M4500 to Lattitude6420

Similar Questions

• Dell precision M4500, activate or activate the fingerprint reader.

  Original title: I have a Dell precision M4500 workstation

  Hello, my question is that after that purchase the renovated new is to know how to turn on or even just turn on the fingerprint reader that is installed at the factory. I got a response that said to get with Dell, well, I called Dell and after going three steps to get someone, it says I need a code for Dell for assistance. Called Microsoft and a lady said that she would help that has been disconnected, call get 2 a man who was helping, control my motto then restarted me I thought that we will cut (Eh YES). My next call, I get a guy who said I have to pay (WHICH) and here I am back at the first stage. I'm sorry for the sounds of rattling, maybe it's not how it works, but I feel relief - HELP if you can -?

  Hello

  Thanks for posting your query to the Microsoft forum.

  I apologize for the inconvenience caused to you. I will definitely help you with this.

  The service can be activated via the Control Panel, but make sure that the drivers are install successfully and should be listed in Device Manager.

  Read this Microsoft Help article below and check the issue:

  Can I use a fingerprint with Windows reader?

  http://Windows.Microsoft.com/en-us/Windows7/can-I-use-a-fingerprint-reader-with-Windows

  Hope this information is useful. Thanks for posting for further assistance, we'll be happy to help you.

  _____________________

  Thank you best regards &,.

  Isha Soni

• Can not keep the correct time on my laptop Dell M4500

  Hi all

  I, ve problem with time on my Dell M4500 laptop a few months. I tried several solutions but not worked. time holds as long as the used laptop however wake up after sleep time shows right from the start of the commissioning (sometimes for seconds, sometimes for a few minutes) and sets then went back to a wrong value. I checked the weather it is time windows or time of bios, actually, it was the time of bios that changes after getting return of mode 'sleep' and windows after the bios later time, and if I want to correct then I have to restart, go to configuration, change time bios and then continue until the next time...

  I, ve tried the following:

  battery 1-i bios modified by a new Dell... unsolved problem
  2 - Dell has provided new motherboard with a new battery (verified) and the last update of the bios > problem unsolved
  3 went to services.msc and turned on/start/stop windows.time service > problem still there
  4 enabled auto-sync > problem unsolved

  y at - it an idea about this problem? in fact I ve called Microsoft but they replied that time BIOS cannot be changed or affected through Windows because windows does not have access to the bios time, however after change of motherboard (changed with a new one) is it a physical cause for this problem?
  any help? Thank you
  Saami

  1. click on the date and the time on the taskbar.

  2. click on change date and time settiings
  3. now check if you have set the correct time zone. If not, click on change the time zone to your local time location and click OK.
  4. now click on the internet time tab.
  5. click on change settings.
  6. then check it in as a "synchronize as internet time server.
  7. then click Update now.
  Try the following steps

• Upgrade memory M4500 gen first processor i5

  I'm trying to find out exactly what the size of the memory configuration to use my M4500 laptop to get at least 8 GB. I ordered and installed a single 8GB DIMM recommended by and bought from Dell: got an error screen saying that windows does not load. MUST I use only 2-4GB DIMM? This link in this forum seems to be saying:

  Thank you

  Al Klagge

  

  Max RAM per slot is 4G.  2 x 4 = 8 total max with a CPU dual core.

  Only with a quad core CPU (i.e., i7Q) is 8G by supported housing.

• Display of nervousness on Dell Precision M4500

  My Dell Precision began jumping and shaking quickly. She continues to do in BIOS mode.

  I'm in dual boot Ubuntu/Windows 8 if that helps

  It works when it is turned off for long periods of time (4-5 hours), but after some time starts again a jig

  Thanks for any help you can give me

  Confirmed motherboard problem

• optical drive replacing with Precision m4500 HDD Bay

  my optical drive can be replaced with a Bay of hard drive and, if so, how?

  Hi Trailrunner2,

  How about something like this?

• MSATA for HP G6 2240sh is possible?

  Hello!

  I have a HP G6 mobile 2240sh. I would like to add an ssd, but I don't want to let hdd. Can I add an msata ssd to my laptop?

  THX

  Hello

  The following list updated December 23, 2013:

  Computers laptops & tablets with slots mSATA

  Acer Aspire: R7, V5 - 572 G-6679
  Acer: Iconia Tab W500, W700
  Alienware M17x R4
  ASUS Eee Slate EP121
  ASUS PC: S400CA, S551LB,
  ASUS Zenbook: UX21, UX31
  Dell Inspiron: 14Z (5423), 15R SE, 17R, 17R 5720, 17R SE
  Dell Latitude: ST-LST01, XT3
  Dell Precision: M4500 M4600, M6400, M6500, M6600
  Dell XPS: A 2710, 18
  Dell Vostro: 3360, 3460, 3560
  Fusion Garage JOOJOO
  Gigabyte U2442
  Google: CR - 48 Chrome
  HP Pavilion: dm4t series (DM4T-3xxx)
  HP ENVY: 15 sets (15-3xxx), 17 (17-3xxx), TouchSmart 15 t-j100
  Folio of HP: 13-1000
  Lenovo: K26, K47A, K47G
  Lenovo IdeaPad: S210, S400, U300, Y460, Y470, Y480, Y500, Y510, Y560, Y570, Y580
  Lenovo IdeaPad 13 Yoga
  Lenovo ThinkPad: X 220 X 230, T420s T420, T430, T430s, T520, T530, L420, L430, L520, L530, W520, W530
  Lenovo ThinkPad Edge: E220s, E320, E330, E420, E420s, E430, E430s, E520, E530
  LG Xnote: P330
  MSI: Windpad 110W
  Samsung: Slate of series 7, Series 9
  Samsung Chromebook series 5
  Sony VAIO: Series E, type 21
  Toshiba Qosmio: X 70, X 75-A7298
  Toshiba Portege: Z830, Z835, Z930
  Toshiba Satellite: P70, P770
  WeTab

  Source: http://www.mydigitaldiscount.com/msata-ssd-compatability-list.html

  It looks like a no.

  Kind regards.

• My daughter has a laptop HP Pavilion G6 and the hinges broke-

  as she's in College, living away from home, it is difficult to see exactly what is wrong, but I have photographs, she sent me. Please could advise you on the measures to be taken that the machine is essential to his success at the University.

  I hope you can help?

  

  MrWalker.

  Discovered that the AC will work in the United States and the United Kingdom.

  Sent one with the laptop AC adapter.

  It takes just the cord with UK plug.

  The only other thing that can be a problem is there a USA keyboard. "' No English no Pound Sign."

  You can US ASCII code but it's a few key strokes.

  Or buy one and replace.

  http://www.eBay.co.UK/ITM/Dell-E5400-E5500-E6400-E6500-E6410-E6510-M4500-M2400-keyboard-RX221-UK-/111440034584?PT=UK_Computing_Laptop_Keyboards&hash=item19f257fb18

  Very easy to replace.

  Let me know what you decide on that.

  I'm going to PM the USPS tracking number.

  The last laptop that I sent to the r - u took about 10 days.

  REO

• The warning event notification: the total capacity of your system hard disk has decreased...

  Original title: the warning event Notification

  I have a Dell Precision M4500 with Intel 5 disc hard 320, Windows Vista 64-bit installed. I have enough space in C: (46.6 GB) and D: (111 GB) virtual memory C: 8192-9216. D: no, every time when I login in the laptop allways displays the following message: decreased the total capacity of the hard drive in your system. In general, this does NOT indicate a hardware failure. Communicate with your HELP
  Office if you did not personally alter the configuration of your system hard disk or disbled in System Setup.Somebody devices help me

  Hello

  ·         Will there be any changes made before this problem?

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue. Then get any drivers\software update for the device.

  Step 2: Check the hard disk for errors.

  Follow the steps in http://windows.microsoft.com/en-US/windows-vista/Check-your-hard-disk-for-errors

  Note: When you run the disk check, there is a risk of data loss you can take a backup of your files before you run the disk check.

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Entry followed FAQ

  Dell sells its laptops having the possibility to follow Jack off. This means that you do not hear an audio signal via the mic or line-in jack, even though you can hear when back you the recording and record audio.

  On many older models, a change in the Windows registry will allow a monitoring and allows you to hear the audio in real time. On laptops with a modern version of Windows, simply use the listen tab.

  There are 7 different sets of instructions below, categorized by operating system, processor and audio drivers:

  1. models with Windows XP and an Audio of Sigmatel STAC 975 x chip

  2 models with Windows XP, Audio of Sigmatel STAC 92xxHD chip and a Sigmatel driver released before the 04/12/07

  3. models with Windows XP, Audio of Sigmatel STAC 92xxHD chip and a Sigmatel R171789 driver

  4. models with Windows Vista and Sigmatel STAC Audio chip 92xxHD
  5. models with Windows XP, an IDT Audio Chip and IDT pilot R213367 (5.10.0.6159) 92HDxx
  6. models with Windows XP, an IDT Audio Chip and IDT pilot R267815 (5.10.0.6274) 92HDxx

  7. tab "Listen" on newer models

  ================================================================================

  Set of instructions 1 - for models with

  Windows XP and a chip Sigmatel Audio STAC97 & pilot

  This first set of instructions is only for these older models with the Sigmatel STAC97xx Windows XP audio chip:

  Inspiron 1100, 1150, 1200, 2200, 2600, 2650, 5100, 5150, 5160, 6000, 8500, 8600, 9100, 9200, 9300, 300 m, 500 m, 510 m, 600 m, 700 m, 710 m, XPS/XPS M170, XPS gen2 etc.

  Latitude D400, D410, D500, D505, D510, D600, D610, D800, D810 etc.

  Precision Mobile Workstations M20, M60, M70 or anyone with the Sigmatel STAC97xx and Windows XP chip.

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run. Type "regedit" without the quotes, and then click OK to open the registry.

  2. at the top of the list, select my computer.

  3. on the Edit menu, select find.

  4 type "DisableMicFromPlayback" without the quotes and click "find next."

  5. turn DisableMicFromPlayback highlighted. Right-click on it and select Edit.

  6. Select 01, then change to 00. Click OK.

  7. Optional (but 8600 users should do this) find "EnablePoPBypass", and then set the value to 00.

  8. Optional (but 600 & 6000 should do this) find "DisableMicSelect", then set the value to 00.

  9. exit the registry and restart the computer.

  Next, configure system mixer:

  1. open the Volume control by right click on the speaker icon in the taskbar, or go to start/Control Panel / sound & Audio Devices Properties / Advanced (button).

  2. under the Options menu, select Properties.

  3. under "Show the following volume controls" check Microphone. Click OK.

  4. a microphone control appears in the Volume control. Make sure that the mute box is disabled.

  5. If your external audio source (a stereo or tv tuner etc that you have connected to the mic jack) is a way to control the volume level, put down the excessive volume of entry.

  (Thanks to dilleyo of forum member who have figured this out and jk79 who later clarified and he explained to me in terms I understand.) I put in this format step by step for those of us who are not familiar with editing the registry.) It's the direct path of registry to the key:

  Computer\HKEY_LOCAL_MACHINE\System\ControlSet001\Control\Class\ \0005\Settings {4D36E96C-E325-11CE-BFC1-08002BE10318}.

  (back to top)

  ===============================================================================

  Set of instructions 2 - for models with

  Windows XP, Sigmatel STAC 92xxHD Audio Chip and driver of pre-12/07

  All of the following instructions is only for these and similar models with the Sigmatel 92xxHD audio chip running Windows XP and using a Sigmatel XP driver that was released prior to 12/04/07:

  Inspiron B120, B130/1300, 6400/E1505, E1705/9400, E1405 / 640 m, XPS M140 / 630 m, 1420, 1520, 1720

  System D420, D520, Latitude D620, D820, etc. and others with Sigmatel 92xx HD and Windows XP chip. These instructions will not work with most of the models that have been published in 2008 and after, including the Latitude 6400 and 6500 and Studio models.

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run. Type "regedit" without the quotes, and then click OK to open the registry.

  2. at the top of the list, select my computer.

  3. on the Edit menu, select find.

  4. Type "EnableInputMonitor" without the quotes, and then click "find next."

  5. turn the EnableInputMonitor highlighted. Right-click on it and select Edit.

  6. Select 00 then change to 01. Click OK.

  7. repeat "find next" (F3) several more times and keep changing the values until the "EnableInputMonitor" to come to the 01 are the correct value.

  8. find a key named "EnableIntSpkrMute" and change its value from 01 to 00.

  9. exit the registry and restart the computer.

  Next, configure system mixer:

  1. open the Volume control by right click on the speaker icon in the taskbar, or go to start/Control Panel / sound & Audio Devices Properties / Advanced (button).

  2. under the Options menu, select Properties.

  3. under "Show the following volume controls" check the input monitor. Click OK.

  4. make sure that the mute box is disabled. Unfortunately, the cursor froze in place and will not control the output volume.

  (Thanks to forum member emann15 and The Flea doing to understand this. I put in this format step by step for those of us who are not familiar with editing the registry). It's the direct path of registry to the key:

  HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ \0005\Settings\filter\Rear {4D36E96C-E325-11CE-BFC1-08002BE10318}

  (back to top)
   
  ====================================================================================

  Instruction Set 3 - for models with

  Windows XP and R171789 driver Sigmatel STAC 92xxHD Audio Chip

  04/12/07, Dell has released a driver Sigmatel XP featuring 'stereo mix', R171789 (5.10.0.5515, A11). The following models can use this driver, and in most cases have probably installed, because it is the current driver:

  Inspiron: 1501, 640 m / E1405, 9400/E1705, 1420, 1520, 1720, 1721, B120, 1300/B130, 6400/E1505
  Latitudes: XT, 120, 131, D420, D430, D520, D530, D531, D620. 630C, D631, D820, D830, D630
  Details: M65, M90 M2300, M4300 M6300
  Vostro: 1000, 1400, 1500, 1700
  XPS: M1730, M1210, M1330, M1710
  XPS/Inspiron M140 / 630 m

  It was reported that it also works on an Inspiron 1525 with a Sigmatel R180044 driver.

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run. Type "regedit" without the quotes, and then click OK to open the registry.

  2. at the top of the list, select my computer.

  3. on the Edit menu, select find.

  4. Type "EnableInputMonitor" without the quotes, and then click "find next."

  5. turn the EnableInputMonitor highlighted. Right-click on it and select Edit.

  6. Select 00 then change to 01. Click OK.

  7. repeat "find next" (F3) several more times and keep changing the values until the "EnableInputMonitor" to come to the 01 are the correct value.

  8. find a key named "EnableIntSpkrMute" and change its value from 01 to 00.

  9 find a key named "DigitalInputMonitor" and change its value to 00.

  10. find a key named "RecMonitorMute" and change its value to 00.

  11 exit the registry and restart the computer.

  Next, configure system mixer:

  1. open the Volume control by right click on the speaker icon in the taskbar, or go to start/Control Panel / sound & Audio Devices Properties / Advanced (button).

  2. under the Options menu, select Properties.

  3. under "Show the following volume controls" check the input monitor. Click OK.

  4. make sure that the mute box is disabled. Unfortunately, the cursor froze in place and will not control the output volume.

  (Thanks to the Member from the Michael_J forum who posted this edition on 11-09-08).

  (back to top)

  ==================================================================================

  Set of 4 instructions - for models with

  Windows Vista & Sigmatel STAC Audio chip 92xxHD

  This set of instructions is only for the models with the audio chip to Sigmatel 92xxHD running Vista (see above for partial list of models with chips 92xx). Not for models with Realtek or most of the IDT audio chips. These instructions are known to work with:

  Inspiron: 6400/E1505, E1705/9400 and 1525.

  (Also would work on Inspiron 1318 with 9228 Sigmatel audio chip and an IDT driver.)

  XPS: M1530

  SigmaTel Vista drivers: the instructions will work on most models that use a pre-2008 Sigmatel driver and also these new drivers:

  R171786 (6.10.0.5614, A03)

  R171788 (6.10.0.5614 A09)

  R190517 (v6.10.0.5866)

  R218148 (6.10.0.5866, A03)

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run.

  2. Type "regedit" without the quotes, and click OK to open the registry.

  3. using the + signs in the left pane, browse through the registry, in order to get to this place:

  HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ \0000\Settings\filter\SpeakerHp {4D36E96C-E325-11CE-BFC1-08002BE10318}

  [Exception: an Inspiron 1525 should navigate to... \0007\Settings\filter\SpeakerHp]

  4. click on the key SpeakerHP to select. (Some systems seem to miss this key. In this case that 'Settings'.)

  5. in the right pane, right-click and select new > binary value.

  6. Type "EnableInputMonitor" without the quotes and press ENTER.

  7. right-click the new name, and then select 'change '.

  8. in the "Value data" box, adds the 0000 existing to make 0000-01-01, and then click OK.

  9. exit the registry and restart the computer.

  10. after reboot, activate the monitor to enter the Audio properties.

  (Right click on your speaker in tray program. Click playback devices. Right click on speakers/headphones, and then click Properties. Click the levels tab. Now, you will see a box saying monitor entry. Click on the image of the speaker to reactivate it.)

  (Thanks to forum member ethan_hines, fuzzy34, Chief moore and feathead to understand this. Thanks to Bob_Ebz and dgkpcon for additional information.)
   
  (back to top)
  ======================================================================================

  Set statement 5 - for models with Windows XP AND

  IDT 92HDxx Driver R213367 (5.10.0.6159)

  These instructions are known to work with the Precision Mobile WorkStation M6400 with XP Pro SP3. They might also work with:

  Latitudes: E4200, E4300, E5400, E5500, E6400, E6400 ATG, E6500, XT2, Z600

  Dell Precision Mobile WorkStations: M2400, M4400

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run.

  2. Type "regedit" without the quotes, and click OK to open the registry.

  3. using the + signs in the left pane, browse through the registry, in order to get to this place:

  HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ \0005\Settings\filter\rear {4D36E96C-E325-11CE-BFC1-08002BE10318}

  4. find a key named "EnableIntSpkrMute" and change its value from 01 to 00.

  5. find a key named "RecMonitorMute" and change its value to 00.

  6. for each of these values, use the F3 key to search instances more of them.

  7. click on the button "back" to select.

  8. in the right pane, right-click and select new > binary value.

  9. Type "DigitalInputMonitor" without the quotes and press ENTER.

  10. right click on the new name, and then select 'change '.

  11. in the "Value data" box, 01, the value, and then click OK.

  12. exit the registry and restart the computer.

  Thank you chikinz for forum member to find this and the provision of these instructions. Chikinz also made further changes in the folder "backward" which he is unsure of importance but could be a good idea to try:

  DisableLineInFromRender changed to 00

  DisableMicInFromRender changed to 00

  EnableInputMonitor changed to 01

  For each of these values, he used F3 to search for more.

  (back to top)

  ====================================================================================
  Instruction set 6 - for models with Windows XP AND

  IDT 92HDxx Driver R267815 (5.10.0.6274, A11)

  These instructions are known to work with the Latitude E6410 with XP. They might also work with:

  Latitudes: E4200, E4300, E4310, E5400, E5410, E5500, E5510, E6400, E6400 ATG, E6400 XFR, E6410, E6410 ATG, E6500, E6510 XT2, XT2_XFR, Z600

  Dell Precision Mobile WorkStations: M4500

  [It is wise to create a system restore point before editing the registry. To create a new Restore Point go to start/Help & Support/System Restore and check "create a restore point. Even better is to save a backup copy of the registry using 'Export' usefulness.]

  1. go to the start menu and click Run.

  2. Type "regedit" without the quotes, and click OK to open the registry.

  3. using the + signs in the left pane, browse through the registry, in order to get to this place:

  HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ \0024\Settings\filter\rear {4D36E96C-E325-11CE-BFC1-08002BE10318}

  4. find a key named "EnableIntSpkrMute" and change its value from 01 to 00.

  5. click on the button "back" to select.

  6. in the right pane, right-click and select new > binary value.

  7. Type "DigitalInputMonitor" without the quotes and press ENTER.

  8. right click on the new name, and then select 'change '.

  9. in the "Value data" box, 01, the value, and then click OK.

  10. exit the registry and restart the computer.

  Forum member szabozo figured this out and shared these instructions.
  Note: szabozo tried with the new driver IDT R267823 (5.10.0.6281, A12), but it doesn't work with this driver.

  (back to top)

  ===========================================================================

  Instruction Set 7 - Use the "Listen" tab in Windows 7 and 8

  Modern Windows operating systems have an integrated monitoring device and may not have the registry changes that are described above.

  Locate the audio (speaker) icon next to the clock in the taskbar.

  

  Right-click on the icon and then left-click on "recording devices".

  

  The recording of the sound Properties tab opens. Select your device in the list and then click "Properties".

  

  The next screen has several tabs at the top. Click the "Listen" tab put a check mark next to 'Listen to this device.

  Being of other settings you want and click 'Apply', then 'OK '.

  

  (back to top)
  ===================================================================
  ===================================================================

  Published 11/27/2007

  Published on 19/01/2009

  Published on 07/02/2009

  Published on 07/08/2009

  Published on 16/02/2010

  Published on 19/07/2010

  Published on 15/08/2010

  Published on 17/03/2014

  Please do not answer in this thread that is a FAQ.

  I haveyou have comments or questions, please start a new thread and f.

  Thanks, I appreciate it.

• DELL 1510 N WLAN Mini card is compatible with the W8?

  I installed W8 on my Dell Studio 1735. Access wireless Internet is very very slow. I don't have this problem with W7 on the same computer. I tried with an external network cable. Very fast, 50mbps. I also tried with an external wifi adapter USB Belkin. It works very well. Computer is a Dell Wireless 1500 N WLAN Mini Card Driver version: 5.100.245.20 Date: 2012-03-13. I can't find a better driver.

  I have another problem I do have with W7.  I can't evaluate the computer. The Windows experience index cannot go beyond test Direct3D 10 Texture Load assessment.

  Can anyone help?

  Thank you.

  I seemed to have found a solution to my issue.
  

  I was able to find a Win 7 driver that solves my Windows 8 driver issue with very slow and intermittent/dropped
  

  wifi connections for the Dell 1510 N WLAN (Broadcom 4322) wifi adapter.
  

  The driver I found is: Network_Driver_WD35F_WN_5.100.235.12_A37
  

  I found it here: http://www.dell.com/support/drivers/us/en/04/driverdetails/product/precision-m4500?driverid=wd35f&fileid=2962647016
  

  The the auto installer will not run without error. However, it will allow you to extract the files from the driver
  

  package to a directory of your choice.  Then you can point Windows 8 driver change/update utility
  

  ('Have Disk') to that directory - 'Drivers/Win7/WL' and select the bcmwl6.inf to install a driver
  

  (Broadcom v.5.100.235.12)
  

  I hope this helps others.
  

• On Windows 7 Ultimate sound problem

  Hello

  I use Creative 4.1 sound system on my PC for some time. But, recently, I reinstalled Win 7 32 bit on my PC again and now only work 4 speakers.

  I tried to install the latest drivers from Realtek HD sound card, but still works as a single. Moreover, when I test the sound through the configuration, etc., all four speakers to emit sounds, but when I start to play a game, or turn on a song, only one works

  To check that all the speakers have any hardware problem, I seconded the speaker wire that runs and tied the other three sons one after one, and they were clearly working since the a slot.

  Before work on the left and three other right and rear left does not.

  So, I made things quite a bit in do.like can define his Quad, even I tried to use 5.1 sound, however changing Control Panel, but each of them has proved to be futile attempts...

  Some people say, you can buy a sound card, but my friend has the same set of things and its four speakers all work if he did not have a sound card.

  In short, all stakeholders work of the aspect material, but the work when I test sound, not not when playing songs etc.

  Kindly give me solution to this problem...

  Thank you.

  See here for some clues...

  http://webtrickz.com/how-to-connect-creative-inspire-M4500-4-1-speakers/

• Problem with VPN connection via a wireless card broadband Verizon Cisco VPN air

  I can't access any device on my network via RDP or applications via the host file - forwarded servers from my 64 bit Windows 7 laptop using wireless broadband Verizon and customer VPN Cisco 64 bit 5.0.7.290. I can connect easily via a LAN wired connection from home using the same laptop computer and client VPN and RDP.

  The VPN client connects to the server VPN (easy VPN on Cisco 2821 router) on the broadband wireless connection (I can see it in the GPMC on the router) but it will pass no data. I can't ping anything in the field, or external IP address. When I try to ping the laptop, it drops off the VPN (completed peer connection).

  The laptop is a Dell M4500 running Windows 7 Ultimate 64 bit OS. The VPN client is stated, rev 5.0.7.290. The card internal wireless broadband is a QualCom 5620 (EV-DO-HSPA) system (Gobi 2).

  What must I do to get this configuration to perform and log as does the wired connection?

  Tim Carlisle

  The Systems Manager

  Post edited by: Timothy Carlisle recently I discovered that the Cisco 64 bit client VPN running on my Dell Precision M6500 (Windows 7 64-bit OS) was able to connect properly using the WiFi on my iPhone 4S (Verizon Wireless). It will also connect when attached to the laptop via a USB cable. Once I discovered this, I was then able to do the same thing on the laptop that spawned this discussion, by attachment for Blackberry "BOLD" from the boss after the download and installation of a new Verizon Wireless Access Manager utility that has allowed to select the device (Blackberry) for installation.  I think that enabled us to bypass the wireless cards Gobi2 on two laptops and the factory installed Dell Connection Manager software which was not compatible with the Cisco VPN 64 bit client software. As much as I fear here, this new method (hotspot of Smartphone and attachment) is the way to go for us and has solved all the problems of connectivity distance for us. Thank you to all who have contributed to this discussion.   Tim Carlisle

  The Solution to the debate has been captured in this Document: -.

  https://supportforums.Cisco.com/docs/doc-18721

  We fought with the same question for quite awhile before finding that there seems to be a default setting in the Verizon Access Manager software that plays well with the Cisco Client.

  In VZAccess Manager, select Options | Preferences.  Connectivity options, the default setting for "NDIS Mode - connect manually" was chosen.  Change this option to "Modem Mode - connect manually" seems to have completely addressed the issue.  We can now connect to the WWAN, establish a Cisco VPN session and have connectivity.

  

• BSOD need assistance, I write the DMP file

  Hello, I have random BSOD during one day, like 4 times a day, I have seen fltmgr.sys as a problem, but I'm not sure. I write the dmp file, someone please help to undestand the problem please...

  dump file: http://www.4shared.com/file/xJejn93kba/060714-46597-01.html

  Info sys drivers: http://www.4shared.com/document/189XKlIWce/WER-581946-0sysdata.html

  Signature:
  Problem event name: BlueScreen
  Versão sistema operational: 6.1.7601.2.1.0.256.1
  Identificacao da Localidade: 1046

  Ilha de sober information o problema:
  BCCode: 50
  BCP1: FFFFFA800FAB4000
  BCP2: 0000000000000000
  BCP3: FFFFF88002692300
  BCP4: 0000000000000000
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1

  MSInfo: Nome operational system Microsoft Windows 7 Ultimate
  Versão 6.1.7601 Service Pack 1 build 7601
  Other information sober o Sistema operational issues available
  Faffa Sistema operational Microsoft Corporation
  Nome sistema LORENZOFP-PC
  Faffa sistema Dell Inc.
  Modelo sistema Precision M4500
  Tipo sistema PC x 64
  PROCESSADOR Intel (r) Core i7 CPU Q 740 1.73 GHz, 1734 Mhz, 4 Nucleo (s), 8 Processador (es) Lógico (s)
  Data/versão do A15 BIOS Dell Inc., 12/05/2013
  Versão SMBIOS 2.6
  Pasta do Windows C:\Windows
  Pasta sistema C:\Windows\system32
  Device inicializacao \Device\HarddiskVolume2
  Localidade Brasile
  Camada de Abstracao of material versão = "6.1.7601.17514."
  Name of user lorenzofp-PC\lorenzofp
  Fuso Monday Hora oficial do Brasil
  Memoria física (RAM) 8.00 GB installed
  Memoria total fisica 7.99 GB
  Memoria fisica 4.14 GB available
  Memoria virtual total 16.0 GB
  Memoria virtual available 11.8 GB
  Espaço land paginacao 7.99 GB
  Land of paginacao C:\pagefile.sys

  Thank you very much.

  Very interesting journal. It seems that the pilot who seemed to be a rootkit is a false positive with a strange string. Or a rootkit is present, but we cannot detect. avastMBR crashing may be related to something else in all cases, however.

  First of all, can you please uninstall Daemon Tools Lite + alcohol?

  In addition, subsequently, c:\windows\system32\drivers\sptd.sys is listed and loaded into your list of modules; SCSI pass through Direct Host - Daemon Tools (BSOD known issues with Win 7 and 8). Please remove it as soon as POSSIBLE with the uninstall tool - http://www.duplexsecure.com/en/downloads

  Kind regards

  Patrick

• Iomega usb 2.0 EGO unrecognized

  When I plug my new 320 E concert - GB external hard drive on Dell M4500 laptop under Windows 7 Pro 32-bit device is not recognized.

  : "USB device not recognized".

  System Tools, material resources and foung no conflicts.

  When we look at system tools, system information, reports on hardware issues:

  Device unknown USB\VID_0000 & PID_0000\6 & 3189BB0F & 0 & 43 3
  This external hard drive work on my Windows XP laptop.

  If you have any suggestions on how to solve this answer please, thanks Chuck

  Take a look on:

  https://iomega-eu-en.custhelp.com/app/answers/detail/a_id/1235 .

  All the answers and suggestions are provided by an enthusiastic amateur and are therefore no explicit or implicit guarantee. Basically, you use my suggestions at your own risk.