MOUSE KEYBOARD DISABLED N

Similar Questions

• USB mouse & keyboard disabled randomly after the Windows 7 login Panel

  Hi all

  Randomly, after the Windows 7 login Panel, windows disables my keyboard and USB mouse.

  -No problem in BIOS or on the login Panel, but once the credentials entered and valid, and reaching office, mouse and keyboard (USB) close

  -To solve the problem, I need to reboot several times, waiting for an instance where my devices are not closed (so it works without any pb until the next reboot)

  -J' have a backlit keyboard and when the problem occurs, light are turned market, as if it was turned on and turned off randomy

  Searching the Internet, seems, I'm not the only to encounter the problem, however single chip found Advisor on these was mentioning it is a bug in Microsoft Windows 7, associated with the management of the power supply of the USB ports. However the advice provided to change the config to disable these judgments do not work...

  Thanks in advance for your help and best regards

  Fabrice

  Have you tried to go to safe mode with networking Mode and update your USB drivers?

  You didn't say you had the problem goes mode without failure, so it might be a solution for you.

  USB drivers should be found at the web page of the manufacturer of your computer or your motherboard manufacturer's web page.

• Mouse & keyboard does not not after waking from sleep

  This problem started about 6 weeks ago, and I've exhausted all remedies except that maybe a Win update caused the problem with updates of November.  It only would be not the first time a Win update caused a problem.

  I am running Win 7 Professional 64 bit, 3.4 processor concert image, 16 gig RAM and 24 concert page file.  This occurs only when everyone is connected and puts the computer in "sleep mode" all connected, and that includes letting go the computer in mode 'sleep' a timed framework, or by using the command Win to sleep or Sleep.com.  It does not occur when you cold start, warm boot, or log off and then put the computer in standby mode, and that includes using the key on the keyboard, programmed to the Sleep.com or Win command.  In these cases, everything works fine even wake up the computer when it is disconnected.

  If I put the computer in mode 'sleep' while connected and then when I press a key or move the mouse, the computer will wake up and I get the login screen since I'm protected by Word.  The lights on the keyboard light (wired 4000 natural ergonomic keyboard) and the light on the background lights of the mouse (Wireless Mobile Mouse 4000) so I know the two USB ports are powered.  However, when you press any of the keyboard to type in my password, it does not display what I typed and the mouse cursor does not move. Both are totally insensitive.

  Short reboot, the only is to unplug the USB cable from the keyboard as well and the mouse receiver, wait 10 seconds, then reinsert them.  When I do that, everything works as it should.  It is a pain in the back since both are on the back of the computer.

  I tried using different USB ports, mouse & keyboard Centre of the reinstalled several times, checked all drivers, run ' sfc.exe/scannow"which doesn't show any problems with the system files and Device Manager has assured times checked to allow them to turn on the computer and made sure any setting relevant to the USB ports or peripheral interface that have the option to"Allow the computer to turn off this device to save power"are disabled.

  This is of course only related to someone to be connected, because it works very well when that I disconnect.  This tells me that's not the BIOS, as suggested by older discussions.  If it was the BIOS, then there is a problem when you do a cold or warm boot.  Also, I have the BIOS configured to recognize all USB devices when starting and not only ports keyboard or mouse.  The reason for this setting must be my hard drive to backup (USB 3.0) available at startup.  I checked everything I can think in the registry and can't find anything that could cause this.  I have hibernate off (never use it and it uses 10 GB of disk space for the file), and the implementation of the options for "USB selective suspend setting" is set to off.

  My solution is as follows: I disconnect, and then put the computer on "standby".  When ready again, I have simply to move the mouse, type my password, and Windows opens with the mouse and the keyboard works as it should.  It takes a little longer to wake the computer if it was put in mode 'sleep' when you are connected with the exception of the time and the hassle of having to unplug the mouse & keyboard, but I don't have to jump through that hoop to make it work.  Up to 6 weeks ago that this computer was fine with the same exact material because there now.  In the night, I just put it in "sleep" mode when connected from the computer has a task in Task Scheduler that wakes up the computer by running the insomnia (to keep him awake for backup) and backup programs runs, then shuts down the computer when finished.  This works because I do not use the keyboard or the mouse as I SLEEP.

  I would be grateful for any suggestions!  I'm a user for more than thirty years (even go back to the PMO for those of you who know what it was), built my own computers for years, so I can handle everything that needs to be changed.  It intrigued me, and I don't have very often coming up with computers.

  PROBLEM SOLVED!

  I thank very you much for working with me and remember to do things.  Sometimes techies like us, as they say, 'can't see the forest for the trees' If you know what I mean.  It's like the authors of the software manual do sometimes in that they assume you already know the steps has a B, and they begin to step C.  Sometimes it is more obvious that we see because we are looking for something more complicated.

  I had already tried another keyboard and a mouse, and I thought some time ago, I did a clean boot, because I know that can open the door and where is the problem.  If I did, I forgot or did not find the problem.

  I apologize for him accusing Microsoft of having caused the problem with an update, but I've had this happen before and thought that it had happened again.  It turns out that it was a software problem, but not here where I thought it was.

  After doing a clean boot and noting that the computer and the mouse worked after the return of the mode 'sleep' with a clean boot, I knew there must be something to load into memory and showing in the notification area.  The only things I had done in the six weeks was to add a quick Weather Channel.com Weather app and I had exchanged and received my new SkyCaddie.  It is a portable device that shows the yardage, etc. on the golf course.  The SkyCaddie uses a program called CaddieSync Express that allows the device to communicate with the web site to download updates of the course, the software updates, etc. scores.  The version of the program used on my old unit had a problem after I unplugged in that when you open Internet Explore nothing would show - no communication with the web.  I had to sign out and then sign back in and then fix it every time.  It seems that in this new version the problem has been resolved, but they have created a new.

  By default, the program loads into memory and the icon appears in the notification area.  When you connect the SkyCaddie using its USB cable, the program recognizes and prepares to synchronize.  The problem with this new version, is that even if you do not use the synchronization program, this is what prevents the keyboard and the mouse works correctly.  It must focus on a USB hub even if you do not use.  The solution was to go to the configuration of the system to prevent this program from loading at startup, it placing a shortcut on the desktop and then clicking this shortcut to load the program prior to attaching the SGX.  I then let him do his thing, and when it's over and I disconnect the SkyCaddie from the USB port, I close the CaddieSync Express icon. and then when I put the computer to sleep and then wake it up, the keyboard and mouse work fine.

  I knew that I had installed the new CaddieSync Express all the time, this problem started, but I never thought about it because he had never caused this problem before the cause of the problem.  Trust me, they will receive a call from me tomorrow so that I can tell them that the problem they cause.  Remember what I said in the first paragraph.  They would not yet be aware of the problem, and maybe after I speak with people of their software, they'll send an email informing the owners of this problem until they get it fixed.

  Now, since systems vary so much, including how are managed USB hubs, this can occur only in rare cases.  I came just to be one of these.

  Thanks again!  Perhaps some of these other people who have posted in the forum who had the question keyboard & mouse will read this thread and it will help them solve their problem.

• Pavilion 15-p079no: HP Pavilion 15-p079no keyboard disabled

  I posted this first portable other issues, but it seems that is better suited for her

  Hi, I had this problem with my laptop (HP Pavilion 15-p079no) since yesterday. I don't really know where the shoe pinches.

  The problem is that the keyboard stops working after that I connect with the computer. Before you connect (Windows 8.1), all the keys work perfectly well. However, after the signing, they stop working. When I try to press a key, the computer lets a little voice from the speakers, this pretty much signaling that the computer recognizes the keystrokes, but just do not do anything.

  I doubt that it is a hardware problem, given that the keyboard works perfectly fine until I have decide to open a session. But what causes the keyboard disabled, and how to activate this new?

  Hello

  As the keyboard works until you connect, check the following.

  Open windows control panel and on the top right, next to the display by: select "large icons".  In the new page layout, select the "ease of access Center.

  Select the option "make the keyboard easier to use".

  If there is a check mark next to 'Turn on filter keys', click the box to Remove , and then click apply and then click Ok to save this change.

  Kind regards

  DP - K

• World of Warcraft Launcher "screen freezes, mouse & keyboard»

  I have two accounts North American & European World of Warcraft & loaded on my comp. previously Ive a had no trouble to have access to the either. Now, the European launcher 'freezes' my beginning of solange screen my mouse & keyboard are also frozen, I have to re-boot because I can't do anything. I have carried out a diagnosis of the system and saw there are programs/conflicts/sharing items.

  Any thoughts? & How to resolve these conflicts? I have run Avast Anti-virus, but turn it off for the launch, but same problem persists.

  These are:

  (resources)                                               (Device)

  Bus i/o PCI Port 0 x 00000000-0x00000CF7, Direct memory access controller

  Port of e/s 0x000003C0-0x000003DF VIA CPU to AGP RADEON 9000 SERIES

  IRQ 21 VIA Rev 5 or later USB Universal Host Controller

  IRQ 21 Standard PCI enhanced USB host controller

  PCI bus memory address 0xA0000-0xBFFFF, VIA CPU to AGP Controller, RADEON 9000 SERIES

  Port of e/s 0x000003B0-0x000003BB VIA CPU to AGP RADEON 9000 SERIES

  Hi Rastifann,

  ·         Did you do changes on the computer before the show?

  If the problem occurred after making all changes, then you can check and restore the system.

   

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  You can also contact the game support for help on the issue.

  Let us know if that helps.

• USB mouse & keyboard stop working after the upgrade of Intel generic drivers drivers!

  Original Post: USB mouse & keyboard stop working after upgrade to generic drivers

  After you install Windows, the Generic USB controller drivers are installed. My mouse & keyboard as planned work & that are each recognized as "compatible mouse/keyboard HID."

  After I installed the Intel drivers for root USB controller, the mouse & keyboard stop working and are classified as unknown. Shortly after, they are considered HP USB Optical Mouse & HP USB Standard keyboard, however the drivers never properly install and they remain under unknown devices with a yellow exclamation point.

  I have searched high & low for these device drivers, they do not exist. I installed the drivers for all of the materials appearing on the site of the seller. This has happened on several computers, laptops and desktop computers.

  I've done all the troubleshooting I can think. Uninstalled all the controllers/USB hubs & restarted. Switched USB ports, I tried new mouse & keyboard, wanted Windows updates.

  The only way I can make it work is if I use the generic Windows drivers, who then recognized the mouse & KB "HID compliant". It seems that if I install Intel drivers, it recognizes the mouse & keyboard more in detail and he wants specific drivers to continue.

  Any help / suggestions would be greatly appreciated.

  Thanks for the reply.

  Because your computer is on a domain network, it would be better to be posted on the TECHNET forums. They are experts in your field of investigation and would be in a better position to answer your concerns.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=w8itprogeneral&filter=AllTypes&sort=lastpostdesc

  In the future if you have problems with Windows. Not to contact us. We will be happy to help you.

• How to change the mouse keyboard and mouse wireless in one click?

  Original title: How can I change the mouse to a single click? more it is difficult for an older person with arthritis.

  I would change the mouse keyboard and mouse wireless in one click. I have windows7. with windows xp, it was part of the accessibility options, but I can't find this option now. Any help would be appreciated. Thank you

  Hi knufyn,

  I certainly understand your concern and I will be happy to provide the steps to check if we can change the settings click on the mouse.

  Let us, perform the following steps and check if you are able to change mouse click settings.

  By default, the mouse is configured to use the double-click to open an item (single click to select) in Windows 7. To configure the mouse to use the single-click to open an item (point to select) setting, follow these steps

  un) Click Start

  (b) type appearance and personalization in the start search box, and then click appearance and personalization in the list programs.

  Note: If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  c) in appearance and personalization, click on Folder Options.

  d) in the general tab, click single-click to open an item (point to point)

  (e) click apply and click OK.

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• disabled bluetooth. No mouse, keyboard, trackpad how to ACTIVATE

  NOT DISABLED BLUETOOTH NO MOUSE, TRACKPAD, KEYBOARD, HOW CAN I TURN ON

  Turn off your computer, make sure that Bluetooth devices are on, then start up the Mac. It should detect the devices.

  If this isn't the case, you need to use a wired keyboard.

• Satellite C50-A-1DV - mouse / keyboard problem

  Just bought this laptop and have heard of problems with the keyboard and mouse.
  It happened to me today.

  The mouse stops just in response to the movement of the keyboard.
  Thought that update of Windows 8 may have changed / added something so this causes rolled the driver in Device Manager that was available as an option, but now is not.

  The mouse still works sometimes and sometimes not. If I press F5 it sometimes is.

  using the FN and F5 took me to the keyboard layout where I set the keyboard to the default setting and it worked well for a while and then stopped again.

  Someone suggested removing the battery and now the switch for 20 seconds, but has nothing actually. Is an appropriate solution for this outside assistance from a separate mouse?

  All thoughts welcome.

  Thank you

  Dave

  Hello Deborah

  The touchpad could be simply disabled in case where you have not checked it in the past, the combination of keys try Fn + F5 to switch from a touchpad on/OFF function.

  In case this does not resolve your problem, reinstall the electric Synaptics and Alps Touchpad driver.
  Both can be found and downloaded from the Toshiba UE driver page:
  http://www.Toshiba.EU/innovation/download_drivers_bios.jsp?service=EU

• Macbook Air using with mouse, keyboard, and external display?

  I want to put in place a more ergonomic work station. Can anyone recommend how I can configure my Macbook Air 13 "to use at home with an external monitor as well as an external keyboard and mouse? What is the easiest and most cost-effective way? Is a necessary dock if I buy a bluetooth mouse and keyboard, then simply plug the monitor each time? Could I use this set up with my macbook screen closed? I bring my Macbook to every day, so it must be easily plugged/unplugged. Thank you.

  A dock is not necessary. If you use a USB keyboard and mouse or a BT, it is up to you. I use a BT Magic Mouse and Apple keyboard in my office. That leaves just two things to plug: monitor and the power cord. When you use an external monitor as primary monitor you can close the lid of the computer and it will not go to sleep.

• DELL U2713H and MBP mouse/keyboard

  Hi all, I have a DELL U2713H monitor connected to my MBP via an HDMI cable. I would like to connect an external keyboard and mouse on the monitor and have these devices to be picked up in the MBP via the HDMI cable. Is this possible?

  I want to make sure that I have the fewer things to unplug it when you take my cell phone with me and have the less things to plug in when I get back.

  Thank you!

  No! I'm sorry. HDMI is Audio and video. Understand what you're trying to do. A complete Apple wired keyboard would cooperate with a Magic Mouse or Magic Trackpad. Or keyboard and mouse/Trackpad Magic.

  Bravo!

• Entered mouse/keyboard not appearing is not in Firefox

  I recently got a new laptop from my place of work. I installed Firefox 10.0.2 and started to install the usual addons/plugins (adblock, read it later, flash etc..).

  After the restart of the browser, firefox has started to enter a mode of 'blocking' He is not suspended by itself, but none of my actions of keyboard or mouse appear on the screen. So, if I type in the URL "Google.com" box and press ENTER, the url box is left blank and the screen remains blank.

  However, if I resize the window (or make it full screen), the actions that I entered (typing google.com and press on enter) have already taken place. The display then shows google page, waiting for an input on my side. Thus, the program took to my entries but there is not the shown on the screen.

  I tried to reinstall the program and past firefox 11 but the problem continues to persist. Other browsers such as Chrome and IE9 properly. Even after uninstalling all the plugins and addons and re - install the application, the entries do not appear in firefox. As a result, I now have to use Chrome (boo!)

  Any help guys?

  Hello

  Please try deselection to use hardware acceleration where possible (Alt + T) Tools > Options > Advanced > general. Options > Advanced

  Options

  If the problem persists, please check if this happens in a new profile. If the new profile is correct, you can later copy the necessary personal data of the old profile. Firefox stores your personal data and settings to another separate location of the files/folder. A new profile would default Firefox settings (Tools (Alt + T) > Options, and topic: config ) and usually also would be vacuum of Extensions and themes (appearance) in tools > Add-ons) and their parameters. In addition, a new profile would have no previous website stored data/settings etc, (Tools > clear recent history).

  Profiles Howto

  Files & profile folder

  Subject: config entries

• lost USB for mouse keyboard... where can I get another?

  Fore lost usb mouse and wireless keyboard. Where can I get another? And what size spec for HP Pavilion 23?

  Most manufacturers offer replacement, or dongles, receivers for their mouse and wireless keyboards. You should visit the Web page for the manufacturers of your mouse and your keyboard. Your HP Pavilion 23 a of the USB 3.0 ports that are compatible with all previous USB connections, so no matter what USB receiver will work in the machine.

• Satellite M50 - YK4 plug and play mouse/keyboard

  I tried to use a USB keyboard/mouse for my laptop, but windows does not recognize it. They are peripheral universal plug n play and yet it takes me to the "new device found". I also tried to buy keyboards with software and despite the installation, the new hardware wizard still appears upward. When I try to install the drivers, it gives me just an error message (Code 10, device cannot start). When I bought my laptop, I could use my usb mouse and keyboard without problem, so I think that it's the corrupt drivers. All USB ports are working fine and my IPOD and phone, printer also work. Any help on this would be appreciated.

  Try to remove all associated USB drivers. Go to-> Add/Remove Programs Control Panel.

  Installation of the keyboard and USB mouse driver can cause problems, then remove both drivers. They work very well using the standard mouse and keyboard drivers.

  Another thing you can try is to reinstall the Intel Chipset driver.

• Mouse-keyboard blocked

  Hey

  I have a lenovo ideapad Z570. I was very happy with the product... But, today my mousepad has been stuck at regular intervals... When I press a key on the keyboard, the mouse comes off... and then after a few minutes, its stuck again.

  Keys on my keyboard are also stuck I'm typing this.

  Hoping you have a solution to this problem

  Thank you.