OfficeJet 8730: Scanning Resolution maximum of scanning with ADF for OfficeJet 8730/40 models

Similar Questions

• HP Officejet Pro 8600: scanning on glass OK; scanning with ADF gives a gray line

  Hello

  When I scan a document on my HP Officejet Pro 8600 glass all in one, everything is OK.  However, when I use the ADF for scanning, a gray line appears on the scanned document.  Can I reslove cela to clean something or is this a technical problem?

  Thank you!

  Marc

  Hello there is Marc aka @mk75053 ,

  I'm sorry to learn that when you scan from your ADF file, you see a line on your document. This is usually fixed by clean under the scanner, however there could be other causes. I have the best guide for this type of situation that will show you where clean and give the appropriate instructions. I hope that this rid your question!

  Click here to start: vertical stripes, lines or streaks in the Copies, faxes or Scans

  Please let me know if I can help further.

  Best wishes

• HP Officejet 4632 All in One – scanning with a vertical line through the document.

  Just bought the machine less than a month ago.  Faxes and prints fine and until last week was the sweep for our laptops beautifully... but now is scanning with a dark vertical line up and down the sheet about 1/3 in the document.  What is the cause and how can I "fix" it?

  Any suggestions?

  Thank you

  Hi Rohi63.

  I understand that you have a 4632 Officejet which becomes a vertical line what it is scanned. I'm sorry to hear that, but I'll do my best to help you.

  This seems not only to be the case when using the automatic document feeder, or the glass flat?

  Usually something like this is caused because there is something on the glass. If it only happens when you use the scanner, please get a lint cloth and some glass cleaner (Windex or water if nothing else is available) and wipe the entire surface of the glass for scanning. If this only happens when scanning via the charger, you will see there is a separate strip of glass on the left looking at the scan glass, and you can focus your cleaning there.

  If this does not resolve the issue please try the steps in cleaning several times, but if nothing seems to evolve, please make sure that the printer is connected directly to a wall outlet so that we know, that he has all the power it needs.

  Hope this helps, have a nice day!

• HP Officejet Pro 8500 A909a_ Scan with HP Solution Center does not work

  Hallo.

  My name is Michele.

  I can't use the solution Center HP to scan with my HP Officejet Pro 8500 A909a (I have windows 7 O.S.) because when I click on "Scan document", a white error window appears and says "necessary component is unfounded or not properly installed.". Install new software HP Photosmart". I uninstalled and again installed the software, but it does not work. Previously, he worked with XP. Recently, I updated XP with Windows 7 and I found the solution Center HP does not work. Maybe, it does not match with Win 7?

  Thank you to everyone who wants to help me

  Hi people,

  I appreciate the time you took to try to solve this problem. I was able to do more research and found a useful solution, please click on the link below to get started:

  The HP imaging device is not found... - popup error

  Please try the recommendation and let me know the results.

  Thank you

• OfficeJet Pro 8600 Plus: scans with USB, Ethernet 10 Mbit/s but with 1 Gbps

  I installed my router a Netgear router from 100 Mbps to 1 Gbps router TP LINK Archer C8. I use a printer more Officejet Pro 8600 with scanner. Scanned the fin on the Netgear router, it is not scan with TP link sanner. I get an error "Scanner communication cannot be established. I changed to a USB connection and was able to scan successfully. I noticed the printer only has 10 and 100 a half and full speed duplex settings. The scanner is not compatible with a 1 Gbps puts? I uninstalled and reinstalled several times printing software.

  UPDATE : tried the HP Scan and Capture application in the Windows store. Works very well. Must be some type of problem with the native drivers scan and connections broadband.

• Laser Jet Pro MFP 177fw: cannot scan with Laser Jet MFP 177fw Pro

  I have been using my 177fw Laser Jet Pro MFP on a Mac 10.10 for awhile.  Print, fax & scaning all worked.  I can scan is no longer.  I get the message "the scanner has not completed analysis" (there may be another message before that but it crushed until I read.).

  I use a USB cable for the connection.

  On August 31 I got HP Printer Software Update Verson 5.  What is my problem?

  Thanks for your help.

  Hi @scg117,

  Welcome to the HP Forums!

  I noticed your post about how you can't scan with your MFP HP Laserjet Pro 177fw on your Mac. And I'm happy to discuss this issue scan for you!

  To confirm that the hardware of the printer is functional, you are able to make a copy with the glass of the scanner of the printer?

  To copy:

  1. load the document on the scanner glass according to the indicators on the product.

  2. close the scanner.

  3. on the product control panel, press the button number of Copies.

  4. Select the number of copies.

  5. press the black start copy button or the button color launch copy to start copying.

  Let me know if it works, or if you see another error message.

  If the copy works, then try the steps described in this guide, Scanner USB connection is lost (Mac).

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope this post is helpful!

• The digitized files disappear after that scanning with HP Solution Center update

  The digitized files disappear after that scanning with HP Solution Center update

  Have a HP Officejet Pro L7590 all-in-one.  Under Vista 64-bit.

  Updated my Center of solutions for version 14.  Now when I scan something, it scans OK then when I save to file it away.  Looked on the HP site and found Update critical for this problem, however, the critical update is to version 13 and when I try to run it it tells me I need not and will not continue.

  Also: (maybe something to do with the problem) when using the / opening of the solution Center, when I goes to the buttons "ScanPicture" or "Scan a Document" and then click on "Change settings" there is nothing in the drop-down list for the ' Scan To: ' section.

  Have tried uninstalling and reinstalling several times.  Does not work.

  See you soon!

  Hello

  Two questions actually related to each other.

  Please, try the following:

  Make sure that the HP Solution Center is closed.

  Enter C:\Program Files (x 86) \HP\Digital Imaging\bin and search for the file hpqxmlul.dll .

  Move this file to a temporary folder elsewhere as your office, just to backup porpuses.

  Download and save the following file to your desktop, remove it by double-clicking, a new hpqxmlul.dll file appears on your desktop.

  Move this file in C:\Program Files (x 86) \HP\Digital Imaging\bin.

  Today the launch of the HP Solution Center and test analysis, check any changes with the sweep for list as well.

  Please let me know of any changes.

• scan with ni9401 mode

  Hello, I use the scan mode and the module ni9401, and I'm under codes in labview with a timed loop

  When I try to change the loop timed to dt = microsec and scan period<1ms in="" compact="">

  Compact rio is disconnected! why I got this problem?

  Maybe I can use scanning with scan time mode<>

  Hi, mariomoskis,

  Unfortunately, this is part of the limitation of the scan Mode. You can basically think of scan mode as a train that toured all the modules collects data and it falls on the drive and there is only 1 train for the entire system and it runs at a speed (scanning speed). The fact train one passes each interval of scanning speed, so if you want to produce a train of pulses to a little less than 1 kHz you will get aliasing. However, cRIO should unplug any, I don't know what the problem is here, but it seems closely related.

  There are two solutions to this problem, but the two would require changes.
  1. you can avoid all these problems and the resolution time get down to a 25ns (or less) If you set the mode FPGA. We can use the existing code of NI.com/IPnet to implement a pulse generator to train with the custom calendar settings and pulse on any module.

  2. some modules support digital modes specialized, making essentially a pre-built section of the FPGA code (in scan mode) that support some common functions such as Pulse Width Modulation. With these modules, you can request a rate (which will update at 1 kHz)-specific, but the actual timetable for the module is managed at the hardware level. There are only a few modules that support it, and they are listed in the link below.

  KB 55L06EMO: what Support Modules of the series C, specialty digital functions in Scan Mode?
  http://digital.NI.com/public.nsf/allkb/2664A3D35D9F79A4862576B300277E35?OpenDocument

  I hope this helps.

  Saludos!

  Jesus

• HP Director does not scan on XP software, how to scan with the office Professional 2007 programs?

  HP Director does not work on XP, I contacted HP several times with no fix. When I try to run Director nothing happens. Is there a scan inclued application under XP or office Professional 2007 can I use or downloads of microsoft? Office 5505 HP all-in-one. XP pro.

  contact to the * Email removed for privacy *.

  Hi MONTEHOUSEMAN,

  You can check if you have followed these articles of HP.

  The HP Director no window open in Windows XP HP Officejet 5505 all-in-One Printer

  Scanning with HP Director in Windows XP HP Officejet 5505 All-- One Printer software in

• HP Officejet Pro 8600 more e-all-in-one printer - N911g face 2 of copy or scan on adf?

  I just want to know if HP Officejet Pro 8600 Plus e-all-in-one printer - N911g can do 2 copy or scan on adf faces?

  Thank you.

  Hello

  Based on this, it can:

  Improve productivity in the office with this all-in-one performer who offers vibrant prints and marketing without borders
  materials. You can count on professional color documents for up to 50% lower cost per page per report
  with lasers.1, tap the touch screen to easy-to-navigate to access applications and print from the web without a PC2 - or
  print from virtually anywhere with HP ePrint.3 Boost efficiency in your office with Ethernet and wireless
  connectivity, 4 automatic two-sided printing, an automatic document feeder 50 sheets (ADF) and digitization of glass to the top
  legal - size.5

  Kind regards.

• Not able to do a scan with Microsoft InBox Driver

  Hello

  I am not able to do a scan with the Sub parameters of analysis, using Inbox Driver Scanner Scan & Fax application in vista PC [32bit_Vista X 86 SP2] client (WIA 2.0)

  Source: Feeder

  LongueurSource: A4

  Color: gray

  Format: XPS

  Resolution: 100

  The same combinations work with the driver supplied by the manufacturer, but with the drivers Microsoft InBox, I am not able to do a scan with this combination.

  I was getting the error message below "ERROR applying settings to Driver".

  Kindly let me know, it of because of a inbox driver or not.

  If yes give me your comments on this to solve.

  If there is no problem with the driver supplied by the manufacturer, by all means use this driver instead of the Microsoft Inbox driver (whidh is perhaps not as common or may have other issues).  If the other driver has resolved the problem, then be happy that you have a solution and use it.  Forget the driver that does not work well and just throw it away.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Not able to scan with the preview after upgrade from Mac OS Sierra...

  After upgrading to Mac OS Sierra. I'm unable to use the preview to scan.  Before this upgrade, it worked fine.  The HP scanner software does NOT work something like OS 10.8 or 10.9.  Preview worked perfectly so far.  If anyone knows how to solve this problem, your contribution will be greatly appreciated.  Thanks in advance.

  Have you tried scanning with Capture of Image instead? It worked for me.

• Hi all, I keep is typed in the password at startup box, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Hi all, I get a storm of +'s typed in the password at startup box upward, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Clings in the key on the keyboard? Wired or wireless keyboard?

  Try to run this program, copy and paste the result in a response. The program was created by Etresoft, a regular contributor.  Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.

  Etrecheck - Information System

  Reset an Apple Bluetooth mouse or Trackpad wireless keyboard (pairings and other common troubleshooting problems)

  Restart your computer, hold down the option/alt - P - R keys command before the gray screen appears. Continue until you hear the startup chime for the second time.

  Reset the NVRAM EXTRA memory

• After the update to firefox 17.0 when I do a scan with Norton 360 it does not pick up the tracking cookies which changed 16.0.02

  After the update to firefox 17.0 when I do a scan with Norton 360, it is no longer captures the rejected. These cookies that have been picked up with firefox 16.0.02 what you have changed? Plus, I'm getting sick of these updates - at least we tell users what has changed in new versions.

  First of all, we do not say what has changed in each version, http://www.mozilla.org/en-US/firefox/17.0/releasenotes/.

  Secondly, Norton should always be able to delete your cookies (just so that you know that the cookies are generally harmless, and you don't need to worry to remove). If not, you can delete the cookies in Firefox Cookies - Information that Web sites store on your computer

• Can't scan with HP LaserJet MFP M127fw Pro

  I have installed the printer driver and tried to follow the instructions in the manual to scan a document.  When I find my printer folder in the start menu/all programs, there is no option to scan. Help!

  Hi @3Digit .

  I see that you are having problems of analysis, it is not any scanner in the HP folder software. I would like to help you today.

  Open the HP scanning with one of the following methods: