherwise, you must connect a call with the TAC, probably for a hardware replacement.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• MGCP FXO does not register with CUCM on VG204XM

  I have a VG204XM running MGCP with CUCM 10.5. When the port is changed and reset him CUCM config push down to the VG204XM there is an error (it is identical to the Bug CSCtr78616 reported on a router 28xx in 2011)

  In the newspapers, I see that, once the router receives the config it tried to configure AALN/S0 / / 0 (voice-port 0/0)
  However, for some reason, it seems that the router is to convert the port to a 65535 instead of 0

  "cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0".

  Since the port above does not exist on the router the survey attempt a mistake.

  Mar 27 18:07:59.278: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info:
  18:07:59.278 Mar 27: =.
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0
  18:07:59.278 Mar 27: Interface_name: AALN/S0/0
  Mar 27 18:07:59.278: controller:
  18:07:59.278 Mar 27: addr: 65535/0/0
  Mar 27 18:07:59.278: interface:
  Mar 27 18:07:59.278: voice_port: voice-port 65535/0/0
  Mar 27 18:07:59.278: dial_peer: voice dial-peer 9990655350
  Mar 27 18:07:59.278: dial_peer_port: 65535/0/0
  Mar 27 18:07:59.278:
  Mar 27 18:07:59.278: cmapp_xml_configure_router: verification of the Deleted interfaces
  Mar 27 18:07:59.278: cmapp_xml_get_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.278: cmapp_xml_configure_router: analog ports are ready
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg:
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg: old_cfg is NULL
  Mar 27 18:07:59.282: cmapp_xml_intf_cfg_changed:
  Mar 27 18:07:59.282: old intf configuration is null
  Mar 27 18:07:59.282: cmapp_xml_cfg_analog_intf:
  Mar 27 18:07:59.282: cmapp_mgcp_get_card_type_for_analog_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: intf configuration: [voice-port 65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: configuration [echo - cancel enable]
  Mar 27 18:07:59.298: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.298: cmapp_xml_cfg_router_intf: 395 line router configuration error
  Mar 27 18:07:59.298: cmapp_xml_send_msg_to_callmgr: CMBH_MSG_CFG_ERR of sending
  Mar 27 18:07:59.298: * info ERROR: the router configuration failed: voice-port 65535/0/0
  echo - cancel enable
  end

  I have a VG224 gateways running with MGCP CUCM 10,5 and no error

  Everyone knows about this problem on VG204XM?

  Hello

  Please check

  https://Tools.Cisco.com/bugsearch/bug/CSCui83022/?reffering_site=dumpcr

  Auto config MGCP fails for VG204XM
  CSCui83022
   

  Description

• 3241 GW ISDN with CUCM 10.5 or VCS

  Hi all

  What is the best practice to deploy ISDN GW 3241.

  It connects with CUCM or VCS control?

  How to connect it with CUCM or VCS?

  Kind regards

  There are some basic steps in the Quick Start Guide and there is more information on the different ways to configure it in this thread: https://supportforums.cisco.com/discussion/11580051/isdn-gw-3241-admin-config-guide

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Differences and versions of firmware Tandberg 880 MXP

  Hello

  I'm a bit confused about the differences of the Tandberg 880 MXP device firmware.

  My camera shows itself on the webGUI what follows:

  Software version:

  E5.3 PAL

  When I check the Cisco site, https://tools.cisco.com/SWIFT/LicensingUI/Quickstart#, I see for my device:

  Dispatched current SW SW
  B4.3 B4.3

  Also when I check the key to Version shipped on the page of Cisco, it does not match the Option key pressed in the webGUI on the device.

  Is any other firmware available for this device? I've heard of some issues of security vulnerability / like this:

  If you're upgrading to F8 or below, you can contact TAC and steer them to the Security Council, with it, you can get the MXP F9.3.1 software for free without needing a service contract.

  Thank you

  Maarten

  If it is running E5.3PAL, then it is likely, that this is one of the old 880 s classic and not the MXP.

  The latest version of the software E-series is E5.3 that you're already running.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Telepresence EX60 with CUCM 8.5 - How to integrate?

  Good morning people,

  I'm building a lab with 8.5 CUCM and presence Server 8.5

  I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.

  Need to install the additional server? You simply add a SIP device in CUCM?

  Can someone help me?

  Thank you

  Bruno

  Hello.

  You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.

  I recommend you take a look at this guide, after that you did with your laboratory update.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  I have attached a screenshot showing how it should look like the description of the device.

  Thank you

  Marius

• Need help - camera not connected in Tandberg 6000 MXP

  Hello

  After connection to the tandberg 6000 mxp codec HD camera, I get message camera not connected.

  There is no speicial cable to this code? and what is the axis of the s-video on the codec that mark as "'primary' cam?

  Thanks in advance

  Shy

  Camera cable aboard MXP is similar, but it does not work with 6000 MXP codecs. I assume that your cable is marked with C3000 (works only with Edsge and 3000 MXP codecs). You need the cable marked with C6000. I don't know the SKU of CISCO for this cable. It may help you reference TANDBERG:

  115420 camera HD t6000s cable, 2 m

  115421 camera HD t6000s cable, 5 m

  I hope this help you!

• Tandberg 6000 MXP restarts continuously after 1 minute

  Hi all

  I have a Tandberg 6000 MXP. Recently, it restarts continuously after only 1 minute. Anyone facing this problem?

  Please help me.

  Thank you.

  I had something similar happen to me with an EX60. It turns out that there was a problem in the registration information sip with the same information for indoor and outdoor record. Wiped factory reset the problem then reconfigure

  Sent by Cisco Support technique iPad App

• can't make an external call with CuCM and H323 gateway

  Hi experts, I have a problem with CuCM and h323 Gateway. I use a 2811 router to make a gateway H323, CuCM server and Switch layer 2 build a VoIP LAB, this my network:

  

  and my router configuration:

  Current configuration: 2335 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  router host name

  !

  boot-start-marker

  boot-end-marker

  !

  forest-meter operation of syslog messages

  !

  No aaa new-model

  !

  !

  !

  dot11 syslog

  IP source-route

  !

  !

  IP cef

  DHCP excluded-address 192.168.1.1 IP 192.168.1.10

  !

  IP VOICE dhcp pool

  network 192.168.1.0 255.255.255.0

  option 150 ip 192.168.1.2

  default router 192.168.1.1

  !

  !

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  voip phone service

  h323 connections allow h323

  allow connections h323 to SIP

  allow connections sip h323

  allow sip to sip connections

  service additional h450.12

  Fax protocol cisco

  !

  !

  !

  vocal h323 class 1

  H225 timeout tcp establish 3

  !

  !

  !

  translation of the voice-rule 1

  rule 1 / ^ 9.

  !

  !

  voice translation-profile PSTN

  translate 1 called

  !

  !

  voice-card 0

  !

  !

  application

  Service flash aa1: its - cisco.2.0.2.0.tcl

  paramspace English language en

  paramspace English index 1

  Param aa-driver 0839959204

  paramspace location English flash:

  prefix English paramspace

  !

  !

  !

  Archives

  The config log

  hidekeys

  !

  !

  interface FastEthernet0/0

  IP 192.168.1.1 255.255.255.0

  automatic duplex

  automatic speed

  H323-gateway voip interface

  port of link voip H323-gateway 192.168.1.1

  !

  interface FastEthernet0/1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  IP forward-Protocol ND

  no ip address of the http server

  no ip http secure server

  !

  !

  !

  control plan

  !

  !

  !

  voice-port 0/0/0

  cover of the echo - cancel 32

  connection ERA opx 3100

  Description 08395959204

  activation of the caller ID

  !

  voice-port 1/0/0

  !

  voice-port 0/0/2

  !

  voice-port 0/0/3

  !

  !

  !

  1010 Dial-peer voice pots

  Service aa1

  incoming called number 08395959204

  direct line to inside

  port 0/0/0

  !

  voice pots Dial-peer 2020

  PSTN description

  translation-profile outgoing PSTN

  destination-model 9 t

  Setup progress_ind allow 3

  progress_ind enable progress 8

  port 0/0/0

  Forward-digits all the

  !

  Dial-peer voice 10 voip

  destination-model 1...

  Setup progress_ind allow 3

  progress_ind enable progress 8

  h323 voice-class 1

  session target ipv4:192.168.1.2

  DTMF-relay h245 alphanumeric

  Codec g711ulaw

  No vad

  !

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  Cisco password

  opening of session

  !

  Scheduler allocate 20000 1000

  end

  I have configured the gateway h323 and attach files to router parttern on follow CUCM

  What is the problem and how to solve?

  Thanks for all the help.

  Your DP pointing CUCM is wrong, or your ÉRA OPX, depending on what you need.

  voice-port 0/0/0

  cover of the echo - cancel 32

  connection ERA opx 3100

  Description 08395959204

  activation of the caller ID

  Dial-peer voice 10 voip

  destination-model 1...

  Setup progress_ind allow 3

  progress_ind enable progress 8

  h323 voice-class 1

  session target ipv4:192.168.1.2

  DTMF-relay h245 alphanumeric

  Codec g711ulaw

  No vad

  Your DP is waiting for 1... and you send 3100, they must match.

  You might need to change the significantt numbers and entering CSS, but only you can know

  For outgoing, you are throwing 9 predot, but again, expect it in your RFP, again, change as you need.

  voice pots Dial-peer 2020

  PSTN description

  translation-profile outgoing PSTN

  destination-model 9 t

  Setup progress_ind allow 3

  progress_ind enable progress 8

  port 0/0/0

  Forward-digits all the

  You cannot transfer the numbers all send you also 9 for each call

  Change your configuration you want / need.

  HTH

  Java

  If it helps, please note

  www.Cisco.com/go/pdihelpdesk