OfficeConnect router modem problem

Similar Questions

• Linksys E2500 connection to the router/Modem Combo?

  I have a Linksys E2500 and I'm trying to connect to my service provider supplied router (Actiontec V1000H) because I wanted the best range and consistent connectivity for my 6 wireless devices.

  My problem is that, to do this, I connected an ethernet cable from the yellow the E2500 internet port one of my V1000H LAN ports. This, however, did me not internet access even if the network for my E2500 was available in the network list and selected as the default network. I then had to go the the E2500 advanced and changed the IP address of the router from 192.168.1.1 to 192.168.2.2. This gave me internet access.

  However, everyone I talked to including employees and experts at dslreports said that, because of what I did I put in place a double NAT with 2 potentially conflicting of IP addresses and on the road weird questions will arise because of this. They suggested that the E2500 connect to a modem dedicated to avoid this problem. However, the dedicated modem, that I was sent was defective and did not allow for access to the internet, even through the ethernet connection. So, until I get a new modem dedicated, I have to use the combo router/modem.

  What should I do? Should I implement the E2500 as just an access point wireless for my modem/router combo existing? What should I change in the advanced settings? Or is there an alternative?

  Check this link:http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.xml&pid=80&r..., this will help both routers LAN - LAN cascading.

• I want to use a Terminal Airport Express to extend network provided by my Fios router/modem without going through another airport base.  Is there a way to do this?  I understand that Apple does not support this, but surely there must be a way to do this.

  Can someone tell me how to set up an Airport Express Terminal to expand Network provided by my Fios router/modem without going through an airport as a base?  I understand that apple does not support this use, but my applecare Advisor said it's possible.  Thank you!

  Unfortunately, your AppleCare Advisor is wrong if he or she has told you that an AirPort Express to extend wireless signal of a Fios router/modem.

  Function of "Extend a wireless network" Apple is an exclusive feature that was designed by Apple engineers to extend the signal from another wireless only router from Apple. Thus, the AirPort Express... or any other router Apple besides... would not be able to extend wireless a Fios network.

  SO... you have the possibility to locate the Airport Express where it is needed... And... Connect it to the Fios router/modem with a permanent, wired Ethernet cable connection, then the AirPort Express can 'extend' in this way.

  Or... If you are ready to add a second AirPort Express, connect the first near Fios modem/router with an Ethernet cable, then the second Airport Express could extend the signal first Express wireless.

  Another way to say the same thing, is that if you want an Apple AirPort router to extend wireless network... then you need two Apple routers to achieve this goal.

• All in a single 228 MS cannot find my router/modem to connect to the internet

  I just replaced the hard drive on my desktop MS 228 All In One. I installed windows 7 Home Edition premium and everything seems ok. The computer displays any internet connection included, even though we have a laptop computer and two tablets
  Connected wireless to our router / modem box. I got this computer connected wireless, until the hard disk is dead. I do not understand why it cannot locate the internet now. I get the message to connect to the computer with a cable, but I need a Wi - Fi connection because the internet area is some 3 meters across the room!
  What should I do for a wireless connection? I must have done a few years ago, when I first installed this computer... but
  Do not remember how I did it... Help please...

  Thank you very much Dunibar, all this work after having followed your instructions... your a star.

  Very much appreciated. What ABOUT James... Maxiboy.

• I have an airport time capsule that was related to my router / modem.  I changed my router for a better.

  I upgraded my router (modem).  Now my wifi has a different name and different password.  What should I do to ensure that my Airport time capsule is always related to the router - even if it always shows the green light.  How will I know if the airport is still save properly?

  How will I know if the airport is still save properly?

  You can consider trying a backup to see what is happening.  If you decide to do...

  Click the 'clock' Time machine at the top of your Mac.

  Click back up now

  

• Modem router connection problems

  Hi all

  I am replacing a belkin n600 with router linksys ea6350 router. The modem I have is a Motorola Surfboard SB6141. The belkin router connects perfectly to the modem, but when I try to connect the linksys router to the modem, the light on the router keeps blinking and will never get me connected to the internet. I even tried to connect the linksys router to the router belink when the belkin is connected to the modem. I still don't get any kind of service. Thought it was a bad router and it took for my current home to connect to my modem At & t and it worked very well and I was able to put everything in place. For some reason I don't know why the linksys connects very well with the modem at & t, but not the motorla modem and the ISP that I have in my apartment is Comcast. It does not any sense and I'm heading home in a few days and I really need this connected linksys router belkin router is just too slow. Please I need much help getting this linksys router to communicate correctly with the motorola modem. Also, I used both crossover and straight cable modem to see if that makes a difference and does none of this and I know use cross to connect to the router.

  first of all, make sure that the port on your pc is enabled.  usually, if you enable wifi it disables the ethernet port.  before you turn off the modem and do a factory reset on the router into the RED reset button until the lights on the router are flashing.  Turn the power off and wait 10 seconds then plug it back.  During its initialization connect a straight cable between the pc and the router's lan port.  Also, connect a cat5e or cat6 from the wan port on the router to the modem.  wait until the router finishes starting, and if she opens a browser in itself and then open a browser (ie to try) and put 192.168.1.1 in the address bar.  You should get a connection.  Let the empty user and enter "admin" for the password.  Or if it opens the programme of assistance to load the router you can follow if you wish.  This should get you.

• Loss intermittent connectivity... Airport express router or modem problem?

  Airport express intermittent loss of connectivity?

  Not much information to go here.

  Please provide at least the following details:

  • What exact model of the AirPort Express model do you have?
  • What is an intermittent loss of connectivity? The Express, iPhone, another thing?
  • This working before and just started happening OR if this has always been a problem?
  • Did you do the upgrades of firmware or software recently, when this started to happen?
  • What have you tried so far, to solve this problem?

• Impossible to establish a connection between microsoft router, modem, motorola and dell/windows xp computer

  I have not set up a connection between my computer dell/windows XP, Microsoft router and my Motorola modem. After reading the instructions for the router and set up like it says anything I've set up my computer say it is connected but is not really plugged. My ipod says that there is this WiFi but when I try to access the internet on it, it gives me a message saying "unable to connect to the internet, there no connection detected." The only time where I have Internet on my computer is when I unplug the Ethernet to the router and modem and have the modem only connected to one computer. This problem is can cause because my modem is configured with a cable from cox and not connected to a phone cord? (My router is a Microsoft Broadband networking Base station wireless MODEL: MN-500) (My modem is a modem cable Motorola surfboard implemented with internet helmsman) (My computer a DELL Dimension E521 with a windows XP service pack)

  SP3 is on it? Wireless is enabled on the router? Try this

• Is this X 1000-E1 300mbps router modem?

  First of all, I'm of the Greece.

  I have the Linksys X 1000 - E1 modem router

  My only problem with this modem router is that I've never had of 300mbps, but just 150mbps. ("I use the program" XIRRUS wifi Monitor ")

  Why is this happening? I think that this gateway is 300mbps, or not?

  You must configure the active X 1000 for 40 Mhz, WPA2 Personal, and Support WMM wireless connection. The computer's wireless adapter must be capable of 40 Mhz.

• Router modem does not recognize

  I use a Modem SB5120 Motorola on Comcast, which works perfectly well when it is connected directly to my computer or my old router, a Linksys WRT120N.

  The router is dying slowly, so I bought a new one (Asus RT - 53N). He could not recognize an incoming WAN signal and establish an internet connection, with the exception of one, several hours window. In the contrary case, it seemed to work fine.

  I returned it and bought a Linksys E2500, who seems to have the same problem, because it does not receive an IP from the modem.

  I tried all the settings of the previous router (MAC clone, DNS1 and DNS2 address) mirroring unsuccessfully.

  As far as I know, the modem is not compatible with the newer routers for a reason any (I have or all 4 tech different support people I called) can't think, or there is some kind of configuration setting I'm missing. I'd appreciate any help before I go and buy a new modem.

  New modem resolved the problem.

• New router BEFSR41 problems installing...

  I just installed a new version of my BEFSR41.  I had a version 2 and now have a version 4.3.  I have Road Runner internet and had no problem, just pick up my old router and hang a new.  A restart of the modem and I was able to connect to internet and my other 2 computers in the House.  However, I can't access the 192.168.1.1 configuration it won't let me past the password screen.  I tried the default "admin" with no luck.  A reset of the modem will fix this problem without screw it my internet connection and network...

  Also I had installed LELA and when I installed the new router it showed it as a gateway instead of the BEFSR41 router as he showed before.  I reinstalled but still the same bridge description. I uninstalled the program.

  TIA

  Your router must have a username is blank and the password "admin" (without the quotes).

  If this does not work, then the most likely cause for your problem is a problem of computer software firewall.  Go into your computer and temporarily disable your software firewall and see if that allows you to connect to your router.  With some computer software firewall, you will need to "trust" your router at 192.168.1.1

  If you still have problems, read on:

  Here are my tips for to connect you to your router:

  You need not be connected to the Internet to view the router's web pages.  These web pages are built into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then most likely your modem is actually a "modem-router". Check if your "modem" is using the same address as your Linksys router 192.168.1.x space. If this is the case, then the report with this problem and specify also the brand and exact model of your modem number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system. It should work.  Reset the default router will also reset your default Internet connection type.

  If the reset does not fix your system, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• New router connection problems

  So I just got a new router delivered to my cause of House, that we had to move to a new location, and that we have obtained will not let me connect to the internet via a modem-> router-> computer.  It works very well when connecting with the computer of my brother through wireless. When wired to the router I get full connected via the internet and so on, but when it comes to my computer wireless router, do not let me go beyond "local only". He remains as unidentified network and can't get more than that.  Ive tried to restore my computer to Service Pack 1 and remove Norton from my computer with the removal tool and nothing seems to work. Ive changed my setting of the router mode 50MBPS and stuff and nothing, defining the network IP and DNS in my Protocol which is in my router and that did not work either, my IP address restarts and refreshing, nope. Im running Windows Vista Home Basic with an Atheros AR5007 802 network card. 11b / g. router Netgear WNR1000v2.  I had a problem with my computer with my last router.

  It's my connection information:

  Microsoft Windows [Version 6.0.6001]

  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  
  

  C:\Users\***>ipconfig/all

  
  

  Windows IP configuration

  
  

  Name of the host...: *-PC

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  
  

  Wireless network connection Wireless LAN adapter:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-24-2B-C8-1A-21

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  
  

  Ethernet connection to the Local network card:

  
  

  The connection-specific DNS suffix. :

  Description...: Realtek RTL8102E Family PCI - E Fast Ethern

  and NIC (NDIS 6.0)

  Physical address.... : 00-1F-16-70-E0-A5

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::a85c:6ec9:2 has 4: bbf5% 10 (Preferred)

  IPv4 address: 192.168.1.4 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Monday, November 29, 2010 14:29:05

  End of the lease...: Tuesday, November 30, 2010 14:29:05

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  
  

  Card tunnel Local Area Connection * 6:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {E418D763-0DB4-4DCA - B 9, 70 - E94D132E8}

  62 A}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 7:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {F2AFB4E5-A1E8 - 415 B-A7B3-A433B3227}

  715}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 11:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

   

  Any help would be appreciated.

  
  

  Well, I tried everything you listed on here and nothing seemed to work. I found a good solution to change my WEP security and he recognized her. Looks like it has problems with the other encryption security. Thanks for your help though!

• Factory reset wireless router connection problems?

  Hello

  I recently did a factory reset on my HP6745f desktop running Win7 sp1 and I don't know if my problem is with HP or Linksys/Cisco (my router). I already contacted the support Cisco who reported the problem seems to be "a matter of HP, a corrupt driver or other third-party issue" and then offered to help, for a price. I'm hoping to avoid that if possible.

  This office computer is directly connected to the router via an Ethernet cable. Cisco software was that I want to install that 'control' of my router (called Cisco Connect) and when I try to install the software, I get a message saying: "We could not find your router" (that's why the software will not install) - although I am accessing internet through that router. Even if I try to enter my network name and the password, it cannot find anything. I am also unable to access the router via my browser "168.198.1.1".

  I am unable to connect wireless with the same desktop so, my 2 wireless laptops have no problem of connection at all, which leads me to believe it's something specific to my desktop pc.

  The Cisco Connect software has already been installed on my desktop and it worked fine. I guess my question is: someone has any suggestions for me? This could be a driver problem? How can I identify what (s) for 'check '?

  Any help would be greatly appreciated.

  I thought about it! My router can use a "network key" to connect other computers to the router. I guess when I reset my pc all this info has been removed and the router could not communicate.

  I have just created a network key on a flashdrive USB of my laptop, plugged the USB in my office and hop, I reconnected properly. Thanks for the suggestions, I really appreciate the help.

• Satellite L300 - 1 year PSLBGE - device Modem problem

  Hey

  I try me set up my dial-up access, so I can use internet at home...
  It is said that any modem devices are
  but in the previous copy of windows that I had... everything was fine.
  would u please help me solve this problem?

  Portable computer system unit Toshiba satellite L300 1 year
  Model No.: PSLBGE-002004AR
  OS: Windows XP
  Note: I went on the site of toshiba drivers and I downloaded 3 files of modems here to try to update the modem driver
  but nothing helps and the problem persists
  Thanks for reading
  Your
  ~ Nour

  I guess that you have activated the Device Manager and there is no yellow exclamation point isn't good?
  Figure modem in the list?
  It should be!

  How have you tried to configure the dial-up access?
  You should do this;
  Go to the category modems Options - Control Panel - hardware and sound - and.
  In the local info window, select an area code; for example, 0.
  Then click the Modems tab, click Add.
  If a User Account Control warning window appears, click on continue, and then click Next.
  Now Windows Vista should attempt to detect the modem.
  When the modem installation is complete, click Finish.

  Then the new modem installed should appear. Click OK to close the Options of Modem and telephony.
  Now, your modem is installed correctly, and you must now create a modem connection.

• A300D-14 t modem problem

  I change my version vista Home Italian English version, but my toshiba sat. A300D-14 t does not recognize the modem hdaudio and does not install the driver from toshiba site could someone help me to solve this problem the solution pls.

  XP or Vista?

  If its XP:

  http://support.Microsoft.com/kb/888111
  http://support.Microsoft.com/kb/835221