OfficeJet 6600 not recognized Via a USB connection

Similar Questions

• We get the popup "USB device not recognized", when nothing is connected.

  Original title: pop up message

  I connected the USB cord to transfer information from your old phone to new phone via Itunes.  Since that time that I keep getting a pop up message that says: device not recognized USB, the defective device, windows does not recognize.  Nothing is plugged in, but message appears every few seconds.  How can I get him to stop?

  Hello

  It seems that you are getting the popup "USB device not recognized", when nothing is connected.

  What is the brand and model of your computer?

  I suggest to uninstall the USB controllers and check if you get the context menu.

  
  

  Method 1: Remove and reinstall all USB controllers

  
  

  a. clickStart, type devmgmt.msc in the start search box and press ENTER.

  b. expandBus USB controllers.

  c. right-click on each device under theBus USB controllers node and then click Uninstall to remove them one at a time.

  d. restart the computer, and windows will install the rear USB drivers.

  If reinstalling USB host controllers fails to resolve the issue, go to method 2.

  Method 2: See the procedure suggested by johnkelly46 responded on October 26, 2009, from this link.

  If you have additional problems, please reply to this post and we will be happy to help you further.

• I try to register with a mixer via a usb connection. I can tell I have the settings correct, selected in the hardware Audio section. It worked before, but it's not. Any ideas? It's driving me crazy!

  I try to register with a mixer via a usb connection. I can tell I have the settings correct, selected in the hardware Audio section. It worked before, but it's not. Any ideas? It's driving me crazy!

  That entry of casings do you use on the Yamaha and what you've plugged into them? With the whole level at about 01:00 controls, as Neil suggests, increase the Gain until the red LED on the channel starts flashing. And then put it down a bit so that it no longer lights except very occasionally. You should then see the green signal LED flashes but not the red. You should then have reasonable level in hearing.

• Why my iphone will have problems with pandora in synchronization with the pandora application on infotainment chevy via a usb connection?

  Why my iphone will have problems with pandora in synchronization with the pandora application on infotainment chevy via a usb connection?

  This was never resolved?  I have the same problem with an iphone 6s.  It is only my phone like an ipod playback.  I don't get the interface of Pandora.

• HP Photosmart 7280 not recognized via WLAN MAC OS 10.7.4 Lion

  The problem: HP Photosmart 7280 not recognized via WLAN MAC OS 10.7.4 Lion on my Mac Book Pro (end of 2011)

  What I tried:

  Reset the printer, reinstall the HP software, update via Apple update Routine.

  LAN works perfectly.

  My iMac 24 "with 10.6.8 Snow Leopard WLAN print works perfectly.

  Sitting right next to my iMac with my new laptop, the printer does not appear in 'printers '.

  Someone has an idea or knows this problem?

  Thanx for some feedback

  jhwb

  Download and install this: http://support.apple.com/kb/DL907

  Reset the printing system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• OfficeJet 6600: HP Officejet prints 6600 pages of test, but USB connected or wireless - does not print anything

  Hello
  For some reason any my printer has ceased to be able to print anything at all, since last night at 7-8 so far, I've been able to print perfectly well.

  It is connected wireless (and on the home network and the IP address), but whether or not it is wireless (USB) - nothing will be printed at all.

  Have tried everything imaginable... uninstalled and reinstalled all HP 3 or 4 times now, various attempted fixes via the online help, nothing works. Have unplugged router printer 30 s, unplugged 30s, you name it.

  It allows to print in-house, however, no problem. Print a test - perfectly fine page, print a network test page - perfectly well. Clear print heads... everything comes out clear.

  Spotted an error prompt "spooler subsystem app not working not"... so found this page online (https://social.technet.microsoft.com/Forums/windows/en-US/460f297a-dd66-4476-a176-542e1519ca3e/fixed... and thought it was the miracle solution - nope, still doesn't.)

  Followed the steps detailed here: http://h30434.www3.hp.com/t5/Inkjet-Printing/HP-6600-won-t-print-wirelessly/td-p/4649292 - the link to the HP Print & Scan Dominican Republic by the way, is a dead link now... but I have tracked down the appropriate page and run the software. After following it exactly as I had to... I get this result:

  "There is a problem with your software which can not be repaired by this tool. Remove the software by clicking 'uninstall '. Reinstall the software with the product CD or by downloading the latest features full software from HP Customer Care. "- so in other words... I am told to do exactly what I've already done 3 or 4 times.

  It's driving me crazy... and do not understand why it will not print.

  I hope someone here can help... because it's completely maddening.

  Hello
  By coincidence, my grandson has me bought a new computer earlier in the month. and it arrived yesterday afternoon, a Lenovo all-in-One ThinkCentre w/Windows 7 - and after it he installed there, the printer printed fine from the computer.

  But, just in case it is needed, and because the advice was here, I thought I'd try the options.

  Unfortunately, I can't do a level 3 uninstall with the two methods provided. Method never showed a "util" folder or 'utility', both had a "utils" folder, and no method showed a record of "ccc". Also, by downloading the software, then go into the temporary folder through the search from the Start Menu, 3 sets of disc records came - and such that mentioned, none had the util/utility folder (all "utils" still had once) - and yet, none of them had a folder 'ccc '.

  My grandson theory was that something is likely messed up in the registry, and he doesn't dare touch it without knowing what it does - than a reformat or something registry editting and knowing exactly what they're doig - would be the best choice, but rather of your time and... almost useless with the new computer capable of printing. A friend IT very well educated friends, also backed up his theory...

  So, I have to wonder... don't you think it's worth, the Dungeon of combat with the old Gateway/Vista PC, or simply move to the new Lenovo/Windows 7 and cause less stress for us all? Haha!

  Thank you for trying to help but... it's too bad the computer unfortunately does not cooperate.

• HP 10 more 2201RA not recognized under windows 7 connected via usb

  As the title says. Receive connect the tablet to my computer via the USB port nothing happens. The device is not displayed. I followed the instructions in the troubleshooting section (Manager of peripherals and USB Root Hub etc.).

  The SDA device appear the first time that it has been connected, last night. However this morning... nothing.

  After using the connection to synchronize from the MyDocs toGO application, I unplugged the unit. I do not however the disassemble everything first.

  Thanks for the responses...

  I went with... done AirDroid work, works great and is wireless.

  See you soon

• Devices not recognized unless it is connected through a USB expansion port

  Came to use a scanner that was not used for some time and unrecognized device.  Tried reloading drivers, but still no good. Bought the new scanner/printer combo, but not recognized after loading software.  Finally managed to make it work via WiFi. Thought, I'd better try another material... iPOD touch... "unrecognized ', Sony e-raeder..." not recognized '... panic!  Has finally got the devices to be recognized by the connection via an expansion Belkin 4 port hub.  Any ideas on how to solve the problem of USB ports not recognize my hardware when connected directly.

  Have you tried to update the drivers from the chipset manufacturer of PC or motherboard manufacturers websites?

• My keyboard is not recognized by windows when connected to the USB ports.

  My keyboard is not recognized by windows because that is malfuncioned or something else, that's what I get a message when I insert the keyboard to the usb port that could do because the ports are fine.

  Original title: keyboard problem

  Hi Caragata,

  Perform the steps from the link below and see if it works.

  Tips for solving problems of USB devices

  Note: This article also applies to Windows 7. If the fix it does not work, you can then run the built-in utility.

  Good day!

• MacBook Pro not recognizing the Cougar USB install

  I have a Macbook Pro 5.2-17 "retina display. I replaced the hard drive and I am installing Mountain Lion. The hard drive is not an SSD. It's a 500 GiB Western Digital SATA, partitioned with TPG and JHFS +.

  I started by installing El Capitan, because that's all I had. The installer of El Capitan is on an external USB drive that is partitioned. When I boot using the down Option key, the C key or command-R, the installer of El Capitan is recognized. I installed El Capitan, created an installer of Mountain Lion on a different partition on the same external USB drive and erased El Capitan the internal hard drive. When I boot on the USB setup of Mountain Lion is not recognized. Setup of El Capitan is recognized correctly. Why not available in boot manager during startup? When I got El Capitan installed, the two partitions have been recognized very well when I plugged in the USB. Both were mounted and appears on the desktop. So I know that the problem is not the USB key, or 2.0 or 3.0, or the recovery partition because I erased the disc and the recovery partition is no longer exist. How can I get the installer of Mountain Lion to be recognized at startup?

  I did the command Option P R, NVRAM reset several times. No joy. The only partition recognized at boot time is the installer of El Capitan.

  I want to level back to Mountain Lion because it is less intrusive than El Capitan and will be more familiar to the person who will use this computer.

  Oh, and more than two elements. When I start the installer for OS X from the external USB drive, I gives me three options on where to install TO - install OS X El Capitan, install OS X Lion mountain and Macintosh HD. Therefore the partition setup of Mountain Lion is recognized, but not as an installer to start from. Although when I plugged in the USB port when El Capitan was installed he showed as an installer Mountain Lion.

  Also, there is NO option to choose where to install FROM. If I have two installation programs, I have two choices of installation?

• Re: Portege R100-11Z no audio signal through headphones/mic not taken, via its USB OK

  Hello

  I did a clean install on my Portege R100-11Z of windows 7 and later a new clean install of Windows XP Prof SP3.

  In both configurations, I have no sound from the headphone/microphone jacks. (yes I check all the options: mute / his wheele next / new drivers / Toshiba eliminate program "mute" e.t.)
  All the configuration looks OK. I don't see anny WARNING/message in the configuration settings.

  But I hear via a USB headset via the USB.

  Looks like the built-in sound card Driver works OK because I get the sound through the USB.
  What is the solution to get the sound through the headphone/mic shots?

  Thanks for your help/advice.

  Will be

  > In two configurations, I have no sound from the headphone/microphone jacks.

  But that the sound from the speakers?

  Theoretically, it could be possible that the headphone is faulty
  Inside the headphone jack there is a little switch that switches between speakers and headphones.

• My LaserJetPro 400 printer is not recognized on the USB ports. With the help of El Capitan OSx

  Since I installed OSx El Capitan, I had intermittent problems with the USB ports to connect to my HP LaserJet printer. I first thought that the older printer was not compatible with the new OSx software, so I've just upgraded to a new HP LaserJet Pro 400 M451dw. same results and the computer is not even connect to the printer. The number of post detailing a similar problem, I would hope that apple now had a fix for this problem...

  It gets very frustrating to say the least.

  Help

  T Cooke

  HI T Cooke,

  Welcome to Apple Support communities.

  The article below provides a lot of information and troubleshooting tips that may help you solve problems with your MacBook Pro grateful and print to your printers.

  OS X El Capitan: print troubleshooting

  Ciao.

• Why my HPavillion keep crashing when I try to print using my HP Officejet 6500 has more using the USB connection?

  I tried to update the driver, but couldn't.

  Hello

  1. do you receive any error messages?

  2 have you made any changes to the computer before the show?

  3. who is the operating system installed on the computer?

  4. is this problem limited only when connecting the printer via USB?

  5. what happens when you try to update the driver?

  Run the Fixit and perform the steps mentioned in the article:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  I suggest you provide more information about the issue so that we can better help you.

  I hope this helps.

• Apple Airprint for HP Officejet 6500 has more via a wired connection to the router

  Hello

  So I did a considerable amount of research in this through the internet and this forum and I still struggle to find a satisfactory solution.

  I have a HP Officejet 6500 a more connected by ethernet to my BT Homehub 3.

  It is I understand that even if there is a wired connection, as long as my iOS device (iPad 2 or iPhone 5) is connected to the same router, I should still be able to see this Officejet thanks to ease of airprint.

  Unfortunately, this is not the case. I get the message "No Airprint Printers Found" on both devices. The only way I managed to get my Mac Pro (Mavericks) to connect has been add to mannualy by using the IP address of the printer.

  Can anyone provide guidance on what I might hurt? Certainly, the printer must connect internet I can print from my iOS devices using HP ePrint app for iOS.

  Some might say, well, what's the problem, just use the HP application, but is not the point. I think that if something has been set up to make things easier, then use it. I chose this printer specifically for this feature is a bit frustrating for her so difficult to get the desired results.

  Hope it is something simple and anyone can help you.

  Thank you

  Steve

  Following this request and reading the many more similar questions, I think I may have solved this.

  I'm not 100% sure but I read a few threads suggests that there are issues around BT Homehub 3 and Hello so this can be a problem.

  I tried the following in the past two days...

  (1) completely don't reset my router (wiped all settings and started)-no luck!

  (2) I tried changing to WPA2 to just WPA security - no luck!

  (3) tried to convey the Hello to the printer ports - no luck!

  (4) turn off the router, printer and all the devices iOS then fed back router, printer, then iOS devices - printer appears on iOS devices, but when printing was selected iOS device returned on several occasions not connected printer error.

  Finally, what seems to have made (at least for now) has been...

  (1) disconnected the Officejet ethernet and set up as wireless.

  (2) off voltage router, printer and all iOS devices then propelled upward in the order listed previously.

  (3) so far, I tried to print a mail and a web page of my iOS devices, and both have been successful.

  By the way I've been struggling also to airplay from my iPhone / iPad until I started messing around with the settings above, and now this question also seems to be resolved.

  Due to the variety of combinations (different printers, routers, etc.) people will have, it seems to be quite difficult to find a solution that solves a single problem but I hope some of my experiences and findings could help others in some way.

• Camcorder not recognized via Firewire.

  My dell precision 370 running xp sp2 worked perfectly to capture video from my sony vx2100 via ieee 1394 firewire, then one day it just would not work. Now when I plug my camera no beep, nothing in Device Manager, nothing. I know that this is not the camera because I have a Panasonic camcorder also in is not in the Device Manager.  Since then, I've replaced the cable firewire and firewire port, but no luck. Could someone please!

  Hello

  1. have you checked if the camcorder works on another computer?

  2. you remember to make changes to the computer before this problem?

  Method 1: Refer to this article:

  Using IEEE 1394 (FireWire) with Windows XP devices

  http://support.Microsoft.com/kb/310433

  Method 2: Why does my computer detect my new USB device when I am running Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

  Important: The Troubleshooting Manual in the link above steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756/