Network names

Similar Questions

• Change network name

  When I change the name of the network should I reconfigure all printers on the network?

  Potentially, Yes. If your printers are wireless, then you will need to reconfigure with new wireless network name to connect.

• HP Pavilion M4-1002TX: network name not displayed in my HP pavilion m4-1002TX

  Hi you

  Really need your help. My lappy since there are 2 weeks unable to connect on behalf of the office network. The name of the network is invisible. Connection are available but not connected. I tried all the HP PC, troubleshooting wireless network and internet in vain.

  I have no idea right now. Some laptop HP with the same model at the office have a same problem.

  Other network name are appear in the list & also can direct connect using the usb cable.

  Please help me.

  OK after the reset of the modem the network name does not always show upward?

• How to change network name on Time Capsule

  Hello

  I want to change the name of the network on my Time Capsule, to match that of my home, all other routers network so I can use it as an access point more easily.

  How should I do it under OSX?

  Thank you.

  Open Airport utility, click on the Time Capsule icon, then click on modify in the window pop up.  Then go to the wireless tab, network name can be changed here.

• Printer wireless network name recognition

  I have an all-in-One of C4795 printer, on Vista 64-bit, which can not connect again ATT Uverse router. The router has been replaced and printer identifies the old network name/number. I tried everything the HP web site offers, but nothing worksI. At some point in the implementation I find the new name/number and I printed the report of NetworkTest wireless and it shows the old name/number. Help! Joe C.

  Hi Joey1969,
  
  Follow these steps in the document below. Let me know if you need help.
  
  http://goo.GL/jXYCw

• Network Name (SSID) Found failed is the message that I received after the test run. Cannot access my printer.

  I can't print my coupons to my email... ran a test and it say network name (SSID found) fail... but it says that the printer is ready and online?

  Hello

  1. don't you make changes to your computer before the problem?
  2. what operating system is installed on your computer?

  Please follow the steps in this link:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/wireless-printer-goes-offline-with-a-message/d83e6dcd-AF35-4e55-9516-47944e70a125

• NET USE error: '67 system error has occurred. The network name cannot be found. »

  Original title: NET USE worked for error.

  OK I used the following with a RDP'ing of XP in a server of S2k3 years:

  NET use lpt2 \\SERVERNAME\printername /persiternt:yes

  now, I get a "system error 67has has occurred. The network name cannot be found. »

  What made me state was I restarted my XP machine.

  What I've done since then rebooted the box of the network, hubs, Wireless DSL modem router and the win 2 k 3 boxes with the same results...

  suggestions?

  Hey cvs334, would you unplug the ethernet cable from all these devices ' network box, hubs, Wireless DSL modem router and the win 2 k 3 boxes "then unplug the power cord for each. Then after about 60 seconds, connect waiting for DSL modem for sink power cord. Then plug the router after sink connect the router to the modem, and then connect the hub and other devices. This allows the automatic redirection Web DNS router to the modem. The router may be failing or the router LAN port may be faulty.

• Could someone tell me that I have a laptop that is compatible with the adapter wireless Athreos in it and it catches an unsecured, network shown as next (automatic) for the SSID (network name). Please tell me how to connect...

  Could someone tell me that I have a laptop that is compatible with the adapter wireless Athreos in it and it catches an unsecured, network shown as next (automatic) for the SSID (network name). I tried parameter as point of access, AD-hoc, Connect automatticaly etc but will not connect... Please tell me how to connect...

  Hi Sumit and thanks for posting.

  Your Athreos has never connected? If it has connected then it not only connects it to insecure networks? Also after can trying to connect you do the following?

  Start, run, CMD, OK to open a command prompt:

  Type the following command:

  IPCONFIG/ALL

  [Note that there is no space between the oblique and ALL bar].

  Right click in the command window and choose Select all, and then press ENTER.
  Paste the results in a message here.

  I hope this helps. After the back if you have any questions.

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Laptop WiFi problem, «identifying...» (network name) ».

  Hello
  I'm having a problem with the wireless on my laptop. Its a HP Pavilion dv6000 and just under a year of age. I had no problems with the wireless until recently. I use the laptop at home and usually the internet is very well (apart from the occasional disconnection), but when I'm at school do frequently connect to the school network (I am a student of the University, and there are several routers throughout the school and in the many buildings). Sometimes it will connect in one building and I'll switch to another and it does not connect. Each time, he does not connect it always says "identifier...". (wireless network name) ». No amount of repair, restart or reset the network card it won't connect. The strange thing is that sometimes it connects to the router in this building (i.e. library) and sometimes it won't. Whenever I have check the status shows that the laptop is received but does not send do not.

  Help! This problem is really starting to annoy me and I don't want to end up throwing my laptop on the whole of the library.

  Hello

  1st brand one Restore Point so that you can return back if necessary (it shouldn't be though).

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  --------------------------------------------------------------------------

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Do another restore Point then you can go back to where you were if necessary with new active pilots.

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  I would like to delete ALL networks, so you can restore if necessary.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Remove the old cable network name machine Vista

  I have 4 computers on a home network (2 portable wireless, Windows 7 and Vista) and 2 desktops (also Windows 7-Vista) to Windows 7 computers, replacing Vista computers in the near future.  Until them, I always use the four computers.

  I had a LOT of problems (unable to access printers and printers go offline) sharing printer and recently started having "Windows cannot access \\theWindows7newdesktopcomputer", those with printers attached - and I could / can not find a solution for this.  In desperation, I have reset the Linksys router e2500 manufactured back State initial and in the process gained a new network name (do not change).

  My problem is that the old Vista computer wired to the router insists on the use of the old network name (the one that appears on the screen of the network and sharing Center).  The funny thing is that I put on Jack autour with him (nothing has changed on the router) I have now access to the Internet on the old Vista computer wired to the router, even if she seems to be using the former name of network.  So, how can I get the Vista computer to recognize the new network name and quit using the former name of network.  I spent all day on this problem and I am not farther than I was when I started working on the problem of this morning on the printer share.  I guess that the router works because these two computers are connected to the router, but it doesn't look good for me and it seems that it must be something I can change or correct.

  Ron in round rock

  Try to remove from the network and sharing Center by clicking on the Home icon next to network name and go to mergere or delete network locations. I guess you know what to do after that.

  If it is used, then unplug your ethernet cable and try again.

• change the network name on my wireless router?

  A few months ago, I bought my linksys router and did the installation of all the stuff that day, including changing the name of the default network. I want to change the name to something different, but when I went to the address of the facility, there was no box to put the new network name [I was on standard wireless settings tab in the wireless section]. Help please?

  [Yay that worked, thank you:]

• 1217nfw MFP how to change network name and password when you buy a new routers

  I have a 1217nfw MFP.  It was working fine without thread.  Then my router has stopped working properly.  I bought a new router and easily set up my computer, the iPad and the iPhone to work with her.  But I don't know how to change the printer set up so that he will see and connect to the new router (i.e., change the network name and the password that the printer uses to connect).  Someone knows how to do this without having to uninstall and reinstall the printer as if it was fresh out of the box?  Thanks for your help.

  Thanks a lot for your help.  The choice to click on my laptop were not quite the same as stated in the article, but the article got to the right spot and I was able to figure out the rest.  So now my laptop is wireless printing.  MacBook Air my wife still does not work, but I'll play with it after the holiday weekend.  Do you know of an article that allows to change the name of the router and the password when it is a Mac?  Whatever it is, thank you very much for your quick response and help.

• vWorkspace 8.0 | HyperV 2012 R2 | < Unspecified > virtual network name

  At a customer's, we went just all HyperV server to HyperV 2012R2.

  Now, we have a problem that the "said virtual network name '.

  Is this a known issue?

  Import does not work in my case.

  To work around the problem we have already defined the network name in the settings manually, but it's always a strange question.

  feature or bug what is the difference ;)

• How to remove or delete profiles redundant network (names) of my office and laptops running Windows 7?

  With Verizon DSL modem in bridge and as a router Linksys WRT 160N, my desktop and laptop computers have been in a network.  Laptop computer and printer via wireless and desktop wired.  The name of the network used to be the same for all connected devices.  However, when my Linksys gave the soul about a week ago, I reconnected it via the Verizon Actiontec WRT704G modem/router combination and since I could not print from the laptop, and it takes about 5 minutes to print 2 pages of my office.  The network name on my desktop by default automatically to the network 4, and on the laptop, there '2' after the former name of network.  With different network names, I couldn't set up my home group.  But I have access to the internet on both computers.  The network name (SSID) on the site config the router and the printer is the same: the former name of the network without the '2'.

  I need help or advice on how to clear or remove these other network names and have just 1 network name for all connected devices.  I know that in Vista, you can merge or remove network profiles but can't seem to find a way to do this under Windows 7.  Also, my laptop is Windows 7 Home Premium 32 bit and the Office on Home Premiun 64 bit.

  Thank you
  Pejuson

  Hi pejuson,

  To remove profiles redundant network from your computer, you can follow the steps mentioned below and check.

  1. open manage wireless networks by clicking the Start button, then Control Panel. In the search box, type Wireless, and then click manage wireless networks.

  2 right-click the network profile you want to change, and then click on Properties.

  3 make the desired changes, then click on OK.

  For more information, see create or modify network profiles.

  Hope this information helps you.

  Concerning

  Arona - Microsoft technical support engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• RSAC can't disable remote Firewall errors "could not access ServerName, the network name cannot be found.

  I opted for the "Restore default settings" option in the firewall while working on a client-side computer. For this reason got disabled the option "remote share' and now I can't access the machine remotely. The machine (which is not in the same network) does not monitor or keyboard attached to her and her to a different location so I can't physically connect you and activate this option.

  I tried to disable the firewall remotely, but the following command does not work.
  PsExec \\hostname u user_name password cmd.exe Pei

  It returns the following:

  Could not access ServerName

  The network name cannot be found

  Make sure you share the default admin$ is enable ServerName

  This fact has not resolved the question above.

  HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindowsCurrentVersionPoliciesSystem\\\ and create or edit a REG_DWORD LocalAccountTokenFilterPolicy value and set the value to 1

  Help, please.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking%2Cw7itprovirt&filter=AllTypes&sort=lastpostdesc

  Hope this information is useful.