interruption of the internet connection after installing vista sp2, only a local network

Similar Questions

• Internet connection after installing vista

  I changed the hard drive of my labtop. Then I installed a vista business on my labtop but it can not connect to the internet. I tried this way:

  Control Panel, network and internet, set up a connection or network, connect to the internet.

  But this message: 'Windows doesn't detect any network hardware. "

  Please let me know how this windows vista able to recognize my internet connection which I use through my rotor for other computers. It cannot detect my wireless also. I wasn't expecting such a problem with vista before starting the real work.

  Hello

  Using another computer / laptop go to the website of the manufacturer of your laptop > search for a driver and software download section > key in your laptop model munber > look for the Vista operating system to the correct address > find drivers for it > download and save to a Flash Drive > transfer and install them in this laptop.

  If the manufacturer of the laptop has no Vista driver available for this model of laptop, we can not help you.

  See you soon.

• Internet problems after installing vista SP2

  I'm running IE8 and yesterday I installed Vista Service Pack 2.  After the installation, I got an internet connection, but could not access all pages including my home page.  The pages would hang and the little blue circle would go round and round and nothing happened.  I also have Firefox downloaded on my computer, and still the same thing happens again.

  I checked my system tools in the lower right of the desktop and my icon for connectivity internet local and internet had a red cross on it that has not changed.  I restarted my computer several times and nothing has changed.  I used the prompt commands and ping google (my homepage) and found within seconds, so the connection was there but not able to access all pages.

  I am running Vista Home Premium as my 32-bit operating system.

  To cure the problem so far, I did system restore and completely got rid of the installation.  As soon as I did, my internet was totally fine with IE8 and Firefox.

  Any suggestions, I won't install SP2 again until I know what has caused the problem of the internet, and he was healed.

  Hi Smokeycat,
   
  Thank you for writing to Microsoft Windows Vista Answers.
   
  Since you have already restored the computer and the internet works fine, try to reinstall the stand-alone version of Service pack 2. Later, try to connect to the Internet.
   
  You have security software installed on the computer? If so, try disabling the security software and install the stand-alone version of service pack 2.
   
  Try to install the stand-alone package for Windows Vista Service pack 2, access the link below and download the file to the desktop. Later, run the installation of Service pack 2 from the office.

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=a4dd31d5-F907-4406-9012-a5c3199ea2b3&displaylang=en
   
  If the problem persists after you have installed the stand alone package, reply came back with the details:

  1. try to boot into safe mode with network after installation of Service pack 2 and try to access Internet
  2. in normal mode, try to right click on the network icon in the taskbar and click on diagnose and repair, if it gives any error make a note of it and we gives the error.
  3 - is wireless to a wired connection?
  4. do you have any router installed?
   
  I hope this helps.
   
  Kind regards
   
  Srinivas
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Interruption of the internet connection, after reset.

  When I run the diagnostic tool it says that it cannot find the default gateway.

  I'm looking for someone to help me through this

  Hello

  Please answer a few questions to refine the question.

  1. When you say "Refresh", do you mean factory restore? Why exactly did you reset?

  2. What is the brand and model of the computer?

  3. have you recently installed a new hardware before the show?

  4. which antivirus program is installed on the computer?

  Try to manually assign IP addresses as indicated by "V Badji replied on May 7, 2013" in the material provided.

  WiFi access limited, error: "the default gateway is not available.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-networking/wifi-limited-access-ErrorThe-default-gateway-is/d1d72d67-b0bb-405b-b386-52e096c45978

  Hope this information helps. Provide more information so that we can help you.

• I lost the internet connection after acceptance of your latest updates. How can I cancel the updates?

  I lost the internet connection after acceptance of your latest updates. How can I cancel the updates?

  Debbie

  How do you know that the loss of your internet connection has nothing to do with the Windows updates? You must find the reason for the loss of the connection.

  How do you connect? Is a wired or wireless with a modem or a router? If a router is the router shared with another computer and this computer can connect to the internet? You need to determine if the problem is a fault on your computer or a failure to connect to your internet access provider?

  What error messages are reported?

  Event Viewer reports

  1. normally, when an error occurs on your computer looking in Event Viewer should be your starting point to find a solution. More related system errors are recorded and get an exact copy of the relevant report is important. Unfortunately, is not easy to understand reports and most of the users computer need help with their interpretation. I have to say later interpretation.

  2 Event Viewer includes three main newspapers of Windows. Here's the Application, security, and system. For purposes of troubleshooting system is by far the most important.

  3. to access the system log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window select Windows and the system logs. Place the cursor on the system, right click and select filter current log. Check the front of the error and click OK and see you only reports errors. Click the Date and time column header to sort. You may need to click a second time to see the last report above.

  4. a tip for posting copies of error reports! Run Event Viewer and double-click the error you want to copy. Select the Details tab and check the box in front of the XML view. Click the copy button to place a copy in the Clipboard and close Event Viewer. Now start your message and paste it into the body of the message. Make sure that it is the first dough right out of the event viewer.

  5. He cautioned against three types of reports, information, and reports errors. In most situations, it is the error reports that offer the best information but sometimes WARNING reports provide useful clues.

  6. all reports have stamps date and hour and when troubleshooting, it is important to focus on the latest reports. Reports of studies from the point when the computer is started, and then check if a similar report appeared in the previous session. If errors do not repeat investigation as to why they happen is wasted effort.

  7. in the individual reports the most important information is the event ID and Source such as these help when looking for help on the internet. The description is just as important and copy the exact text to use as search criteria greatly helps achieve better results when using Google. Not paraphrase descriptions when other people asking for help.

• Laptop does not start after installing vista sp2

  My Dell XPS 1530 stopped working after installing vista sp2. He gave me instructions for installation, step 1 of 3 and it went all that they way up to step 3 of 3 and said its closure and never came back...
  Please let me know, how to start the laptop.

  Hello GoogleGuru,
  Thank you for visiting the Microsoft Answers forum.
  Because your computer does not start until the desktop computer, we were able to try the system restore to a point before you install SP2.
  Thus, with the computer is shut down. Press the power button, then press on and press F8 until you see the startup options, and then it will give you the ability to boot to the last known good configuration. (select it).

  If this does not work, you can try to boot from the Vista DVD and use the recovery console to perform a restore of the system to another point in time.

  Post back with the results.

  Thank you

  Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Vista 32 bit loses the internet connection after about 10-15 minutes.

  I lose my internet connection after 10-15 minutes.

  The message says local access only.

  The only way to reconnect is to restart the computer.

  I use a devolo home plug network system. It is connected to a 210 of BT router travel.

  I also have a new computer recently bought and installed Windows 7. There is no problem with that.

  Maybe it's a coincidence, but the problem started only since the installation of the new model.

  
  

  Hello Cody C.

  Thanks for your reply. I tried this. It is said that the drivers are up to date.

  I go into the settings of power network and checked the box "turn off network card to save energy.

  Since that seems to be OK. Only time will tell if.

  Thanks a lot for all the replies. EXTED

• Gets the error message that says non-genuine Windows, also lost the internet connection when installing Windows 10

  Original title: windows 7 Home premium product...

  I have a dell studio 1737 and was upgraded to windows 7 Home premium 32-bit. I was installing windows 10 when we lost the internet connection and now I get an error message on windows is not genuine. can someone help please!

  Use your Windows 7 Home Premium product key to activate it.

  Windows 7 is pre-installed on my computer, How can I find the product key?

  The product key is located on the COA sticker attached to the bottom of your laptop or in the battery compartment. In rare cases it can be found also in the memory compartment. For systems of the Tower, look at the top or the side of the system unit. It looks like the following:

  

  Click Start > settings > Update & security > Activation > change product key and then enter the new product key, and then click Next to activate

  If you cannot activate Windows 10 after all the above and you are sure that you have the correct edition installed, then please try phone activation:

  Activate your Windows 10 license with Microsoft Chat support

• Interruption of the Internet connection

  Original title: I lost the internet connection of mt and I want to know why? and what I can do about it?

  I lost my internet connection and I want to know why and what I can do about it?

  Hello

  1. What is the operating system installed on your computer?

  2. which web browser you are using?

  3. you get any error message?

  4. is it wired or wireless?

  5. don't you make changes to the computer before the show?

  Please provide us with more information on this issue to help you best.

  In the meantime, follow the steps in the below link.

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-i-connect-to-the-Internet

• Interruption of the internet connection. Says "network can not find proxy address.

  

   
  

  0
  I am connected directly to internet DSL.  Did a system restore and lost my internet.  When I got to the computer it connected to the internet without problem.  Now nothing I try works.  I'm so frustrated... any ideas?  It finds no network and won't let me set up a broadband access.
  Help!      I tried to undo the restoration and, of course, windows cannot do due to a missing file

  Hi TopHatter,

  ·         You try to connect to a Wired or wireless network?
  ·         Recent changes to the computer before the show took place?

  First of all, make sure that explore the Internet proxy settings are not enabled. Follow the steps for this control.

  1. launch Internet Explorer.
  2. click on Tools , then click Internet Options.
  3. click on connections tab and click LAN settings.
  4. make sure that under Proxy Server , none of these options are checked. If something is activated, please the box.

  I suggest you to see if you are able to connect to internet wired to the router.

  If your computer has problems to connect to the Internet or to other computers on a network, try to use one of the network troubleshooting utilities to solve the problem.

  Open the convenience store network by double-clicking the network icon in the tray and then clicking on solving of problems

  Open the Internet connections convenience store by clicking on the Start, then Control Panel. In the search box, type Troubleshooting, and then click Troubleshooting. Under network and Internet, click connect to the Internet.

  Follow the steps from the link below that may help you solve the problem: Open convenience stores of networking: http://windows.microsoft.com/en-US/windows7/Open-networking-troubleshooters

  using the utility in Windows 7 Network Troubleshooter: http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If you are unable to connect to your wireless network, and then follow the steps from the link below:

  How can I solve the problems of network card?: http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• error starting after installing vista sp2

  I have a dell latitude D830 running vista business 32-bit.
  Installed Windows vista sp2 update and now the computer will not boot.

  automactically goes to the Startup Repair, but still not access computers.

  Can anyone help me please with this problem?

  How can I access the hard disk to uninstall vista sp2 update.
  Would not lose information on computer...

  Any suggestions or ideas on what I can

  Thank you for using Microsoft Vista answers Forum!

  You can start your PC in safe? If you can, go ahead and uninstall the update SP2 via Control Panel > Windows Update > view update history , then select install updates. Right-click on the SP2 update and select uninstall

  How to start in safe MODE

  1. Restart your computer if it is running.
  2. Press the F8 key after your computer powers initially.
  3. Once you see the menu Advanced Startup Options , you can stop tapping.
  4. Up/down arrow keys to highlight your selection.
  5. Select Safe Mode with network and press enter.
  6. You should see loading drivers and then Please wait.
  7. You should then be on the Welcome screen.

  Connect to your computer using an account with administrator privileges.

  David O
  Microsoft Answers Support Engineer
  Visit our and tell us what you think.

• No internet connection after installing the update of security for Windows Vista

  Security updates for Windows Vista released October 13, 2009 and November 10, 2009 still an Internet connection limited Connectivity/No. Did not help uninstall updates. To do the system restore to solve the problem. Why is this?

  drusecord,
  First thing is to update your network drivers for your system.  Then see if after the update of safety, you have a problem.  If you do, I would do the following:

  Disk error checking

  System File Checker

  Then if there are updates that you already have, but are always available to consult this information:

  Troubleshooting Windows Update: offered on several occasions to update

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Samba75 USB Modem GPRS/EDGE cannot connect after installing Vista SP1

  Hi all

  I have a laptop under Windows Vista Home Premium. I can't connect to the Internet using my right to Samba75 USB GPRS/EDGE modem, once I installed Vista Service Pack 1.

  Any idea on how to solve this problem? Because of some network security options has been added by SP1 of Vista who refused to connect me with my modem?

  Kind regards.

  Hi Ken,

  Thanks for the reply.

  I found that the services required to support the diap network are some corrupted how (in other words, when you enter Services, you can start/stop/restart the service. all options is disabled). I'm not looking for is the first cause, but I think so. FYI, I already turned off all firewalls including Windows Firewall.

  I will fix this by reinstalling a new copy of Vista. Tired of the trousbleshooting.

• NB550D - no internet connection after instalation of Win 7 64 bit

  Please help - so frustrating:

  Have my NB550D upgraded Windows 7 Professional 64 bit to take advantage of 4 GB of RAM

  Now, I have no internet connection and cannot figure out what to do.

  I downloaded a driver, but says it cannot install because there is no card INTEL (R)

  Help, please!

  Thanks for the clarification!

• Satellite T130-11U, lost the Bluetooth connection after installing Mobile Broadb

  I recently bought a Satellite T130-11U and established a connection with my Nokia N82, using PC Suite.
  Then I installed my broadband Mobile (operator TMN) and lost the Bluetooth connection.

  There must be a way to overcome this 'conflict '.
  Anyone with the same problem?

  Thank you.

  Hello

  Perhaps this 3rd party application is not compatible and that is the reason why this happens
  But first, you should check if the Bluetooth is always enabled

  In addition, you should check if this issue happen after installation of the new BT stack

  Here you will find the new BT stack:
  http://APS2.toshiba-tro.de/Bluetooth/

  Welcome them