Linksys wag325n vs wrt120n

Similar Questions

• WAG325N, DHCP, and the DSL dynamic IP address

  Hello. I have problems with the implementation of my router, a Linksys WAG325N. My internet connection is DSL. According to my ISP, I have no username or password for my account because my connection uses a DYNAMIC IP ADDRESS. The operator of my ISP tells me that for my WIFI connection all I have to do is to set it to DHCP. That's all. My ISP does not help me because they sell another brand of routers with their DSL...

  My default IP address is 192.168.1.1

  I use to access the control panel of the CIsco modem. No matter what I do, the light of the internet on the router is always Red; the power, ethernet, DSL, and wireless lights are all yellow.

  What should I do?

  Thanks in advance and MERRY CHRISTMAS to all!

  Finally fixed it!

  Here's what I did:

  Encapsulation: RFC2684 Bridged (thank you GV!)

  Multiplexing: LLC

  Called my service provider for these values:

  VPI: 0

  VIDEO RECORDER: 100

  So that anyone who is going to be having the same problem I did find this:

  My ISP is PLDT MyDSL. My linksys model is WAG325N.

  Merry Christmas to all!

  Thank you once again, GV!

• not able to connect to WAG325N Xbox 360 wireless adapter

  I have this problem. someone at - he of the bindings?

  Team support of Linksys WAG325N back and replaced by WAG160N.

  Now it works perfectly. Thank you

• Problems with LAN RJ45 Ethernet on Tecra A8 PTA83E link

  I experienced some problems with the onboard Intel PRO/1000 PL Ethernet adapter. The adapter in most cases works very well: it connects normally in 100 or 1000Mbps - full duplex - speed, depends on wich internetworking devices connected and the link has any problems.

  But, in some cases, with multiple Eth, the adapter devices involved the link at all, the Green LED on the right (link?) continually flashes with a delay of 2 seconds (0.5 "-1.5" wide) and the yellow on the left (traffic?) is always idle. On the other side of the Cat5e cable, the unit (now a Linksys WAG325N router) sign no link. There is NO cable problem.

  Windows (XP Pro, SP2) sometimes reports in the small icon of the LAN adapter on the traybar a driver connection established at different speeds (often 100 Mbit/s, but sometimes 1000Mbps!), but soon he returned to status "cable disconnected".

  I tried to upgrade the drivers directly from the pages of Support Intel because the support of Toshiba does not recognize my laptop (!), and because originally I did a downgrade to XP (I'm sorry, but I don't want to use the original MS Vista!), but nothing changes.

  The only way to establish a connection that I found is to manually reduce the speed (10 Mbps - full duplex) of XP driver advanced settings link. In this case, everything works, but a low speed.

  Can someone help me? Someone already noticed this problem?
  Thank you!
  Paolo

  Hello

  I m not very good if it isn't a cable delivers.
  Have you tried to connect the two devices using a crossover cable (cross cable)

  There are three different types of crosscable:
  -100BASE-TX-Ethernet 10BASE-T-und
  -100BASE-T4-Ethernet
  -Ethernet 1000BASE-T

  The difference is the use of pairs of crossed wires.

  However, the use of crossed cables is not necessary if you connect a router or switch device.
  But in case you want to connect two laptops, the crossover cable is required.

• HP Laserjet MFP M175nw: New router just won't recognize the printer - Laserjet MFP M175nw

  Hi all.

  It's probably a little deeper than a problem of means.

  My printer above works fine on my 2 other routers modems, even now.

  I got a new modem / router from Telstra, Technicolor TG797n v3 model.

  A number of home devices works fine with this, including computers, phones and ipads, AND EVEN an ANOTHER PRINTER HP (Laserjet CP1025nw).

  However, it simply will not recognize the MFP M175nw. I tried so many ways, restarts and redefinitions, plant a certain number of times. Tried of WPS WPS PIN code wit and EVEN directly connect to the router with a Ethernet cable. -Do anything, router simply does not see the printer.

  I even did an update of the firmware on the printer. Still not good.

  I even downloaded and run the HP print and Scan Doctor - even this program cannot find this printer.

  Any help would be greatly appreciated.

  Thank you.

  -Fauzer.

  Hi, congratulations for the suggestion. As it is a House that is put in place, the budget is a consideration.

  My linksys WAG325n is still in good condition and managed all of the printers and devices witout a problem.

  I'll try to do my gateway Tehcnicolor a pure way and the linksys router.

  I don't know exactly how to do right now, but I'll have a go, if you have any indication at the same time, please share.

  Thanks heaps.

  -Fauzer.

• Port forwarding on several computers

  Hi I just bought a Wireless Linksys WAG325N router. I usually about 2-3 machines on my network WIFI and I'd like to enable the port forwarding for each of them on a particular port. It is easy to do for a single exact machine - simply type the port number and IP of the computer to the configuration - but the problem is - I would do it for each other: example: enable the port forwarding XXXX for 192.168.1.100, 101 and 102. Help, please? Thank you in advance.

  It is the application load in a sense. You can change the assignment of external ports to resolve the correct internal port on each machine.

  Say for example using rdp that uses (port/protocol) tcp/3389 (RDP client) application actually allows you to change the external port to connect to, if you specify after the investigation period. If for example say we have rdp access to all 3 computers in the outside world. We can configure the port forwarding on every computer

  (Computers)      (internal IP addressort)            (External IP/port)

  COMP A 192.168.0.5:3389 203.x.y.z:3389

  Model B 192.168.0.10:3389 203.x.y.z:3390

  Model C 192.168.0.15:3389 203.x.y.z:3391

  It is the purpose of a router to create routing tables.

  Of course, you will need to remember which ports are assigned to which device.

  It is certainly dependent on the application. Find out if your application or service supports changing the port, ftp, rdp clients, tftp, ssh all do... Most of the 'Good' services are, as those who built it were considered in a NAT environment.

  NAT network address translation =

  Most of the things if not at the level of the applications, services even in windows are tweakable via the registry. I wouldn't say that that if you don't have experience relavent. You potentially make your workstation unusable if you're wrong.

  I hope this helps.

• VoIP provider said disable firewall SPI, which is safe?

  Hi all

  I have recently (2-3 weeks ago) changed my router to a Linksys BESFR41 wireless WRT120N-related.  I started having problems with my phone voip service - it was OK for 1 year - and after a repair with support, they suggested to disable the SPI Firewall.  They say that the SPI Firewall is known to interfere with voip.  By disabling the firewall I do my very precarious network?  If so, what other choices are there?  Should not worry about this?

  TIA

  Hello

  To cut the short story - even if I had dealing with this for two days-, it seems that my router firmware has become corrupted.  I was on a call from a technician level 4 support, and it suggested that I update the firmware and perform a full reset.  Once this done, everything seems back to normal.

  Thank you for all your help.

• Can satellite A500-17 X - I get full speed with router Linksys WRT120N WLan?

  I want to buy a "Linksys WRT120N" for my A500 - 17 X wireless router, and my question is can I get full speed with this router as 100 Mbps or more.
  I don't have as much knowledge on wireless routers and that is why I ask.

  And the other question is:
  This router will give me good signal in my apartment of 60 m 2 from one room to another?

  Hello

  I think your question should be posted in the forum of the manufacturer of the router and not here in the forum of Toshiba.

  Anyway. It seems that the Wlan WRT120N router is certified for
  IEEE 802.3, IEEE 802.3u, IEEE 802. 11 b, IEEE 802. 11 g, Wi - Fi CERTIFIED, IEEE 802.11n (draft 2.0)

  As you can see the supported WiFi standards: 802.11 B, G and N

  For your laptop s Wlan card supports Draft N, you should be able to connect to 802.11 N.

• Linksys WRT120N constantly losing connection

  I have a Linksys WRT120N wireless router that I have had for almost three years. Recently, he began to drop internet connections very randomly, sometimes several times in one hour. I lose my connection to the internet and connect locally to other laptops, then it will reconnect. It is also disconnect when wired and I have a playstation using a connection cable on the router and it loses the connection all the time as well. Does anyone have any suggestions as to what is the cause, I'm sure that it is the router and not my internet service. Thank you

  Try the following to get the improved signal strength:

  # Open the browser and in the address bar type 192.168.1.1 which will open the router configuration page.

  # Bring back the MTU (Maximum Transmission Unit) of 1500 to 1400 or less (usually located on your main configuration page / database routers)

  # Do the channel width to 20 MHz only and the channel of 6, 9, 11...

  Settings wireless #Adjust the following:

  ~ ~ Reduced from 100 to 75 beacon interval

  ~ ~ Lower the threshold of fragmentation of 2346 to 2306

  ~ ~ Lower 2347 to 2307 RTS threshold

  Now, check the status of the connectivity...

• Linksys WRT120n how to assign 811.11n

  Hi dear,

  Can you help me with my Linksys WRT120N to 811.11n, please? I put 811.11N with 40 Mhz, save and restart the device, but continues in ground 811,11 thesignal. What, s the problem?

  Thank you

  In order to get more than 54 Mbps, you must use WPA2-AES encryption and active WMM.

• Linksys wrt120n is not booting

  Hello

  I have a router linksys wrt120n for about 2 years.

  last weekend, my brother he disconnected from the power and he turned his back, but the router seems stuck on the boot sequence.

  flashes for a few seconds the power led on the Panel and then all four pcs lights will Flash for 1 second each of them (including power) and then clear again the power starts flashing and it does the same thing again and again and again.

  I tried to use the reset on the back of the router and I managed to reach the boot loader screen but after i ' v told him to download 1.0.0.5 firmeware then he hands once again, he did just the same problem and does not seem to work.

  i ' v tried to take it by default but I can't because it's just not starting...

  Please help me! I don't know what to do...

  I think that your router is working properly and can be brick.

  Follow this link to unbrick the router. See if it works.

• Unable to connect to Linksys WRT120N router using Notebook Pavilion dv1000

  Hello

  I recently bought a Linksys WRT120N router for my existing HP Pavilion dv1000 laptop. I am not able to connect to this router to my laptop.

  The steps I am following are-

  1. I activated the WLAN by clicking on the switch.

  2 a permit wireless

  3. given the available wireless networks

  4 selected my network (which is a secure (WPA) wireless network) and clicked on connect

  5 enter the network key (twice) and clicked on connect

  I get the message - "Please wait so that windows connects to the network, waiting for the network"... After a while the screen goes away; There is no message of success or failure of a current connection. The same wireless connection works my other laptop Toshiba in a jiffy, which means that my router seems to have been implemented correctly. Both are on the version of Windows XP Home Edition, SP3, 2002.

  I did the following settings for my wireless connection: -.

  the network card is PRO/Wireless 2200BG network connection

  I have the most up to date driver, checked for an update

  the network for my wireless connection authentication type is WPA - PSK

  data encryption is TKIP

  is the wireless network - enabled network (WPA) wireless security

  What follows is set for the wireless to 192.168.0.1

  manual configuration

  network-mixed mode

  name of the channel-xyz

  channel width - 20 mhz only

  great channel-auto

  STD - 6 channel - 2.437 GHZ

  SSID broadcast-enabled

  wireless security-mode-WPA Personal

  Please please help me... Please let me know if you need more information about the same... TNX!

  guys, I found others who have faced the same problem too

  the solution to this problem is the Forum of linksys... the key was to update the firmware for the router and get the wifi driver was last updated to intel!

  Here is the link for the same

  http://forums.linksysbycisco.com/Linksys/board/message?board.ID=Wireless_Routers&thread.ID=146826&view=by_date_ascending&page=4

• Configuring router user name and password for Linksys WRT120N router?

  Im trying to forward my ports for games, but I can't access my router. I put the usernam admin and leave the password empty vice versa and user name password and username password vice versa. This is a new router and this is my first time trying to access.

  Thank you

  Well, it was an old password for quite awhile ago. I didn't know that he will use an old previous routers. ??? Weird. Well, I want to change the password and the user. where should I do all here?

• Linksys WRT120N wireless router

  Hello, I just bought this router from dell.com because I thought that this would be the plu router ever. The issue is that I keep losing my internet connection in general.

  I have 2 devices wired to my PC and the other being my XBOX. I have 2 laptops, 1 Receiver USB wireless to a computer desktop and a nintendo wii console. All of my devices have been identified on the network, and at one point were all properly connected to the network and internet.

  Network security settings:

  the router user name: *.
  router password: *.
  network name (SSID): price Mauer network
  type of network security: greater security (WPA / WPA2)
  network security key: *.
  type of connection: Keep-Alive

  It's my information on my network. Of course, I have kept some information. Today alone, I had a problem with a laptop which is HP. I typed in all the correct settings and it wouldn't connect to the internet only "metered" meaning that it has been connected to the router but not the internet. Now at the SAME TIME my alienware laptop m17x WAS CONNECTED with the same EXACT settings, but it wouldn't connect.

  The only way I solved the problem was simply unplug the router and reconnect and so everyone had new Internet. Why should I have to unplug my router whenever I want to solve the problem? I shouldn't do that. I already checked to modernise the equipment of network and none are necessary. Run us a variety of platforms from windows 7, windows vista to windows xp.

  It is not my internet connection because I replaced my old modem I had for 3 years that has a Netgear router I have had absolutely no problem with. I got this modem for 2 days and I had to unplug it and plug it back at least 3 - 4 times to get the network working again. I also unfortunately after having bought this unit read the comments and unfortunately declined to read because they were all negative except for 1 or 2 of 30 or more.

  If I could solve this problem or someone has all of the recommendations that I have not tried, I'd be more than happy to try it and see if I can go at least a whole day without something happening to my network. I really don't want to go through the hassle of return this product and to set up my old router again.

  Any help would be appreciated, sorry for the frustration on my part. I want just a new router which is not 3 years old and up to date so that I can have a faster more reliable network. Not a router I have to disconnect and then re - fix issues every 30 minutes.

  Thank you

  -Matorian ([email protected])

  On your Vista and Win 7 computers turn off IPv6 under two adapters Wi-wired and LAN properties.

  In the router, turn off UPnP, under settings wireless Beacon Interval 75, RTS and Fragmentation threshold to 2304.  Save the settings.  Restart the computer and you connect again.

• FF won't connect to Linksys router

  FF 4.0.1... WRT120N Linksys router. URL to the management page 192.168.0.1.

  Connection dialog box is presented. Enter nothing (correct!). Enter the correct password. All that happens is that the dialog box flashes and reappears.

  NOTE: Connection process works very well using Chrome or IE.

  Huge problem here guys.

  Click on the Firefox button, go to Options | Options | Advanced and in the general tab, remove the check mark from "tell web sites I don't want not to be the subject of a follow-up.