iPad is not connected to the wifi at home

Similar Questions

• iPad does not connect to the Wifi on the range 192.168.0. *.

  I have an iPad Mini (ME860BA) on os 9.3.1 that would not connect to my wifi at home.  He began to abandon their studies repeatedly a few months before and then just wouldn't connect at all.  It is on the os 9.3 so I upgraded to 9.3.1 but it did not help.  I was able to connect using a hotspot from my phone but no go on the real wifi. Sometimes it seems impossible to connect and others it seems to connect but without the wifi icon that appear (and internet access). All other devices connect to the House without exception (or question) - it's just my iPad.

  I followed every bit of advice I've found - turning wifi off & on, forgetting network, reset all the network settings, hard reboot, reboot normal, turning airplane mode turn off again, go up the brightness of the screen (odd) and finally I restored my router and the iPad to factory settings.  Nothing worked, so I took him to a store of Apple and waiting for the genius to see me I thought I would try to connect to the wifi and it went all right!  I felt a little silly to start with but they still took a look and said that he had 'something' bad, but they didn't know what.  Their best guess was that it was something to do with password authentication because they are client wifi has no password.  I returned home and disabled the security mode of the router - I have a Virgin Superhub running the 2.4 and 5 GHz primary wireless networks - no amount of adjusting the security modes (remove the password, make visible SSID, change of Protocol) makes all the difference.  However, knowing that it worked on wifi from Apple in the store, I was really puzzled.

  After ages bother with different parameters (especially in my router), I now know why it does not connect to home... My Virgin router to short on a range of address DHCP IP of 192.168. 0. * and my iPad suddenly won't connect unless the beach is 192.168. 1. * or higher.  (It connected OK for 2 years).  It took weeks to find this out, but at least now I can connect.  I turned on the wifi of comments because it uses the gamme.1.  Everything is good, connects the first time, every time!  I have not tried establishing a password (I was so happy, it connected I left because it was... well as I switch on the MAC filtering, for a little extra protection) I could try side password later and if it still connect, I'll update my post.

  My solution is very well when I'm at home but is not going to help if I get the iPad with me - it will be hit & miss if I can get the WiFi also.  Must be set correctly - I see no that it is hardware related, so there must be a bug in the software/firmware.

  Anyone having problems connecting to wifi can try the workaround network comments - at least it will get you.

  Is there a future fix for this?

  Re: iPad wifi suddenly does not save

  Change the range on the router you want to connect to.

• Troubleshooting-new HP with Windows 7 spectrum XT, does not connect to the WiFi at home?

  So I just got my brand new HP ENVY spectrum XT Ultrabook with Windows 7 Home Premium installed. 64 bit. I start it, everything works fine, except that when I connect to my WiFi at home. I tried to connect, entered my password, but it does not connect. Also tried the easy connection on the router. No luck. I checked my old laptop which runs on Windows Vista to see if WiFi worked always, and this is where it gets interesting. I was able to browse the internet and internet worked, but suddenly Windows informed me that "another computer uses the same IP address" and it stops my internet capabilities on my old laptop. I connected my cable ethernet on both computers, and it works for both computers when it is plugged. While that plugged, I discovered that I could create my own IP address, which I did on my old laptop and so far that seems to have solved the problem. However, my DESIRE is always not connecting to WiFi. Any advice?

  Hi ZachRhodes3,

  ·         You get the error message?

  Follow these methods.

  Method 1: Temporarily disable the security software .

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow step 7 the link to start the computer to a Normal startupmode.

  Method 3: Follow the steps in the article.

  Windows wireless and wired network connection problems

  5 steps: how to set up your network wireless home

  For reference:

  How can I troubleshoot network card?

  Wireless network card: frequently asked questions

• Lenovo-g50-30 does not connect to the wifi at home.

  Hello everyone, I just signed up a solution.

  I got a g50-30 lenovo with windows 8.1 about three weeks ago and I got a wireless problem since then. The laptop connects to my router (Thomson tg582n) but then it shows the limited connection alert. I can browse for about 5 minutes, but just after im unable to do, while the rest of the Smartphones and tablets can connect to it. This problem started about five weeks ago and old macbook, I had, but there does appear to be a fix. In College, I am able to connect to networks without problem wireless and Ethernet works fine as well. I tried everything, reboot and restore the router, change channels and encryption for security, created at the same IP address, I've disabled, restored and turned on windows firewall, released and renewed the IP, DNS blank. Adapter WiFi disabled and enabled, uninstalled the drivers and installed them back again. I did seriously while that I found without success, so I come to you in desperation. It would be the world if you could help. Thank you!

  Thank you VERY MUCH FOR the HELP (note the sarcasm)

  Anyway guys, I found a very good solution which put an end to my connectivity problems. Go to your wiifi configuration and properties and choose to do a custom, DNS server and then type as main Server 8.8.8.8 and 8.8.4.4 as secondary (these are the free Google DNS servers) and all your problems will disappear. If anything, do not hesitate to ask.

• My Ipad mini will not connect with my wifi at home.  Other devices are able to connect with wifi.  I repeatedly entered the wifi password, but this is not ACCEP it.  Worked very well.  I turned the mini ipad market and nothing.  Help!

  My Ipad mini will not connect with my wifi at home.  Other devices are connecting with the wifi at home.  I turned the mini ipad market a few times and nothing. He recognizes wifi but when I touch the password, it continues to request the password.  Help!  It was working fine earlier in the day.

  What has happened with your iPad since earlier today, when it worked? updated App or iOS? nothing at all

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• My iPAD asks me to update to OS 9.3, but the update fails because it says that the iPAD is not connected to the internet and when I connect to my computer iTunes it say my OS is up to date.  Help, please.

  My iPAD asks me to update to OS 9.3, but the update fails because it says that the iPAD is not connected to the internet and when I connect to my computer iTunes it say my OS is up to date.  Help, please.

  I'm surprised to hear that for an iPad 2 that the issue had apparently been set for 2 s. Please see this for more details as I know them. Maybe the servers at your site have not been updated yet for the new version of the iPad 2.  ???

  Apple released the update iOS 9.3 for older devices (air of iPad and previous iPhone, 5 s and previous) due to problems with Activation. See the following for details and possible solutions.

  http://www.IMore.com/Apple-working-iOS-93-fix-older-iPhone-iPad

  https://support.Apple.com/en-us/HT206203

  A new version for the iPad 2 is now available which does not require the activation step. A new version for other devices is not yet available.

• HP Deskjet 3055 A does not connect to the WIFI with security

  I'm trying to configure a Deskjet 3055 A on my DD - WRT router.  I am a highly qualified network engineer, so I don't know 100% what I'm doing.

  First, DD - WRT supports WPS connection, because these are very precarious.  This means that my only way to connect the pritner to my home network is to connect to my PC and use the Setup utility (downloaded from your page drivers) I use the 28.8 version.

  My router supports the 2.4 and 5 GHz and I know the printer is only 2.4 GHz.  I disabled completely the 5 GHz network in order to connect the printer, even though it shouldn't have any effect.

  I restarted my router and reset the printers wireless network using its integrated control panel.

  In any case, after a shameful 2 hours troubleshooting, I did discover that the printer WILL NOT CONNECT to the WIFI network if any security is applied against it.  It works 100% fine with open security however, it is totally unacceptable.

  I tried both WPA Personal and WPA2 Personal, both with the same effect.

  For reasons to try, I added also the printer to my network WIFI open and tried to manually change the setting WIFI via webinterface of printers, however, whenever I try and access the wireless configuration wizard, I simply get an error message saying "Internal system error" - eventually I managed to work around this another bug that has been there for years (see http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Internal-System-Error-prevents-access-t...

  After installing printers web interface WIFI, the problem is always the same and it does not connect.

  HP, we were in the order of 2500 of these printers for users of our remote site.  If you don't come to the top with a quick solution/bug fixed, consider the lost business!

  Concerning

  Ian

  After playing well, I managed to find a solution for this!

  For all users who are unable to find a solution by using the other methods, here's what to do.

  Change your local network to open the safe but note your WIFI settings for your default installation.

  Connect the printer to the open network the HP software (via USB cable)

  Go to the URL of the printer, but make sure that you connect through HTTPS - if you get an internal system error, keep refreshing until it works (WHAT A JOKE!)

  Click on 'Network', then click 'Advanced' on the left.

  Enter the network settings as they need to be secured.

  Downstairs, check "in an infrastructure network, use 802. 11b / g behavior (assuming that your assisted supports g, otherwise use the b only option), then click on apply.

  Turn on your wireless security, on your router and then the printer should connect!

  I am really confused as to why this is not automatically enabled, if the printer is not working with security on a Wireless N network wireless, then have this as the default!

  HP - feel free to thank me in this post!

• You cannot be activated because the iPad does not connect to the server

  You cannot be activated because the iPad does not connect to the server. I was told to come to the address in internet apple.com/es/support and do not see it as the solution. Can someone help me

  What is the wording accurate and complete error message?

  If she says the activation server cannot be reached/contacted

  There are 4 possible causes for this error message:

  1] activation server is actually down. Very rare and of short duration when it

  Sometimes. Solution - try again.

  [2] your firewall and/or antivirus software preventing the necessary connection. Solution-

  temporarily disable your firewall and/or antivirus software, up to the end of the activation.

  [3] computer used for activation has been used to jailbreak an iOS device in the past.

  Solution - use another computer.

  [4] iPad has been jailbroken. Your favorite search engine can provide indications but often prevent jailbreaks

  the activations/updates to succeed. By the terms of use of this forum, discussion on jailbroken iPad is

  prohibited.

• PlayBook of blackBerry Smartphones does not connect to the WiFi PRIV "hot spot"

  BlackBerry PB does not connect to the WiFi PRIV "hot spot". Implements immediately with an android tablet based - Hudl of Tesco UK - but the PB comes not to connect to the private. Reading through various bulletins and cannot find anything obvious that I missed. PB connects to the other wifi fine.

  Sorted. And so simple. Just changed PRIVATE WiFi "hot spot" to 5 GHz. thanks to Bruce using BlackBerry.

• I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  < re-titled by host >

  Take it to an Apple Store for repair or replacement.

• M177fw does not connect if the WiFi extender is activated

  Main WiFi router's CISCO E4200

  WiFi Extender is TP-LINK TL-WPA4220

  Printer is HP LaserJet MFP M177fw Pro

  Date of the firmware: 20130823

  Install Smart SW Version: 20/06/2013 1.0.13171.352

  Printer is in the same room as the CISCO router.  Extender is located in another part of the House.  Extension signal is low near the printer.  The Extender is turned off, the printer immediately connects to the WiFI network.  When the extension is enabled, the printer tries to connect several times and fails.  All computer iPhone, iPad, laptop and smart TV in room normally works with the CISCO and extension under voltage, but the HP printer does not work.  Is there something I can do to fix this?

  This has always been a problem with 2 AP make sure the router and the Extender are on different channels, like 1 & 6, 6 & 11, 1 & 11.   Where is the printer, set this AP to channel 1.  Try now.

• IPhone does not connect to the WIFI in the House when not near router

  This is a recent as problem it used to work fine.

  My iphone connects to the WIFI in my house when I'm in the same room as the router but won't connect to nowhere elsewhere in the House.

  Any other apple device I have works fine, so this would suggest that there is a problem with the phone?

  Is it possible to fix this?

  Thank you

  If your iPhone is in a case, first thing I would try is to remove the case and see if that fixes it.  Other that that, I can't imagine any easy fixes.  This article may help:

  Import photos and videos from your iPhone, iPad or iPod touch - Apple Support

  My next step would be to take it to a nearby Apple store and see if they can diagnose and help you.

• HP PavilionNotebook-15-p101nm: "windows could not connect to the"wifi"

  new tour.  installed win7/64, gatherd all the missing drivers (Device Manager was all yellow) ultimately it does not connect to the internet. What to do... ? He sees the wifi, knows his name, etc., but does not connect to it. neither cable nor wifi...

  thnks in advance

  configuration of the router... solved the problem... connected via the MAC address... ...

• Mac does not connect to the wifi and keeps crashing

  My macbook pro (end 2013) will not connect to my wifi although each device only. Now he has slow veey hone and continues on crashing, doing simple things like a PDF of scrolling. It all started a week or two after the upgrade to OSX El Capitan

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x