SX20 multisite deployment
Hello
I am looking for a design based on SX20 and telepresence SX10 solutiion provide a Multisite videoconferencing.
The architecture is based on a central site and two remote offices that is linked together via the VPN.
What are the requirements of hardware video telepresence to provide a multi-site / multi participating solution mixed with softphone SX20, SX10 and Cisco Jabber video?
Cordially kinds.
Hello
SX10, you deploy CUCM or VCS for call control.
For multisite call, you can use built-in multisite your SX20.
BR Oleksandr
Tags: Cisco Support
Similar Questions
-
Hello, I need to implement videoconference between sites using multisite (sx10, sx20, dx80 and jabber clients + spa300 ip phone) and I be6ks to this effect, do I need extra MCU in the MRLG or I can use internally sx20 MCU for this and if I use it, it should participate in the Conference in order to make this conference? any help or useful document for this case?
You can use the internal microcontroller in the SX20, however, it must be in the call that he will host. This means that you can have a maximum of 3 additional sites of the Conference; SX20 + 3 = 4.
If this is insufficient, Yes, you will need to an MCU, that you are deploying a premise, or use a hosted solution of cloud belongs to you. Depends on the intended use and the economy.
/Jens
Please note the answers and score the questions as "answered" as appropriate.
-
No point endpoint name when SX20 Multisite conference
Hello
I have install a lab which consist of 2 SX20 and 1 EX60. Using SIP and any call control, trying to conference with capacity multisite SX20 (just call using the [email protected] / * /). But, I noticed there is no display name below each participant in the video. Is this a normal behavior? I configured the name displayed on each endpoint.
Yes, this is a normal behavior. The names of the participants will be displayed when you use a microcontroller, and if it is configured to do this.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate. -
SX20 multisite - lose my mind?
I don't know if I will have a memory loss or what, but doesn't not the SX20 w/multisite supports a total of 4 (1 + 3) video sites and audio-only 1 site?
CLI I confirmed that my SX20 can do a max of 3 calls (SystemUnit State MaxNumberOfActiveCalls), while the C40 and EX90 can do 4. It also appears that the MX300G2 means a maximum of 3 calls so.
I swear all MX/SX/C-Series have been able to compose of 3 video sites and audio 1: the site with multisite enabled, with the exception of the SX10.
I've done a few tests for you here with one of my SX20s (tested with TC7.2.1 and CE8.0.0). Composition performed from the web interface.
You can only place three video calls - you can not add a 4th participant (wither audio or video - it just does not).
If you perform the audio call as the first call, you can add then only two video additional participants.
The value 'MaxNumberOfActiveCalls' on the SX20 is 3. Even if the data sheet indicates that you should be able to make 4 phone calls to 576 p 30, I was unable to in my tests.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate. -
Reached the maximum of SX20 codec calls once an audio call is connected?
Hi all
I have different SX20 devices deployed on our corporate network that are currently on the same version of software: TC 7.2.1.
For some strange reason that a device does not have a second call (audio) to be placed and added after it has established the first video call?
Everyone knows this?
In the State of the system it says the MaxNumberOfActiveCalls = 1 where, as my other systems SX20 say MaxNumberOfActiveCalls = 2?
I have attached a picture of the number experienced in the tab "call control".
Thank you
Brad
The SX20 has the Multisite Option? Check under the Home tab.
If no Multisite option installed, adding another call for multipoint call will make the second audio call to become involved only and this is a normal behavior. You mentioned that you cannot add another call (audio), is the system put into service and recorded the CUCM?
Check also under Configuration > System Configuration > conferences what Multipoint mode:
Kind regards
Acevirgil
-
Hello
I want to know the bandwidth consumption when I use it with three other SX10 SX20 Multisite on MPLS (rate set to 512).
Consumption of bandwidth for SX20 is regardless of the total rate of calls for each endpoint that is connected to the Multisite Conference, while each SX10 will consume only what he call rate is fixed.
-
SX20, MX300 and Cisco C90 multisite functionality
Hi all
Someone has information on how to Install Licenses Multisite L-C90-MS, LIC-MX300-MS and MS-SX20-LIC? These is installed directly in the codec? what procedure?
Thank you very much!!
Mario,
This is the option buttons that you add directly to the codec. Just go to maintenance > upgrade and paste the option key pressed in the key field of the option. This usually requires a restart when completed.
Adam
-
Register of licence multisite on sx20
Hello
Please, can you tell if the multisite on sx20 license must register on codec?
Thanks for your help
JCA
Sent by Cisco Support technique iPad App
According to the data sheet multisite is incorporated into the sx20.
So I guess that you do not have to add this.
/ Magnus
Sent by Cisco Support technique iPhone App
-
multisite functionality: SX20 vs C40
Hi all
I get confused on the difference between the SX20 and C40 in terms of multisite functionality.
Is it true that C40 can manage several participants at the same time as the SX20 with the same infrastructure (MCU)?
And then I'm just the high definition SIP/H.323 MultiSite feature four lanes 1080 p 30 means that you can have a total 4 participants (including you) both with the quality of the 1080 p 30? If it is true then it is possible to have more participants with lower video quality?
Thanks in advance.
Best regards,
IJE
There is no difference between SX20 and C40 capabilites multisite; maximum number of participants is 1 + 3 (auto + 3 additional sites). This is so regardless of the resolution, non - you will not be able to increase the number of participants by lowering the resolution.
/Jens
Please evaluate responses and trademark issues "answered" as appropriate.
Sent by Cisco Support technique Android app
-
Hello
I have the (unlicensed multisite) SX20, SX10, DX80 and JABBER for iphone Registred on CUCM and IM & presence,
I tried to make a video call with Jabber, then I added the second participant DX80 with voice only, but when I try to add the third participant SX10 with voice only to the Conference call has failed.
You can't, not without the MS license installed.
The SX20 allows adding an audio call when, in a videoconference to point without the MS license .
It does not allow two audio calls. So, if you connect to video point, you can add an audio call.
If you connect to audio point, you cannot add a second audio-only call. It is a hardware limitation, not software.
/Jens
Please note the answers and mark questions as "answered" as appropriate,
-
SX20 it indicates the maximum number of calls has reached
Hi all
We have a SX20 with a strange issue it only makes a video call and when you try to call another participant, he says 'Max number of calls has reached '.
The State of SystemUnit, we see the following
Software
- ApplicationEndpoint
- MaxAudioCalls2
- MaxVideoCalls1
- Names52010
- Release date2015 01-26
- ReleaseKeytrue
- VersionTC7.3.1.8a4696f
Is possible to change this MaxVideoCalls 1, I try to CLI but I have not found any command.
Concerning
Anestis Koukis
All Cisco codecs are hard coded to allow only 1 video call and another 1 only audio call. Something that cannot be changed. If you need more than 2 connect video calls to a single endpoint, you will need either buy the licence Multisite which allow you to use the bridge internal of the SX20, or use a conference bridge external such as an MCU or telepresence server.
-
Resolution always falls on a multisite call if a Premium license is active?
Hello
Multipurpose codecs, the resolution will drop when a multisite call is established using the multisite aboard hook function. Chip resolution steps for the bottom of endpoints:
Changes of SX20 resolution to 576 p 30
C40 resolution to 576 p 30 changes
Changes of C60 resolution at 720 p 30
C90 changes resolution 1080 p 30
If you apply a Premium resolution license to the codec, the resolution still drop? are they the same? or at least get bumped slightly higher?
If it does not increase the resolution, how does it increases for each model?
Hi Kris,
It will still drop, regardless of PR - key.
Thank you
Marius
-
Presentation of the screen double with SX20
I have two recently installed SX20 units which are registered on a VCS. Both units have the following options installed.
NaturalPresenter
MultiSite
PremiumResolution
DualDisplay
What hosting a three-way one of the units (Site A) call displays a full screen remote part on the monitor of the first and the second remote side full screen on the second monitor. That's how I can expect it to appear. However, the second unit (Site B) shows two parts away on the first screen and displays only the presentations for the second screen that otherwise would be empty. I compared all the parameters and believe that they are the same for both units.
To further complicate the issue when B Site hosts a multisite call or device uses the second screen for video. By selecting the options of the touchscreen controller layout did not involve video displayed on both screens.
The following settings are configured under Advanced Configuration. Video.
Monitors: double
LocalLayoutFamily: automatic
RemoteLayoutFamily: automatic
Any ideas?
What Site a using the on-board microcontroller, welcomes all sites, he will receive a video stream separated from each participants, however, it will be transcoded and it will send a composite stream that contains all the sites of the Conference on other sites - so this behavior is correct.
Looks like that Site B has been configured with video output 'Role to monitor' value 'Format' only instead of "Second".
/Jens
-
Double screen in Cisco Telepresence SX20
Hi all
I have a recently installed SX20 units which are registered on a VCS. the unit has the following options installed.
NaturalPresenter / MultiSite / PremiumResolution / DualDisplay
When I make a call to another site and I m send a content, I´d like to see on the screen on the left side in full screen the remote site.
And on the right screen, I need see what I m sending.
Anyone know how to make this configuration?
You suggest you have a look on the Administrator's guide, choose the one corresponding to the version of software you are using: http://www.cisco.com/c/en/us/support/collaboration-endpoints/telepresence-quick-set-series/products-maintenance-guides-list.html
Go to control panel, category "Vidéo", "monitors:, select 'Dual' or 'DualPresentationOnly'. '. See screenshot below:
Go to the video output and output hdmi 1 and hdmi 2 value what configuration you need. monitor i.e. first, second, presentation only, see the screenshot below:
.
/Jens
Please note the answers and score the questions as "answered" as appropriate.
-
"No video in" error when connecting two SX20! Help, please
Hello everyone
We have problems to connect our two SX20 telepresence equipment, which has a bridge. When you call one SX20 on the other, once the connection is established, the message "no video in" appears on the screen. How to solve this problem?
Also, we want to call the SX20 of jabber accounts video from computers and vice versa. How can do us?
Currently, we only connect the two SX20.
This is the deployment, we want to have.
Thanks in advance
In most cases no video is caused by firewalls and other devices with a logic of layer-3.
You also had a different thread open material a generic question of deployment.
Maybe you have a cisco partner or an external consultant who can help you with that.
As you also said mobile devices, if a 3rd party there is always a chance that
devices do not understand well the other on road signs or the face of the media.
But at least two sx20 should be able wiith all problems to send and receive video
If deployed stand alone or with a call like vcs or cucm control.
Which brings back once again, check the network ;-)
Please remember useful frequency responses and identify useful or correct answers.
Maybe you are looking for
-
I use Firefox as my browser, and usually, it opens with google as homepage, and searches are via google. It suddenly started opening on yahoo and also use it as a search engine. I suspect that it happened when I downloaded the update for C Cleaner, w
-
CQ57-339wm driver does not work
I work with someone who has a CQ57-339WM (serial 5CB2050K51, product QE264UA) that is out of warranty and had a faulty hard drive. They do not have to burn recovery discs. I reinstalled Win 7 Home, installed the current ethernet driver, made all the
-
Satellite C650D - resettlement is stuck
Hello I have a Satellite C650D, who became very slow, so I decided to do a clean install. Everything seemed to go well and it restarted and then he inquires finishing installation. He proceed to install 40, which went well. It seems then automaticall
-
I want to start making videos and do not know which version is the best for my system and my novice status?
-
Why can't I activate windows since my license for Vista Home Basic is valid?
I am licensed by live-time for windows Vista Home Basic, but it tells me that I can't activate windows and need a new license;