Modem or router is not available

Similar Questions

• For two days, unable to get maps of Google with Firefox. The page opens, but the route is not available. With Safari, no problem.

  For two days, unable to Google Maps works with Firefox. The page opens but no answer to my questions. A message says "loading... Lai is too long? Look at troubleshooting guide or simplified HTML version. »
  No problem with Safari.

  URL of affected sites

  http://maps.Google.fr/

  I had the same problem. Reset the browser.startup.homepage_override.mstone in all: config. The problem is corrected.

• Linksys wireless router is not my new Motorola modem Internet access

  I am relatively new to setting up home networks, so it's maybe a stupid question but I'm stuck! I bought a new modem Motorola (SurfBoard 1621) as my old Motorola modem was not favorable to the increase of the speed offered by Comcast. The modem I bought was a model recommended by their web site. They recorded the new modem last night and I can access the Internet when the PC is connected directly to the modem, but not when the laptop is connected to my Linksys wireless router. (Sorry, I don't know the model because it is at home and I'm at work!) Is there something I should do for the router to recognize the new modem? The router recognizes the wireless laptop, but it can not connect to the Internet.

  Thanks a lot in advance for your help.

  Success! Thanks a lot for your answer. My router is a WRT - 54G links.

  The instructions were very informative, although I have a suggestion. Just restart the modem and the router did not work. I had to reboot other equipment in my system (a NetGear firewall and a level switch 5 ports) and the router and the modem. I would like to see the reboot of reference tracking "and other devices. I guessed the appropriate power of sequence (modem, firewall, switch, router, computer), and fortunately, it worked.

  Again, thank you for your quick response.

• Router is not connecting to the modem so I can't get internet

  All right-_ - I tried a lot of things with this so I get irritated sorry. Here is my info I have a Linksys Wireless Router with SpeedBoost Firmware Version 7.2 WRT54GS (latest version). I'm trying to use it with a Sprint 645 series Modem. My IP address when you are connected to the router and the router connected to the Modem is 192.168.1.100 who my ISP said was ok to make it work. While it is just connected to my modem, it's the same thing except replace the 100 by 1. My ISP uses a measure of security where The Thing DHCP is 192.168.1.1 and so is the DNS server and default gateway and im not sure if this has something to do with it. I used the ping at a command prompt to make sure that I am connected to the router when its plugged up and it is. This is a new router. I have internet with Modem just perfectly. I tried to reset the router and that does not work-_-. I don't think it is important more because I tried to fix the many way people have told me and it didn't work, but I'll tell u in any case. When I put up the first router time I hung and lit everything at the beginning. Then I noticed that it says Run CD before to connect the cables... those who were not in the instructions but wtv... anyway resetting should have fixed or so I was told by other people on this forum. I use a laptop with Windows Vista, and I don't have access to a desktop computer in case I need a XD. I can connect to the router fine because I can access the Setup page... and I can connect wireless... The ONLY problem seems to be that the router will not connect to the Modem... for some reason of wtv-_ - I think that its because the entire security measure on the way to the DHCP and the DSN and the bridge are all 192.168.1.1, but that's just me. I'm sorry this is very long but I really want this problem-_ - I had this router for a month and becomes really annoying so please help . My ISP is Embarq. I ran the installation CD and I had all through the last step (standby router) after having connected the power supply to the wall for the router. Just, it is there forever and then says "error: 322 cannot find router or something like that." There are 3 steps to try to fix it. It says to make sure that the router is connected (it is), it is said also to make sure that u does not actually connect your old router, (I don't have a-_-) and then re-run Setup. and by the installer, I mean where u plug in all the cables in the right way. * sigh *.

  If you need anything else please ask.

  Your second post says "" ignore this "so I guess everyone thought that you set..."

  When you connect through your router that you have two instances of DHCP past... one is your DSL modem with router IP address on its WAN interface. The other is the router that gives your computer an IP address via the DHCP server on the router. The IP address of the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the reange of Linksys routers LAN IP address is also in this range. For that to work, you must set your router 192.168.2.1 LAN ip, so that the LAN and WAN router interfaces are in different networks.

  To do this, unplug the DSL modem router, power it and your computer, and then connect the computer to the router by an ethernet cable. Turn on the router and the computer, and then go to 192.168.1.1. Change the LAN IP on router 192.168.2.1, save the configuration, and then restart the computer. Once the computer returns to the top, navigate to 192.168.2.1... you should be able to get to the router GUI configuration.

  Turn off the router and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, and then turn on the modem, then the router... you should be good to go...

• Error code 797: connection is not available because there is a problem with your network card or modem

  I have a Windows 7 laptop. I use broadband (DSL) to connect to the internet. Lately, I have an error with the code 797. It says connection is not available because there is a problem with your modem or network card. I have a Sony Vaio e series laptop.

  Hi Muffakham,

  Thanks for posting your question in the Microsoft Community forums.

  I see from the description of the problem that you are unable to connect to the Internet and receive "Error Code 797 connection is not available because there is a problem with your network card or modem".

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  To provide the proper resolution, that I would need more information on your side.
  Did you the latest changes on the computer before this problem?

  This problem may occur because of damaged or incompatible, drivers connection settings incorrect network, hardware or software problems and missing updates.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Method 2:
  If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check out the link for more information.

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know the status of the issue after you perform the troubleshooting steps. If you need information about the problem with the connection to the Internet or get help, I'll be happy to help you. We, at tender Microsoft to excellence.

• My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless.

  My wireless router does not appear when I shoot to the top of my devices. It shows my fax, modem, scanner and a few others. But not my belkin wireless. And when I try to add it, the system can't find it. Please help

  Belkin support for your model, for installation instructions.

  Your router will not appear in the devices

• My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available.

  My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available. How can I permanently?

  Hello

  1. who is the operating system installed on your computer?

  2. are you using a cable or a wireless Internet connection?

  3. were there any changes or updates made on the computer?

  4. what store did you try?

  Follow the steps mentioned below and check.

  Method 1: I suggest you to return the item and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  You can try resetting WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.

  a. Click Start and in the search box, type cmd.

  b. right click on command prompt, select "Run as Administrator" to open a command prompt.

  c. at the command prompt, type the following commands:

  netsh winsock reset catalog, which resets the WINSOCK entries to the default installation

  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation

  netsh int ipv6 reset reset.log resets the IPv6 TCP/IP stack by default installation

  d. restart the computer.

  Method 3:

  Reset the default router by pressing the reset for 15 seconds with power button.

  a. turn off the modem, the router and the computer.

  b. connect the modem to the WAN/Internet port on the router.

  c. connect the computer to one of the router's LAN/network ports.

  d. turn on the modem, wait for triggering connect light.

  e. turn on the router, wait two minutes.

  f. start the computer.

  g. when the computer is completely loaded, check if the problem persists.

• Cannot get on internet, ebay or by e-mail. Get a message that says - Web page not available-. How can I fix th

  Cannot get on internet, ebay or by e-mail. I get the page that says - Web page not available-. How can I fix?

  Make sure that you are connected to your WiFi network and make sure that an internet connection could be established since the modem (the area where past the line cable or phone) and the router (the box that connects to the modem via ethernet).

• Photosmart Plus B209 wireless connection not available

  Hello

  I just got a new Photosmart Plus B209 because my old 4580 died. I had the old printer put in place for the wireless connection, but the new Photosmart told me that the network is unavailable. When I press help he told me to make sure that there is no connection and to check for interference. Well, there are none. Printer and router are almost side by side. I used the HP set up guide and he tells me that the network is not available (which it isn't because otherwise I wouldn't be able to write this online).

  I use a MacBook with a Timecapsule 10.5.8 and a cable modem D-link.

  Yes, the workaround is a bit tedious, but it works.  If you have another router (standard), we all connect to one and use WPS.

  In any case, let's try this:

  1. on the front of the printer: Setup > Wireless > default settings.

  2. on your look of computer for a wireless called "hpsetup".  Connect you to it.

  3. print a network Test Wireless in the menu of the wireless printer.  Get the IP address of the printer.

  4. type the IP address of the printer in the web browser address bar.  You should see the page in the printer settings.

  5. click on the network tab, and then start the wireless configuration wizard.  Follow the instructions.

  6. when the printer is connected to your wifi, re - connect your computer to your wifi and add the printer in system preferences > print & scan (click the sign '+' to add the printer).

• Remote Assistance error: "Easy connect, not available.

  Original title: easy Remote Assistance connect will not work

  I have 2 systems of windows 7 on a local network using Qwest PK5000 modem-router.  Both systems are connected via the home network and share files between them very well and there is only 1 active network.

  If I run the MSRA command on the 64-bit computer and select easily connect using the option "help somebody", the system displays the security code for the other system to use or "invite".

  On the 32-bit machine when I try either options it goes to the "easy connect, not available.  Network Diagnostics has found no problem, but if I try to access the Internet connectivity evaluation tool I can't in the tool.  It says at the bottom "IE6 is required" and nothing happens.   So I don't know if the PK5000 was the Peer Name Resolution Protocol on it or not.  Qwest or Actiontec will not respond to the request.  I guess it's OK if the 64, but the machine would not immediately come with the password to use on the other machine.  The command ipconfig/all look the same on both machines. Furthermore, both systems are (Inspiron 580) and DELL (XPS 420).

  Please give me more advice on this problem.

  Problem solved!

  Downloaded "Teamviewer.exe www.teamviewer.com.  It is a product of superior quality on remote assistance and is free for non-commercial use and it works great both ways. And it allows control over the other system instead of simply consider.

• Error Windows 8 "default gateway is not available".

  Original title: standaardgateway is niet available

  Windows 8

  now Internet then stops and begins again with appreciated: says "standardgateway is not available.
  What can be the problem? Who knows the real solution?
  Default gateway is your router/modem

  McAfee can cause this

  If you do not have McAfee try resetting your modem/router
  Call your ISP and tell them that your router is doing this and ask for replacement

• cable modem-wireless combination or not?

  Hi, I'm going to switch from DSL to cable T - W (the only option in my building). I have an Airport Extreme on my TimeCapsule (it is the 500 GB disk version), that I use with my laptop. The iMac is connected to the router. I looked around at best buy where they sell T - W "approved" networking gear. Modems cable, all seem to be modem + units of combination of WiFi router at various points in price between about $80-200. My question is this: that any type of material that I use as long it's T - W compatible/approved. Any thoughts on the units of combination or is a cable modem + my Airport Extreme way to go. Not sure of the speed yet, but it is unlikely that I will contract for what that either more than 50 Mbit/s and perhaps even to 15 Mbps. Support some of the Motorola units that I was looking for very high flow rates, but they use the channel binding to achieve this goal. I read somewhere that if you buy the combined devices, you cannot update the firmware, but that doesn't make sense to me.

  Ask TW a modem without router built-in. And then run an Ethernet cable from the Ethernet port of the modem on the WAN on your AEBS port. You can connect your computer to the router either wired or wireless. It is the best configuration.

  If you do not need for Ethernet, then you can use a modem cable with router Wi - Fi as well. The main disadvantage is the difficulty you might have try to expand the modem/router using Apple hardware.

• drive time capsule is not available

  The time capsule disk is not available.

  Finally, he worked on 08/08/2016.

  If the capsule is on a wireless network, other devices work on this network? Have you checked your settings on the screen of Airport utility? You've restarted the router?

  The time Capsule is the computer wifi range? Time Capsule shows a green light?

• Network accounts are not available

  Hello

  I work in a corporate environment that is mainly based on Windows, but also have a handful of Macs and a Mac server. The question I have is that the MacBook display the prompt "network accounts are not available" when connecting. This message disappears when the VLAN from requiring authentication on our firewall device, MACs are to be excluded.

  I thought my our support company firewall that Macs are a kind of test at startup. If they do not have full access to internet NETWORK card wireless goes into a State of semi functioning. It is only when they have access to the internet it goes into a fully operational.

  It makes sense when the "network accounts are unavailable" message, I can't SSH in the Mac, but can't ping the IP addresses of our DC, ping any name FULL domain or ping any device outside the VIRTUAL LAN. Does exactly the same as this -after-reboot-no-route-to-host http://apple.stackexchange.com/questions/231290/mac-unable-to-login-network-user

  Our company firewall just remember exactly what service performs this function on the Mac. Anyone know what it's called?

  Kind regards

  Peter

  Any help here...

  http://osxdaily.com/2007/01/22/what-happens-in-the-Mac-OS-x-boot-process/

  During his execution, rc.boot and the other rc source of scripts /etc/rc.common , a shellscript that contains utility functions, such as CheckForNetwork() (check if the network is in place), GetPID() , purgedir() (Directory deletes the content only, not the structure), etc.

  • rc.bootfigures on the startup type (Multi-User, Safe, CD-ROM, network etc.). In the case of a network boot (the sysctl variable kern.netboot has the value 1 in this case), it works /etc/rc.netboot with a start argument.

  /etc/rc.netbootmanages all aspects of the network boot. For example, it runs the network and (as applicable) supports the. It also calls /usr/bin/nbst to associate a file of the shadow in the image of disk used as a root device. The idea is to redirect the entries in the file of the shadow, which hopefully is local storage.

  • rc.bootnumbers if a file system consistency check is necessary. Boots single user and CD-ROM does not run fsck. SafeBoot is still running fsck. rc.bootmanages fsck and return status.
  • If rc.boot has finished successfully./etc/rc

  http://Hayne.NET/MacDev/notes/boot_sequence.html

• the device has been disconnected or is not available

  I can detect the modem Huawei E173 usb and install following the instructions, but when I try to connect, watch the device has been disconnected or is not available.

  Help, please!

  Currently, my version of the MacBook has been OS X 1 10.11.4

  its MacBook Pro OS X 10.11.4