No signal on monitor after Windows 8 logo

Similar Questions

• Satellite A300D-16W: Signal weak WiFi after Windows 7 installation

  Can someone help me what to do?
  My W - lan gives only 3 lines offline after installing Windows 7 Ultimate edition.

  When I move my computer more then 3 meters, then connection is lost.

  I have another laptop and it works fine on the modem wireless within the whole of the 100% home connectivity.

  Hi mate

  First, you must install a new WLan driver.
  You can get the latest version here:
  http://APS2.toshiba-tro.de/WLAN/

  In addition, I recommend disabling for the WLan to save energy.
  You can do this in Windows 7 power management!

  Last but not least check the settings in the device-> WLan card Manager-> properties-> Advanced tab.
  Here, you can increase the performance of the signal.

• does not start after windows xp logo at startup

  After a power failure, the computer never exceeded the windows xp on Startup logo.

  Dell 8400 dimension has avg free and pc tools spyware doctor pack.google.com I don't know service pack.  No cd of xp in addition to the one supplied with the computer.

  I tried to use f5, f2, f8 or f12 in my quest to resolve the problem by using the software.  I have reinserted the cd of windows and tried r and enter for a new facility and it times out to examine 76294 MB disk 0 at id bus 0 0 on iastor...

  I tried to start in safe mode, the first screen of scrolling words then nothing.  safe mode with command prompt the same thing.

  I reinstalled the memory and still nothing.

  I tried knoppix, but the computer would not boot from the cd - r I've burned just the software on so that I could write zeros to the hard drive.

  I just want to clear everything and start over, but I don't know how.

  Help!

  I put in my windows 98 cd from dell, which built repair tools.  I'd wipe the hard drive for me and then I went through the steps to reinstall xp and it took finally.  I had to make a quick partition of the hard drive with xp cd because along a guarded suspended at 4%.

  my computer is back running with windows xp through my windows 98 from dell factory drive.

  I hope this helps.  I reinstalled on 18 January, I get all the time to tell you my dose.

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• Dell Optiplex 3020 - the black screen after dell logo (happened after windows updates froze at halfway and systems were restarted)

  We had windows updates run on all our systems of windows 7 in our medical center.  13 or so of our 3020 s Optiplex froze for eight hours about in a State of "install updates 1 of 24".  I have all them turned off and restarted units.  Once units have been restarted, they gave the Security windows startup or start-up option normally.  Those who had selected the option to 'start normally' would display the logo dell at startup, then click on a completely black screen (all devices still in market and monitors recording an active signal even if no picture).   Those started in safe mode w/o networking, loaded in safe mode.  I rebooted the machine in safe mode, and they all started out in windows without problem.

  For systems that go completely black after the dell logo.  I am able to F2 in the BIOS, I can run diagnostics from BIOS and I can't F12 in boot options, but I cannot F8 or SHIFT + F8 mode without failure or fact start in safe mode, please come under early start options.

  Anyone happen to know a way to launch a system of 3020 optiplex in safe mode without the use of F8, SHIFT + F8, go through msconfig or remote access to the registry (because I can not remote in the system on the network)?

  Maybe I can put the hard drive in a dock and change the registry in this way?  But can I change the potentiometer to force secure boot? or is it not possible to make a bcdedit to it as an external drive, install it in his camera and force it to safe boot the next time, he is running?

  Any ideas or suggestions would be very appreciated.

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  I suggest you to send your request in the TechNet forums to get the problem resolved.

  Please visit the link below to send your query in the TechNet forums:

  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Re: satellite A300 screen turns off after the toshiba logo, will not boot from the CD/DVD

  Hello, I have this problem with Toshiba satellite A300.

  I deleted several files and folders of my drives C and E. To restart the computer, it only shows the Toshiba logo then a slightly gray white screen on a thorough inspection. Whenever I press CRL + ALT + DELETE, the computer restarts and behaves in the same way.

  I tried to use an external monitor, but there is no difference. The tent to start using a CD/DVD, same behaviour occurs, it does not start and screen remains blank after the Toshiba logo, I tried even to change g the order of boot, but in vain.

  What could happen?
  Thanks in advance.

  Hello

  It seems that you deleted system files and Windows no longer starts. Have you tried to restore the disk image factory settings or hard drive recovery? Or do copy the Windows installation... It is easier to reinstall rather fix the problem.

• No output on the monitor after the system resumes

  After the system goes into hibernation mode, then the mouse is moved or no key is pressed, the monitor does not come to the top again. On the keyboard it no NumLock light at the moment, although num lock is also pressed. If at this time monitor is turned on, it displays "VGA input No Signal" and monitor goes to sleep. Only way is to force a reboot of the system

  Hi AnjanaKumar,

  There are a few things to possibly resolve this problem.

  1. you'll want to make sure you update your video drivers directly from the video card manufacturer's Web site.

  2. it could be the power plan that you configured is not compatible with your configuration:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-create-or-delete-a-power-plan-scheme

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Loses the signal of monitor

  System:

  CPU: AMD Athlon X 64 Dual Core 2.6 GHz

  Motherboard: ASUSTeK M2N - MX SE Plus

  RAM: 2048 gigabytes

  Graphics card: MSI 7300 initially, then a PNY Geforce GT 520

  Storage: A WD 200 and a WD 500

  DVD: A (unknown model)

  Monitor: LG W2242T

  OS: Windows 7 Home Premium

  Stats:

  04/12/2012, I bought a copy of Windows 8 Pro for my personal system (not above).

  07/12/2012, I bought a 2nd copy of Win 8 Pro for, the above family system.

  12/7, I started to install Windows 8 Pro system above with the MSI 7300. The facility would go to which appeared at the end, but towards the end, he would show graphics on a blue background. Then he would show no signal on the screen, and the lock, I turn off and then restart. Once restarted, I constantly had the installation message failure and loaded windows 7. After several test all resulting in the same situation, I bought the PNY 520 thinking the MSI 7300 GT was the problem. Unfortunately come with the same lock upward and scrambled graphics. I have tried 15 to 20 facilities work my bios, all to nothing does not. Then, in desperation I downloaded the Win 8 Customer Preview and tried and it INSTALLED and RAN PERFECTLY.

  I'm afraid to try the 8 Win pro on my personal system until I get the functioning of the family system and understand what is happening. Any help is greatly appreciated, thanks for posting and email* address email is removed from the privacy *.  I'll give you my cell phone number if you ask in the interest of understanding and solving this frustrating problem.

  Hi glenblaha,

  You can see these links and control which should certainly help u.

  http://www.TechRepublic.com/forum/questions/101-302418/monitor-keeps-losing-signal

  http://www.TomsHardware.com/Forum/115113-13-monitor-losing-signal-playing

  http://www.TechRepublic.com/forum/questions/101-300412/loss-of-signal-to-monitor-but-PC-still-running

  All the best!

• Laptop Presario CG56: CG56 crashed after Windows Update

  After Windows update, set during the race, woke to find a "scree Orange" with the logo of Compaq.  Press F11 to enter in recovery mode has organized the restoration of the system for each restore point.  Finished with 0x8000ffff.  A ran the recovery system completely at the end.  Finished with the Orange screen.  Minimized ran impage recovery all the way to the end.  Repeat screen Orange.

  I find that the BIOS is corrupted in Windows Update, somehow.  I can get to the line of command in recovery mode, but I don't know what to do.

  Help!

  Me am HP Advanced System Diagnostics V3.0.3.0 by pressing f2 until the screen has finally come.  Do you have the System Diagnostics.

  Have you hard reboot by removing the battery, press the button for 15 seconds, extra power, hit start and the start up like a new PC was started and Windows.

• Start normal mode after windows xp bar charge it gives black screen and in safe mode it gives blue screen

  Victorinox original title: Black scree & blue screen...

  So my laptop that is running Windows xp, start in normal mode after windows xp bar charge it gives black screen and it stays like this, and in safe mode it gives blue screen, what can I do? I need your help atleast to save the files to my hard drive...

  Hello

  · What is the error code or error message that you receive when the computer starts in safe mode?

  · Were there any changes made on the computer before the show?

  · What is the number and the model of the computer?

  · Who is the service pack installed?

  Try the methods below:

  Method 1: Disconnect all the devices connected to the computer such as printers, scanners or USB hard drives and restart the computer and check if that helps.

  Method 2:

  Try to start your computer in last known good configuration. You can check the link for the procedure: how to start your computer by using last good known Windows XP Configuration: http://support.microsoft.com/kb/307852

  Method 3:

  You can follow the steps listed in the link: after the Windows Logo appears, or after you log on Windows, a Windows XP computer can display the wallpaper, a black screen or a blue screen: http://support.microsoft.com/kb/318027

• out of range signal to monitor

  out area error range on monitor to signal when the connection of the laptop vga cable

  Hi jolynne60,

  If I understand the only thing that appears on the monitor is the message about signal, splash screens and Windows are not displayed, please correct if I have understood you.

  It is a hardware problem, whenever these types of messages appear on the screen, the monitor may not detect or the implementation of the video signal.

  Who is the manufacturer of your laptop?

  The following steps are worth a try:

  1. make sure that the computer is connected to the monitor is using the correct video output source.

  2. If the monitor has an input or source button, press the key.

  On some monitors, the entry or the video source selection lie in the on-screen menu system. If Yes, press the Menu button on the screen and the buttons on the front panel allows you to select the video input.

  You might want to know

  Connect-your-computer-to-a-TV

  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-your-computer-to-a-TV

  If the problem persists, contact the computer manufacturer for assistance.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Inspiron 7000 (7537) problems after Windows 8.1 update

  I have my laptop set updated to 8.1 and I found 2 numbers to date:

  1 - my wrath of monitor off after 30 minutes when it is plugged in, but back on. That has happened twice and had to force close down. (laptop wasn't on sleep)

  2 keyboard and touchpad"could not start" after windows starts, so I got back the password using the screen keyboard and restarted windows.

  - - - - - - - - -

  UPDATE!     24/11/2013

  seems that Intel has finally resolved the issue, released driver 3345.

  go to system Intel detect the site and to detect your system for updates: http://www.intel.com/p/en_US/support/detect

  This update has many bugs and most importantly: fixed black screen that occur during the recovery of an automatic monitor off scenario.

  fixed link: http://downloadmirror.intel.com/23405/eng/ReleaseNotes_GFX_3345_64.pdf

  UPDATE!

  seems that Intel has finally resolved the issue, released driver 3345.

  go to system Intel detect the site and to detect your system for updates: http://www.intel.com/p/en_US/support/detect

  This update has many bugs and most importantly: fixed black screen that occur during the recovery of an automatic monitor off scenario.

  fixed link: http://downloadmirror.intel.com/23405/eng/ReleaseNotes_GFX_3345_64.pdf

• My screen goes black and the start menu does not load after start up logo and the only thing on the screen I see is my mouse pointer

  My screen goes black and the start menu does not load after start up logo and the only thing on the screen I see is my mouse pointer

  Hello

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have your system disks
  manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore there only to)
  being bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - type no parenthesis)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• DisplayPort that NO SIGNAL appears in the window on the screen is good

  DisplayPort that NO SIGNAL appears in the window on the screen is good. I run all programs without any problems. But this small window in the upper right corner will not go away. Any help will be appreciated.

  Hello

  To make the small window is closed on your screen, please try to perform an end task. If does not end the task, there is an option that attempts to put an end to the tree of the whole process instead of just the individual job. Select the Details tab in the Task Manager, right-click the process you want to end, and then click end process tree. This will attempt to leave the program and all associated process.

  If the same small window is always on the screen, I suggest that you try to unplug your monitor from outlet for a minute and plug it back again. This should refresh the settings of your monitor and the small window should disappear.

  Let us know how it goes.