no connection after answering sliding cover

Similar Questions

• Problem with wireless connection after the automatic update of Service Pack 2

  Do not see my wireless modem to connect after that Windows Vista Service pack 2 and the update of security were auto-mis to update last night.  Can see modems of neighbors but not mine.

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for Windows Vista Service Pack 2 (SP2) is valid until November 26, 2009. Availability of support chat or messaging differs depending on your location. Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack).

  Or transfer your question in this forum: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Why do I have to restart my internet wireless connection after restart of Windows Vista?

  why I have to restart my internet wireless connection after restart Vista

  Hello

  Second time to answer that line however initially seems to have disappeared. The message displayed
  upward in my Threads as if there was a response.

  -----------------------------------------------------------------------------------------------------------------------------------

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• I can't view the network connection after downgrade from Windows Vista business to Windows XP Professional.

  How can I view network connections after downgrade from Windows Vista business to Windows XP Professional. I have problems to install the drivers of my HP dc7800.

  Click Start > my network places > view network connections in the left pane.

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• Recovery WIFI connection after sleep mode activation takes much too long

  This question of provenance in this thread: http://answers.microsoft.com/thread/b7916ba7-3e34-4ee2-a6e7-bba2fa65508b (title: "HELP!") Driver issue Microsoft Virtual Wifi Miniport Adapter (error code 31)").

  Basically, the presented solution it works for me too. However, the command "netsh wlan set hostednetwork mode = ban" does not get persistent, thereby affecting

  "stop wlan netsh hostednetwork" gets persisted, however.

  'do not command netsh wlan set hostednetwork mode = allow' does not get persistent...

  In other words, current enforcement in exactly ONE time orders-Admin-helps prompt - as soon as I wake my machine to sleep after running it, the WIFI connection gets restored quickly (less than 5 seconds); but when I check the status with "netsh wlan show hostednetwork", then the result is that the mode is set to "Authorized" again - and that means, the next time that I wake up the machine, it takes ages to new (~ 30-50 seconds) before connections WLAN gets implemented...

  Does anyone know how I can get the mode = do not allow to persist?

  Another fact interesting, that I found before I was running on the solution by using the NETSH commands:

  If I change the ' password on the reactivation of the "option of energy saving"require a password (recommended)"to"Don't require a password", it's okay, about the period of time it takes to establish the WIFI connection after wakeup (in other words, even without the NETSH commands described in this thread).

  So, from my point of view, it seems to be that something related to security (probably in association with this kind of things hosted network).

  The problem: disabling of "Protection of password on wakeup" is not a solution to everything, for me personally, as I am quite often on the road with my laptop, and I want to be sure that the data on my laptop is not accessible without unlocking the screen, in the case where the unit would get stolen or I loose it somehow... to protect all customer and other data sensitive data to this topic...

  Any professional entry of someone at Microsoft to finally have a solution for this would be greatly appreciated.

  My hardware: Sony VAIO VPCSB3X9E/B

  See you soon,.

  Franz

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the TechNet Forums. Please post your question in the TechNet forum.

  http://social.technet.Microsoft.com/search/en-us?query=wireless%20networking&AC=1

• Pouvez individual emails to group TB that are connected through answers?

  Is there a setting for the connection or group individual email who is a connected through answers. Outlook (used to work) has this feature and I really like it. Any new e-mail associated with the original is added to the title of the original, by eliminating a long list of separate emails over the place.

  View menu > sort by > threaded

• Photosmart HP 7520: All wireless network devices will lose connectivity after printing

  Dear all, 
  
      I have a problem with my HP Photosmart 7520 printer where all wireless network devices will lose connectivity after a printer has been sent to the printer.
  
  * Summary
  Wireless network unusable after sending one print to HP printer
  No device ( computers nor smartphones ) can use the Internet nor access internal networks ( 192.168.0/24)
  
  * Details
  Turn HP printer on.  ( wireless direct is off - never turned on )
  HP printer connects to working wireless network.
  Other devices ( phone/computers ) already connected and working.
  From any device, send a document to the printer.
  Printer prints document successfully.
  Immediately after printer has printed all devices cannot access internet IP range ( including HP printer ) nor Internet nor router ( 198.168.0.1 ).
  
  * Reproducibility
  Always
  
  * Work around
  Disconnect all devices from the network.
  Power off printer.
  Reboot Internet router.
  
  * Attempted solutions
  Removed wireless configuration.
  Factory reset.
  Added wireless configuration back.
  Powered on and off printer.
  
  * Printing tested with
  Tested with Macbook10.11/Windows 8/Ubuntu 12/Android 4.4.2
  
  * Not tested
  Ethernet cable directly connected to router.
  
  * Internet Router
  Netgear CG 3700
  

  Number of brand and model of the router?

  These settings are to set up your printer wireless (or wired):

  • Stay connected to your router
  • Trouble printer status 'offline '.
  • Wake mode 'sleep'
  • All wireless devices stay better connected

  While the DHCP is convenient, devices like printers (wired and wireless) should always be assigned a (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the range of the router DHCP.  After the adjustment of the static IP address the computer must be updated to show a Standard TCP/IP port with the IP address of printers under printer properties/Ports.

  1. Set a static in the printer IP address (click here) outside the range of the DHCP of the router (check your manual). It is for Linksys routers, but can be used for all routers. Check your DHCP range and change this first if necessary. More Help Wireless Printing is here and here and still more here.  Video here explains the problem and how to solve the problem. <--> So watch this!
  2. Or check in the printer "Auto Off/sleep/Energy Saving Mode" is disabled the System Mode Time Out is set to zero (0) Use the built-in webserver (EWS) by visiting the printer address IP address in the address bar of your browser, click on settings tab/Auto Off. Or use the printer, printer Home Page (EWS) Wizard. Also check your printer properties.
  3. If the printer supports and has IPv6 enabled, disable the IPv6 option in the printer.
  4. Make sure that the printer is connected directly to a socket wall and not to a UPS, power strip or a lightning arrestor. This will cause the printer to drop offline connection and disconnection (checked yes!).

  Additional measures to take if you continue to have the problem (if they are posted)...

• My laptop lost wireless connection after hibernation I or stop it. Then I have to reset the automatic Wireless Configuration to find my wireless connection

  I just bought a new NetGear wireless router and now my laptop lost wireless connection after hibernation I or stop it.  Then I have to reset the automatic Wireless Configuration to find my wireless connection.  Whenever I stopped him it and I have to choose.  This does not happen on another laptop or desktop that I have.  Is there a safe solution for this?

  Hi Ron,

  1 Windows operating system you are using?

  2. you receive messages or error codes?

  You can read the following article and check.

  Windows wireless and wired network connection problems

  If you use Windows XP, then read the following article:

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  This problem can also occur when the power management profile turns off your network card.

  You can try the following steps and check if it helps.

  a. click Start, type device manager in start search and press ENTER.

  (b) in Device Manager, expand network adapter.

  c. now you will see your network adapter or adapters if you have more than one. Right-click on the network component, and then click Properties.

  d. go to the power management tab.

  e. ensure that all check boxes are unchecked (check boxallow the computer to turn off this device to save power is off).

  f. If you have disabled the boxes, click ok and restart your system. Put the computer in Hibernate mode and check if you still have any questions.

• How to get wifi connection after reinstalling factory default DVD for Iconia W3-810?

  My W3-810 Iconia has been reset using Acer Recovery DVD. After that 8 window has been restarted, he not been able to find the wireless device.

  Does anyone know how to get a wifi connection after reinstalling factory default DVD?

  Best is to download the drivers for a different machine, then transfer to the W3 with a USB or SD card. Once they are installed included you be back running.

• Without LAN connection after logon applied credentils it takes a lot of time to load items on the desktop

  Original title: startup problem

  during the priming of the laptop without LAN connection after logon credentils applied it takes a long time to load the items on the desktop, but by connecting the laptop with LAN a boot of the computer LAPTOP, all right, please provide a solution for this problem of starting.

  Hello

  I removed IE 8, now it works fine

• network drive mapped 2003 server need stay connected after journal so that when my script is scheduled to run the player will always be mapped.

  2003 network drive server need mapped stay connected after journal so that when my script is scheduled to run the player will always map. ??

  Hello Scott,

  This is not the right forum for issues with Windows Server 2003.
  Please click the link below to ask your question in the appropriate forum TechNet.
  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

  Thank you

  Marilyn

• Cannot connect after withdrawal of a domain.

  Disjoint my domain to work and now it does not have one of my passwords to connect. Nobody here knows the identifier of the administrator because I was hired just to be the administrator. Where should I go from here? Is it possible to get around the login screen?

  Here is the solution to this problem from Microsoft:

  "You can not connect after you remove the computer from the domain.

  <>http://support.Microsoft.com/kb/317049 >

  HTH,
  JW

• I lost the internet connection after acceptance of your latest updates. How can I cancel the updates?

  I lost the internet connection after acceptance of your latest updates. How can I cancel the updates?

  Debbie

  How do you know that the loss of your internet connection has nothing to do with the Windows updates? You must find the reason for the loss of the connection.

  How do you connect? Is a wired or wireless with a modem or a router? If a router is the router shared with another computer and this computer can connect to the internet? You need to determine if the problem is a fault on your computer or a failure to connect to your internet access provider?

  What error messages are reported?

  Event Viewer reports

  1. normally, when an error occurs on your computer looking in Event Viewer should be your starting point to find a solution. More related system errors are recorded and get an exact copy of the relevant report is important. Unfortunately, is not easy to understand reports and most of the users computer need help with their interpretation. I have to say later interpretation.

  2 Event Viewer includes three main newspapers of Windows. Here's the Application, security, and system. For purposes of troubleshooting system is by far the most important.

  3. to access the system log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window select Windows and the system logs. Place the cursor on the system, right click and select filter current log. Check the front of the error and click OK and see you only reports errors. Click the Date and time column header to sort. You may need to click a second time to see the last report above.

  4. a tip for posting copies of error reports! Run Event Viewer and double-click the error you want to copy. Select the Details tab and check the box in front of the XML view. Click the copy button to place a copy in the Clipboard and close Event Viewer. Now start your message and paste it into the body of the message. Make sure that it is the first dough right out of the event viewer.

  5. He cautioned against three types of reports, information, and reports errors. In most situations, it is the error reports that offer the best information but sometimes WARNING reports provide useful clues.

  6. all reports have stamps date and hour and when troubleshooting, it is important to focus on the latest reports. Reports of studies from the point when the computer is started, and then check if a similar report appeared in the previous session. If errors do not repeat investigation as to why they happen is wasted effort.

  7. in the individual reports the most important information is the event ID and Source such as these help when looking for help on the internet. The description is just as important and copy the exact text to use as search criteria greatly helps achieve better results when using Google. Not paraphrase descriptions when other people asking for help.

• I installed the Socks5 & IPIG connections & after my vpn connection simply stopped working.

  stopped my VPN connetion working.what I do?

  last night, I installed the Socks5 & IPIG connections & after my vpn connection simply stopped working. I don't know if it's because of Socks5 or IPIG connections but I tried everything, including the restoration of my windows & uninstallimg 2 connections, I even deleted all my internet connections, including vpn & them reinstalled but nothing worked.when I click the vpn connection, it just shows that this message saying could not be contacted.

  is my windows homebasic .plz help of vista...

  Hi Melanie,

  You can consult the following articles and check.

  You receive the error code 741 when you try to establish a VPN connection type PPTP on a computer running Windows Vista

  Troubleshooting remote access VPN

  If you are working on a domain environment, then you will need to contact the system administrator for assistance.

• Vista 32 bit loses the internet connection after about 10-15 minutes.

  I lose my internet connection after 10-15 minutes.

  The message says local access only.

  The only way to reconnect is to restart the computer.

  I use a devolo home plug network system. It is connected to a 210 of BT router travel.

  I also have a new computer recently bought and installed Windows 7. There is no problem with that.

  Maybe it's a coincidence, but the problem started only since the installation of the new model.

  
  

  Hello Cody C.

  Thanks for your reply. I tried this. It is said that the drivers are up to date.

  I go into the settings of power network and checked the box "turn off network card to save energy.

  Since that seems to be OK. Only time will tell if.

  Thanks a lot for all the replies. EXTED