PCoIP WAN access

Similar Questions

• E4200: no WAN access, can't Flash firmware

  Hey all,.

  I got my E4200v1 by yesterday and the installation was easy enough... Apart from two problems:

  1. He's not through an internet connection. I use a de Vigor120 ADSL2 modem that connects to the internet just fine. When I plug in the router and a wired / wireless, I can't access the web.

  Then, I put the modem to use the router as my DMZ. The E4200 correctly displays my WAN IP in State and gateway/DNS to my ISP servers. Still no internet access.

  I am sure this should work (or the router is broken)... Please advise! 

  02:02 hours of head, tremors, I tried to update the firmware of the router. 1.0.04)is will fail as soon as it downloads. The DD - WRT build from the wiki page fails as soon as it downloads. I always do a 30/30/30 reset before each.

  Any ideas? I'm at the limit of my understanding and experience. The next thing this router is returned... Something I've never had to do before! (Also, I bought in Australia if it makes a difference).

  Thanks for any input

  mafro

  Edit: I'm working on the assumption that 'v1.0.02' on the admin of my router shows my router really * is * a E4200v1.

  Just in case anyone else has this problem - I have just flashed with build 18777 BrainSlayer's DD - WRT wiki (Google it).

  Everything works now. It's a real shame for a large part of the cost of this router is so obviously lost in the software.

  I would recommend to anyone who knows what they are actually doing to purchase Draytek. Loads of features, no frills, it works.

  Good night

• View with PCOIP Wan

  Hello together,

  I had a problem with the connection with PCOIP on WAN.

  I can open my IE with https://externalviewserver:4172, but when I click on continue I don't have logon screen.

  After a while the IE wnt in timeout.

  Thank you very much for the help.

  Hmm, I think you got it wrong somewhere.

  You must install the client from view, he points to the broker to view http/https connections, authenticate and you can then choose a desktop computer to connect to.

  Linjo

• View 4.5 connect the session ends on the WAN access

  I saw 4.5 upwards and running, although I ran into a problem with connectivity from outside the network.

  I the installation of server Connection View and forwarded ports 80 and 443 to view connect server inside - it's a temporary facility until we run all over SSL VPN.

  I can reach the server, download the client, connect, but when he tries to establish the session on the desktop, it disconnects.  Newspapers the for the user login and logoff, as a the packet capture poster that my outside client ends the SSL connection after trying to connect.  This behavior is the same with the RDP PCoIP protocols.

  My question is: view you must install a server security for external connections, am I missing a port for PCoIP / RDP, or something in the roads is bad?

  I guess it depends on how if you use direct connect to this broker for connections.  If you use directly connect you must put at the disposal of the 3389 of VDI machines to the customer outside. If you are tunneling by this broker for connections, then it should work except PCOIP.   If I'm not mistaken PCOIP uses the direct connect method constantly.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

  Twitter: http://twitter.com/mittim12

• Back to my Mac drive remote access

  I tried to set up my Time Capsule and the hard drive connected to it to be accessible on the internet via Back to My Mac. My Time Capsule is the main router and the modem to the ISP provided is in bridge mode. I followed the instructions of installation to the letter, but it still not connect when I try to on the internet. I tried to connect life iPhone tethering and friend home as well with no luck.

  Tried to help out a little and when I go to the iCloud tab in system preferences, I get the following message on the CCMM: Back to My Mac can be slow because multiple devices on your network provides network services. Turn off NAT and DHCP on one of the devices and try again.

  The problem is that NAT is enabled, my Time Capsule is set up for back to my Mac and I enabled sharing of files on it, as well as on WAN access records. I also tried the deactivation and activation CCMM on both Time Capsule and in settings iCloud, still the same error. My only goal is to be able to connect to the Time Capsule and access the files remotely.

  I hope someone can help.

  Thank you!

  provided the ISP modem is in Bridge mode

  It may or may not be, because ISPS generally have some strange ideas about what the term "Clipping" might mean.

  What is the number and model of your modem?

  If all goes well, it is a simple modem.. .with a single Ethernet port the device... as in the example just below, which is the type of device that you really need to be able to access on your network from the Internet devices.

  

  I hope once again, it is not a type of modem/router or gateway device, which combines the functions of the modem router and separated in one package... as in the example below. Often, it is not possible to configure this type of law only as a simple modem device... and what the ISP calls 'Clipping'... is not really. Thus, you're left with a problem NAT which slows down and restricting remote access.

  

• RV042 access rules

  I have a port forward for a port (say 3299). I also have a Wan access rule allowing all traffic from several IP ranges to access the local network.  Other wan access is refused by the built-in firewall rule.  However, I can still access the port forward despite this.  What I have to do a rule specifically for the port to allow access to the range of IP addresses and blocking everything else.  I thought that the integrated Wan rule deny it, everything, everything, always treat that...

  Thoughts?

  Hi, I thought the same as you before, but I had the same problem with my FTP rules.

  Because you did a redirect rule, you create also allows some first IP you want access to this transfer and later, you must do a deny rule for this redirection service that rejects everything after tent.

• Cisco SR520 - no outgoing access

  This is the current configuration of the router. Can someone tell me why my (192.168.x.x) clients cannot access the internet through that router?

  See the race
  Building configuration...

  Current configuration: 10699 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname SR520
  !
  boot-start-marker
  boot-end-marker
  !
  forest-meter operation of syslog messages
  enable secret 5 $1$ K5vy$ E90Ebf679MAMz.wglbYsJ.
  !
  No aaa new-model
  clock timezone STD - 7
  clock to summer time recurring MDT
  !
  Crypto pki trustpoint TP-self-signed-1548662293
  enrollment selfsigned
  -More - name of the object cn = IOS - Self - signed - certificate - 1548662293
  revocation checking no
  rsakeypair TP-self-signed-1548662293
  !
  !
  TP-self-signed-1548662293 crypto pki certificate chain
  certificate self-signed 01
  3082024E 308201B 7 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 31353438 36363232 6174652D 3933301E 170 3039 30383231 31393030
  33335A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 35343836 65642D
  36323239 3330819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  8100B9BC 7D728F83 7D6059FD 49210310 F04FB968 4440ACD0 B16C927B 8AA215C2
  829 166FC 79F9CF75 ADAADACE 97292EA9 3C7DAFF6 EA5F6B8C 1FD00813 144DB9E8
  613744 D 47D1BCEF 344B268B 4 CBDA8579 A8B3D367 480CD3E0 687ACBF1 3E578E7A
  5583BE8C 9DD04F27 4060299E 0F212CF5 50F1F237 BDFC3CE6 87385AD8 D403A9E1
  36510203 010001A 3 76307430 1 130101 FF040530 030101FF 30210603 0F060355
  551D 1104 1A 301882 16535235 32302E64 6F6D6169 6E2E6163 7464736C 746 7030 D
  1 230418 30168014 DB9949FB 24128D3B 7528E6F3 8DBE4409 D4342BAF 1F060355
  301D 0603 551D0E04 160414DB 9949FB24 128D3B75 28E6F38D BE4409D4 342BAF30
  010104 05000381 8100B95F C4A4AC82 57974A6D 181D601F 0D 864886F7 0D06092A
  A2189179 25D9764A FBA8513B 94FC17E4 34F2D097 C40DD507 F0595CB5 B 538, 0296
  -Other - 39866542 F1DA78C0 A09B469F 739C2FB0 A54B1367 DA88ECFF D51FE907 56E8E06D
  33412A9D C9A57B60 2DAF85E1 B5A84E60 C740962B 525D72B3 883BBBC1 47A5AD4A
  F8F25292 813AEC2B BD37B55A 96A2A177 666TH
  quit smoking
  dot11 syslog
  IP source-route
  !
  !
  !
  !
  IP cef
  name of the IP-server 209.161.4.218
  !
  No ipv6 cef
  Authenticated MultiLink bundle-name Panel

  parameter-card type urlfilter SDM_URLFILTER_MAP
  exclusive-domain license wendell.k12.id.us
  exclusive-domain license mail.wendellschools.com
  exclusive-domain license k12.id.us
  exclusive-area permit www.teenbiz3000.com
  exclusive-domain license mail.safelink.net
  exclusive-domain license www.sd232.k12.id.us
  -More - exclusive mail.wendellschools.org allowed domain
  exclusive-area permit bing.com
  exclusive-domain license google.com
  license exclusive-domain yahoo.com
  parameter-card type regex sdm-regex-nonascii
  model [^ \x00-\x80]

  type of parameter-map protocol-info msn servers
  Server name messenger.hotmail.com
  Server name gateway.messenger.hotmail.com
  Server name webmessenger.msn.com

  type of parameter-card aol-server protocol-info
  Server name login.Oscar.AOL.com
  Server name TOC.Oscar.AOL.com
  Server name oam - d09a.blue.aol.com

  type of parameter-map protocol-info yahoo servers
  Server name SCS.msg.Yahoo.com
  Server name SCSA.msg.Yahoo.com
  Server name scsb.msg.Yahoo.com
  Server name SCSC.msg.Yahoo.com
  Server name scsd.msg.Yahoo.com
  -More - cs16.msg.dcn.yahoo.com server name
  Server name cs19.msg.dcn.Yahoo.com
  Server name cs42.msg.dcn.Yahoo.com
  Server name cs53.msg.dcn.Yahoo.com
  Server name cs54.msg.dcn.Yahoo.com
  Server name ads1.VIP.SCD.Yahoo.com
  Server name radio1.launch.VIP.DAL.Yahoo.com
  Server name in1.msg.VIP.RE2.Yahoo.com
  Server name Data1.my.VIP.SC5.Yahoo.com
  Server name address1.PIM.VIP.mud.Yahoo.com
  Server name edit.Messenger.Yahoo.com
  Server name Messenger.Yahoo.com
  Server name http.pager.Yahoo.com
  Server name privacy.Yahoo.com
  Server name CSA.Yahoo.com
  Server name CSB.Yahoo.com
  Server name CSC.Yahoo.com

  !
  !
  username admin privilege 15 secret 5 $1$ $9EbE 21QHkuUvg3blkmWNXibqM1
  !
  !
  --More--                           !
  Archives
  The config log
  hidekeys
  !
  !
  !
  type of class-card inspect any match of sdm-app-smtp smtp
  corresponds to the length of the gt 5000000 data
  type of class-card inspect any match http sdm-app-nonascii
  req-resp header sdm-regex-nonascii regex match
  type of class-card inspect any match of sdm-app-imap imap
  match zero-order
  type of class-card inspect all match sdm-cls-Protocol-p2p
  edonkey signature Protocol game
  match the signature of the gnutella Protocol
  match the signature of Protocol kazaa2
  match the signature of the fasttrack Protocol
  match the signature of bittorrent Protocol
  type of class-card inspect all SDM-voice-enabled game
  h323 Protocol game
  Skinny Protocol game
  sip protocol game
  -More class-map type - inspect correspondence sdm-protocol-pop3
  pop3 Protocol game
  type of class-card inspect all match sdm-cls-icmp-access
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect all match sdm-cls-Protocol-im
  yahoo-servers Protocol ymsgr match
  msnmsgr msn-protocol servers match
  match aol aol-protocol servers
  type of class-card inspect all sdm-cls-insp-traffic game
  dns protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  tcp protocol match
  udp Protocol game
  type of class-card inspect any match of sdm-app-pop3 pop3
  match zero-order
  type of class-card inspect correspondence sdm-Protocol-p2p
  corresponds to the class-map sdm-cls-Protocol-p2p
  type of class-card inspect any match http sdm-http-blockparam
  -More - match request port-abuse im
  request game port-bad use p2p
  match request port-abuse tunneling
  req-resp-violation of Protocol game
  type of class-card inspect correspondence sdm-Protocol-im
  corresponds to the class-map sdm-cls-Protocol-im
  type of class-card inspect correspondence sdm-invalid-src
  game group-access 100
  type of class-card inspect the correspondence dhcp_out_self
  match access-group name dhcp-RESP-licensing
  type of class-card inspect the correspondence dhcp_self_out
  match access-group name dhcp-req-licensing
  type of class-card inspect any match http sdm-app-httpmethods
  request method bcopy game
  request method bdelete game
  request method bmove game
  request method bpropfind game
  request method bproppatch game
  method of application for game connect
  match request method copy
  delete the method of application of game
  match request edit method
  match request method getattribute
  -More - match request getattributenames method
  match request getproperties method
  is the index of request method
  request method lock game
  match request mkcol method
  match request mkdir method
  method of application for game go
  method of application for match report
  match the options request method
  survey method match request
  request method post game
  match request propfind method
  match request proppatch method
  put request method match
  match request method revadd
  match request method revlabel
  match method revlog request
  request method revnum game
  method of application for game save
  is looking for the query method
  match request method setattribute
  request method startrev game
  match request method stoprev
  -More - match request method to subscribe
  match request method trace
  match unedit request method
  method of application for game unlock
  unsubscribe request to match method
  type of class-card inspect correspondence sdm-Protocol-http
  http protocol game
  type of class-card inspect correspondence sdm-protocol-smtp
  smtp Protocol game
  type of class-card inspect correspondence sdm-Protocol-imap
  match the imap Protocol
  !
  !
  type of policy-card inspect sdm-permits-icmpreply
  class type inspect dhcp_self_out
  Pass
  class type inspect sdm-cls-icmp-access
  inspect
  class class by default
  Pass
  type of policy-card inspect http sdm-action-app-http
  class type inspect http http-sdm-blockparam
  Journal
  -More - reset
  class type inspect http sdm-app-httpmethods
  Journal
  reset
  class type inspect http sdm-app-nonascii
  Journal
  reset
  type of policy-card inspect sdm-action-smtp smtp
  class type inspect sdm-app-smtp smtp
  reset
  type of policy-card inspect sdm-action-imap imap
  class type inspect sdm-app-imap imap
  Journal
  reset
  type of policy-card inspect sdm-action-pop3 pop3
  class type inspect sdm-app-pop3 pop3
  Journal
  reset
  type of policy-map inspect sdm - inspect
  class type inspect sdm-cls-insp-traffic
  inspect
  class type inspect SDM-voice-enabled
  Pass
  -More class type - inspect sdm-invalid-src
  Drop newspaper
  class type inspect sdm-Protocol-http
  inspect
  policy-service http sdm-action-app-http
  class type inspect sdm-protocol-smtp
  inspect
  policy-service smtp sdm-action-smtp
  class type inspect sdm-Protocol-imap
  inspect
  SDM-action-imap imap service-policy
  class type inspect sdm-protocol-pop3
  inspect
  SDM-action-pop3 pop3 service-policy
  class type inspect sdm-Protocol-p2p
  Drop newspaper
  class type inspect sdm-Protocol-im
  Drop newspaper
  class class by default
  drop
  type of policy-card inspect sdm-inspect-voip-in
  class type inspect SDM-voice-enabled
  Pass
  -More - default class
  drop
  type of policy-card inspect sdm-enabled
  class type inspect dhcp_out_self
  Pass
  class class by default
  drop
  !
  security of the area outside the area
  safety zone-to-zone
  safety zone-pair sdm-zp-self-out source destination outside zone auto
  type of service-strategy inspect sdm-permits-icmpreply
  safety zone-pair sdm-zp-out-in source out-area destination in the area
  type of service-strategy inspect sdm-inspect-voip-in
  source of sdm-zp-out-auto security area outside zone destination auto pair
  type of service-strategy inspect sdm-enabled
  safety zone-pair sdm-zp-in-out source in the area of destination outside the area
  type of service-strategy inspect sdm - inspect
  !
  !
  !
  interface FastEthernet0
  switchport access vlan 75
  --More--                           !
  interface FastEthernet1
  switchport access vlan 75
  !
  interface FastEthernet2
  switchport access vlan 75
  !
  interface FastEthernet3
  switchport access vlan 75
  !
  interface FastEthernet4
  Description $FW_OUTSIDE$
  DHCP IP address
  NAT outside IP
  IP virtual-reassembly
  outside the area of security of Member's area
  automatic duplex
  automatic speed
  !
  interface Vlan1
  no ip address
  !
  interface Vlan75
  -Description $FW_INSIDE$ more.
  the IP 192.168.0.1 255.255.252.0
  IP nat inside
  IP virtual-reassembly
  Security members in the box area
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 FastEthernet4
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  the IP nat inside source 1 list the interface FastEthernet4 overload
  !
  IP access-list extended dhcp-req-enabled
  Remark SDM_ACL = 1 category
  allow udp any eq bootpc any eq bootps
  IP access-list extended dhcp-RESP-enabled
  Remark SDM_ACL = 1 category
  allow udp any eq bootps any eq bootpc
  !
  access-list 1 permit 192.168.0.0 0.0.0.255
  -More - access list 100 remark SDM_ACL category = 128
  access-list 100 permit ip 255.255.255.255 host everything
  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
  !
  !
  !
  !
  !
  control plan
  !
  connection of the banner ^ CSR520 basic Config - MFG 1.0 ^ C
  !
  Line con 0
  local connection
  no activation of the modem
  line to 0
  line vty 0 4
  privilege level 15
  local connection
  transport input telnet ssh
  !
  max-task-time 5000 Planner
  end
  -More-
  SR520 #.

  OK, I heard about this once before, where the default basic configuration has been changed at the beginning of the life cycle of this product and WAN access problems were solved using a newer base from config.  Depending on your router, I have attached the default config, you can start with (or compare to yours).

  I'm not sure what has changed (I'm sorry)

  https://www.myciscocommunity.com/docs/doc-5167

• Black screen PCoIP

  I know that this issue was raised a lot and many solutions have been provided. But non of them helped me. Here's my network diagram:

  

  1. in the case with direct VPN static to the remote site, everything works fine. I can connect to the Thin Client (10.20.20.3) to View Server (10.10.10.2) and virtual (10.10.10.3) using RDP and PCoIP computer access.

  2. in the case when there is another router between the two, I can connect to the server from view but when I access VM via PCoIP, I see a black screen and connection breaks a few seconds later. RDP works very well.

  I followed solutions concerning the order of tools and agent installation. All ports between 10.40.40.3 and 10.10.10.2 are open.

  Any suggestions on how to solve the problem?

  Because RDP works it seems you have a problem with UDP (PCOIP) traffic. You say that all ports are open. They are open for TCP and UPD? Your router has some other parameter which allows to take the UPD packets? Can you read the router logs?

• PCoIP firewall ports

  I am under an environment of vmware view here and we have a pool with a few remote workstations that are used by system admins when they are working remotely or on-call incident response.  For security reasons, we have our servers segmented by VLANS and highly protected through Firewall (i.e. all traffic off the server WHAT VLAN is blocked explicitly).  For this reason, I seem to have a problem with is client vmware view to connect to remote workstations (inside the local network VIRTUAL server) via PCoIP.  I'm sure it's a firewall issue, because I can connect via RDP (ports that are open in the firewall) and I put temporarily in a rule to allow all traffic to the IP addresses of the remote workstations, which allowed me to connect through PCoIP, but immediately after the deactivation of this rule I have once more not connect through PCoIP.  Of course, the solution seems to be to open the ports of PCoIP remote work station, but after scouring the internets yesterday that I couldn't get a full list of ports, I need to open.  I looked at the article here http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1027217 and opening just tried these specific ports, but I still not can connect.  Someone at - it a complete list of ports to open?  I don't want to create a rule to open all ports for these machines.  Thanks in advance

  Suiname wrote:

  I forgot to mention that I am using view 5 and discovers not 4.6, I wonder if this changes anything in the ports that use the Protocol or implementation of PCoIP remote access.

  The same goes for 4.6, 5.0 and 5.1.

  Linjo is correct. For PCoIP is 4172 TCP and UDP 4172.

  Step 3 here described. http://communities.VMware.com/docs/doc-14974

  If you block PCoIP PCoIP fails and you will get a black screen for a few seconds, followed by a break.

  Run Wireshark on the Security server if it would help. You will see this traffic PCoIP.

  Let us know what it was. Thank you.

  Mark

• Problems with PCoIP secure Gateway

  I am using view 4.6 and faced with this configuration.  Under the "view Configuration", "Servers", then "view connection server" it shows my connection to the server.  The PCoIP column he says no secure portal is installed which is true.  See screenshoot

  

  the problem arises in the settings of the connection servers.

  When I select my connection to the server and fill in the external URL 'Tunnel secured HTTP (S)' and uncheck it ' user secure Tunnel connection to the Office I cam continue to use the internal connection server.

  When I check the box and check also the "gateway of PCoIP PCoIP connections for desktop machine, so this will work remotely, but not internally.  Also the external URL PCoIP is grayed out.

  To sum up I can't get this to work for internal or external use and not both at the same time.

  You can do this work with just a single server connection or an external as internal access, but it will mean that internal PCoIP is unnecessarily sent by gateway through a connection to the server or security server.

  It is best to dedicate servers to connect to internal and external to internal PCoIP direct access between the client and the virtual office.

  There is a detailed description of this http://communities.vmware.com/docs/DOC-14974 here, which includes a video detailing a deployment configuration of view for internal and external access.

  Select this option.

• Problem with iExplore to access the view manager

  Hi all.

  I installed a small lab environment to try VMware View 4. On the other hand, it's great.

  I m just use PCoIP to access my vDesktops.

  If I use VMware client View all works very well.

  But, when I try to access my vDesktop using iExplore (6 and 7) I get this error:

  "The Office has not opened (vDesk_XP_PoC). The Protocol to display for this office is currently disabled. Please contact your system administrator. »

  Any ideas?

  Best,

  Eduardo.

  
  
  If you found this information useful, please consider awarding points to 'Correct' or 'useful '.

  You can use PCoIP via the customer view and not view portal.  And it looks like you does not allow users to choose a different protocol (such as RDP using View Portal) when the pool was the installation.  If you authorize the change of Protocol, then it should automatically connect via RDP via view portal.

  -jonathan

• LDAP and APEX for access from home

  I am new to LDAP and only familiar with concepts so bear with me. I would like to know if I can use LDAP with an APEX application so that employees can access the LAN/intranet working system as well from home (or anywhere on the internet). They have access to the intranet via the LAN by signing on the use of their Novell username and password. I'm assuming that they can connect to the House using the same Novell username and password. (BTW-I don't want to set up APEX user ID or database user ID for users of 1800-1900). This can be accomplished? If so, how?
  
  I have a meeting with the vice-principal of the week next to discuss this project which it can manage access from the internet.
  
  
  Thank you in advance.
  
  Robert
  http://apexjscss.blogspot.com

  Hi Robert,.

  Yes, he is indifferent to the APEX where a user comes from. As I mentioned above, authentication is performed in the database by data that shows through the front. As long as the front-end server reaches the end back, your users can connect.
  The onlyl restriction that can be there is the Novell (LDAP) server not accepting does not request to the database server. But if you have LDAP works on your APEX for a LAN/WAN access, he will work with the reverse proxy as well.

  -Udo

• WiFi AR5007 802. 11 b / g adapter cannot talk about bridge WET11 Wireless on the same subnet

  Hello

  My HP Compaq Presario C700 VISTA laptop (a AR5007 802. 11 b / g WiFi adapter) and the printer are on the same subnet. The laptop is WiFi connected to my WRT54G2 router/switch and the printer is connected to the workgroup switch that connects to the router via the LinkSys WET11 Wireless Bridge.

  The installer works fine for over a year until he was there when my VISTA does not see any PC on the Working Group 3 weeks pass including the printer. However, the WAN access is not affected.

  I did the filming of following problems (in order):

  1. check the network settings on the laptop VISTA (x.x.x.29) and (x.x.x.201) printer and all look kosher.    (All my PC including notebook computer and printer have IP STATIC)

  2. check the router and the parameters of bridge and fines all eyes (router - XXX1, bridge - x.x.x.140).

  3 Ping printer, bridge, and other PC and received messages "Destination Unreachable Host" or "Request timed out". Although all are on the same subnet. Pingée router is OK.

  4 remove and re-add the wireless profile and tried to connect again. Same problem, no joy!

  5 started VISTA in safe MODE with NETWORK. Once again, the problem has persisted but at least eliminated applications as a potential source of problems.

  6. recycled power switch/router/workgroup bridge. No joy!

  7 WiFi connected other laptops to the same router (WRT54G2) and can ping other PC and printer END.    This means that the problem is limited to my VISTA laptop.

  8 given that the problem is on my VISTA and applications are not the source (see #5) of the problem, then probably the AR5007 802.11b.g wireless network card driver is original so I downloaded driver at HP and installed with version 7.3.201.25.  Problem is persistent...  Arhhh!

  Could there be something else that I missed? Can someone please help.

  Thank you

  You are the very welcome, John.

  Yes this driver will work fine on Vista Home Premium.

  According to the notes on the driver, it can just be run without uninstalling the current pilot you have on there now.

  After executing, you can confirm it 'takes' by going into Device Manager, expand network adapters, click the atheros wireless card, click the driver tab and you should see the installed version 2011.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• installation confusion 6224

  I'm trying to configure a 6224.  I have reset to factory settings so much times again now and I am very frustrated.  This is my first time up to a layer 3 switch setting.  My config running can be started on easy enough if someone could possibly help me out here.

  I have a CentOS box as a router IPTables which is running out and realized that it was better for me to go to a layer 3 switch (6224 was recommended) since I can't afford a standalone router device.  I was able to take place a 6224 news at an incredible price.

  (The WAN IP addresses below have been changed for this example)

  My upstream provider says my router must be IP address 22.104.86.50/30 (22.104.86.49 bridge).  I have a 22.100.100.0/24 class C that my servers will need and want to run a LAN using 10.0.0.0/8

  I wanted to g1 - g12 as ports WAN my C class would be to connect (using 22.100.100.1/24 as the gateway to the 6224)

  I tried g13-g23(or g24 if I don't need one specifically for my 22.104.86.50/30 address) as my LAN addresses

  LAN addresses, of course, do NOT need WAN access because they are only for internal use between servers.

  I had my VLAN 1 put in place with the 22.104.86.50/30, 22.100.100.0/24 VLAN 10 and VLAN 20 with 10.0.0.0/8.  I "had" VLAN 1 assigned to g24 and plugged my cable WAN it.  I can access the GUI from a remote IP address in this way.

  I got 10 VLAN configuration with 22.100.100.1 as the IP address and can access the GUI if I plug into ports g1 - g12 to this address.

  I had 20 VLAN configuration with 10.0.0.1/8 and can access the GUI if I plug into ports g13 - g23 at this address.  Yes, I manually configure my laptop address to be in these with those of the VLAN IP as gateway.

  The problem is with this configuration, VLAN 10 can't get out to the internet.  VLAN 20 isn't, but I don't want it to be able to.

  Any one any help would be greatly appreciated as I worked on it for 10 hours now with no luck in getting it to access the internet.  I have google so many times I should go stock inside out.

  Thank you in advance,

  Steve

  

  I would use the diagram above as reference to describe how you define your internet connection upstream connection.

  Basically, you need to set up a VIRTUAL LAN between the PowerConnect 6224 switch and your upstream provider.  In this scenario 1 switch would be the 6224 and switch 2 is the upstream provider.

  On the 6224, you create a VLAN 100 (or whatever the ID # you choose).  Then set the ip address to this VLAN to 22.104.86.50/30.  Then go into the physical interface or a DELAY.  It must be a single connection or a DELAY (multiple physical connections working as a virtual port channel).  The interface would be created as switchport mode access for 100 of VLAN.

  Example:

  Console > activate

  Console # config

  Console (config) # ip Routing (active routing in the world)

  Console (config) # vlan database

  VLAN console(config-VLAN) # 100

  output console(config-VLAN) #.

  Console (config) # interface vlan 100

  ip address console # 22.104.86.50 255.255.255.252

  Console # routing (active routing for the VLAN specific)

  output console #.

  Console (config) # interface ethernet 1/g1

  access mode console (config-if-1/g-10) #switchport

  Console (config-if-1/g10) #switchport access vlan 100

  Then you would look to create a VLAN for your other local networks in a similar way. Definition of VLANS and ip address for the VLAN.  Then affecting all physical ports in the access mode for this VLAN.  Then some devices end of PC that are plug that coelio VLAN would have an ip address in this range of network and a gateway IP address you set for the VLAN itself.

  I hope this helps, let us know if you have any other questions