Internet IP Ping failed

Similar Questions

• Each second ping fails

  Hi all

  I have a little test lan with the installation of 2611xm for ipsec vpn.

  On each fe port I have a laptop plugged directly inside, int is assigned by dhcp, and outside at this stage is static.

  I use 3rd party ipsec client program shrewsoft customer vpn.

  The tunnel rises and its is established with many packages of encryption and decryption.

  As mentioned in the title, each second ping fails in both directions from client to client, router 100% inside the cell phone pings and fails to address assigned 192.168.1.10 to the client ipsec "remote".

  Here is my config and below that, I think that highlights where might be the cause, the arp entry address assigned ipsec is incomplete.

  An ipconfig/all on the "remote" client shows a mac address of the int as aaaa.aaaa.aa00 tunnel.

  Kind regards

  Mitchell

  config:

  Router #show run
  Building configuration...

  Current configuration: 2139 bytes
  !
  version 12.3
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot system flash: c2600-ik9s - mz.123 - 6f.bin
  boot-end-marker
  !
  !
  no location network-clock-participate 1
  No network-clock-participate wic 0
  No aaa new-model
  IP subnet zero
  IP cef
  !
  !
  no ip domain search
  IP domain name vpn.changeme.com
  IP-server names 4.2.2.2
  DHCP excluded-address IP 192.168.0.0 192.168.0.9
  !
  internal IP dhcp pool
  network 192.168.0.0 255.255.255.0
  default router 192.168.0.1
  4.2.2.2 DNS server
  domain vpn.changeme.com
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  Keyring cryptographic remote_user
  pre-shared key address 0.0.0.0 0.0.0.0 key xxxx
  !
  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 5
  ISAKMP crypto nat keepalive 5
  crypto ISAKMP client configuration address pool local ipsec
  !
  ISAKMP crypto client configuration group remote_user_group
  key xxxx
  outdoor pool
  ISAKMP crypto profile remote_user
  Keychain remote_user
  remote_user_group group identity match
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac DYN_TFS
  !
  crypto dynamic-map DYN_MAP 1
  game of transformation-DYN_TFS
  REMOTE_USER Set isakmp-profile
  !
  !
  launch of the card client configuration address card crypto
  card crypto card client configuration address respond
  map 1-isakmp ipsec dynamic crypto map DYN_MAP discover
  !
  !
  !
  !
  interface FastEthernet0/0
  ETHERNET INTERNAL description
  the IP 192.168.0.1 255.255.255.0
  automatic duplex
  automatic speed
  !
  interface Serial0/0
  no ip address
  Shutdown
  no fair queue
  !
  interface FastEthernet0/1
  WAN ETHERNET description
  10.1.1.1 IP address 255.255.255.0
  automatic duplex
  automatic speed
  No cdp enable
  card crypto map
  !
  interface Serial0/1
  no ip address
  Shutdown
  !
  IPSec local pool 192.168.1.10 IP 192.168.1.100
  IP http server
  no ip http secure server
  IP classless
  Driving IP profile
  IP route 192.168.1.0 255.255.255.0 FastEthernet0/1
  !
  !
  access list 101 ip enable any 192.168.0.0 0.0.0.255
  !
  !
  !
  !
  !
  !
  !
  !
  Line con 0
  Synchronous recording
  line to 0
  line vty 0 4
  privilege level 15
  opening of session
  transport telnet entry
  !
  !
  !
  end

  ARP on the router #show
  Protocol of age (min) address Addr Type Interface equipment
  Internet 10.1.1.2 0 001b.d338.0bab ARPA FastEthernet0/1
  Internet 10.1.1.1 - 0017.5993.a6c1 ARPA FastEthernet0/1
  Internet 192.168.1.10 0 incomplete ARPA
  Internet 192.168.0.1 - 0017.5993.a6c0 ARPA FastEthernet0/0
  Internet 192.168.0.2 1 001b.d338.0b7c ARPA FastEthernet0/0

  The "Internet 192.168.1.10 ARPA incomplete 0 " output does not seem right. "."

  The router should not have even this particular ARP entry because there is no router with the 192.168.1.0/24 subnet interface, so there is no reason for the router to ARP for this subnet unless you connect a PC with the 192.168.1.10 ip address previously. I suggest that you turn off the router ARP entry "clear arp.

  For the following path statement: ip route 192.168.1.0 255.255.255.0 FastEthernet0/1, I would like to change the next hop of the fa0/1 to the actual ip address of the next hop router (or your ip address of PC if you connect directly a PC to the router interface fa0/1), that is to say:

  IP route 192.168.1.0 255.255.255.0 10.1.1.x

  Hope that helps.

• restoration of Internet on iMac fails

  What I need to do on my iMac, it's doing a restore of the internet back to the original operating system for the iMac. I restarted with the command-option-R keys and got into the mode of restoration of the internet. It got to the point of giving me the choice of wifi networks and I have authenticated successfully to a wifi network. Then, after a few minutes, I was presented with graphic of circle with a line through it. Looks internet restoration had failed. Am I missing something? I have to prepare my Mac somehow in order for the restoration of the Internet at work?

  Of your recovery Partition, run disk utility > first aid and tell us what he reports.

  In addition, some additional features on your Mac would be useful. What year is your Mac and what system are you running?

• Once a day, I lose all network connectivity on my Windows XP SP3 laptop. When I try to ping something I get this error: "PING failed, error 1450' code"

  Hello, those in about 3 days, I lose network connectivity on my laptop with Windows XP SP3. When I ping no matter what page of the console I get the following error message: show PING failed, error code 1450. I tried to use the option of repair in my area, but it did not help. Computer restart resolves the problem, but I'd like to avoid doing. What should I do to solve the problem?

  original title: loss of network connectivity

  Since this happen in two different ISP, try to reset your modem or router and also contact your ISP support. Some ISPS will set a rule and limitation of their user, but in your case, discuss it with your ISP, or contact technical support for your PC manufacturer.

• Successful lease IP, but ping failed and comms

  I run a network of 2 PC's at home. The two PC is running XP. I had successfully this network running with ICS for about 1 year. Due to performance issues, I decided to format the PC host. No hardware changes were made, but I load the updated drivers for all devices (including NIC - Intel Pro 100) on the formatted PC. Since the charging I can't do a ping between 2 PCs. The loop back Ping works fine on both PCs. What is really disconcerting is the fact that by using the ipconfig/all command, I see that the client PC rents successfully a new IP address of the host, but still there is no communication and ping fails. I ran several times in the Configuration Wizard from the network on both machines using different computer names (and even change the name of working group) of force to renew the connection. Whenever I see that the customer is to successfully get a new host IP lease, but always communication and ping is not available. I use AVG free edition and Windows Firewall. I also disabled the Windows Firewall on both machines, but it made no difference. I tried to put the customer on a fixed IP (192.168.0.2), but that also doesn't solve the problem. I am out, please help.

  Thanks for the reply, but the problem was resolved last night. I uninstalled the Intel driver for the NETWORK card and reinstalled an old version that I had on the disk. This instantly solved the problem, so I can assume there is a problem with the latest Intel driver. Thanks again.

• fqdn ping fails after recovery from sleep mode

  client system is win7 64 bit

  Server DSN is isc bind 9.7 works on win 7 64 bit

  local system of fqdn ping fails after recovery from sleep mode.

  I do not think that the ping never hits the network.

  Nslookup of full domain name or name of the system only exists.

  the system name ping only succeeds.

  then after ipconfig/release, ipconfig / renew, successor to ping the domain name full local system.

  someone at - it thoughts or ideas?

  Hello

  From the description of the problem, it seems that your computer is on a domain. I suggest you post the same question on the link below. The link given below is link TechNet Support for Windows 7. The question facing you is best for TechNet forums.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Feel free to write us if you have any other issues related to Windows.

• DLR ping fails

  I use 5.5 and nsx 6.1.4 esxi

  and 4 physical machines

  I have 192.168.10.0/24 and 2 sub net 192.168.0.0/24

  I use 2 physical switch each for 1 net sub but the switches are not connected

  a cluster

  OME controller

  all esxi are connected to the net with Teddy 2 sub 2

  1 VDS for the cluster

  virtual machines are simply windows.iso just to simulate network clients

  I have 4 virtual machines of windows

  VM1 and VMS 2 in esxi 3

  VM3 and vm4 in esxi 4

  VM1 and VMS 3 (10.1.0.0/24) network connected to logical switch 1

  VM2 in esxi 3 and vm in esxi 4 4 logged in LS2 (10.2.0.0/24)

  16GB in each machine

  I use windows server r2 2012 AD and DNS

  "I have congigured a DLR between LS1, LS" and transit LS

  but the ping fails between VMS in different subnet

  Anay idea?

  DNAT (Destination NAT) is required for http access to vm via a public IP address on the edge gateway ESG.

  This article on the DTA section explains the configuration steps. A Point to note is that for the feature NAT firewall must be enabled and a firewall rule for http public address must be entered.

  http://www.routetocloud.com/2014/12/NSX-v-edge-NAT/

  

• nslookup works, but ping fails by hostname (works of intellectual property). IE cannot display this webpage. Help, please!

  Cannot access Internet on my laptop with Windows XP SP2 installed; uninstalled firewall; Microsoft Security Essentials (AV) installed

  ipconfig/all shows a 192.168.x.x ip address to my ethernet card.

  TCP/IP properties are set to "Obtain an IP address automatically" and "Obtain DNS server address automatically."

  I am able to search names and ping by ip address but cannot ping by hostname. When I try to navigate through a Web site, it displays the message "Waiting for http://xxx.xxx.xxx ' in the status bar, but fails to load the Web page.

  I tried a few sites by their IP with the browser, for example 212.58.244.143, and IE was able to load the Web page (without any objects of course requiring name resolution).

  Able to ping loopback (127.0.0.1) as well as the computer by its name (which resolves to the ip address is assigned to the).

  ARP - a shows the entrance to the default gateway. Able to ping.

  I did ipconfig/flushdns and / registerdns without effect.

  Even with net stop dnscache and net start dnscache.

  Manually reset TCP/IP too by following the instructions here.

  Also used "netsh winsock reset catalog" according to the guideline here.

  Running out of ideas here... could someone please advise what to do? Or what additional information it would take to solve this problem?

  I met the same problem on win7. I also tried each solusion what you tried.

  In the end, I reinstalled the tcp/ip stack and solved this problem. Try the following steps:

  1 remove

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Winsock
  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Winsock2

  2 reset

  3. right click on the network connection and then click Properties. Reinstall the protocols of the disc. The location is 'C:\Windows\inf '. Choose the «ipv4...» "and"ipv6 ".

  4 reboot

  Everything is ok.

  Good luck!

• Internet slow (ping) on Macbook (mid-2012)

  I a mid 2012 macbook pro (non-retine) and recently started having slower speeds of the internet. When you use the Ookla speed test, my ping is generally more than 200 (sometimes as high 700); my download speed is around 3 Mbps, when it is usually around 7. I thought it was the internet connection, but then I checked with an Ipad on the same connection, internet speed was 7mbps (ping was 40). When I try the speedtest on some sites powered by Ookla (like my Qwest or at the & t support site, it won't even run the speed test, saying that there is a latency error, or there is a firewall between my computer and the server).

  What I tried that did not work:

  Turn off the firewall in my security/privacy settings.

  Removing a silverlight program I had downloaded recently play video on a local Web site, so I don't know if that would be a factor.

  Remove the DivX program, based on what I've read in another similar post on the forum.

  * I did not run an uninstall on these programs, but just moved to the trash, then maybe it is needed?

  Change my DNS openDNS numbers numbers. I've since changed my original numbers.

  Any suggestions?

  Also, I tried to plug directly into my DSL cord and without wifi. The same problem.

• DNS Broke - nslookup successful but Ping fails

  Hello

  I'm working on an old client computer that is running Windows XP SP2.

  The computer is unable to connect because of a sort of DNS issue, so it appears.

  See, very strange:

  C:\Documents and c > nslookup digg.com

  Server: quarter - pri.sys.gtei .net

  Address: 4.2.2.1

  Non-authoritative answer:

  Name: digg.com

  Address: 64.191.203.30

  C:\Documents and c > ping 64.191.203.30

  Ping 64.191.203.30 with 32 bytes of data:

  Reply from 64.191.203.30: bytes = 32 time = 83ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 81ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 82ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 86ms TTL = 242

  Ping statistics for 64.191.203.30:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 81ms, Maximum = 86ms, average = 83ms

  C:\Documents and c > ping digg.com

  Ping request could not find host digg.com. Please check the name and try again.

  C:\Documents and c >

  C:\Documents and c > nslookup digg.com

  Server: quarter - pri.sys.gtei .net

  Address: 4.2.2.1

  
  

  Non-authoritative answer:

  Name: digg.com

  Address: 64.191.203.30

  
  

  
  

  C:\Documents and c > ping 64.191.203.30

  
  

  Ping 64.191.203.30 with 32 bytes of data:

  
  

  Reply from 64.191.203.30: bytes = 32 time = 83ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 81ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 82ms TTL = 242

  Reply from 64.191.203.30: bytes = 32 time = 86ms TTL = 242

  
  

  Ping statistics for 64.191.203.30:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 81ms, Maximum = 86ms, average = 83ms

  
  

  C:\Documents and c > ping digg.com

  Ping request could not find host digg.com. Please check the name and try again.

  
  

  C:\Documents and c >

  So, as you can see the GET from the computer to the correct IP address for any domain using nslookup, but trying to ping or access any domain name instantly fails. :(

  Tried to run winsockxpfix, but that made no difference.

  Also, I tried using the service DNS, open dns but same problem.

  The computer is connected to my knowledge as work network. 7 other computers and two xbox 360 s on the network even get very well correct dns data. So it's fair to this computer.

  Even tried to install BIND 9 on the PC and the same problem. :(

  Thanks for the help,

  Will be

  God Bless America

  I fixed it by managing to install SP3. Just so install SP3 for XP fixed the problem. : D

  And Yes Ben, I tried that too. At a rating of 1. Thank you for trying to help though.

  God Bless America

• Internet Explorer 11 fails to install

  At the present time, I have Internet Explorer 9 on Windows 7 Professional x 64. I want to upgrade to Internet Explorer 11 and tried to do it through Windows updates. I made several attempts, but they always fail. The error code is 9 57.

  Hello

   
  Thanks for posting your query in Microsoft Community Forum.
   

  When you install Internet Explorer 11 for Windows 7, the installation program attempts to automatically install required components. We cannot install Internet explorer 9 11. Installing Internet Explorer 10 and upgrade to Internet Explorer 11.

  I suggest you to check if this set of prerequisite updates is already installed. To do this, you can check the following link for the game of prerequisite updates required and check out them with the updates installed on your system.

   

  Prerequisite for Internet Explorer 11 updates

  http://support.Microsoft.com/kb/2847882/en-us

   

  To check the updates installed, please see the following link:

   

  See the Windows updates are installed

  http://Windows.Microsoft.com/en-us/Windows/which-Windows-updates-installed#1TC=Windows-7

   

  After having opened the window view update history, you can check the number of KB of the prerequisite updates that are not installed and install them manually from the link previously provided.

   

  After you install the updates, restart your system. If you see no Internet Explorer 10 download Update for Internet Explorer 10 in Windows 7 (KB2859903) and install Internet Explorer 11.

  If you still have the problem, you can follow the steps in troubleshooting as provided in the following link:

   

  Troubleshooting a failed installation of Internet Explorer 11

  Warning: Security software can help protect your computer against viruses and other security threats. In most cases, you should not disable your security software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   

  Hope this information is useful. If the problem persists, please post back your results, we will be happy to help you further.

  ____________________

  Thank you best regards &,.

  Isha Soni

• Unable to install Internet dongle, error: failed to install the software & unable to connect.

  Original title: failure of the internet

  not able to connect to internet with zte mf 190 dongle Mr. the problem began when for some reason any I uninstalled the software of the electronic key. Now when I re - insert the dongle it doesn't show signs of usb. In addition, I deleted the software so I can not connect to internet unless the usb dongle is displayed. He said: software installation failed & unable to connect. Maybe there is a problem with the windows drivers. Need help.

  Hello

  I can understand the inconvenience caused to you and I appreciate your efforts to resolve the issue.

  This issue may be caused if one of the many reasons as USB driver are corrupt or unstable PC requires an update for problems that could conflict with an external USB hard disk, Windows may be missing other problems hardware or software updates.

  I would like to know;

  1. What is the brand and model of your computer?

  2. Have you checked with other USB ports?

  3. The problem occurs with other USB devices?

  I would follow the methods below and check if that helps.

  Method 1: Run the Fixit

  Tips for solving common driver problems

  If the problem persists, follow method 2.

  Method 2: Uninstall and reinstall all USB controllers.

  To remove and reinstall all USB controllers, follow these steps:

  1. Press the Start key on the keyboard.
  2. Go in Panel.
  3. Go to Device Manager.
  4. Expand Bus USB controllers.
  5. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.
  6. Restart the computer, it automatically reinstall the USB controllers .
  7. Plug in the removable USB storage device and test to make sure that the problem is solved.

  If the problem persists, follow method 3.

  Method 3:

  Follow the instructions in the given article:

  Install a USB device

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

  ____________________

  Thank you best regards &,.

  Isha Soni

• Test the IP (Ping failed)

  I want to develop an application from server to client on the Playbook.

  First thing, I'm getting is ping the Playbook of my office and vice versa.

  The Playbook seems to be able to ping from the desktop.  When I try to ping my Playbook of my desktop (Win7), it fails.

  I use the IP address found on the Playbook under Wifi settings.

  We know what I am doing wrong?  I have looked around and you haven't seen anything on this Board or Google which addresses this problem.

  Thank you.

  Thanks for responding, Mark.

  I meant with my progress so far yesterday.

  In my router settings was a checkbox for the isolation that allows anyone to see the devices on wifi.  Unchecking it now allows me to ping devices.

  I don't know what Mark refers to since I can now ping the Playbook as well as my laptop and iPod touch.

  Catch face!

• [Solved] Internet Explorer 11 fails; KB3023266 fails with code 8000FFFF

  First publication:

  Good, people

  I just I need to get a Windows Update complex Hell, involving the error "Missing winning key component ' infamous. Fixed every reg entry manually and got an own CheckSur newspaper well, it is now past.

  Finally, I put eight updates installed. Seven of then really successful. Then KB3023266 fails with 8000FFFF. However, it asked me to reboot, so I did. Upon his return, Windows Update again asked me to install KB3023266, once again, failling.

  This session, however, showed an additional problem: IE 11 were crashing. In fact, I'm not a user of IE (my main browser is Firefox), but Explorer shows gadgets (even being open sidebar.exe). I could not access panel of gadgets (she just does not open). Several other IE engine-depedant apps would break as well.
  For short: after installing updates and reboot, update process fails again and will work more properly IE 11.

  Well, I ran tool ON... Logs clean.

  Solution to the problem of IE:
  

  Explained here: https://social.technet.microsoft.com/Forums/windows/en-US/438e6f63-bfec-425e-889d-a7a1be5838c2/internet-explorer-11-and-failure-on-related-components?forum=w7itproperf

  KB3023266: I've given up trying. Maybe later.

  Suggestions?
  Thank you
  T. R. P.

  I had this problem too.  I ran Avast Antivirus software.  I removed Avast and installed very well KB3023266.

• Cannot access internet or ping external site names

  I have a problem with a cisco asa 5505

  I'm unable to access the internet from any computer on the local network. I can access the network from outside, in fact I have rdp access to a server that has been installed with it. I can also ping external IP addresses, but no names. Here is the config. For any help or suggestion is appreciated. I'm starting to believe it's a DNS issue?

  : Saved
  :
  ASA Version 8.2 (5)
  !
  My - ASA host name
  domain monsite.fr
  activate the password * encrypted
  passwd * encrypted
  names of
  name description 192.168.10.x Srv - 192.168.10.x server
  name 97.7x.xxx.xx2 outdoor-home
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.10.x 255.255.255.0 IP address
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP outside-host 255.255.255.252
  !
  passive FTP mode
  clock timezone CST - 6
  clock to summer time recurring CDT
  DNS server-group DefaultDNS
  domain monsite.fr
  object-group service rdp tcp
  Description Office remotely
  EQ port 3389 object
  inside_access_in list extended access permit tcp any any eq 3389
  inside_access_in list extended access permit tcp any any eq www
  inside_access_in list extended access permit icmp any one
  inside_access_in list extended access udp allowed any any eq ntp
  outside_access_in list extended access permit tcp any any eq 3389
  outside_access_in list extended access permit icmp any any echo response
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 192.168.10.0 255.255.255.0
  static (inside, outside) interface tcp 3389 Prov-Srv - 192.168.10.9 3389 netmask 255.255.255.255
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 97.7x.xxx.xx1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.10.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Telnet 192.168.10.0 255.255.255.0 inside
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:eea8b18bfa5f73b832857913a77486d1
  : end

  you do not allow any DNS traffic leaving your network. Add the following and try again:

   access-list inside_access_in extended permit udp any any eq 53 access-list inside_access_in extended permit tcp any any eq 53

  In general, it was not necessary to allow DNS to the entire internet, only for the DNS servers used by your internal systems.

  Some other improvements to your config:

  (1) If you configure icmp-inspection, you can remove the ACE that allows to echo-replys unconditionally in your network:

   policy-map global_policy class inspection_default inspect icmp no access-list outside_access_in extended permit icmp any any echo-reply 

  (2) the outside AS to WHAT RDP could focus a little bit more:

   access-list outside_access_in extended permit tcp any host 97.7x.xxx.xx2 eq 3389