OR-scope disconnect routing BUG?

Similar Questions

• E1200 Cisco Connect update fails

  Ran CiscoConnect.E1200.1.4.12263.1.exe on laptop twice and returned the same ' it there a problem result.»  Disconnected router power for a few minutes between the two.  The current version is 1.4.11200.0. My office is also connected by cable to my modem broadbandcable.  Not the biggest problem, but any ideas?  Firmware is up to date.

  (btw, the copy under the details seems to send a tiny image, if it sends whatever it is in the Clipboard).

  

  Reset the router. To reset the router, push the Red reset at the bottom of the unit for 15 seconds. Wait a minute, and then rerun the Cisco Connect software.

• RV042 stopped working

  Hello

  I have the following problem:

  My rv042 stopped working after about two weeks.  The configuration looks like this:

  Belkin Wireless Pre - N in bridge to port 1 mode

  -RV042 1 computer connected to port 2

  -Cable modem Internet

  -DSL Modem in bridge of dmz mode

  * The router works with the embedded firmware, it's never been flashed.

  Everything worked very well for about two weeks and then suddenly stopped working.  I used the system in time.  Things just disappeared.  I tried the following:

  * manually Computer Configuration to an IP address on the network instead of DHCP

  -No connectivity. Failed to contact the router at all.  Cannot ping it.

  * Power/disconnect router and wait 1 hour before feeding this back.

  -No connectivity.  Failed to contact the router at all.  Cannot ping it.

  Perform a reset of the modem

  -No connectivity.

  * Perform the reset of the modem. Reconfigure the computer.

  -No connectivity.

  * I tried with several computers.

  * I can connect the computer directly to a cable modem and internet access.  Cable/internet is so direct.

  * When computers are not assigned an IP address in DHCP mode.  Running "ipconfig / renew" cmd prompt fails with timeout.

  * When configured manually, I cannot ping the router on 192.168.1.1

  * No warning on the router light.  All the lights seem to be good.  When it is connected to the Lan 1 and Lan 2 lights flash constantly to any interval of 1 second.

  Can anyone think of anything to try with this?

  Thank you.  I managed to solve this problem by taking the following steps (found on another post here):

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) connect a computer cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.

  (11) reload saved config.

  (12) connect 1 modem at the same time and make sure they connect to the routers statuspage.

  (13) connect one computer at a time until all are connected.

  I never found a cause of this accident.  I turned more connection on the router in the hope I can find a cause if it happens again.  I hope this answer will help others.

• HP Photosmart 7525 unable to connect to web services when you are trying to scan to e-mail

  Hello

  Having the same problems as everyone else.  The disconnected router and printer.  DNS manually changed to 8.8.8.8.

  Attempt at analysis of the printer.

  Thank you

  Allow to set the printer to Factory Defaults and reinstall again.  Try now.

• What is the problem with 'AttributeMap' in a name of trigger?

  I think I found a bug in SQL Developer, but being new to this I thought I would ask here everything first see if anyone else knows why the error occurs.
  
  I use SQL Developer to write and test my table, the sequence and trigger scripts to create an application that creates the company I work for, but I ran into a problem where one of our names to trigger system, "TRG_ATTRIBUTEMAP_ID_INSERT" is originally a series of terrible mistakes that forces me to restart SQL Developer whenever I run the script. the table and the order are created very well however. If I change the 'P' to a 't.' in the name like "TRG_ATTRIBUTEMAT_ID_INSERT" Yes, the script works fine.
  
  Also, if I take the unaltered Create statements outside the lines Execute Immediate and run through SQL Plus, the trigger is created very well.
  
  Here is the error report I get:
  
  Error report:
  ORA-00603: ORACLE Server Session concluded with fatal error
  [ORA-00600: internal error code, arguments: [kqlidchg0], [], [], [], [], [], [], [], [], [], []]
  ORA-00604: an error has occurred at the SQL level recursive 2
  ORA-00001: unique constraint (SYS. Violated I_PLSCOPE_SIG_IDENTIFIER$)
  ORA-00942: table or view does not exist
  00603 00000 - "ORACLE Server session ended with a fatal error.
  * Cause: An ORACLE Server session is in an unrecoverable state.
  * Action: Connect to ORACLE again if a new server session will be created
  
  
  Here is the script I'm writing:
  
  DECLARE TABLE_MISSING EXCEPTION;
  PRAGMA EXCEPTION_INIT (TABLE_MISSING,-942);
  BEGIN
  BEGIN
  RUN IMMEDIATELY 'TRUNCATE TABLE AttributeMap;
  EXCEPTION
  WHEN TABLE_MISSING THEN
  BEGIN
  IMMEDIATE EXECUTION
  'CREATE THE AttributeMap TABLE '.
  (
  ID NUMERIC (38) NOT NULL
  -column removed to identify the error.
  CONSTRAINT PK_AttributeMap PRIMARY KEY (Id)
  )';
  BEGIN
  FOR (IN) cc
  SELECT sequence_name got sequence_exists
  Of all_sequences
  WHERE sequence_owner = USER
  AND sequence_name = "SEQ_ATTRIBUTEMAP_ID")
  LOOP
  -sequence exists, drop it (at least there will be one sequence)
  RUN IMMEDIATELY 'DROP SEQUENCE SEQ_ATTRIBUTEMAP_ID;
  END LOOP;
  -create sequence
  IMMEDIATE EXECUTION
  'CREATE THE SEQUENCE SEQ_ATTRIBUTEMAP_ID.
  MINVALUE 1
  MAXVALUE 999999999999999999
  START WITH 1
  INCREMENT BY 1
  NOCACHE';
  END;
  IMMEDIATE EXECUTION
  ' CREATE OR REPLACE TRIGGER TRG_ATTRIBUTEMAP_ID_INSERT
  INSERT BEFORE on AttributeMap
  FOR EACH LINE
  BEGIN
  IF: new. ID IS NULL THEN
  SELECT SEQ_ATTRIBUTEMAP_ID.nextval IN: new. DOUBLE ID;
  END IF;
  END;';
  END;
  END;
  END;
  
  
  I'm relatively new to Oracle, so I expect many of you wonder, ' why are you doing it like that? If you know a better way, I'm all ears, but I still want to know why a name of trigger with AttributeMap in it causes such problems.
  
  UPDATE: I tried to change the other letters in the name of the trigger and found if I change one of them it seems to work correctly. So is reserved TRG_ATTRIBUTEMAP_ID_INSERT or something?
  
  Published by: Paul Laska on August 1, 2012 14:10

  Hi Paul,.

  Here is some information about the PL/scope function which became available in Oracle DB 11.1:

  Oracle® Database Advanced Application Developer's Guide
  11g Release 1 (11.1)
  
  PL/Scope is a compiler-driven tool that collects data about identifiers in PL/SQL source code at program-unit compilation time and makes it available in static data dictionary views. The collected data includes information about identifier types, usages (declaration, definition, reference, call, assignment) and the location of each usage in the source code.
  
  PL/Scope enables the development of powerful and effective PL/Scope source code browsers that increase PL/SQL developer productivity by minimizing time spent browsing and understanding source code.
  
  PL/Scope is intended for application developers, and will usually be used in the environment of a development database.
  

  Of course the desired SQL Developer Team enjoy it in our Editor Code PL/SQL and DB Search, even in the version 1.1.x releases, by default the SQL Developer both the PLSCOPE_SETTINGS of IDENTIFIERS: ALL.

  Unfortunately, PL/scope had a bug which, long story short, effect triggers. This question, followed in bug 10094416, has been backported fixed and even to patch the many versions of database 11.2.0.x on various hardware platforms. If your solutions are:
  1 solve the problem by applying a patch for your version of the database.
  2. the solution of the problem using IDENTIFIERS: NONE for the sacrifice of some code editor in Chief/Research (not exactly how).

  -Gary

• Wireless router is disconnected from the PC (s) during the use of Firefox 37.0.1

  This problem occurred for the last 2 weeks whenever I use Firefox on each of the 2 PC's I use it every day. The problem may occur a few minutes after the start of Firefox, or it may be hours of continuous use before the connection is lost. It's okay if I'm in Firefox by itself or have the background applications running, but without a doubt requires Firefox runs before I see a problem.

  Configuration: WIN 8.1 and VISTA 64. the two latest updates.
  LAN: cable modem and Belkin wireless router; together with the latest firmware.
  Firefox v37.0.1 without add-ins or modules. Start page is 'empty '.

  Symptoms:
  Status bar Windows shows that I'm disconnected from the router.
  Router and the modem status LED shows that I am connected to the internet. Same thing for the VICTORY of the network status app. It shows no connection to router.

  The problem can be temporarily fixed by power cycling the router. Or, in the meantime just a random delay the connection may (or may not) be restored on its own.

  I also use a standalone PC application that streams the text given in short bursts and runs all day (no video or music... just short lines of text) with no problems until I launch Firefox in the background. Then he can go a few hours before the connection to the router is lost. I also often watch videos on my Tablet without the router problems. While typing in this issue on a PC I was disconnected from my router. I'm hoping to get some suggestions as to what to inspect or modify. Thank you!

  Fred, I had to leave the House early this morning and had no time to dig a cable long enough to reach my modem to try your suggestion. But, what I did was half of your suggestion. I pushed the reset bit recessed on the modem and left the House around 08:30 with Firefox running on both computers. Seven hours later everything is normal. No router disconnects and I gave a very good workout system.

  I have also now initial notice that connects to the web sites are faster.

  It is obviously a logical explanation for what was going on, but to an outside observer (), I see absolutely no logical link to the 'solution' for the rest of the universe. I won't lose sleep on. And I'm going to ask you more specifically when the next puzzle problem occurs! Thank you, Fred!

• Satellite A500 - 17 X frequently disconnect the router wireless - weird

  Had this problem since I bought the laptop about a month ago. It connects very well to our wireless (full signal, speeds), but sporadically disconnects for no apparent reason. When I try to reconnect, the signal passes of five (full) bars up to three bars and it won't let me log in again, no matter what I try. When I click on it it loads just for a while and then said it was impossible to establish a connection. Troubleshooting / repair does nothing. The only way to fix it is to pull the power on the router and then plug it in again, resetting the connection.

  It seems that this is a problem with the router, but I have tried in other houses and it does exactly the same thing on the connections of others. Other devices are still able to use the connection after mine died. My laptop and install broadband (Virgin Media) are only one month.

  I tried to install the WLAN drivers on the toshiba site, but it changed nothing.

  Someone can think all possible solutions before you give up and take it back to the shop?

  See you soon.

  You have successfully updated the WLan driver?
  I guess you used this Toshiba WLan portal page to download driver:
  http://APS2.toshiba-tro.de/WLAN/

  Here's the latest drivers.

  I recommend updating the BIOS as well.

  Check it!

• Router disconnects Internet duringWindows download

  Question is interesting

  Earlier when I download torrents, internet connection would be lost. I first thought that my ISP didn't like what I was doing and they were etc. Router must be manually restarted because it works again.

  In any case now, the router will disconnect when windows update download begins. If I stop windows download and restart the internet router is back to normal. I can't explain and you will notice that people have reported this in the past but were not answered.

  We hope to get useful information.

  see you soon,

  Hello nJose

  Have you tried to lower the MTU level?

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24015

  DarrenM

• Satellite L25-S1192: WLan disconnect when moving from router

  I looked in the nets, and I can't find an answer to my exact problem.

  I have a laptop Satellite L25-S1192 and XP running.
  My problem is the Wi - Fi works very well until I'm 10-15 feet away from the router.

  Once I get beyond that point, I lose the connection even if when I display the network connections it shows that I'm still have an excellent signal and always connected. Other laptops work in the House and I did several other tests to rule out the router.
  I updated the driver but nothing seems to help.

  Given that the connection is working near the top which tells me the settings are correct.

  What Miss me?
  Any help is appreciated.

  Hello

  In my view there is nothing wrong.
  The WiFi signal seems to be too low and therefore the WiFi disconnects.

  I think that this happens when you run Notepad with battery operation. Right?

  Well, you can go to Device Manager-> properties-> Advanced tab Wlan card
  There you can check if the WiFi network is set to mode harder

• Have to disconnect/reconnect to the router

  I have a clear-cut problem: occasionally, about once a day or two, suddenly I can't load a web page. I can always solve it to disconnect and reconnect to the network, even if it shows me as connected (with five bars).

  Based on the other computers in the House, I concluded that the router sometimes has a little problem. It shuts off and then on again. Reconnect automatically other computers (ASUS victory 8 machine and my Nexus 7), but mine does not.

  Any ideas on how to solve this problem?

  Thank you

  Al

  Al
  
  TouchSmart HP Envy 17
  Windows 10 worm 1607

  It turned out to be a bad cable modem, which had problems when Suddenlink updated their system. New modem and no problem.

  Thanks for the help.

• When you transfer files to the internet, the router disconnects from the internet, but the network remains in tact.

  I have a wireless router Belkin g with 1 Server 2003 cable and 2 xp machines and 1 machine vista wireless. My problem is when you transfer files to the internet, the router disconnects from the internet, but the network remains intact. I cannot remote in all computers, but not internet. Once I have restart the router, everything works fine. I was wondering if anyone else has had this problem and how to fix them.

  original title: problems with the router.

  I have no solution for you.  It seems more likely to me that it is a hardware problem - but if it was related to traffic, I would expect that the problem on the downloads more downloads.

  In addition to DSL reports, you could try to ask some of the forums that specialize in the updated firmware for wireless routers.  This is not to say that you need to install the modified firmware (although there may be good reasons to do so), but people who do usually firmware mods are much how the equipment works and what might be its potential failure modes.

  Is one of the best-known sites DD-WRT.com, but there is one list of other here: http://en.wikipedia.org/wiki/List_of_wireless_router_firmware_projects the firmware on these sites was originally designed to run on Modem Linksys WRT54G, but applies generally to Linux with chips Broadcom - based wireless routers and DD - WRT claims that its firmware takes care of some Belkin routers.  If your router is one of those on what DD - WRT will work, there will probably be someone in the forum there will have something for you.  See the list here: http://www.dd-wrt.com/site/support/router-database

• Annex WAG160N has v2 ADSL2 + Wireless Modem Router disconnecting at random intervals

  The problem is that my WAG160N router v2 isolates at irregular intervals for no clear, obvious and clear reason. The router always reconnects to the Internet automatically, but we want to have stable internet connection so it does not interfere with our download and my game online. Sometimes, it will be disonnect once a day, two days, three days or more times a day.

  This problem occurred for about nine months and we have tried to solve this problem for four months without success and very little progress.

  There are nine devices connected to this router:

  Desktop Mac (connected by an Ethernet cable)

  MacBook Pro my mother (wireless)

  My mother of Windows (wireless) laptop

  My Iphone (wireless)

  My mom (wireless) iPhone

  Our Ipad (wireless)

  Our printer (wireless)

  My Xbox 360 (connected by an ethernet cable)

  My PS3 (connected by an ethernet cable)

  First of all, I contacted our ISP. They conducted tests on our phone line and there was no obvious abnormalities. They then made some adjustmenets to our connection, but none of the improvements to our stability of connection, either. I also did the isolation test which did not help. Then they came to the conclusion that this router is the source of the problem.

  Then I noticed that when my Internet was disconnected we had active DHCP and it kept more than one of our devices, assigning the same IP address. On my desk he showed me an IP address conflict message whenever we have disconnected from the Internet. So I disabled the DHCP and manually assigned each device to their own individual IP addresses static. This has not fixed my problem even if there are more conflicts of IP addresses.

  Then I tried to connect my computer directly to the WAG160N v2 via an ethernet cable, but each single device is always give themselves up randomly. Therefore, we have established that this problem occurs with the cable connections and wireless.

  After that, I did some research on the Internet and made a lot of adjustments and modifications that do not stop this problem.

  These including: lower the MTU to 1365, changing to channel wireless channels 1 and 6 (we were on channel 11), using a standard instead of a wide channel, lowering the keep alive - redial period from 30 seconds to 20 seconds, increasing the Redial period keep living to a maximum of 180 seconds, disable UPnP and disable the DHCP server on the router configuration page.

  I have same Access Restriction is turned off.

  I also checked with my ISP and we use the correct settings of Encapsualtion, multiplexing and Virtual Circuit.

  So I thought I would post here because we really need to have this fixed a problem and we do not know how. I can't find the logic of why this is happening. This problem shouldn't be complicated.

  Any help would be appreciated, thanks.

  My Internet has not disconnected for a week.

  Without reset and reconfigure my router, I did the following in the advanced wireless settings page:

  Reduced from 100 to 75 beacon interval

  Lowering of the threshold of Fragmentation of 2346 to 2306

  Lowering of the 2346 to 2304 RTS threshold

  I found this info from a different thread.

  I'll post again less than a week and if my Internet connection is always stable, I will mark this message as my solution.

• Linksys router WRT160N v3 warning disconnect and reconnect

  Hi all

  I know that you've all probably seen this thread before. (I know I have).

  I have a WRT160N v3 Linksys router and it keeps disconnect them and then reconnect. It disconnects wireless only. LAN still works fine.

  I tried many different methods to solve this problem, but none does not seem to work.

  I'm very disappointed with the quality of the product. He did everything since it was purchased. I personally would have sent in for repair, but others in my household would not have agreed to that.

  Additional features:

  -Firmware Version 3.0.03 (no later than as of July 2010)

  -A a SSID set to broadcast

  -A encryption WPA2-Personal

  -Mixed-mode network

  -Width of the channel set to Auto (20 MHz or 40 MHz)

  -Channel set to Auto

  Please help me solve this problem.

  Thank you in advanced.

  In my view, that it is corrected. I'm using dd - wrt firmware instead of ciscos

• Bug of Linksys WRT54GC Mode of operation of "router"?

  I use a Linksys WRT54GC router and I experience a behavior that I don't expect.
  You give me your opinion?
  This is the case:

  My assumption of "Gateway" or "Router" operating Mode is:
  Gateway mode means NAT that makes invisible LAN subnet side WAN addresses. NAT is disabled by activating the Mode of operation of 'Gateway' to 'router '.

  I have connected a PC (192.168.2.100) to port the router WAN and another (192.168.23.100) PC on a LAN (192.168.23.1) of the router (192.168.2.2) port.
  When I switch my WRT54GC "Router" mode I can't always ping the PC on the site of the side router LAN WAN. SPI Firewall protection and block anonymous Internet requests are disabled. Firewalls on both computers is disabled.

  I saw a similar problem at the forum "Connecting two routers via WAN" 08/28/2008 Victor Tang.

  Don't you think that it is a bug in the mode of operation of the WRT54GC software?

  I reported the bug to Linksys.

  My first experience with Linksys technical support is very good.

  They take the serious problem, ask for the discharge of Wireshark and send me an update of the firmware of the router.

  This fixes the bug with the mode of operation, now I can without NAT on and outside, very well!

  I don't have firmware update earlier because the release notes did not mention my bug, I read in the forum a lot of users having problems after the update of the firmware, so I followed the policy do not update unless it can solve your problem.

  There are some things perhaps worth mentioning:

  You should be careful to use the right firmware for your router.

  Not only the model of the router is too important, the hardware version and too country!

  I've got a WRT54GC, hardware version 1, and it is the type of the EU.

  Of this material, there's also a different US with versions of firmware version!

  The latest version of the firmware to the US type is v1.60.1, the latest version of the EU type is 1.60.0 v.

  Thus, you should take care of this website, you download the update to get the right version and read the release notes. These release notes, you can check if your current firmware version is part of the history of this firmware, so you know that you have the right one. I was so very accurate because many have reported problems in the forum with updates.

  Now I'm able to Exchange traffic between computers and printers in different subnets and I can access the Internet from each subnet gateway I want.

  It is important to think about the configuration of your PC and routing tables.

  The firewall on the computers must be configured on the additional subnet.

  A PC has a default gateway to reach a device on another subnet.

  Most of the time these are devices on the Internet, so if you create additional internal subnets that your traffic will be by default will be send to the Internet and will be lost. To define additional gateways where your additional subnet can be found to avoid this.

  This can be done on a PC with the command: route add (IE 192.168.23.0 mask 255.255.255.0 192.168.2.2) or you define a static route to your router (the latter is preferable).

  The problems I've had, forced me to consider how does networking, with the help of the users on this forum, I would conclude that this is a bug, with the support of very good Linksys everything now works as expected.

  Thank you.

• random disconnections for my wrt54g2 V1 router

  This had happened for a few months and I didn't really mind until it disconnects worsen.

  usually, when I turn on the router and started using the internet, it randomly disconnects once. My Wireless SSID will disappear and loss of the connection. and no matter how I update the SSID will not yet be released.

  the only way to regain internet access is to re - feeding on the router, if the SSID will be broadcast again.

  My wrt54g2 V1 router had recently upgraded to the latest firmware version, 1.0.04)is.  but still disconnects as usual.

  However the disconnects happen only once, after u re - turn on the router, you will not cut again.

  but after turning off my laptop and use it again a few hours later, the same thing happens again, a random disconnection and got to re - feeding on the router...

  can someone help me on how to stop the disconnection of the router?

  Thank you.

  Kind regards

  Leon

  Try the following settings as well as in the router for wireless connectivity:

  # Open the browser and in the address bar type 192.168.1.1 which will open the router configuration page.

  # Bring back the MTU (Maximum Transmission Unit) of 1500 to 1400 or less (usually found on the main page / basic configuration of your router). Here is the link to determine and implement the right size MTU: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=fbf8e8564632422eaa8ea80bf9dcba64_386.xml&pid=80&re...

  # Click on wireless tab select the channel wireless at 6, 9 and 11. Click on save settings.

  Settings wireless #Adjust the following:

  ~ ~ Reduced from 100 to 75 beacon interval

  ~ ~ Lower the threshold of fragmentation of 2346 to 2306

  ~ ~ Lower 2347 to 2307 RTS threshold

  Then reconnect to the wireless network and then check the connectivity status...