Message "Insert disc" DVR/RW

Similar Questions

• Receive the error message"insert disc" when playing DVD

  Original title: windows media DVD player

  When I try to play a dvd I have message to insert a disc

  Hi Richard,

  The problem persists during a particular DVD playback?

  Your CD or DVD drive is missing or not recognized by Windows or other programs, so you cannot play or access a CD or a DVD. This issue would have occurred after you installed, uninstalled or updated a program or you updated Windows.

  Otherwise, this issue may occur if one of the following conditions is true:

  • You upgrade the computer to Windows Vista or Windows 7
  • You install a service pack Windows
  • You install or uninstall a CD or DVD recording program
  • You uninstall Microsoft Digital Image

  Perform the steps from the link below and see if it works.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 ( )http://support.microsoft.com/kb/322756/)

  Answer please if you have any questions.

• Tecra 8000: Cannot start - Message "Insert disc in the drive system" lights

  I have a Tecra 8000, I've not used for about two months. Now when I try to start the "Disk system to insert in the drive" message on the display. I tried three disks in the system, but they have not been accepted and the same message appears. I visited in the 'setup' and changed priorities and tried to floppy, CD-ROM, HARD disk drive, and the same message every time. Is it possible that the internal battery "backup" is completely flat?

  Hello

  Well, I'm not sure about your suggestion of the bios battery. Usually, you will see an error massage low battery BIOS or CMOS battery low.
  Well, but if the battery is low, so all settings are disabled and the BIOS can't save the changes.
  It's not easy to say what the problem is. If there is something wrong with the material if you ask ASP for help.

• My Dell Desk Top DVD Player does not work. Whenever I have insert the disc and click here to read... I get the message insert' disc Please "."

  What is the faulty drive, or the software that is missing

  Hello

  What happens if you close all programs and then insert the disc?

  -------------------------------------------------------------------------

  If you have problems with CD/DVD drive:

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Error message "insert disc"Trayapp"

  Office runs immediately I get "insert the TrayApp disk" he not cancel, keep coming back.  What is trayapp and how do I get rid of this?

  Look at the thread below for suggestions to correct the problem you are experiencing.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-performance/i-am-having-a-problem-getting-rid-of-trapapp-popup/f5b52346-E548-E011-8dfc-68b599b31bf5

  It will be useful.

• Pavilion DV6 will not play DVD, tells me to insert disc

  When I got my DV6 I could play DVDs. Last week, I burned a few DVDs. Today, I'm playing another DVD, but when I inserted the disc, files, I burned the last time appeared in Explorer instead of the movie. I deleted these files. Now, when I put the DVD in the drive I can hear it turn. But when I click on my DVD drive in Explorer, the DVD tray opens automatically and the message "Insert disc". I don't understand why I can't play movies more. ???

  Hello

  First, try the automated Microsoft fixit at the link below.

  Windows 7

  Vista

  Check if the drive works now.

  If it still does not work, click on the Menu start, open the all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.

  sfc/scannow                (Note that there is a space between sfc and /)

  Let the entire process, then the output type and press ENTER.

  Then, click on the Start Menu, open Control Panel and click Device Manager.  Click to open the CD/DVD-ROM drives.  Right-click on the drive and choose uninstall.  Do not delete if requested drivers.  When the device has been uninstalled click the icon 'Search for hardware changes' (usually just below help in the toolbar).  Let windows reinstall the disc and see if it works now.

  Kind regards

  DP - K

• I use Windows XP and on startup, I get the message insert the disc from center of solutions?

  I use Windows XP and on startup, I get the message insert the disc from center of solutions?

  You have one something or other HP connected to the PC? Check the CD-ROM that
  came with it. Otherwise, contact HP support.

• When I try to play a CD or DVD, the door opens and I get a message "insert a support and try.

  When I try to play a CD or DVD, the door opens and I get a message "insert a support and try. But the anti-virus scan of the device and report No. ERROR. Only play is not possible

  When I try to play a CD or DVD, the door opens and I get a message "the drive is empty. Insert media and try. " But many programs, such as antivirus programs analyzing the device and NO ERROR report. It is not possible to play alone.  No player of media, including Windows Media Player 11 or Windows Explorer does not recognize the presence of the media. I tried with many CD and DVD that plays normally on other computers with similar OS and also on DVD players.

  My computer has Windows Vista Home premium with Service Pack 2.

  Thanks for your reply. It was very helpful / sorry your proposed solution has not solved my problem. Kind regards. -Rajaram77

  Hello

  Click right tab taskbar - task - process - make sure WMPlayer.exe Manager, nor any other
  the player is responsible - in the affirmative PROCESS END on them and try again.

  -----------------------

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  CD have a tolerance + - and your must read on the edge outside these tolerances of discs.
  They may be delivered, but it is generally more economical to replace the disk. Can burn you
  a mastered CD and a DVD mastered on this computer and laptop and other computer
  machines? Can you do the same on the laptop and play in this machine?

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• I am suddenly unable to burn playlists to CD on my MacBook Air. Error message says "Disc burner or software not found" iTunes software is up to date: the current version is 12.4.1

  I am suddenly unable to burn playlists to CD on my MacBook Air. I burned a CD only 2 days ago.

  Error message says "Disc burner or software not found" iTunes software is up to date: the current version is 12.4.1

  Hi BVBigelow,

  I understand that you are not able to burn playlists in iTunes on your MacBook Air. Fortunately, we have an article (link below) which details a number of steps that can help to restore your ability to burn CDs of troubleshooting.

  12 iTunes for Mac: If you have trouble burning a disc

  Take care!

• Can I insert disc HARD 160 GB in Satellite U200-181

  Dear friends!
  If I insert disc HARD 160 GB laptop Toshiba U200-181?
  Version 3.40 BIOS

  Thank you!

  Hello

  Hmmm, comment of the snipe is not 100% good.
  If the size of the HARD drive is not supported BIOS does not recognize the HARD drive!

  I think you could use a HD up to 120 GB, but I'm not sure of the larger sizes.
  You should really examine it until you buy one.

• my Media Player shows no music, or rip music of the inserted disc. What can solve this problem

  my Media Player shows no music, or rip music of the inserted disc. What can solve this problem

  Hey Lucky,

  You can try the steps in the follwoign and check if it helps.

  Method 1:

  You can try to rebuild the media player library, and then try to extract again

  This problem can occur if the media library is corrupt. Rebuild the library and check if this solves the problem.

  Follow these steps:

  a. exit Windows Media Player.

  b. Click Start, run, type %LOCALAPPDATA%\Microsoft\Media Player and then click OK.

  c. Select all files in the folder and then click on Delete on the file menu.

  Note: You don't have to remove the folders that are in this folder.

  d. restart Windows Media Player.

  Note: Windows Media Player automatically rebuilds the database.

  If this does not resolve the problem, disable the Windows Media Player database cache files. To do this, follow these steps:

  a. exit Windows Media Player.

  b. Click Start, click Run, type % LOCALAPPDATA%\Microsoft and then click OK.

  c. Select the Media Player folder, and then click on Delete on the file menu.

  d. restart Windows Media Player.

  Method 2:

  You can also try to change rip settings and check.

  For more information, you can consult the following article:

  Change settings for ripping

• The DVD R/W drive is not recognize the presence of any media in the drive. Whenever I try to play the media, the door opens and I get the message "insert a DVD and try.

  The DVD-R? Drive W is not acknowledging the presence of any media in the drive. Whenever I try to play the media, the door opens and I get the message "insert a DVD and try. Help me fix this error condition, please.

  This has happened a lot of tme, since the last 3 months and I am unable to play any CD or DVD. I have trried Windows Media Player, Real Player, Quick Play and even the free VLC Player, giving the same result unusable.

  Mine is a HP Pavilion 6407dv laptop with Windows Vista Home Premium pre-installed.

  Will be extremely grateful for the quick and useful help.

  Thanks in advance.

  -Rajaram

  Thanks for your reply. It was very helpful / sorry your proposed solution has not solved my problem. Kind regards. -Rajaram77

  Hi Rajaram77,

  ·         Are you facing this problem with all DVDs?

  Try this Microsoft FIXIT who could help you with the problem.
  http://support.Microsoft.com/GP/cd_dvd_drive_problems/en-us

  Bindu R - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Hard drive does not not on the laptop! 'Insert disc in drive D', disc already inside.

  It works fine throughout, but I went on the creation of a hot spare for my laptop computer and any burning, the drawer open and says disc "Insert blank cd in the drive" even if it already, to tried many disks. Tried other discs, games, etc, do not go or recognize a disc inside.

  When I go to computer-> DVD RW drive and double click on it says "insert disc in drive D".

  Tried almost all of the correction he things here http://windows.microsoft.com/en-US/windows7/search?q=vista%20cd%20dvd%20drive&p=1&prd=

  any help is appreciated!

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

• When you try to scan a document on HP Officejet Pro 8500 get the message 'Insert MEMORY' or 'no scan options '.

  When you try to scan a document on HP Officejet Pro 8500 get the message 'Insert MEMORY' or 'no scan options '.

  Original title: I scan a Document

  Hi Robert,.

  The instructions in the article are valid for the model of your scanner. Click the plus sign next to your operating system for more information.

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02450835&cc=us&DLC=en&LC=en&JumpID=reg_r1002_usen_c-001_title_r0001#N6626

  If the problem persists please post the request on the HP support for additional support:

  http://WWW8.HP.com/us/en/support.html

  Please follow these recommended steps and post if you still experience the problem. I will be happy to provide you with additional options.

• When you try to play Rollercoaster Tycoon 3, receive message "no disc inserted".

  Basically, I installed my Rollercoaster Tycoon 3 deluxe edition (edition of Mastertronic). Everything seems fine until I insert the disc to start to play on it and instead of opening, he said: "no disc inserted". My CD/DVD drive works fine I have tried other discs and they seem to work perfectly, so I'm confused. I also tried to uninstall disks, controllers, etc. Help, please!

  * original title - no disc inserted? Please help! *

  Hello

  1. check the disc.
  2. check the disk drive.
  3. make sure that the disc is clean.
  4. once ive tried to play the game when there was already another cd in the drive (check you have not done the same thing)
  5. ^ ^ ^ I was tired, it was early in the morning, do not laugh
  6. check there is no cracks or scratches on the disc
  7. try to wipe the hard drive.

  The thread I linked below tells you what must be applied updates
  http://forums.frontier.co.UK/showthread.php?t=3

  then your version of the game should be: 3.0.12.58, if this is the case, then you need to update I've linked below:

  FTP://ftp.Infogrames.net/patches/RCT...PDATE3_USA.exe

  Note that these updates only work with the version of the game disc