parallel port of LabVIEW

Similar Questions

• LabVIEW and parallel port

  I'm trying to control a motor of OMHT23-400 with a motor drive 3540 M using a Moschip PCI Parallel Port. I created a program to send impulses alternatilng the engine and make it run a desired amount of degrees. The motor in my computer address is/o series BD00-BD07. The same program worked in another computer that has address of the parallel port was Beach e/s-0378-037F. I don't know why, the program operates in the first computer and the same program will not work in this one. Thank you for your help.

  PS: the program I wrote is attached below.

  Guillermo Naranjo

  Physics/Space Science

  Florida Institute of Technology

  Phone: 768 537 6392

  E-mail: [email protected]

  A search will produce a lot of results. For example:

  The use of VISA to access the Parallel Port in LabVIEW

  To access parallel Ports with VISA

  Using the LabVIEW Parallel Port (Note that the images of the document can't be - it must be fixed by the web site manager OR).

  Parallel communication Port (it's just the VI provided the first KB article re-recorded for more recent versions of LabVIEW.

  ...

• Parallel port on Windows 7?

  Hi all

  I'm trying to migrate some older software (LV and otherwise - all internal written anyway) who communicates via the parallel port on a Windows 7 (64-bit).  The GPIB based programs all work fine, but I can't find a way to talk to the parallel port.  The machine (HP Pavillion Elite) came without a parallel port, but I found a card PCIe (Startech PEX1P) which adds the value 1.  It appears in the Windows Device Manager, but the address of the resource is listed as D010 rather than the old 378, and it cannot be reconfigured (the folks at Startech says Windows actually assigns the address).   Any suggestions?  Anyone try this yet?

  Thank you

  Michael Tracy

  Synergy microwave

  I know this is not guaranteed, but following the actual signs, I (finally!) got the Startech PEX1P card to operate!  Instead of using the Port.VI, I tried to use VISA you writing again, but this time, I updated the land of terminals 11 and 12 by the document OR on the use of the Parallel Port in LabVIEW.

  Michael

  Dennis Knutson says:
  Even functions in new versions of LabVIEW with the correct representation for the address lines is not guaranteed to work on your OS and 7.1 is not supported at all. The AccessHW dll must also be written for the OS and it will not happen. I say LabVIEW upgrade and use VISA or stick with an older operating system.

• I'm waiting times tries to access a parallel port with VISA

  I get VISA time-out errors when you try to write to the parallel port. MAX said that the port works and I should be able to communicate with him. Device Manager Windows 2000 also said that the device works. I use writing to the parallel port with VISA example I found on the site of nor. To make it even more confusing (or), it runs on one computer but not another. All software and drivers are the same on both machines. On one who gives me the error of time-out, I am able to write to the parallel port using "accesshw".

  What a coincidence. The computer that I had problems with is also a Dell Optiplex. The pins of wiring together the way that you have specified has solved my problem of timeout. The cable I got with just bad has terminals 11 and 12 low attached as indicated on the page with a link to the code sample titled "with the help of VISA to access the Parallel Port in LabVIEW" I know why the original cable worked with a bridge but not a Dell Optiplex. Thanks for the quick fix!

• LabVIEW control LCD by PC parallel port

  Hello world! I'm a beginner and I have a project, control the parallel port on LCD 16 x 2 thought. I wrote a program (not yet order RS and RW E wirtten). Would you please see, is it right or wrong? And could help me to complete it or which could sent me a code on this subject (my email: [email protected]). .
  My conection material: 2-9 pins (of parallel 25 pins) conect with D0 - D7 (of the LCD screen), pin RW as GND. 14, 16 pin port parallel conect RS and E of the LCD. Please help me. Thank you. Funny!

  This link my program:
  http://www.YourFileHost.com/media.php?cat=...file=LCDLPT.rar

  
  

• The use of pins of status (4 outputs) and data (8 entries) of the parallel port pins at the same time.

  Hi all

  I'm a newbee in labview. As part of my project work, I need to get 8 digital inputs and send 4 digital outputs.so I think to use the Parallel Port on the pc.i can make use of 8 datalines for entries. I found the site NOR is it possible to use status for output pins. But is it possible to use status for output pins pins and data for entries to the time.please help even me also mention of the measures to take, or keep in mind while implementing.also include any example vi that could be useful.

  Thanks in advance

  I would recommed you to NOT use the parallel port. Now a day you have hardly a PC with parallel port. also if you have some old PC then most likely last version of LabVIEW (e.g. 2010) will need a lot more memory RAM and processor.

  If you want a solution very very low cost then I would recommend using an arduino to that effect. You can then download LabVIEW Interface for Arduino and start working.

  If you continue to use the parallel port, then you could try (I haven't worked with parallel port and have not tested the following solutions)

  Download VIPM and then install the enclosed package. It will add the port e/s palette in your labview. and you can use it.

• Press the button on parallel port signal to trigger a process

  I just need to connect a pushbutton on the parallel port to set it as a signal of the beginning of a process.

  When the button is pressed, labview runs a process.

  Kindly help me how to do this, the prayer of wiring

  Lines of data to use as input Some parallel ports can be configured for use as inputs data lines. This depends a lot on how the manufacturer has designed the parallel port. With some models the data lines can be read in the same way that we read the lines of control, leading them to logic high, so they will take the value of an external signal. However, most parallel ports require that you set the bit of sense for entry. It is bit 5 of the control register (base + 2). If the port is capable of it, setting the high bit for effect to sort of lines-State so it can be driven on the outside. Sometimes it is also necessary activate the 6 bit high or low. However, it is noted that some manufacturers actually block those bits so that the software can edit them. An example is shown below in Figure 7.

• Re: Tecra M11 - 15W - Parallel Port LPT1, not found in Device Manager

  Hello

  I have Tecra M11 with PA3680E-1PRP Docking Station. BIOS Version 2.9.

  Problem is, I want to use the Parallel Port LPT 1, but in anchorage additive dosent device manager there.

  Thanks much for the tips

  Hey Buddy,

  What device is connected to the LPT1 port? Usually if you connect a device to LPT port and you turn on you will be asked for drivers. AFAIK the LPT device drivers must be installed before connect you.

  Several years ago I also used LPT connection for my printer but one day it didn't work. The problem was only a defective cable. I replaced it with a new one, and then the connection to the printer has been recognized again correctly! :)

• parallel port does not have the protection key

  I just bought a terca M2. When I try to install a software that uses a hardware key (small connector in the parallel port) I get the message that he found no protection key. I have installed this software on other laptops (also with xp pro) and they are all worked well.
  I also tried two parallel port settings, but it still does not work.

  Please help me solve this problem, otherwise, this laptop will be useless to me.

  Hi robert,.

  have you checked that the chip set driver in Device Manager? As far as I know the parallel port is controlled by the entire ship!

  Have you checked if the parallel port in your M2 works without any problem (for example, a parallel printer) to exclude a defect of material! If there is a material defects you might bring the laptop to a Toshiba service for a short health check partner!

  Hans Bye

• HP Pavilion p7-1026 b: parallel port

  I recently bought this computer used for a CNC machine by computer I am building. I need to install a parallel port so that it works correctly.

  I bought this port parallel http://www.pmdx.com/2PARPCI , and it does not seem to adapt to any location. He really did give me 2 ports.  Can you advise me on which one to buy. Or an adapter to make this one work. Looking at the pins on the motherboard of the PC it seems that the slot is back on the mother. Or the notch is on the wrong end.

  Thank you for your valuable time.

  You are the very welcome.

  Unfortunately, I have never installed one myself.  All my HP computer business came with parallel port cards.

  I take one in the list I posted and get the best market with the best / most of the critics.

  Wireless... I do not use the internal wireless cards.  Had too many problems with them.

  I use this external dual-band USB wireless network adapter on my HP 3 business desktop PC.  Works fine on W7 - W10.

  I used the W7 drivers that come with the disc for the W10.

  https://www.Amazon.com/Linksys-dual-band-Wireless-N-adapter-AE3000/DP/B007ZLGXA8?th=1

• Parallel port has stopped working on my A30

  I have an A30 with Win XP pro sp2. Recently disappeared from my DVD player and also my printer has stopped working. I reinstalled DVD Tosh tools and it is now working again, but I am unable to get the parallel port works again. I have it active in the Bios (worm 180.) and also in the control panel. He started to drive me crazy.
  Is there a tool to test the Lpt1 port or someone else has found a solution to this problem?

  Hello

  If does not work reinstall the drivers, I think you should try to recover the entire system. But don't forget to backup your important data. Sorry I can't give you better advice.

  Good bye

• HASP dongle (parallel port) on the A100-906 Satellite connection

  I need to work with Solid Works software. It is protected with HASP dongle which should be connected to the parallel port (printer port). But there is no such port on my Satellite.

  What can I do?

  Several ideas of spring in mind:
  -try to get your software vendor to replace your dongle with a USB version (possibly you will get a free)
  -get a parallel converter cable / usb (not guaranteed)
  -get a parallel PCMCIA card (a bit expensive...)

• Satellite M60: Need a parallel port to connect the Iomega Zip drive

  Hi guys,.

  I have a Satellite M60 and I want to transfer files from my Iomega Zip drive.
  My laptop is not has a paraller port, so I bought a converter to operate, but there was no result.

  Is anyone of you know how to solve the problem and finally reach my driver ZIP of my Satellite in order to transfer files?
  Do I need another converter?

  If so, when is? Or do I have to buy a PCI card with paraller port?

  Any response will be appraciated

  thanx

  Hello

  I've never used a converter USB / parallel but a USB-to-serial port converter and I had very bad experience of such pieces of witch.
  AFAIK this adapters don't work properly.

  Therefore, your suggestion is not bad to use the PCMCIA card with a parallel port.

  Check first of all in your user manual what cards are compatible, then you can try to use this card.

  I think it would be the best solution to connect your Iomega Zip drive to the M60 laptop.

  Concerning

• Pourrait PARALLEL port added to the Satellite Pro M40?

  Dear toshiba
  I have sattelie Pro M40 with room for a parallel port, the port can be added

  Kind regards

  Hello

  As Kevin says you can t add a parallel port, but you can use another device like PCMCIA card with parallel port.
  Check this box:

  http://www.IECI.com.au/products/Product_Page2.asp?product_id=113

  Good bye

• Satellite A200: How to connect a parallel port printer?

  Probably a very stupid question, but I would like to connect laptop series A200 on a parallel port printer that does not have a USB port... What is the best option?

  Hello

  You ask the best way?
  Well, you have only one way?

  You need an adapter USB to parallel. Check in google for certain offers.
  I searched in google and found some good options.

  Perhaps this might be a good choice;
  http://www.ramelectronics.NET/HTML/usb_printer_cable.htm#UP6C

  Best regards