LASERJET P3015: ERROR CODE 49.4C02

Similar Questions

• Color LaserJet 5500: error code 59.5 k

  Hello.
  My Color LaserJet 5500 poster printer error code 59.5 k while a flashing orange light.

  What can I do to solve the problem?

  Thank you

  59.5 K refers to a motor with the toner cartridge problem black.  Several times it might just be a bad toner, that does not illuminate.  You can test.  Remove all tonics of the printer.  Turn on the printer and when it asks you to install toner, press the menu key and scroll to the diagnostics menu and then choose the item to disable control of the cartridge.  The printer will say check and he would come after a while to say ready, diagnostics mode.  If it does not try once more with the menu in the same way.  When it indicates ready diagnosis mode, open the door and install the toner cyan in black housing and the other two colors in their regular time slots and let the black toner in the printer.  Now close the door and the printer should say check and eventually come to loan, diagnostic mode.  If she comes back with the error, then you have a hardware problem with the train of drum for the black slot and will need service.  If it's ready, print a configuration page in the menu information and it should send a cyan color config page.  If so, your problem is most likely a bad black toner and it must be replaced.

• LaserJet P3015: Error of 41.20 Hp p3015

  Error 41.02.00

  I have since replaced the prTR and disposed of the defective one. Thank you

• HP Laserjet M9050 MFP: Scan error Code 30.01.16

  I have a HP Laserjet M9050 MFP Firmware: 51.051.4

  The printer was woking fine so far, but played upward...

  I get an error Scan on the screen 30.01.16 Code, have searched online and this indicates that the scanner ADF need of recalibration.

  Normally the 30.01.16 error code will remain on the screen, but if I take off the cable behind the scanner it-displayed meaning I can access the control panel and enter the menu etc.

  I tried to re - calibrate the, but it doesn't seem to work, someone has another idea about what it takes to solve this problem.

  Hahaha...

  Be sure to save the configuration when you do something.

  Well, the solutions were:

  (1) printer tour

  (2) remove trainer card and unplug the hard drive

  (3) re - connect trainer Board and open the ADF tray, printer

  4) go to Services, then calibration width ADF and calibrate as on-screen instructions.

  (5) DON'T FORGET TO SAVE THE SETTINGS.

  (6) turn on the printer and remove trainer card and reconnect the hard drive.

  (7) once who did everything turn on the printer again, and everything should work without an error.

  Note: If you get the error when the cable step 3/4 remove scanner then plug back in.

  Fixed and working again.

  This can close close...

• P3015 dn: Code error F10

  My printer will be work fine for several print, then out of the Blue work give me an F10 error code and not print. The print job does not yet show upward in the queue. Sometimes, putting off the printer and restore printing, sometimes is not. Can someone help me with what is the problem and how to fix it? Thank you.

  51 errors are some errors/scanner laser.  On your printer, it will probably mean that you need to replace the laser/scanner Assembly. On some older laserjet printers, I had success fixing this type of mistake, however, I never did on your model.  To the inside of the scanner to the laser/is an engine of chrome which sometimes becomes erased or speed slows down causing the error.  To fix, you must Access the engine and remove the part of spinning of motor, clean the real tree and putting a very small drop of synthetic oil in the Burrow, replace the part of the rotation, spin twice by hand and put everything back together.  I don't know if this is possible with your printer and on some printers once you remove the spinning part you can not get it set right so it will never work.  The part you are looking for is RM1-6322-000CN.  What is interesting, it seems this unit uses the same laser/scanner color M525 and someone is selling one on ebay for a very cheap price because he usually spends more than 100.00.

  http://www.eBay.com/ITM/HP-printer-part-RM1-6322-000CN-laser-scanner-LaserJet-500-M525-series-/161942804071?hash=item25b48b1667:g:z3gAAOSw9mFWIP - p

• HP P3015: ERROR ON THE PRINTER CAN'T USE. There 49.4C02 OF the ERROR AND DO WE ALLOW to ENTER IN THE MENU SETTINGS/AUTO

  OUR LASERJET P3015/CE527A CAME UP WITH THE ERROR 49.C02.  HE WILL NOT ENTER

  MENU/SETTINGS FOR AUTOMATIC RECOVERY.  IT COMES UP WITH THE ERROR AS SOON AS IT IS TURNED

  TURN IT BACK ON AND CANNOT ACCESS THE SETTING.

  This could be a few things-

  First thing I would do, is try to turn the machine off and then remove the network cable from the machine.  Once extracted, try to turn the machine on and see if the error goes away. If so, there are probably a print job corrupted in the queue. Which you can remove by going in Printers and devices - the print driver for the HP - go to 'see what's printing' - right click and delete the tasks in there. If the drivers are not on a server or on your computer, you may wander and find the computer on which the print job is

• ATI Mobility radeon HD 4500 series reported an error code 43 and he he had stopped working, so my printer Laserjet M1132 MFP had stoped printing.

  My computer said that ATI Mobility radeon HD 4500 series reported an error code 43 and he he had stopped working, so my printer Laserjet M1132 MFP had stoped printing. How can I make it work againg?

  SHELF MODEL: tm2-1010ea

  SERIAL NUMBER: CNU0290H5H

  Any required driver updates should come from your support site for PC manufacturers, HP? and not Ati or windows update

• LaserJet Pro CM1415fnw: Error Codes

  Can someone tell me what the error code 59.le CO means? It came after I installed a new cartride and tried other chip or snack just the cartridge was bad. I only use genuine HP products. The error code is not explained ONHP websites and the support.com says that he won't answer questions about this product. Help!

  This removes a developer motor rotation error, which is essentially the motor of the toner cartridge.

  It is possible that you have installed a cartridge that is closely related to and something got damaged.

  You can do a search online for the Service Manual of this printer and you should be able to find one, but it won't be on the HP website.

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• error code 1001 on the range of printers HP laserjet 100 color mfp175nw

  I received error codes whenever I have print something and decided to reinstall the drivers for this printer but it on the Summit craters at 99% and I get an error 1001.

  Hello Terry,

  Thanks for asking this question to Microsoft Community. I'll try and help you resolve the problem; However, I will need to ask you a few questions.

  The printer worked fine before the show? Do you have any security program installed on the computer? Have you done a recent software or changes to the material on the computer?

  Here is a link with a FIXIT who helps solve the programs which have not installed or uninstalled.

  You can also try the steps and check if it helps.

  Check and make sure that the Windows service install is running on the computer.

  (a) click Start, click Run and then type services.msc and press ENTER to open Services.

  (b) right click on the Windows Installer service and then click Properties.

  (c) if the startup type box is set to disabled, change it to manual.

  (d) click on OK to close the Properties window.

  (e) right click on the Windows Installer service and then click Start. The service should start without errors.

  (f) click on the file menu and then click on exit.

  Here is another article that contains information about the error codes.

  Hope this helps and let us know if you need more assistance. We will be happy to help you.

• error code e0

  My exhausts of hp printer 1136 showing e0 error I have replace the support, but still not recover from this.

  Welcome to the Forums of HP zubair000,
  
  By your post, I see that you have found an error code e0.
  I can help you with this problem.

  Error code e0 is for a paper jam.

  Make sure the tray is not loaded too full.

  I have provided the manual that provides the areas to check for a paper jam.

  Laserjet m1136. Start on page 206. You may need a flashlight to look into the area of toner.

  I'd do a power reset to see if that will solve the problem. When the printer is still lit, disconnect the power cable from the back of the printer. Then, disconnect the power cable from the wall outlet. Wait 10 seconds and reconnect the power cable to the wall outlet first, then the back of the printer and turn on again.
  
  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector)

  Page 189 provides the steps to clean the paper via the software path.

  Test the printer.

  If you need help, let me know.

  Good day!
  Thank you.

• Error code Win32 returned by the print processor: 2147500037. Unspecified error

  I see that this error code has been resolved.   I have a few questions on this topic tho.  Loop here, is where the fun begins.  If i see this exact problem in my hosted cloud envorioment.  The printers are installed locally and are drawn on the network when the user logs in the hosted environment. The user connecting to a full desktop, which is a Windows 2008 R2 server server.  They only receive this problem when printing via the cloud. that uses the same printer drivers installed on the local PC.  On-site printing has the success rate of 100%.

  Here are the mistakes I see:

  Https://rem.exactbid.com/ServiceRequest/SRFsmart/srprintable.as, belonged to craig_REM, document failed to print on printer HP LaserJet P2050 Series PCL6 (from CRAIG) in session 18. Try printing the document again, or restart the print spooler.

  Data type: NT EMF 1,008. Spool file size in bytes: 589824. Number of bytes printed: 540384. Total number of pages in the document: 2. number of pages printed: 0. Client computer: \\VS-XA35. Error code Win32 returned by the print processor: 2147500037. Unspecified error

  Where I am confused, is that I have no driver installed on the server.  they are all drawn in front of the user login local machine solange.  With printing works fine locally.  Uninstalling the drivers will make them any good?  or where should I be looking next?

  Hello

  Thank you for visiting the Microsoft answers community site. Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Serverforum.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• Win32 5 error code printing through Remote Desktop

  I connect to a system windows server 2008 R2 by using remote desktop.  When I try to print on my local printer (HP laserjet 1200 redirected) nothing happens.  I checked the log of events on the server and there is an entry for my attempt to print indicating that a win32 error code 5 has occurred - access denied.  Access to what?  Any ideas how I can fix this problem.

  It suggests also I restart the coil fie - no idea how I make cela or is it a Kipper!

  Hi, Bob P_852,.

  The question you have posted is related to the server and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• HP Deskjet Ink Advantage 3540th: ERROR CODE OXC4EB827FH

  During my statup printer
  error code displayed
  ERROR CODE OXC4EB827FHWLMICCI2 C

  GIVE ME QUICK ADVISOR I HAVE URGENT WORK ON PRINT
  THANKING YOU
  Yan Anand

  Hello @vikas99vickyand thank you for joining the HP Forums!

  Where do you see this error? It's on the computer, or on the screen of the printer?

  We will perform a hard reset. To do this, leave the printer and unplug the power cable for 1 minute. While it is unplugged, press and hold the power button on the printer for 10-15 seconds to release built his power, then after the minute, plug the printer in.

  Also, you have the printer connected directly to a wall outlet or is a surge protector or power bar? Even if you have used a surge protector/power bar this whole time and you feel that this is not the case, please connect to a wall outlet so that we can eliminate the source of energy as the primary cause.   Questions when it is connected to an uninterruptible power supply/Strip/surge protector power

  In this document, you will see, QUESTION: questions or problems may arise when a HP LaserJet printer is connected to a UPS (UPS), a power strip or a surge protector

  ↑ This is not limited to the Laserjet printers.

  Please reply back to let me know if it helps. If you need assistance I will thankfully come back and do my best to help!

• error code - 50

  I was trying to update my I-phone with IOS 10.02 6.  While it was updating the phone, I received an error code-50.  the phone is now stuck and I can't seem to exit the mode "update."  What does this error code mean?

  Error code - 50 on iPhone

• I keep getting an error code (-1) cannot restore iphone message what can I do?

  My iphone 5 c don't continue reading 'no service' or 'research', but it has service through Verizon, I tried to switch to airplane mode, turning turn off / turn on the phone and restore with itunes, but during the restoration it shows error message - 1 will not restore, is there anything else I can do?

  Try to restore 2 times more. If get the same error message

  take the iPhone at the Apple store nearest for a free evaluation.

  Once the diagnosis is complete, staff will explain your options.

  -1 is the hardware failure error code. Assuming that no damage to the

  your iPhone is not jailbroken, you may qualify for a reduction

  the price of the replacement warranty.

  Make a Genius Bar reservation to avoid delays.

  http://www.Apple.com/retail/Geniusbar/