PERC H200A

Similar Questions

• Replacement H200A PERC - inactive volumes RAID - controller okay to activate?

  Hi all, quick question which I * think * I know the answer, but it's a new one on me and all juggling RAID settings in a live environment make me sweat.
  Situation, is that I have a PowerEdge T410 with a PERC H200A controller and two RAID 1 volumes, 600 GB, and 1 TB.  Was a message of "Fatal error 4 Bus Slot" in OpenManage and diagnosis, which points to the H200A, and as a result, the server is not feeding properly in ESXi and one of the volumes is showing that the East in vCenter.  It will not mount.

  Fortunately, I have a spare H200A controller, so I put it in the server and, as expected, is to show the RAID volumes as being inactive.  I'm * assuming that * I can activate just them and they will come to life, but I just wanted to check if somebody do it before and I can confirm that is going to work.

  Thank you

  Tim.

  Yes, you must activate the VD/table. Real PERC, the controller would see a configuration on the discs and you could import the foreign configuration... the terminology on this controller is that he sees a configuration on the disks and you must activate it.

• H200A PERC. SAS and SATA. Simple 2 extra HARD drives raid. Possible?

  Hello.
   
  Research in the server rack dell R210 II.
   
  Added records 2 x 300 GB SAS with a PERC H200A raid controller.
  The other two empty drive bays im looking to transfer courses two SATA 2.5 "HARD disk drives. Ive read you can mix SATA and SAS drives, is this true?
   
   
  I have two options to the raid configuration:
   
  the raid controller would be able to support two raid 1 RAID. 1 for the SAS drives and the other for the two SATA drives?   Operating system can see two disks.
   
  He would support a raid 1 for hard 1 & 2 discs.  Then with disk HARD 3 & 4 show the HARD drive directly on the server.  OS sees thre readers.  The drive in question and two others.
   
   
  I tried the dell chat, but could not get anywhere, as the helpdesk agent does not seem to know that you can google some caddy and buy the caddy to adapt to discs with no carts.

  [murmur] I'm wrong :), but I think the H200 supported not RAID, so if left unconfigured, the disks will be seen by the operating system as the person/no RAID disks.  Also, if I am wrong not :), the H200 supports a maximum of 2 virtual drives, so would not work two 1-disk RAID 0 and a RAID 1 (in fact, it probably won't allow you to create a single drive RAID 0 in all). [/whisper]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_dell_adapters/PowerEdge-RC-h200_User ' s%20Guide_en-us.pdf

  Sorry... I love you pc :)

• How to upgrade readers in my H200 RAID of larger size and SATA to SAS

  We are upgrading hard drives in our Dell Poweredge T110, equipped with a PERC-H200A and two in RAID 1 TB mirrored SATA drives. We run the Dell T110 of ESXi 5.1 version and a single Windows Server Essentials 2012 VM.

  We want to double our capacity of hard disk and the Support of Dell sold us 2 x 342-1020 (2 TB 7.2 K NL SAS, 6 G, 3.5, CB, CK) readers.

  What is the easiest way to replace the existing SATA disks in the RAID with these new disks in the same configuration and EXSi / VM / OS?

  The controller manages RAID creating the new RAID and copy the data through somehow?
  I add the new disks in a second DiskVolume and build a second (SAS) RAID and then somehow to clone or copy the original (SATA) RAID to the new then pass the boot device to the new (SAS) RAID?

  Thank you
  Dan

  It is a different scenario than what addresses this thread, but to answer your question: Yes, you can remove a 1 TB SAS drive and replace it with another drive SAS to rebuild.

• Dell PowerEdge C2100 FS12-TY unknown Expander, PERC 6i/r - error (?) dDm

  We have a couple C2100s Bay 12, we recently acquired. Unfortunately we are unable to make it work right. When we try to access the raid configuration utility it says "dDm" and then hangs, you gotta pull the plug to reset. We tried it on all of them. We passed on the PERC 6i/r with another and then it gives us an error "direct drive mapping". The firmware on the PERC 6i/r pre-installed does not exist anywhere.

  We have never seen the "dDm" message before, so we do not know what to do with him.

  I actually thought about it. Flash the latest firmware perc6i on the perc6i with that he came. Use the megafl.exe commands, not the update.bat.

• PERC S300 and R2 2012

  Hi, I saw some documents last year which says that Dell does not intend to create a driver for use with the Perc S300 and R2 for Windows Server 2012. This situation is even position? If Yes, what is the best option for my brand new PowerEdge R210 II? I would rather use hardware RAID than software RAID on what happens to be a domain controller. The server has two installation disks in a RAID 1 array. Any help, suggestions and advice are welcome. Thank you!

  Dell_S100-S110-S300_Driver-WindowsServer2012r2

• PERC H700 driver during Windows Server 2012 r2 - disk Raid not recognized not

  Hello

  I try to install a r2 Windows Server 2012 to a Poweredge R710 with a Raid Perc H700. 2 HDD in Raid 1, but the HARD drive is not rcognized Italian Installation even if I try to use the 2008 r2 for the Perc Raid driver. They are listed, but if I select one disk HARD are not visible. What should do?

  Best regards...

  Grolle,

  Leave in the Raid Controller, what is the status of the table? In addition, was the raid 1 initialized after being created? If this isn't the case, then, who will have to be done before you try to install.

  If you download this and start on the lifecycle controller (F10) and then select deploy BONES, load these files there and proceed with the installation of the OS.

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=M5VGR&FILEID=3325059394&osCode=MWS80&ProductCode=PowerEdge-R710&LanguageCode=en&CategoryID=DD

  I would like to know how will install it.

• PERC H310 H710p migration

  Hello

  I'm not an expert in RAID configurations but I am in charge of server Dell T320 my company and we will replace the storage controller that comes with it (H310) with a PERC H710p. We have a configured RAID-1 and we will continue to use the two disks of same after migration. We will replace the controllers.

  I know I have to do a backup before you replace the Exchange, but we will lose the RAID-1 configuration and data (including the operating system) after migration? Or it will be transparent to the system after reboot?

  Where can I find a type of paper that could guide me through this process because I don't want to wreck anything.

  Thanks a lot for your help.

  Jorge

  Hello.

  It is advisable to back up your data before performing any maintenance task. Ensure that you have a backup is valid data. The PERC H710 P supports the migration of virtual disk controller PERC H310. As a best practice, make sure that the hard drives and firmware H710 P is up to date. Replace the H310 and update the H710 P firmware with the controller cables disconnected from the background. Stop the server and connect the cables of the controller in the background and then restart.

  Your RAID configuration can be transparent to the system or appear in a foreign configuration. Clear the foreign configuration through the utility OpenManage Server Administrator (OMSA) or Ctrl + R for the POST.

  I would like to know how it works for you.

• Dell Power Edge R410 & Dell Perc H700 modular F2WGY

  Hi guys

  Need some advice please, a few weeks ago, we bought a Dell R410. This came with a modular 6/ir Perc. However, when we arrived at the installation of drives we noticed that the controller did not recognize disks larger than 2 TB. It's not good because we need to use 2 x 3 and 2 x 500 GB disks in a RAID 1 Configuration.

  After Googling autour, I came to the conclusion that the card that it came with the "Perc 6/ir' does not support disks larger than 2 TB.

  So, I advanced and bought a new modular a "Dell Perc H700 F2WGY" controller which apparently supports disks more great.

  the controller came yesterday so I removed the old Perc 6/ir controller from the slot in the bottom of the map editing and trendy "Dell Perc H700 F2WGY" modular at the same place. : Photo of slot, I inserted H700

  H700 card: see picture

  PERC 6/ir map: see picture

  Anyway, once I inserted the card and started, I was presented with the error; "PCIE training error" system HALT.

  Obviously this would not start any further. So I brought the wrong card? im confused at the moment between modular and integrated? the pcie slot is low for integrated only cards?

  I then add the new map on the PCIE Top slot. the system then started and he could see the card. However, it found no readers?

  What exactly I do bad will this card work at all? or I'm out of luck and need another card?

  Cappilio,

  The problem you are experiencing is due to the model of the H700. Map H700 modular version is actually designed for the blade server Poweredge series. The model that you would need is the H700i which is the version that is integrated, designed to go into the white storage controller slot you are talking about. The references are KK67X and CNXVV. The latest model of the H700 is the H700A which is the adapter, it's the model that is necessary for installation in a PCIe location.

  This link explains in detail in the overview H700 - http://www.dell.com/downloads/global/products/pvaul/en/perc-technical-guidebook.pdf

  Let me know if it helps.

• SSD compatibility w/PERC S300 RAID?

  We have an old PE T110 first generation with a PERC S300 RAID controller and 4x250GB drives. However, because the controller is older, there isn't much documentation about SSD compatibility. Does anyone at - he had success the upgrade of any server/workstation using a PERC S300 with an SSD of any kind in a RAID 10 configuration?

  Finally, I don't remember what type of connector is on the existing disks and am a little confused about the difference between SATA and SAS. What normally comes stock with this system and which would need if I moved to SSD? New cables? Anything else I need to know?

  htc2010

  is it not reasonable to assume I could just as easily swap on each drive in the Bay, one at a time, with a SSD?

  You cannot mix SAS and SATA drives in the same array. Also, you cannot mix HDD and SSD. If SSD does not support the S300, then he cannot know the difference between a SATA SSD and a SATA HDD, so it can work, but 1) I wouldn't rely on it and 2) just know that real RAID controllers, it can be done.

  In the end, I don't know if she will achieve your goals. The reason why I asked is because you could just add the SSD as a new VD, then move the files of database, etc. on to improve the speed, but it sounds like a lot of work for little return. I just invest in a backup recovery solution, good. If it can work in a virtual environment?

• Battery on the Controller PERC 6 / i integrated Poweredge R900 and 2950.

  Hi, we have this error below Poweredge R900 and Poweredge 2950 for 4 days now, I hope that he will be gone after 7 days (such as by Maximum learning delay)

  Battery on the Controller PERC 6 / i integrated:

  Name battery 0
  Degraded state
  Loan of State capacity
  Learn the State duly
  Next time learn 0 hours
  Learn 7 days 0 hours maximum
  Learn the Auto Mode

  In case the error continues after 7 days, is there any solution to this? or replace the battery if error remains.

  I had been searching for the right part No. battery so that we can order in advance, thank you for giving the battery part No. for Poweredge R900 and 2950 Controller PERC 6 / i integrated.

  Thank you much in advance.

  concerning

  Rais info is stored on the discs should not be a problem

  R900 page 84 support.dell.com/.../XK9460D.pdf

  2950 page 74 support.dell.com/.../hom.pdf

• Batteria PERC H710P

  Buonasera,

  Ho una Controller PERC H710p.

  Avrei need del kit batteria (cavo + batteria) da applicarvi. The controller e stata dismessa mesi fa (betteria era esausta pertanto above serve necessitar) e probabilmente it cavo e stato cestinato complete alla batteria

  Grazie.

  Buongiorno,

  non esiste an acquistabile como iPhone by the e batteria KIT it cavo.

  UN unica soluzione e acquistare by take support ticket it supporto tecnico e quindi sostituzione della batteria.

  www.Dell.com/.../SS

  Marco

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• T330 replace PERC S130 with H330

  Hello

  I have a T330 with the PERC s130 currently and you need to add 2 additional drives for a total of 6. As far as I can tell that the S130 is not able to add more 4 readers so I wanted to know what would be the part number for the H330 PERC? Do I need something else outside the H330 map? The server is already equipped with background and hot swap SATA drives.

  Thank you!

  Kind regards

  Howard

  Hc2995,

  The part number for the controller H330 is 4Y5H1. You should not need probably the cable (part P9VFY) withyou exceeding is not 6 hard drives.

  Let me know if this can help, or if you have any questions or concerns.

• R210 with PERC H200 will increase the possibilities for HD

  I have a PE R210 w/PERC H200.  The RAID configuration is RAID 1 2 HD.  I was looking at options to increase the storage capacity.  Someone please correct me if I'm wrong, but I read that it is not possible to extend the VFD by improving each hd one at a time to rebuild the RAID VD, then its extension to occupy unused space in HD.  There is no other HD slots available on the R210, along with options to do I have if I want to keep the current VD but increase the storage space on the server?

  Backup, replace the disks with the biggest, configure RAID, restore from a backup.