LaserJet Pro m177fw loud rattling and then is blocked during initialization, will not print

Similar Questions

• HP laserjet pro 200 M276 MFP: Re: HP laserjet pro 200 M276 MFP: stuck at the screen during initialization

  Nice day

  TT arrives at 'initializing' on the touchscreen when turned on and will not complete the process. I can't print.

  I already looked in several software solutions that did not help.

  Has anyone experience this problem? Any suggestions?

  I have cold/hard reset as instruced. He has not fixed anything.

  The machine turns on, sounds like the printhead moves back, a bar at the bottom of the touch screen begins to fill from left to right (as the software does or something). It gets about 1/3 of the way across the screen then it stops, and two icons are flashing at the top right of the screen, a green circle and a triangle orange with an exclamation point in the middle of the FOITT.  The touch screen says initializing and stays there until I turn it off.

  Another difficulty that was tried was to open the toner tray and take all the cartridges of toner on, then put them all back in. that does not work either.

  What now?

  Help, please.

  Printer warranty has expired.

  I don't him did not myself but instructions in the maintenance manual look pretty simple.  Just remove the cover on the right and then the fax card, and then the trainer.  Just do a search on google for the maintenance manual.  Here is a list that I found a place that contains the component.  Keep in mind most of the time it is the trainer that is casuing the problem, but there is the possibility, it could be something else.  There is no test to be sure except first substitute the trainer.

  http://www.itpartsdepot.com/products/hp-cf224-60001-new.html?utm_source=googlepepla&utm_medium=adwords&id=56128534817&gclid=CjwKEAjwv8iwBRC35-_e8aPqwCESJAB8khP9BFv_xK-rff73tTUKurHyuVUWgUGwvko1pqvXXOiKLRoCDpPw_wcB

• HP laserjet pro 200 M276 MFP: stuck at the screen during initialization

  I liked my printer and it was working perfectly until a couple of weeks. Now he arrives at 'initializing' on the touchscreen when turned on and will not complete the process. I can't print.

  I already looked in several software solutions that did not help.

  Has anyone experience this problem? Any suggestions?

  Thanks for your reply.

  I finally find the SN, and given that my product is still under warranty, I called technical support. We did a lot of troubleshooting without success.

  They'll send a replacement.

  Thanks again for working with me.

  Lost to Houston

• Once a password is known for a site and then changed, (yahoo mail), Firefox will not be asked to remember the new password once it is changed.

  Firefox is asked to remember passwords, once recalled and changed.

  This has happened

  Each time Firefox opened

  == I changed my password in Yahoo mail

  Hello Mike.

  I've seen people with this issue before, and I have it myself. I read that reinstalling Firefox (no data is lost) solves the problem, but I think that the navigation cache clearing out too. I can't confirm this, so please tell me the results.

• Explore 9 and Windows Mail - Windows Mail emails will not print after installing Internet Explorer 9

  As soon as I installed explore 9 print not in my emails to windows messaging

  Hello

  1. what happens when you try to print e-mails through Windows mail, you receive error message?

  2. not this problem only occurs when you try to print emails from Windows mail or with applications?

  Step 1: Follow the steps in the link given below and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows?T1=tab02

  Step 2: follow the steps in the link given below.

  http://support.Microsoft.com/kb/973479

  Hope it will be useful.

• "" why do I get "Error PCL XL" and "illegal attributes" but the document will not print?

  When you try to print a PDF document that appears on the screen the result is a white sheet with a message in the upper left saying "PCL XL error" and "subsystem: IMAGE" and the error: "illegalAttributeValue", he also informed "operator: consulterles" and "Position: 16. How can I fix these messages so that I can print the document I consult?

  Hello

  Please check the following link once and see if that fixes the problem.

  PCL XL Error (Print Production)

  Also tell the OS and Acrobat version you are working on.

  Concerning

  Sukrit diallo

• I just installed the latest version of Firefox, and now the Google search engine will not work. Why?

  I just installed Firefox 30.0 and now my search engine does not work. Is there something in the new version interfere with Google search?

  You can use the SearchReset extension to reset preferences to default values.

  • https://addons.Mozilla.org/firefox/addon/SearchReset/

  Note that the SearchReset extension runs only once and then uninstalls automatically, so it will not appear on the page "> Firefox Add-ons" (topic: addons).

• HP Color LaserJet Pro M177fw: HP Color LaserJet Pro M177fw

  I have a question, my HP Color LaserJet Pro M177fw, a few days ago my printer after pulling the used toner has ceased to function and to be put off. I am attaching it once again, but at this point display information on the 'introduction' display and the printer no longer nothing prints, copies, it does not scan, still running with toner bemben, inquire about what could have happened?
  This printer is dead as a result, is it the resuscitation anyway?

  I would be grateful for any response and assistance

  Hello
  Unfortunately I'm not able to cope with the printer, checked her computer friend and is always the same problem, I've updated the printer drivers on your computer, then is the same inscription initiation, I can't even move in any way over the top toner to swap, I noticed today that the printer feel as if something is burning - burning smell.
  Unfortunately, my English is not too good to talk to a hotline telephone hp, so I wonder it is possible to communicate electronically or by the Polish translator?
  Your faithfully
  Majki891

• MFP HP LaserJet Pro 400 M425dn will not print the text to format 72 points or more

  My workplace has recently bought a M425dn of MFP HP LaserJet Pro 400 all-in-one printer. It works perfectly except for the fact that it will not print text that is 72 points or larger in size. I tried many fonts that are installed with Windows, and all them print correctly to the point size 71.5 or smaller; Another thing simply does not appear in prints. Content which is of size to 72 points or more * fact * affect the flow of the content printed on the page, however. It's like the 72 points or larger text takes up space, but it is completely invisible on the printed page.

  I tested using Microsoft Word 2002 on three separate computers, of which two have installed Windows 7 and Windows Vista installed. The problem is the same on all three computers. The printer is connected via an ethernet cable to our wired network. I have installed the printer software included, and I don't think that there are updates for it that have not been installed up to this point.

  Any thoughts on how to solve this problem?

  Hello, I just made an account to solve this problem for you guys because it has been a puzzle to me also...

  I apologize before the huge hand for the terrible grammar and punctuation that I'm in a hurry

  Now it does not work for everyone but I fixed it on my machine with the following

  now before you print it... .use (ctrl + p) in your text editor to open the print window, click (properties), and then navigate to the tab (Advanced) now, I have a section called the characteristics of the printer in this category there is an option to 'send truetype as bitmap' activate this and see if it can help someone of you, for me, with this PERMIT I can print any font size my processor will allow me to type

  in my machine's plug

  Reference Dell d6420

  Win7

  Msoft word 2007

  printer itself is

  HP laserjet 200 color m276

  printer driver is

  HP LaserJet 200 color MFP M276 PCL 6

  I understand that this printer and driver is not identical to yours in itself, but the nature of these drivers makes it highly likely that this solution works for most of you

  If this can help, someone else did post more because I'll probly do not sign in to this site I created this account just for this post and I hope to solve this annoying problem issue for many of you... .no necessary congratulations

• mouse Bluetrack 4000 light turns on normally and then turns off on problem is not the battery

  mouse Bluetrack 4000 light turns on normally and then turns off on problem is not the battery.

  Hello

  1. your wireless mouse does not work?

   
  I suggest that you follow all the steps of the article which will help you solve the problem
   

  Troubleshoot a wireless mouse that does not correctly
  http://support.Microsoft.com/kb/321122

• "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".

  Original title: when setting up Windows Media Center, I get the error message: "IR hardware not detected".

  I have an internal TV Tuner that has been installed by HP, when I bought recently a "computer build-your-own." (According to the control panel Device Manager, my tuner is a Win TV HVR 1290, made by Hauppauge). The computer came with Windows 7. While installing Windows Media Center, after setting up the TV Signal (on channel 3) I am able to see a video thumbnail on my computer screen. I am also able to change the channel using my remote control U-Verse (not the Windows remote control supplied with the computer). So far so good! I then hit next and get the following message: "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".  After you receive this message, the installation procedure is completed. I called HP that support intalled the tuner. They had not the slightest idea what to do. I then called Hauppage customer (manufacturer of TV Tuner). They said that I need to plug one end of the IR Blaster cable that shipped with the computer in a slot in the back of my computer (they told me which slot). They said so to run the IR all the way cable to my cable box and the other end of the cable to my cable box of band. They said it was necessary to be able to use my Microsoft Remote to instruct the box to change channels (cable IR stuck on the box). I told her that I did not use the Microsoft Remote, I could change the channel with my U-verse remote (that I preferred to use anyway). He said that it took the cable on the band decoder in order to remove the error message and the installation of Windows Media Center. I then called U-Verse technical adapter who informed me of their set-top boxes (made by Cisco Systems) do not have the ability to receive signals IR IR Blaster cable (or any othe IR signal source). Microsoft is apparently not understand how U-Verse set-top boxes are designed to work and sells a product incompatible remote control/IR. My question is this: How do I set up Windows Media Center, in order to avoid getting the error message "IR hardware not detected" when you install Windows Media Center and just use the remote control of the U-Verse that I prefer to use in the first place. Once understand you this point, please send the information to HP, At & T U-Verse and others. Thank you.

  Ron, I have something for you!

  and for all the people who have this problem :)

  Hi, I had the time of IR not detected in Windows 7 Ultimate with a TV wonder 650 card and a box of digital adapter from Verizon for my PC... Go on the road to installation and after the Media Center channel search, choose manual configuration. Choose the aerial signal (I aso picked after this analog) l. After he sought more, he finds no channels.  Do not be afraid. Just accept it and go to the main settings page in the Mediacenter. If I remember correctly, then select TV Guide. Choose Add channel. I added the channel 3.

  Since my Verizon box has no IR for the computer, I added the channel 3 for the media Center and I change the channels with my Verizon remote. All my stations in the Verizon box go to Channel 3.

  The story here is so, for some reason any Windows detects that only my box channel signal TV and you must manually configure the media center on the air, then go to settings and add the channel you want in the guide.

  Why the guide TV control which channel you can tune is beyond me, but the scanner locks all channels, it does not detect. they must be added manually in the guide.

  My TV works and looks okay now.

  It actually works!

  the only problem is that it is not in HD

  but there is something

  
  

• Had to uninstall CC Office and then reinstall it. I was not able to reinstall.

  I got to level desktop creative cloud but the upgrade failed and I received the error 1. I followed the steps that I founded in a guide from adobe and none of them (they were 3) managed - https://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html - so the last option mentioned was to uninstall CC Office and then reinstall it. I was not able to reinstall, I get the same error (error 1). What can I do? Moreover, I have a mac OS X Yosemite.

  uninstall all cc on your computer.

  clean through the use of the Adobe Creative Cloud cleaning tool to solve installation problems

  Restart your computer

  Reinstall the cc desktop application, https://creative.adobe.com/products/creative-cloud

• I realized that I had a message to update for a while then when I checked, I found that the app CC was missing. I downloaded and installed the application, but it will not update of software. In the creative cloud Panel, the only options I get are the Hom

  I realized that I had a message to update for a while then when I checked, I found that the app CC was missing. I downloaded and installed the application, but it will not update of software. In the creative cloud Panel, the only options I get are the Home tab to check the activity and the Stock tab. The applications tab is missing. How can I get that back so I can update photoshop and lightroom?

  Please, try the steps mentioned here https://helpx.adobe.com/creative-cloud/kb/apps-panel-reflect-creative-cloud.html

  Let me know if it works!

• printer Laserjet 1020 upgraded to windows 8.1 will not print PC HP Envy H8-1503

  Hello

  was wondering if anyone has problems printing of victory 8.1, used doctor HP printing and scanning and said everything's fine but a test page does not print as I can't print anything from another category windows 8.1. using windows 8 that I had no problem printing, I've updated all the drivers

  Also when I connect my laptop using windows 7 it prints, and with them turn off the printer laserjet 1020, then plug in the USB cable and windows 8.1 it will be printed.

  But when I turn off the 1020 laser jet, then turn it back on then try to print windows 8.1 that it will NOT print

  Thanks Mike

  Hello

  I understand that you can not print with Win 8.1.

  Drivers for win 8 and 8.1 Win are the two Version 9.
  Make sure that you uninstall the previous printer software.

  Here is a url to completely uninstall a printer in Win8.
  http://www.YouTube.com/watch?v=-M0GVVcwT-o

  Restart the computer.

  Reinstall the software of the printer again. Select full features software driver.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4131&LC=en&cc=us&DLC=en&sw_lang=&product=439320#N173

  If you need more simply make assistance let me know.

• HP Color Laserjet 2550n will not print in color?

  My HP Color Laserjet 2550n will not print in color?

  I spent half a day Googling this issue and could not find any solution?

  When I press the go and cancel the 3 test pages print fine in color set button.

  But if I try to print anything from my laptop, it's all B & W.

  I already installed the latest version of PCL5, PCL6 and PS drivers from today:

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=388401&lang=en&lang=en&cc=us&cc=us

  None of them print in color?

  I think that is the question:

  http://i.imgur.com/WM8Oy92.PNG

  But, how to fix this?

  My OS is Win 8.1Pro x 64 with all updates installed.

  The colour toners are 100%, black is at 28%.

  rk_russelking: your suggestions have been COMPLETELY & TOTALLY USELESS.

  I found the answer here:

  ... «in the printer properties, select the tab settings of the device, scroll to the very last item at the bottom, which is 'Device Type'.» The value displayed (which of course got auto-installé as a default value, for both PCL6 drivers), is "AUTO-DETECT". You would think that would work, but it apparently does not.

  In any case, by selecting the drop-down arrow, it turns out that there are three available values: AUTO-DETECT, COLOR and MONOCHROME.

  Of course she then had me select COLOR, click APPLY and then click OK. I repeated the process for the other printer PCL6. »

  

  http://i.imgur.com/dxultKG.jpg