NEITHER 9213 changing high resolution at high speed. Screenshots included.

Similar Questions

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• WiFi unstable and slow Internet high speed

  Hello world:

  Recently, I am facing a problem of unstable wifi, slow speed of the internet of my macbook pro. I hope someone could help me with my problem.

  
  

  Symptom:

  Internet mainly speed just unstable using a wifi connection. (no problem with wifi connection self and my wifi suddenly grave would not be)

  Example:

  • FaceTime with my friends and the connection would suddenly abandon or images & audio gets fuzzy.
  • Videos in online streaming and suddenly occurs buffering.
  • Download file of software update iPhone via iTunes, the speed is slow, he needed to take 2 h at the end and later on a window display "cannot download and check your internet connection".
  • Suddenly cannot open websites like site apple.com, google.com. Sometimes it will take more time to open Web sites.

  Hardware and software:

  MacBook Pro mid-2009, OS X EL Capitan 10.11.5

  ISP: Cox, 50Mbps

  Modem & router: Netgear N450

  Test:

  Turn off my wifi and connect my macbook pro with modem & router with cable, internet high speed is stable and fast. Internet speed download speed test result display is of around 60Mbps, download speed is around 8Mbps. And I tried streaming using the connection cable, there was no buffering.

  I already tried the possible Solutions:

  • Restart the Macbook pro and restart Modem & router: will not work. I mean the internet will be very well at first, but later would be unstable again.
  • Reset Wireless Modem & router and change channels: useful, but not completely solve the problem. After you change the wireless channel, I tested my internet speed and the result showing 20-40Mbps (slower than 60mbps) speed download. Sometimes, the result will be like 6-8Mbps and sometimes it will be 60Mbps. If its unstable.
  • Wireless diagnosis: result indicates connection is good.
  • Called my ISP provider: they checked and said all right.

  
  

  Other Questions & details:

  • The internet is ok for most of the time. But when all of a sudden I can't open site or I can't download and streaming & FaceTime at normal speed, his frustration.
  • I thought it might be related to my hardware since its an old macbook pro. I can't run Apple hardware test because I don't have the installation disc more and my macbook pro is very old. Is it a third party software that can perform the test hardware on mac?
  • My wifi used to be very stable and I don't have to worry. Just for these last two weeks.

  
  

  
  

  I really appreciate your time and help! Looking forward to any reply!

  Wi - FI connection drops

  Connection Wi - Fi in OS X Yosemite problems

  Wi - Fi in OS X Yosemite connection problems (2)

  Connection Wi - Fi in OS X Yosemite problems (3)

  WiFi potential temporary fix - Yosemite

  Also try turning off Bluetooth.

  WIFI AND BLUETOOTH FINALLY SOLVED, NOT REALLY - YOSEMITE 10.10

  If your Wi - Fi source is capable of generating a 5 GHz Wi - Fi network, try that in order to avoid conflicts with Bluetooth.

• S50 satellite - B 15 P - Fans running at high speed and system crash

  Hello

  I have a new SATELLITE S50 - B 15, i7-5500U, 8 GB Ram, SSD etc., IV and v have some problems with it.

  for unknown reasons the CPU fan starts to operate at high speed, even if the temperature of the CPU hit is not 35%.
  It also froze about 10 times since I got it (April this year).

  The only way to make it work again would be me to hold the power button down until stop and start it back up.
  Once launched upward there is no mention of potential problems in the newspapers of events other than the forced closure.

  I just wanted to know if anyone else has experienced problems?

  Thank you

  Chris

  The only way to make it work again would be me to hold the power button down until stop and start it back up.

  Forcing order restores the fan activity and performance?
  Hmm it sounds like there must be some sort of system emits probably the bottom of some process locks the CPU and therefore increases the activity of the fan.

  You could start the the Task Manager and in the process tab, you will find all background applications that would appeal to the CPU.
  Click the CPU column to display all the processes of loading the CPU.

  However, you can also try to change the option of cooling method that is available in Windows Advanced Power options.
  Go to control panel → power options.
  Click here on the power plan that is currently in use.
  Then click on advanced power options and access the cooling method.
  Here you can change it from active to passive.

  

  In addition, you can decrease the status of CPU max at 90-05%

  

• Toshiba high speed Port Replicator III - use of 2 x 4 k monitors on 60 Hz

  Dear Toshiba support.

  Is it possible to run 2 x 4 monitors k on 60 Hz on the Port Replicator Port Hi-speed Toshiba III (dockingsation)?
  He says he has Display port 1.3 (supports 4 k monitor the 60 Hz.) and a 2.0 HDMI (which also supports monitor k 4 on 60 Hz.).

  With sincere friendships.
  Augurkie

  PauPau wrote in this thread on the high speed Port Replicator III
  https://Forum.Toshiba.EU/showthread.php?83052

  DisplayPort supports the following resolutions:

  Resolution - Refresh Rate (HZ)
  640 x 480 - 60,72,75,85
  720 x 480-85
  800 x 600 - 56,60,72,75,85
  848 x 480-60
  1024 x 768 - 60,70,75,85
  1152 x 864-75
  1280 x 720 - 50,60
  1280 x 768 - 60,75,85
  1280 x 800-60
  1280 x 960 - 60,85
  1280 x 1024 - 60,75,85
  1360 x 768-60
  1366 x 768-60
  1400 x 1050 - 60,75
  1440 x 900 - 60,75,85
  1600 x 1200-60
  1680 x 1050-60
  1920 x 1080 - 24,25,30,50,60
  1920 x 1200-60
  2560 x 1600-60
  3200 x 2000-60

  But it seems the resolution also depends on the GPU built in the notebook

• Portage Z30-A-13W connected to the high speed Port Replicator III - USB problems

  Hi all.

  We recently bought a new Portage Z30-A-13W and Hi-Speed Port Replicator III.
  Setting network and graphics work correctly with port replicator, but the USB ports don't work at all.

  I tried the port replicator USB 2.0 and USB 3.0 and I can't seem to work with a keyboard, mouse, USB key or a mobile phone.

  In the case of mobile phones, it is also no output power of the ports that the mobile does not start to load.

  At any one another experianced this problem and what was the resolution.

  Thank you very much

  Jonathan Davies

  Hello

  As far as I know additional drivers are not really needed to use the USB ports.
  This is why I m wondering why don t USB ports work.

  It might be possible that ports high speed Port Replicator III USB are faulty, but to be honest, I can't imagine that all 6 USB ports may bad work at the same time.

  So maybe it s a software problem.
  First of all, I would recommend the default BIOS and check the USB legacy support for keyboard and mouse could be activated.
  After access to the Device Manager and remove / delete the USB hubs and controllers in the list of devices.

  Keep high speed Port Replicator III connected to the computer and restart the device.
  Usually, the system should recognize automatically deleted USB ports and must update the drivers of USB ports.

  I hope that the USB ports don't work after this short workaround solution.
  Keep your fingers crossed.

• Portege 3480CT lack always high-speed mode frequency

  One of my 3480CT Portege lacks always high speed frequency mode, but it has.

  I couldn't find the setting always high since there were only two options available for the power setting in F1 that are still weak and dynamically switchable only menu.

  Hello

  Sorry, but I don't understand your problem. Can you please specify more? As far as I know if you want to change different profile you must use the FN + F2 key combination.

  You can make individual settings for each mode in standby electricity by clicking details.

• Tecra S11 - CPU fan is high speed

  Hello

  We have a problem with nine Tecra S11 / Windows 7 64-bit. The CPU fan is noisy high speed during ignition and start Windows. No change after logon. Speed remains unchanged up to go to the sleep mode once. After waking up, everything is OK.

  For me, it seems to be a problem with the firmware (BIOS). Update V1.70 but no change. We have same problem with the S11.

  Any ideas?

  Cordially Stevep

  Hi Stevep_1,

  Have you tested different cooling options in Windows power management? Check it for each profile, and then select battery optimized cooling.

  It work?

• HP Compaq DC7800p Convertible: Fan never works at high speed

  Well Hello hp. My question is that I have the hp compaq dc7800p with intel q35 chipset. I also have the intel core 2 duo e6750, who comes to 66 without high-speed fan spining. I checked, the site of intel, that it is said that Tcase is 72 C I also have the problem with the chipset, there too big temperatures when you play. It goes up to 80 C. What I would do. Should I change cpu fan or don't start high speed at 70 ° C and for the chipset how cool up to at least 60 C, I have the normal aluminum without cooler chipset. I play the games are battlefield 3 and 4 and yesterday my pc freezes, and when I rebooted funs went at full speed, but nothing showed on the screen for 5 minutes, is now well, fortunately, but I all wory to much.

  Temperatures look ok so far.

  -In addition to being very energy efficient - Core2Duo processors have built-in thermal protection.

  If ever they come to high temperature, the frequency is decreased. If temperatures reach critical CPU turns off.

  Chipsets get usually a little hot under load.

  80 ° C is still about 25 degrees below criticism.

  What graphics card you have?

  As far as I know, feeding in these machines has only about 360 watts, which is not enough for some high power graphics cards. It is most likely the reason why your PC freezes. Video games cards consume not only a few watts, they also generate a huge amount of heat under load.

  Anyway, there are two things you can do:

  First, go to the HP Support and get the dc 7800 manual.

  Uninstall the CPU cooler and apply new thermal paste (don't forget to clean the old one).

  Then, increase the speed of the fan slowed down in BIOS F10 for better air circulation.

• Re: Satellite C55-A-1JL - the fan spins at high speed after updating BIOS

  Hello

  I've upgraded the BIOS of 1.20 to 1.40 and my computer started to automatically restart after a few minutes. the fan continues to run at high speed all the time

  Someone knows why?

  Question: the laptop work properly not to mention that the fan is rotating fast?

  Generally after updating the BIOS you must always load the BIOS default settings.
  In the BIOS, press F9 (load by default), and then press F10 to save the changes.

  Try it

• Lenovo Z500 fan only runs on high speed

  Hello.

  Recently, I removed the lid of my laptop to clean my fan and to change the thermal paste on the proc and video. But when I replaced everything back and booted up the laptop, my fan only works on speed continuously. No rattling, it works just like my proc is very responsible, but no hot wind, cold. I checked the temperature in the Speedfan program and everything seems to be ok, but I noticed that there is no fan detected. Same thing, I saw in Everest. I tried to watch BIOS, but there is nothing in the fan or temperature associated (I change my bios there is a moment so my F1 - F12 keys would swap with FN keys). And also, in the management of energy, I tried to remove the dust, but just ran fan as it removes dust every time, none of the changes, same high speed. I tried Driver Pack Solution, no results on the fan. Everything went very well before I cleaned it, I was just trying to make my computer train less.

  Please help me, thanks in advance.

  Alright, removed the lid once more and discovered that the fan wires melted because of the heat the tubes that will proc and the video, so the wire that controls the speed of the fan has been disconnected. Anyway, case closed, just need a new fan, will not appear anywhere it's for sale, but that is another issue for another day.

• High-speed FPGA personality my Rio

  Hello

  I started on a Rio My 1900 I am programmer in C language so without by Ferryman Labview.

  I wish I could sample a signal to a frequency higher than those possible with the standard personality FPGA provided. The doc of the RIO my dt requires high-speed FPGA personality it takes to download the site of NI I therefore downloaded but son installation requires labview 2014...

  How can I do?

  Thanks in advance for your help.

  Françoise

  Hello

  To change the FPGA, USE of it requires LabVIEW and FPGA module. You can only use the default personality pour en C development.

  Kind regards

• Problems initializing digitizer card high speed

  I recently built a new computer for data acquisition.  I had all the questions according to a program for the acquisition of data for a digitizer high speed written in LabWindows 8.5 and it works successfully with LabWindows 9.0 on the new machine.  The only problem I encountered was name the digitizer card high speed max the appropriate name of the resource planned by the data acquisition program.  Everything went very well for 4 days.  Today, I try to run the same program and cannot enforce.  Debug code indicates that the device fails to initialize when niScope_init() is called.

  In MAX passes card scanner that can call a test and I have test panels and see an input signal.  I checked the name of the device to ensure that it matches the named resource that provides the program.  I also reset the device to the MAX and then tried to run the program.  None of these attempts succeeded.

  I can't really find anything that changed between the last time I ran the program and today.  Everybody to face this problem in the past, and is at - it solution or a proposed additional troubleshooting?

  This problem has been resolved by reinstalling the drivers for our digitizer high speed.  I have still no idea why after four days, something happened to the original driver installation.

• Generate a single pulse on several channels of an external trigger high-speed DIO

  Hello

  I'm trying to implement a system using a PCIe-6535 b connected to a high speed of SMB-2163 DIO.  The system must be configured to work with a camera send a trigger (at the beginning of each show) to the PFI4 which in turn sends a single pulse on three digital output channels to lasers.  Each output has its own specific deadline and the width.  There is no counter on the SMB-2163, so I think I need to use Pulse Width Modulation (PWM).  I saw this example and adapted to my system:

  https://decibel.NI.com/content/docs/doc-8010

  However, when the source to enter the DAQmx VI of sample clock is set to PFI4 (instead of the on-board clock) to receive input from the camera, changes in behaviour.  The rate of sampling in the sample clock VI is ignored, and each element of the digital waveform is triggered.  I need the sequence to complete each after trigger.

  I am attaching a quick diagram of the sequence.  Any suggestions on how I can get this kind of events triggered? (With the help of LabVIEW 2013)

  Thank you

  Mike

  PLATES

  

  

  The external signal must be configured as a trigger for digital startup rather than the sample clock.  I do not think the 6535 redeclenchables supports digital output, so you don't have to restart the task after receipt of each trigger (something like this, however you can improve performance by committing to the task by using the task of control DAQmx before entering the loop).

  Best regards

• High speed continuous measurement of encoder with sampling frequency of 1 kHz

  I am able at all times the position of a linear encoder using a PCI-6602 counter card, and I need to know how to set up so that the counter rotating at high speed, but the data is inserted into the buffer at a frequency of 1 kHz.  I am able suddenly to a hydraulic cylinder, and I am not concerned about the event recording to high frequency except to the extent where they throw off the number considerably if the equipment does not run fast enough to detect all the impulses of the encoder.

  Now, I think is that the external sample clock signal control (routed internal pulse output counter) time rate whereby the equipment detects the impulses of the encoder and the rate at which it inserts data into the buffer.  With a pulse 100 per inch encoder and a sampling frequency of 1 kHz, the extended final position of the cylinder is turned off by +/-0.15 inches, which is unacceptable.

  I need calculate a speed of this information, so I prefer not to use software timed sampling to control this (it's more difficult programming for other reasons as well - several asynchronous measures).  Any ideas on how to configure the hardware to count faster than the speed at which she inserts counties in the buffer?

  OK, you're clearly on the right track here, so I will focus on some details.

  1. How do you know that the +/-0.15 "differences are * measurement error rather than * error of movement?  Why wouldn't be an accurate measure and a proposal which can vary slightly from the nominal value?

  2. I wonder some all electric noise and defects that may produce false edges.  The fact that the behavior was better by using a sampling rate limited (200 kHz) in the digital inputs may be that some of these flaws were so short that they were never captured.

  I did a ton of work with the Commission to 6602 encoder and I can certainly confirm that count equipment is sensitive to the edges in a few tens of MHz.  (I know its 80 MHz for edge counting, but I think I remember that it can be of the order of 20 to 40 MHz to accommodate the time of signal propagation extra of the quadrature decoding circuit).

  A small point of clarification.  You're talking about the speed at which the meter "works to.  The value of count is a register whose value is changed completely by the circuit, * independent * of the sampling frequency.  If you enjoy with material-clocked County in memory buffer or interrogation of software without buffer not a bit for circuits that increments / decrements the value of the counter register.  (In other words, I am completely convinced that you would get commensurate with position end even if you took only 1 sample software-polled after the end of the move instead of sampling at 1 kHz all the way through.)

  So, if the value of the counter is disabled, it is because the circuit detects producers of County of the edges that shouldn't be there.  Something you can try is to set up digital debounce filter for input lines of the PFI corresponding to the encoder Source inputs and to the.

  -Kevin P.