MX800 Conferencing Multisite

Similar Questions

• SX20, MX200G2, and MX300G2 consumes same bandwidth as the SX80/MX700/MX800?

  Guys,

  If I understand well SX80/MX700/MX800 H.265 codec has put in place and then have half of bandwidth consumed compared to the older codecs. I noticed for a while most video conferencing codec Cisco including SX20, MX200G2/MX300G2 data sheet has band bandwidth information updated with 720p30 with 768 Kbps. This average series SX20 support H.265 also? Or it's just the mistake of plug technique Cisco?

  In addition, when these codec supports H.265 talk to MCU or webex RMC, they will always use double bandwidth because the other end does not support H.265 yet, correct?

  Thank you.

  Lou

  H.265 is only supported on SX80/MX700/MX800 and only when using SIP.

  Once you call a device, or introduce a device in the call that does not support H.265, well, so he won't need to use it.

  720p30 at 768 KPS is not full HD, is not a mistake.

  is 1080 p full HD, and to do this you will need a lot of higher bandwidth, and that's where all the benefits of the H.265 kicks in which can give you full HD at a lower bandwidth.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• How fees are there for audio conferencing in microsoft live meeting

  how much should I pay for audio conferencing in microsoft live meeting. Waiting for your response.

  Concerning
  Shonan systems

  Hello

  I suggest you contact Windows Live Meeting customer support, see the support below link:

  https://support.live.com/default.aspx?ProductKey=mocplmhome&brand=MOCP&&mkt=en-us&scrx=1

• Video conferencing does not work with the voice gateway PVDM3?

  Hello world

  I'll create a meetme conferencing. However, what config it use VGA, audio conference is only allowed

  Here's the material:

  • PVDM3-32 x 2
  • VIC2-2FXO
  • VIC3-2FXS/DON'T
  • 9971 ip phone x 3

  Here is the config VG (work),

  VG (config) #.
  !
  voice-card 0
  dsp-booking voice-service 6
  !
  dspfarm profile 1 homogeneous conference video
  Codec g729br8
  Codec g729r8
  Codec g729abr8
  Codec g729ar8
  Codec h264 cif-cadence 15 bitrate 128 Kbps
  maximum of participants at the conference 4
  maximum 1 x 1 layout
  maximum sessions 1
  associate the PCRS application
  !

  Here is the config VG (failure),

  VG (config) #.
  !
  voice-card 0
  dsp-booking voice-service 6
  !
  dspfarm profile 1 homogeneous conference video
  Codec g729br8
  Codec g729r8
  Codec g729abr8
  Codec g729ar8
  Codec h264 vga-cadence 30 bitrate 1 MB/s
  maximum of participants at the conference 4
  maximum 1 x 1 layout
  maximum sessions 1
  associate the PCRS application
  !

  Here is the result of the test with different codec

  • OK - h264 qcif-cadence 15 bitrate 128 Kbps
  • OK - h264 cif-cadence 15 bitrate 128 Kbps
  • Fail - h264 cif-cadence 30 bitrate 704 Kbps
  • Fail - h264 vga-cadence 30 bitrate 1 MB/s

  When you use the Cisco.com DSP calculator ,
  1 profile of videoconferencing
  Session number: 1
  number of participants: 4
  Conference type: homogeneous - 1 class
  H.264 VGA: checked

  It returns:

  Allocation of Module DSP:
  Router Slot 0: 16 video (25%) 4 votes (7%) 44 available (68%)
  PVDM Slot 0/0: PVDM3-64

  So, why can't I use the VGA with PVDM3-64?

  Thanks in advance

  Sam

  Do not forget this:

  Announces Deprecation feature video conferencing and transcoding using PVDM3 on the product for the ISR G2 Bulletin

  http://www.Cisco.com/c/en/us/products/collateral/unified-communications/TDM-gateways/bulletin-C25-735945.html

• No point endpoint name when SX20 Multisite conference

  Hello

  I have install a lab which consist of 2 SX20 and 1 EX60. Using SIP and any call control, trying to conference with capacity multisite SX20 (just call using the [email protected] / * /). But, I noticed there is no display name below each participant in the video. Is this a normal behavior? I configured the name displayed on each endpoint.

  Yes, this is a normal behavior.  The names of the participants will be displayed when you use a microcontroller, and if it is configured to do this.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• The differences Multisite and Multiway conference

  Hi all

  Can you tell me what are the multi-site and multiway conferences? Also, what are the differences between these conferences?

  Multi-site allows an end point to host a conference using a microcontroller embedded on the endpoint for a limited number of participants, usually not more than 3 depending on the type of endpoint and requires a key Multisite option on the endpoint, which is hosting the Conference, which allows you to use the embedded microcontroller and not every endpoint support the Multisite functionality.

  Multiway allows you to climb a call to a call from point to point-to-multipoint call, endpoints and requires a VCS for climbing and MCU to host the Conference. You can learn more about Multiway of Multiway using Cisco TelePresence systems.

• Resolution always falls on a multisite call if a Premium license is active?

  Hello

  Multipurpose codecs, the resolution will drop when a multisite call is established using the multisite aboard hook function.  Chip resolution steps for the bottom of endpoints:

  Changes of SX20 resolution to 576 p 30

  C40 resolution to 576 p 30 changes

  Changes of C60 resolution at 720 p 30

  C90 changes resolution 1080 p 30

  If you apply a Premium resolution license to the codec, the resolution still drop?  are they the same?  or at least get bumped slightly higher?

  If it does not increase the resolution, how does it increases for each model?

  Hi Kris,

  It will still drop, regardless of PR - key.

  Thank you

  Marius

• C40 Multisite call

  Hi all

  I have to configure multi-site/multiway,

  We have VCSC and MCU.

  and endpoints such as C40, ex90 and MXP1700.

  Ex90 has licence Multisite for C40, but it's not. Able to make P2P calls and then add other EX90 IAM conversation endpoints.

  We have a VCSC and MCU.

  How can I configure multiway help MCU?  I tried to set up an alias in VCS, Conference factory-22228

  and the model [email protected] / * /

  Conference factory State is active. 22228 added as base10 multiway on the c40. My prefix for MCU Conference Service is 8.

  I need to set up a permanent conference in MCU?

  I have to configure Permanent Conference as 22228?

  My SIP domain name is vcs.com

  Rgds

  Bobby

  Hi Bobby,.

  on the check of EX90 you added the multisite key. TC5 version wouldn't hurt.

  Do not use a version

  Some generic endpoint support information:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/cisco_telepresence_mcu_configure_multiway_kb_166.shtml

  You can have multiway or multisite, so if you have already configured the EX90 for multiway

  This will be the reason why you can't add another local call, these features are mutually exclusive.

  If you delete the multiway address it should work again with multisite.

  Cordially conf multisite, check on the

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Multiway_Deployment_Guide_X7.PDF

  In short you must enable autocreateing of conferences with no PIN number prompt and have a prefix MCU

  recording, editing of your plant in conference setting, do not overlap with other conferences / MSDS

  Not to mention that I recommend the vcs, mcu and endpoint admin guides http://tandberg.com/docs is a good start

  Bobby, please note the answer with the stars below and set the thread if it's an answer!

• A MultiSITE call may be promoted to a MultiWAY call?

  I have a customer who currently has a number of endpoints with multi-site licenses, mainly 6000MXP units.  The client is developed to the point where 6-pin calls are no longer adequate, and they'll have to buy an MCU.

  My question is:

  Can the customer still enjoy the microcontrollers built in codecs 6000MXP and use a MultiSITE call until the participants are too many and then degenerate into a MultiWAY call?

  Will there be a way to migrate the customer to a MCU usage, perhaps by the personal use of alias of bridge?

  Hi Anthony!

  Can the client still take advantage of the built-in MCUs in the 6000MXP codecs, and use a MultiSITE call until such time as the participants are too many, and then escalate to a MultiWAY call?
  

  No, it is not possible to climb a call running Multisite for a call Multiway or MCU (MXP or C series).

  On the endpoints that will be able to launch the Multiway call is an exclusive setting, therefore,

  Select Multisite, Multiway (or completely disable a Multipoint).

  In addition Multiway must be supported by the endpoint, newest Cisco/Tandberg endpoints points support

  initiate a call Multiway and many (incl. 3rd party) support to be reunited to form a Multiway call.

  It is also dependent on the version of the software.

  In short, with Multiway may as end points that do not support being redirected

  for the MCU (for example the outer parts where you don't have conrtol from software versions,...)

  do not be reunited to form the Conference.

  Is there a better way to migrate the client to the use of an MCU, perhaps through the use of personal bridge aliases?
  

  
  Is there a better way to migrate the client to the use of an MCU, perhaps through the use of personal bridge aliases?
  

  To swap the MXP multisite with a microcontroller of HD Cisco (old Codian) is a great idea in any case, it will not focus only

  the capacity of the largest conferences but also improves quality. Each participant will receive its own optimized

  video stream instead of the single video stream where the worst participant defines what you will get.

  As you said, after meeting personal room numbers (with findme or certain rules of vcs, you can also do named uris,

  as [email protected] / * /), generic virtual meeting rooms or to book through TMS/Scheduler

  may be the solution.

• SX20, MX300 and Cisco C90 multisite functionality

  Hi all

  Someone has information on how to Install Licenses Multisite L-C90-MS, LIC-MX300-MS and MS-SX20-LIC?  These is installed directly in the codec? what procedure?

  Thank you very much!!

  Mario,

  This is the option buttons that you add directly to the codec. Just go to maintenance > upgrade and paste the option key pressed in the key field of the option. This usually requires a restart when completed.

  Adam

• SX20 multisite deployment

  Hello

  I am looking for a design based on SX20 and telepresence SX10 solutiion provide a Multisite videoconferencing.

  The architecture is based on a central site and two remote offices that is linked together via the VPN.

  What are the requirements of hardware video telepresence to provide a multi-site / multi participating solution mixed with softphone SX20, SX10 and Cisco Jabber video?

  Cordially kinds.

  Hello

  SX10, you deploy CUCM or VCS for call control.

  For multisite call, you can use built-in multisite your SX20.

  BR Oleksandr

• Multisite conference

  Hi all

  I have configured the VCS with 3 endpoints SX20, I red that I can make the conference with up to 4 participants.  It told me that I can "bind" these 3 points of termination and to a conference with 12 people, is it true?

  I appreciate your help

  Each breakpoint must have the multisite option installed key.

  If they do, then each breakpoint can connect to 3 additional sites; Car + 3 = 4.

  You can mount cascaded evaluation criteria, however, is not an elegant solution, and it is certainly not enough - say the least. I shudder to think of what it would look like if the evaluation criteria have been defined "Continued Presence", if

  Point final 1 connection to 2, 3, 4

  Point final 2 connection to 5, 6 (+ already connected to 1)

  Point final connection 3 to 8, 9 (+ to1 already connected)

  You can do variations of the above, but no matter how you do it, it will be not very nice.

  Much better solution would be to use a correct MCU, if you do not want to invest in your own, a hosted service would be a very good option.

  /Jens

• SX20 multisite - lose my mind?

  I don't know if I will have a memory loss or what, but doesn't not the SX20 w/multisite supports a total of 4 (1 + 3) video sites and audio-only 1 site?

  CLI I confirmed that my SX20 can do a max of 3 calls (SystemUnit State MaxNumberOfActiveCalls), while the C40 and EX90 can do 4. It also appears that the MX300G2 means a maximum of 3 calls so.

  I swear all MX/SX/C-Series have been able to compose of 3 video sites and audio 1: the site with multisite enabled, with the exception of the SX10.

  I've done a few tests for you here with one of my SX20s (tested with TC7.2.1 and CE8.0.0). Composition performed from the web interface.

  You can only place three video calls - you can not add a 4th participant (wither audio or video - it just does not).

  If you perform the audio call as the first call, you can add then only two video additional participants.

  The value 'MaxNumberOfActiveCalls' on the SX20 is 3.  Even if the data sheet indicates that you should be able to make 4 phone calls to 576 p 30, I was unable to in my tests.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Register of licence multisite on sx20

  Hello

  Please, can you tell if the multisite on sx20 license must register on codec?

  Thanks for your help

  JCA

  Sent by Cisco Support technique iPad App

  According to the data sheet multisite is incorporated into the sx20.

  So I guess that you do not have to add this.

  / Magnus

  Sent by Cisco Support technique iPhone App

• Multisite deployment

  Hello, I need to implement videoconference between sites using multisite (sx10, sx20, dx80 and jabber clients + spa300 ip phone) and I be6ks to this effect, do I need extra MCU in the MRLG or I can use internally sx20 MCU for this and if I use it, it should participate in the Conference in order to make this conference? any help or useful document for this case?

  You can use the internal microcontroller in the SX20, however, it must be in the call that he will host. This means that you can have a maximum of 3 additional sites of the Conference; SX20 + 3 = 4.

  If this is insufficient, Yes, you will need to an MCU, that you are deploying a premise, or use a hosted solution of cloud belongs to you. Depends on the intended use and the economy.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.